Search Documents

By E. R. Mueller

The natural lives of machines and components vary tremendously! Maintenance managers struggle constantly to maximize their equipment lives while minimizing their maintenance costs, but they normally lack the tools and techniques they need to do this properly. This paper proposes a methodology based on probabilities of failure and expected values for repairs that recognizes the variation among individual machines and components as well as the high costs associated with catastrophic failures. It enables a user to determine the optimum change-out intervals for many types of equipment. The approach proposed here is sophisticated enough to be reliable but simple enough to be applied by the maintenance staff on the shop floor. It will complement existing preventive and predictive maintenance programs.

Jan 1, 1995

By G. M. Castillo

Newmont?s Phoenix mine started production in March of 2006. Due to the extreme hardness of the ore, the mill has struggled to meet throughput projections. Grinding studies showed that optimizing the existing circuit would not achieve budgeted throughput. These studies also showed that the pebble crusher was being underutilized due to the inability of the SAG mill to break the rock. The concept was developed to supplement the feed to the existing pebble crusher with a secondary crusher. Models of this process looked favorable so a portable crusher was installed to test the process. The temporary crusher was successful at increasing the throughput by 7% and based on the operating data, plans are currently being developed to install a permanent secondary crushing system in front of the SAG mill. This paper will review the results from the test crusher and the flow sheet for the permanent secondary crusher.

Jan 1, 2012

By Marcela Alves Silva

Os aços inoxidáveis duplex - AID são ligas de Fe-Cr-Ni com no mínimo de 10,5% de Cr, promovendo uma película superficial aderente de Cr2O3, com proteção a corrosão e proporção microestrutural de austenita e ferrita próximas a 50%, potencializando as propriedades mecânicas e resistência à corrosão.Possuem boa soldabilidade, porém pode provocar um desbalanceamento microestrutural e a precipitação de fases deletérias, acarretando o declínio das propriedades, principalmente na zona afetada termicamente – ZTA. Desta forma o presente trabalho tem como objetivoavaliar à influência da energia de soldagem sobre a ZTA da junta soldada de AID, comparando soldas realizadas pelo processo TIG e FCAW levando em consideração o balanceamento das fases ferrita e austenita. Para tanto, foram realizadas soldas com parâmetros comumente utilizados nas indústrias em geral. As amostras apresentadas foram soldadas de acordo com o padrão da Thermon Indústria Mecânica, uma das colaboradoras deste projeto. Conclui-se que a comparação entre os dois processos distintos resultou em fatos já esperados, embasado na revisão bibliográfica, onde o corpo de prova soldado pelo processo TIG apresentou menor região propensa a fragilizações, menor ZTA. As frações de austenita e ferrita em cada corpo de prova foram similares nesta região.

Aug 17, 2017

By Júlia Mont’Alverne Martins

A Votorantim Metais processa pós de aciaria elétrica (PAE) e outros resíduos contendo zinco em sua unidade de Juiz de Fora, por meio do processo Waelz. Devido ao alto teor de óxido de cálcio (CaO) nos resíduos processados, a etapa de desalogenação apresenta baixo rendimento de remoção de fluoretos -aproximadamente 20%. O processo de lixiviação sob pressão foi testado para o tratamento de amostras de óxido Waelz (O.W.) da Votorantim Metais com o objetivo de lixiviar os cloretos e fluoretos contidos nesse material. Os parâmetros avaliados foram: temperatura de lixiviação (120°C a 180°C) e razão de carbonato de sódio (Na2CO3) adicionado (100kg/t a 200kg/t óxido Waelz), em um reator piloto com capacidade de 10L. A técnica mostrou-se eficiente para lixiviação de cloretos, com remoção acima de 94,2%. Os resultados para fluoretos obtidos apresentaram variação entre 63,0% e 96,2% de rendimento de lixiviação e uma forte correlação dos resultados com a temperatura. Esse processo mostrou-se eficiente em escala de bancada, apresentando rendimento de extração superior a 90% para a remoção de halogênios em temperaturas acima de 150°C e adição de Na2CO3 de 140 kg/t O.W.

Aug 17, 2017

By Raymond Derzay

This publication is intended to be of value to the mineral industry in establishing and maintaining effective programs for preventing noise-induced hearing loss. Factors involved in this loss and the need for and the requirements of an effective hearing conservation program are discussed. The legal and legislative history of compensation for hearing loss is briefly reviewed. A review of statutes is not attempted since several States have recently modified) or are in the process of modifying their laws regarding permissible noise exposures) required hearing protection) and/or compensation for hearing loss. A review of other aspects of the problem of industrial noise in terms of medical, physiological) and psychological frames of reference is included. A hearing conservation program is described in detail. Appendixes detailing the names and addresses of a few equipment suppliers are included. References are provided for those who may wish to delve more deeply into the medical, technical, and scientific considerations of noise and its effect on man.

Jan 1, 1972

Use instantaneous sampling to pinpoint dust sources and to Improve dust control on longwalls. Approach Use a dust monitor developed under a Bureau contract. How It Works Sampling can be done by either a moving or a stationary method. In the "moving' method, the dust monitor is carried by a survey engineer walking at the midpoint of the shearer Dust levels and face position (support number) are taken during all phases of the mining cycle while the shearer is cutting. These measurements can show how changes in airflow along the face, face specific; (rock partings) and cutting sequence (cutting the wedge) variables affect dust levels. In the "stationary sampling" method, the survey engineer stands with the RAM at a fixed location on the face. As the shearer approaches, the dust level and the distance to the shearer are recorded at 10-second intervals. Typically measurements start when the shearer is 20 feet from the sampling position and continue as the shearer passes the position until it is 20 feet away on the other side. Dust profiles around the machine are obtained at several fixed locations along the face only while the shearer is cutting.

Jan 1, 1982

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery ? Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery ? Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2012

By Sidiney Nascimento Silva

O presente trabalho teve como principal objetivo avaliar, em escalas laboratorial e industrial, a viabilidade técnica e financeira da aplicação da escória de Aciaria LD (EAC), em combinação com a escória granulada de Alto-Forno (EAF), à produção de Cimento Portland CP III. O projeto de pesquisa em questão foi desenvolvido pela CSN, através de Convênio de Cooperação Técnica e Econômica com a Escola de Engenharia de Lorena, EEL, da Universidade de São Paulo, USP, e compreendeu as seguintes etapas: i) caracterização físico-química e mineralógica da escória de Aciaria LD da CSN; ii) desenvolvimento do processo adicional de beneficiamento da EAC para aplicação na produção de cimento; iii) testes laboratoriais visando a avaliar a viabilidade técnica; iv) testes industriais com a finalidade de validar os testes laboratoriais e selecionar a formulação de melhor desempenho; v) estudo de viabilidade financeira; e vi) implantação do projeto. A aplicação da escória de Aciaria LD da CSN na produção de Cimento Portland CP III, em combinação com a escória de Alto-Forno e clínquer, é viável técnica e financeiramente. Isso traz reflexos positivos para o aumento da competitividade do negócio Cimento, aumenta a recuperação de metálicos para reciclagem nos processos siderúrgicos da UPV (negócio Siderurgia) e reduz passivos ambientais.

Aug 16, 2017

By Carline Fabiane Stalter

O presente trabalho tem por objetivo buscar e aplicar ações de P+L no processo de colagem. Este é realizado em uma cabine de formato cúbico, cujo material colante é o adesivo de poliuretano. Como a aplicação sobre o substrato é feita com uma pistola específica, ocorre a formação de névoas e consequentemente sua deposição nas paredes da cabine, formando camadas de adesivo que devem ser removidas e descartadas como resíduo. A fim de facilitar sua remoção, as paredes eram revestidas com graxa, que acabava contaminando o resíduo. Com as ações de P+L, buscou-se eliminar a graxa do processo. A partir daí, foi realizada a avaliação econômica e ambiental. A melhor opção para eliminar a graxa seria utilizar um produto que agisse como desmoldante, por isso foi testado o tecido de fibra de vidro com Teflon®. Como os testes realizados apresentaram resultados satisfatórios, houve a substituição da graxa. Dessa forma houve a redução de custos e no tempo de limpeza da cabine, não geração de graxa como resíduo, possibilidade de reaproveitamento do resíduo, eliminação do contato entre o operador e a graxa, transformação de um resíduo classe I em classe II e retorno financeiro do valor investido em 1,1 meses.

Aug 16, 2017

By R. Y. Wan, J. R. Parga, J. D. Miller

The direct recovery of precious metals from a1kaline cyanide solution is frequently accomplished by the well-established Merrill-Crowe process involving zinc-dust cementation. This is particularly true for silver. Plant data from two operations are presented and analyzed in terms of intrinsic reaction features. In such Merrill-Crowe plants a plate-and-frame filter press acts as a semicontinuous fixed-bed reactor with a distribution of particle retention times. For the plants studied, 99Yo of the silver is recovered with a solution retention time of less than 2 min. Differences in plant operating conditions and product characteristics can be related to the nature of the surface deposit of silver which forms on the zinc particles. From laboratory experiments and plant samples it has been found that the presence of lead in the system activates a change in the silver deposit morphology to the dendritic state which affects the rate of silver deposition as well as the filter cake porosity. Finally the plate-and-frame press is considered from an engineering perspective as a semi- continuous fixed - bed reactor to describe the behavior of the system.

Jan 1, 1987

One of the major objectives of cost analysis is to enable the manager to predict the financial outcomes of decisions. To accomplish this, the future costs and benefits of alternative courses of action must be determined. If care- fully used, information about past financial performance can be helpful in this analysis despite the fact that, by definition, financial reporting information is historical. In many cases, both revenues and costs need to be estimated for decision- making. For the production manager, additional revenue is a result of increased throughput or recovery of valuable material from the stream of mined material. A reduction in operating cost, although similar to a revenue increase in its financial impact, is estimated using slightly different techniques. Generally, the estimation of cost is more difficult than the estimation of revenue. Most cost estimates have two components: an estimate of fixed costs and an estimate of variable costs. As discussed in chapter 5, the total cost of an activity during a specified period can be expressed as: Total cost = (Variable cost per unit of activity) x (Units of activity) + Fixed cost or TC = VX+F

Jan 1, 1999

By Vinicius de Oliveira Fidelis Sales

O presente trabalho tem como por objetivo a busca por uma solução eletrolítica capaz de eletropolir, eficientemente, amostras de ferro puro (>99,8% Fe). A finalidade de se utilizar o ferro é devido o interesse em suas propriedades biocompativeis e a sua possível aplicação biomédica, sendo utilizado em dispositivos biodegradáveis. Ligas à base de Fe, Mg e Zn estão ganhando importância devido às vantagens que elas oferecem, em comparação com as tradicionais (AISI316L, L605), sendo a capacidade, de se degradarem a principal caracteristica. A escolha do eletropolimento, como técnica de modificação de superfície, deve-se a sua capacidade em polir o material tornando o seu relevo mais homogêneo, garantindo um pré-tratamento adequado ao material em diversas aplicações, como por exemplo o tratamento com o plasma. Um dos grandes diferenciais desta técnica é que pode ser utilizada em materiais com geometria complexa. Foram realizados testes utilizando um grupo de 4 soluções presentes na literatura e analisados os seus efeitos em amostras de ferro puro. Com os resultados obtidos pelas análises de Microscopia Óptica, Microscópio de Força Atômica e Ângulo de Contato foi possível verificar que a solução 2C obteve o eletropolimento mais efetivo, apresentando assim as características desejadas.

Oct 30, 2017

Computer applications in mine 'production' planning and control are concerned with the here and now. In production planning and control we are dealing with tactics as opposed to strategy. Our objective is to make the best of the situation in the short term, i.e., in a relatively fixed environment with relatively fixed plant, equipment, and labor. Environmental factors include not only the geology of the deposit but also market factors (such as price) and governmental constraints and regulations. Mine production planning systems are applied at the interface between concept and execution. Mine production control systems are applied at the interface between execution and revised operating practices or a revised concept. Fig. 1 shows the information flow that takes place regardless of whether the planning and control systems are manual or automatic. The feedback that results depends on the feedback mechanism that has been established, and this feedback can be enhanced by careful systems analysis and design. Chronologically, production planning and control activities support the last in the series of line functions that are ordinarily performed by mining companies. The first of these is exploration, the second is evaluation and development, and the third and final function is production.

Jan 1, 1979

By Qingwen Dai

The Marangoni effect is an important phenomenon where a surface tension gradient drives liquid towards high surface tension regions. Temperature gradient, evaporation, disparity of viscosity, and surface roughness and topography are all significant factors that can affect this thermo-capillary migration. The purpose of this study was to investigate the influence of micro-groove patterns on the migration of paraffin oil, and obtain a well-designed texture of micro-grooves to prevent the thermo-capillary migration. Patterns of micro-grooves with differing orientations and geometric parameters were fabricated on the surface of SUS 316 stainless steel substrates. Experiments on the migration behavior with different viscosities of paraffin oils were carried out various temperature gradients. The experimental phenomena indicated that the surface with the micro-grooves perpendicular or parallel to the temperature gradient have a strong impact on the migration performance of paraffin oil. Micro-grooves perpendicular to the temperature gradient exhibited extraordinary slower migration velocity than that of the parallel one. Width and depth of micro-grooves had an obvious influence on the behavior of temperature-driven migration and detail discussions on the effects of these geometric parameters were carried out.

Jul 31, 2018

By F. X. McCawley

The Bureau of Mines, in pursuing its goal of extending the life span of strategic materials, conducted field corrosion studies at the East Mesa Known Geothermal Resources Area (KGRA) in the Imperial Valley, Calif., to determine the optimum materials of construction for use in geothermal mineral energy resource recovery plants. These studies included characterization of geothermal environments and in situ corrosion testing. The corrosion resistance of 10 alloys exposed to 5 brine and steam process environments was evaluated using the low-salinity, high-temperature brine from geothermal well Mesa 6-1. Of these alloys, Hastelloy C-276, Hastelloy S, Incone1 625, titanium-2nickel, and 316 L stainless steel had excellent resistance to corrosion in all of the process environments; E-Brite 26-1 and 430 stainless steel had fair resistance. Although general corrosion rates for 4130 steel and 1020 carbon steel were substantially higher than those of the other iron-base alloys, these two alloys could prove useful in low-salinity process environments because of their low cost. Aluminum alloy 5005 was the least corrosion resistant alloy and pitted severely. Scales formed on all of the alloys in every process environment. Calcite, aragonite, and an amorphous silicate were the major components of the scales.

Jan 1, 1980

By Gibson J.

Further discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 3rd June 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.72-84, included a written contribution by Parfitt I.C. and the author's written replies to this and previous discussion

Dec 1, 1916

By Luara da Costa Morais

O objetivo deste trabalho é avaliar a influência da temperatura de recozimento intercritíco na microestrutura e nas propriedades de um aço dual-phase. Para isto, amostras do aço em estudo foram recozidas intercriticamente a temperaturas entre 720 e 740°C. A quantificação da martensita foi realizada por estereologia quantitativa sobre imagens obtidas por sinal de elétrons secundários. Ensaios de tração e de estampabilidade foram realizados no material tratado e na condição de partida. Os resultados da quantificação mostraram aumento na fração de martensita com o aumento da temperatura de tratamento. Para o estudo da influência da microestrutura no comportamento mecânico, foi relacionada a fração de martensita com as propriedades mecânicas obtidas nos ensaios de tração e estampabilidade. As amostras recozidas intercriticamente apresentaram aumento nos limites de resistência e escoamento e diminuição dos alongamentos, total e uniforme, com o aumento da fração de martensita. A amostra de partida apresentou frações de martensita similares às observadas para a tratada a 740°C, entretanto com valores de resistência e escoamento inferiores e alongamento superior, sugerindo influência da morfologia nas respostas mecânicas do material. O material como recebido apresentou a melhor combinação entre resistência, alongamento e estampabilidade indicando que esta condição é mais indicada para o setor automotivo.

Aug 8, 2018

By Willy Ank de Morais, Márcio de Morais Tavares, Mateus Araújo e Silva, Érika Elis Kuo, Cícero Lopes de Souza

Estruturas de aço são utilizadas em diversas aplicações na construção civil, com vantagens relativas a outros tipos de construções, tais como leveza e rapidez na execução da obra. Porém um dos maiores problemas neste tipo de sistema construtivo é a corrosão atmosférica a que estará sujeita o aço estrutural utilizado. Com o objetivo de se avaliar a resistência à corrosão atmosférica, neste trabalho, foram construídos painéis expositores, conforme a NBR 6209, para manter corpos de prova de aço estrutural comum e patinável, por um período inicial de setenta dias em dois locais distintos, categorizados com de agressividade ambiental I e III, respectivamente interior e litoral do estado de São Paulo. Superficialmente o processo de degradação foi nitidamente diferenciado, com o mesmo resultado sendo apontado pela alteração da massa das amostras, que se elevou durante a exposição ao ambiente de agressividade III, já que os produtos de corrosão formados não se desprenderam no curto período de tempo do teste. Mesmo considerado que a norma estipula um tempo mínimo de dois anos de duração para o ensaio, que ainda está em andamento, o presente estudo aponta a necessidade de adotar mecanismos de proteção contra a corrosão muito mais severos nas regiões litorâneas.

Mar 1, 2019

By L. M. Kocher, J. R. Heberger, J. P. Pollard, M. F. Nasarwanji

Injuries associated with hands and fingers are highly prevalent in mining and identifying factors associated with these injuries are critical in developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011–2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53%) followed by bone fractures/chips (26%). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals (pipe, wire, guards) and hand tools as the primary sources of hand and finger injury. Although information on glove use was limited, leather gloves were most often worn when an injury occurred. When worn, gloves were found to contribute to 20% of the injuries, indicating their potential to protect the hands, but also potentially put the hands at risk. Further research is necessary to determine performance requirements for gloves used in mining operations, specifically those offering cut and puncture resistance.

Mar 2, 2022

GENTLEMEN Herewith are transmitted reports from the Treasurer and of the principal standing committees of the Institute. To these special reports members are referred for details as to the year's work. Despite the unfavorable business conditions obtaining throughout the year, the Institute was able to carry on its various activities without curtailment and without drawing on the surplus accumulated through previous years. In fact, small additions were made to the Life, Member¬ship and various other funds. It is highly desirable that such additions should continue to be made, especially to the Life Membership fund, for reasons reported last year. At present, money must be used from current receipts in order to enable the Institute to fulfill its obligations to those who on joining the organization commuted their dues by a single payment. In addition, with the passage of years the number increases of those who have paid dues forty years or more and who, by reason of age or dis¬ability, are unable longer to practise their profession. These men have supported the Institute through their active professional life and it would be a pity to lose them as members through resignation or for failure to keep up their dues. In accordance with the By-laws the Board has authority to advance such members, on application, to the Honor Roll of Senior Members and to relieve them from further payment of dues. It has been the policy of the Board to do this liberally, but to keep up this, as well as to meet other obligations, it is necessary for money to be provided. It has been estimated by the Treasurer that nearly $50,000 additional should be placed in the Life Membership fund as soon as possi¬ble to meet these obligations without using current income and to that end it is necessary, not only to avoid running behind currently but to earn, if possible, some surplus each year. The small amount transferred to the Life Membership fund from surplus this year was, as a matter of fact, made possible by certain members paying personally bills that were properly chargeable to the Treasury. Such generosity is common among those active in Institute work and probably no year would have closed with a surplus except for it.

Jan 1, 1923