Search Documents

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

By Robert Hopler

THIS paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the headingand-bench system. Much depends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading.

Jan 1, 2010

By W. A. Cole

This report covers the preliminary phase of an investigation of clays, shales, and certain rocks in Wisconsin to determine the feasibility of processing lightweight aggregate in the State. The study was extended to include rotary-kiln testing of a limited number of shale samples, and to an appraisal of the Maquoketa shale resources in eastern Wisconsin. A total of 45 samples of clays, shales, and other argillaceous rocks of Wisconsin were tested. The lower Maquoketa shale is the only material found to date that offers possibilities as a source of material that can be processed in a rotary kiln for lightweight aggregate. Bedrock occurrences of the Maquoketa shale are found in the eastern and southwestern parts of the State. The populous southeastern region of Wisconsin presents a large potential marketing area for lightweight aggregate. For this reason special study was directed to the Maquoketa shale in the eastern district.

Jan 1, 1961

By S. Abe

An extensive study has been carried out to determine the true cause of floating slimes precipitation which sometimes occurs and badly affects the quality of copper cathodes. Soluhilities of floating slime compounds systematically measured for the ternary system As-Sb-Ri added solely or in combination with conventional copper electrolyte (63°C) and bench scale electrorefining experiments done by varying electrolyte composition, have shown conclusively that the level of Sb(V) ions plays a substantial role in the precipitation mechanism. It was, therefore, speculated that controlling the level of the less soluble S b ( V ) ions below a certain critical level should result in a complete elimination of the undesirable precipitation. This can be easily achieved, for instance, by the addition of a reducing agent such as SO2 gas and the simultaneous employment of a certain type of cheating agent that effectively removes excessive Sb and Bi from the contaminated electrolyte. Long-term pilot testing conducted in line with the above speculation has confirmed the SO2/chelating resin scheme to be industrially very attractive and feasible.

Jan 1, 1987

By T. C. Vogt

The past history of uranium production has been dominated by strip and shaft mining methods, but recently in-situ leaching has emerged as a viable alternative for uranium recovery. (1-8) Mobil was the first company to start in-situ uranium leaching in New Mexico. Mobil's Crownpoint project areas are in Mdinley County and are part of the Grants Mineral Belt. The major uranium deposits in this area occur in the Westwater Canyon Member of the Jurassic Morrison Formation. (9-11) The ore depth at the Crownpoint project is about 2000 ft. In an earlier paper we discussed the uranium mineralogy of an areally broad sampling of Crown- point ore. (12) The organic carbonaceous material often associated with the coffinite ore was characterized in some detail. The organic material appeared to be a very mature, coaly-type kerogen derived from plant components. This result was consistent with other studies on such carbonaceous material. (13-15)

Jan 1, 1981

By Scott Rodibaugh

El presente trabajo describe las aplicaciones representativas de la PPC (pressure-powered centrifugue) en minería, diseño básico, función y la experiencia de aplicación de OEM de motores. Asimismo se detallará ejemplos de desempeño de campo de la PPC como experiencias en un sistema hidráulico de camión minero, un motor diésel de camión minero y una trituradora de mineral que lleva el circuito de lubricación. De otro lado, se abordan los métodos de análisis de laboratorio para detectar los rasgos clave del fluido y evaluar la condición del contaminante.

Feb 1, 2017

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (CFR) Com¬mittee of the Coordinating Research Council (CFC) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36. 4/ Further re¬ports were issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941.4/ No reports were made on motor gasolines sold during the winter of l941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed. The present report presents analytical data for 3,011 samples, representing the products of 113 companies. Most of the samples represented in this report were obtained during July and August 1946. As in previous surveys the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gasoline are not considered adequate to represent this type of motor fuel, data for the analyses have not been averaged, but the individual items are tabulated. The number of samples, items, and brands comprising each group is as follows: Regular-price, 1,585 samples, 311 items, and 99 -brands; premium-price, 1,422 samples, 280 items, and 94 brands; third-grade, 4 samples, 4 items, and 4 brands. The meaning of these terms as used in the survey is as follows:"

Dec 1, 1946

By V Lishchuk, C Lund

"Geometallurgy aims to improve resource efficiency by creating a spatial model of an orebody in order to forecast ore processing behaviour. This enables calculation of the economic value of each ore block and the use of this information for production optimisation and hence an improved economic return. Modelling uses different approaches to link geological information with mineral processing: traditional approach uses chemical elements; proxy approach – small-scale geometallurgical tests; and mineralogical approach – minerals.A geometallurgical model is obtained during execution of a geometallurgical program encompassing the entire value chain of ore processing. Available methods for establishing a geometallurgical model are in many cases limited and not yet comprehensively validated. Some of the limitations include: sampling density, assaying methods and quality, forecast accuracy block model content, geostatistical solutions for non-additive components, blending and assessment of positive impact of geometallurgy on the project. Synthetic ore models combined with process simulations and production scheduling, based on strong case studies, present a viable way to address these shortcomings. Such synthetic ore models will have realistic elemental and mineral distribution, textural attributes and 3D variability for input into the design of an appropriate geometallurgical program.A synthetic orebody was created for an apatite-bearing iron deposit. Variability in modal mineralogy was described by geostatistical parameters combined by a set of linear and trigonometric functions. The generated synthetic deposit model was used to develop a mine production plan to generate a simulated process feed. The process feed had detailed information required for beneficiation process simulation: modal mineralogy, chemical composition of minerals, grain size and specific gravity. The synthetic system was used to measure benefits that a geometallurgical program developed for real cases could provide, compared to production where only head grade is optimised. These include a reliable sampling strategy and confidence in the feed-quality forecast for economic evaluation.CITATION:Lishchuk, V, Lund, C and Lamberg, P, 2016. Development of a Synthetic Ore Deposit Model for Geometallurgy, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 275–286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By F. Chiesa

The permanent mould process, which is a favoured process for producing premium quality aluminium casting, is rarely used to produce magnesium alloy parts. This may be attributed different factors such as: the reservation with which the automotive industry considers using magnesium in structural castings; also the relative hot shortness of most magnesium alloys when compared to aluminium A356/357 is another factor. A third reason stems from the fact that the "heat content" of magnesium is much less than that of aluminium, resulting in the difficulty, for a relatively slow process such as permanent mould (versus pressure die casting), to reach a mould dynamic equilibrium temperature sufficiently high to avoid premature freezing and misruns. The present work will address this problem by carrying out controlled cycling of a laboratory mould, poured with aluminium and magnesium alloys. The influence of insulation of the mould and artificial electric heating on the run-in mould temperature will be determined experimentally. A thermal model will be sought for these thermal devices that will allow to predict the thermal behaviour of moulds of different geometry before a single casting is poured. The model will be tested on an industrial casting in a workshop environment.

Jan 1, 2006

Energy benchmarking is widely applied across industries to determine the potential to improve energy performance. Unlike the many technologies for which energy benchmarks and efficiency rating systems are already in maturity, benchmarking of mining processes is still in its infancy. Benchmarking energy usage in mining operations, where energy costs are high and represent a significant portion of overall operating expenses, is challenging due to the uniqueness of each mining operation. Mines vary in terms of geology, geographic setting, ore body geometry, mineralogy which impact the mining method, material handling, processing and waste management. In order to gauge the opportunity for reducing the energy intensity of individual operations and also to compare the energy performance of operations on a global scale, the deployment of new benchmarking methodologies, models and frameworks is necessary. As a step towards the establishment of an accurate framework for benchmarking the energy consumption of mining operations, comminution, one of the more energy intensive mining sub-processes, was selected as the focus of a new energy benchmarking method. The methodologies and processes used to onset fragmentation in a rock mass to the crushing or grinding of rock to a size that is suitable for economic extraction are predominantly dependent on the ore properties. For this reason, site specific factors, such as the size reduction requirements and ore hardness were included in an energy benchmark model so that the energy performance of comminution processes at different operations could be normalized and compared on a global scale. Single particle compression breakage has been identified by several prominent researchers in the field of comminution as the upper limit of energy utilization in size reduction processes. For this reason single particle compression breakage was proposed as the basis of a work index for ores to be used as an input for the benchmark model. Overall, the new method showed that the energy benchmark for mineral comminution can be normalized and subsequently compared for a range of mining operations once the ore hardness has been appropriately characterized.

Aug 1, 2013

By L. M. Pidgeon

MAGNESIUM metal, with a specific gravity of 1.73, is two-thirds the weight of aluminium and one-quarter that of steel. It is the lightest metal which is stable in the atmosphere. Before the war it had begun, though somewhat slowly, to take a place among the established metals. In 1939, magnesium production on this continent amounted to some 3,000 tons per annum and was confined to one company. At that time, Germany produced perhaps 20,000 tons. The advent of war, however, increased the demand to fantastic heights and introduced production problems of unprecedented magnitude. By the end of 1943, North American production is expected to reach 300,000 tons per annum (1), an increase of one hundredfold. Such a rate of expansion has not been witnessed previously in the history of metallurgy. It has given the metallurgist an opportunity to try new production methods and to learn in a short time what might otherwise have taken many years. The metallurgy of magnesium is still in its formative years and at this time widely different production methods are in operation side by side. This paper will discuss these methods in so far as information is available for publication at this time. A general description of the new Canadian industry will be included.

Jan 1, 1944

By E. Asselin, G. K. Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe(II)Fe( III)H2SO4 solution at 90 °C and 110 °C. Results from the calculation of speciation in the above solution reveal that, at both 90 °C and 110 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller VALUES (for the reversible potential of the ferric/ferrous couple. Exchange current densities of the ferric/ferrous couple were obtained and are on the order of 106 10 5 A/cm2 a t 9 0 °C and 1 07 10 6 A/cm2 at 110 °C, respectively. The Tafel slopes from the CPP method are higher than those from the CPC method at both 90 °C and 110 °C. The transfer coefficients were about 0.360.59 at 90 °C and 0.370.65 at 110 °C. Based on the exchange current densities obtained, the rate constant kc was calculated. It was found that kc at 90 °C was slightly larger than at 110 °C, especially for the results obtained by the CPC method. The average rate constants are 862.17 cm/s for CPC and 65.30 cm/s for CPP at 90 °C, and 477.69 cm/s for CPC and 63.53 cm/s for CPP at 110 °C for nominal Fe3+/Fe2+ ratios ranging from 1:1 to 1000:1. INTRODUCTIONChalcopyrite is one of the most abundant copper-bearing minerals, accounting for approximately 70% of the world’s known copper reserves (Wang, 2005). Most of the currently proposed leaching processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale, such as Activox (U.S. 5,232,491, 1993), Nenatech (U.S. 5,993,635, 1999), Dynatec (U.S. 5,730,776, 1998), AAC/UBC (U.S. 6,503,293, 2003), Total Pressure Oxidation (U.S. 5,698,170, 1997), CESL (U.S. 5,874,055, 1999) and Galvanox (U.S. 7,846,233, 2010).To date, much effort has been devoted to understanding the kinetics and mechanisms of the oxidative processes (Biegler & Horne, 1985; Córdoba, Muñoz, Blázquez, González, & Ballester, 2008, 2009; Ghahremaninezhad, Asselin, & Dixon, 2010; Hirato, Majima, & Awakura, 1987; Hiroyoshi, Kuroiwa, Miki, Tsunekawa, & Hirajima, 2004; Warren, Wadsworth, & El-raghy, 1982) or the cathode reduction reactions of chalcopyrite itself (Arce & González, 2002; Biegler & Swift, 1976; Biegler, 1977; Nava, González, Leinen, & Ramos-Barrado, 2008), by chemical or electrochemical methods. However, as the most important cathodic processes in chalcopyrite leaching systems, the cathodic reductions of ferric ions or dissolved oxygen are worth measuring due to their effects on the overall leaching rate, as predicted by mixed potential theory."

Jan 1, 2012

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different field and regions as made by the Bureau of Mines Hempel method of analysis.4/ Several of these reports include analyses off crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937

By Charles F. Weber

Premature blasts of charges of explosives have caused many deaths in anthracite mines, and the causes of many of the blasts were not determined satisfactorily. Investigators often found fairly high potential differences between such metallic objects as rails, pipes, conveyor lines, or sheet-iron chutes in the working place where an accident had occurred. At one mine where a premature blast occurred in a rock tunnel, one workman was killed and two others were injured, and several days later a potential difference large enough to explode an electric squib was detected between the compressed-air pipe and the track rail; the voltage fluctuated and appeared to change with the movement of a locomotive. At another mine, a. workman was killed when a primed cartridge that he was about to load in a blast hole exploded in his hand. During the investigation, a potential difference was found between the conveyor line and the sheet-iron chute. During a 5-year Period, 61 fatalities and 771 nonfatal injuries were caused by explosives accidents in anthracite mines, and one of the chief causes of these accidents was premature blasts.

Jan 1, 1950

By Fernández H. Carlos

Debido que el subproducto en la etapa de lixiviación de las calcinas de zinc, alcanza un 18% de plomo y 40% de plata en la refinería de Cajamarquilla, es necesario la recuperación de sus elementos valiosos a través de un procedimiento hidrometalúrgico donde se obtengan extracciones en plomo y plata del orden de 85% respectivamente. En este sentido, el texto señala la solubilidad del plomo y la plata en una solución con excesos de iones cloruros y así someter al residuo a una lixiviación ácido clorurante de altas temperaturas y con presencia de un agente oxidante. Una vez obtenida la solución, se divide el plomo y la plata por cementaciones sucesivas con polvo de zinc. Finalmente, se determina la factibilidad del procedimiento para la extracción de los elementos valiosos del residuo y se disminuye los costos de la refinación del zinc.

Nov 8, 1984

By David McMullen

Radiation plays a critical role in the thermal behaviour of hydrometallurgical process equipment. This effect is particularly important when designing refractory lined equipment used in pressure leach/oxidation processes. In order to simplify this non-linear mode of heat transfer, the effects of radiation had previously been incorporated in an equivalent convective film coefficient in finite element methods (FEM). This prior method omits the effects of radiosity, a critical aspect of radiation heat transfer, which affects the design of refractory lining systems in autoclave vessels. Given that 60% of the heat loss in actual plant practice of an autoclave is due to radiation, reliability in the FEM is therefore impacted. This study validates the use of radiosity in FEM through thermal loading using a combination of simple geometries to be applied to complex environments such as vessel nozzle clusters. The added benefits of using a radiosity load includes an increase in confidence in thermal distribution results, greater accuracy in determining appropriate refractory lining systems, weld overlay sizing, and increased accuracy in structural analysis.

Jan 1, 2014

By Jorge Acuña de la Fuente

El presente texto describe el estado actual de la fabricación del coque y del carbón como uno de los elementos químicos y fuentes de energía más importantes que intervienen en la industria siderúrgica peruana. El carbón se explota en la mayor parte de las naciones del globo. Sin embargo, una cantidad apreciable de países productores no logra satisfacer sus propias necesidades y depende en mayor o menor escaia de la importación. Con el fin de garantizar los suministros de importación, se ha generalizado la práctica de celebrar contratos a largo plazo, iniciada por los grandes países consumidores. De otro lado, el coque, es el producto residual de la destilación seca de carbones bituminosos, cuyo elevado costo ha orientado los estudios técnico-económicos sobre su elaboración hacia dos objetivos fundamentales: en primer lugar, la optimización del proceso clásico de coquificación, al desarrollar paraielamente nuevas técnicas del carbonización, y por otra parte, la variación de las fundiciones en el alto horno en pro de un menor consumo específico de coque, ya sea por reemplazo parcial de éste por otros elementos reductores, o nuevos artificios de operación.

Jul 1, 1979

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

By E. P. Olberg, A. Yu. Chikin, S. V. Petrov, M. P. Belykh, N. L. Belkova

"Bacteria that grow in autochtonous communities of gold heap leaching (HL) wastes are adapted to high concentrations of contaminants and environmental conditions. An example of a mine in the Sakha (Yakutia) Republic showed that the bacterial factor had a significant influence on cyanide breakdown and copper and nickel removal in the conditions of HL ore pile zoning compared to chemical oxidation. The diversity of bacterial communities growing in natural and simulated conditions of a HL ore pile was determined for the purpose of the study. The identified bacterial communities included genus Achromobacter and Serratia, which were found to be adapted to a wide range of temperature and can be considered as potential microorganisms for detoxification of gold HL wastes. INTRODUCTION Technologies and systems of passive treatment are of a special interest in relation to solving environmental problems of gold HL wastes detoxification, when neutralization time is not considered as a limitation (Alvarez et al. 2005). Passive treatment methods are based on reagentless spontaneous breakdown of cyanide caused by natural factors, including activity of autochthonous bacterial communities. Implementation of a reagentless biodetoxification technology for mature HL operations provides reduction of environmental impact on industrial site locations and substantial economic benefits compared to conventional chemical processes of neutralization that prevail in the Russian Federation territory. Passive treatment of cyanide-containing wastes was investigated by M. Botz, T. Mudder, S.V. Petrov, L. Simovic, A. Smith, C.A. Young etc. However, the bacterial factor (autochtonous bacterial communities) role in this process is practically unexplored. Thus, the aims of the study included the investigation of a bacterial factor influence on passive treatment of gold HL wastes and the identification of functional groups of bacteria involved in passive treatment."

Jan 1, 2018

By Paul M. Tyler

The colony of French Guiana ( or Cayenne ) is administered by a governor , assisted by a privy council of five members . A council - general of 16 members is elected by French citizens resident in Guiana, and the colony is represented 3 in the French parliament by one deputy . The area is about 34,740 square miles . French Guiana is the largest gold producer of the French colonies , producing nearly $ 1,000,000 worth annually . Considerable prospecting has been done on the bauxite deposits , which are extensive . Copper , iron , lead , and 4 mercury deposits are also reported . In 1931 , 10,000 prospectors for gold were reported as working . The French Government is taking an active interest and has sent a committee of mining experts to explore the region ; no permits are to be issued to individual prospectors while the committee is in the colony . Plans for development of mining industry include consideration of 4,500 convicts and 2,500 natives already in the colony and available for labor .

Apr 1, 1933