Search Documents

By Arthur E. Bruszak, Marcel Vanpée

In many practical combustion systems ignition may occur through contact with hot burned gases . Such a process plays a vital role in flame stabilization on bluff bodies . It is also of importance in the ignition of firedamp by the hot spent gases of explosives used in mines . Also , in the communication of flames through narrow channels , a problem of practical importance in flameproofing electrical equipment , the propagation of the flame is essentially a reignition process in which hot burned gases are the agent of ignition . In the actual ignition problem a great variety of conditions may be visualized . Ignition may occur where pockets of hot gases are surrounded by cold explosive mixtures or where pockets of cold mixture may be surrounded by hot gases . Alternately , a flowing stream of combustible mixture may be initially in contact with another stream of hot combustion products , or a jet of hot gases may flow into a cold quiescent mixture ; the jet may be laminar or turbulent , continuous or discontinuous . The hot gas may also consist of the oxidant ( air for instance ) and the cold combustible pure fuel . This study by the Bureau of Mines is concerned only with ignition produced by a continuous jet of gas ( hot ) flowing into a practically quiescent cold mix- The investigation of ignition by bursts of hot gases or by turbulent jets is outside the scope of this report , and work performed on this phase of the problem has been published elsewhere

Jan 1, 1963

By L. G. Morrell

Introduction A Self-Dumping cage which combines the features of a small skip and a cage has been used in a vertical winze between the 2,000 and 2,500 levels at the Coniaurum mine for the past three years, during which time its success has been demonstrated by uninterrupted service and low maintenance charges. lt was designed by John Reddington, mine manager, and was built under his supervision in the Coniaurum mine shops. Being new in many of its operating features, a small-scale model was made and tried before the final construction was undertaken. The mechanical performance of the model suggested a few minor changes that were incorporated in the final drawings. During its three years of use, the automatic dumping device has saved the expense of deck-handling of the cars. This actually represents a gross economy of something over four times the cost of construction and installation, which totalled $1,325. The cage, empty, weighs 2,200 pounds, of which 500 pounds represents the weight of the dumping accessory and necessarily heavier construction. Besides a considerable financial saving, the time saved in unloading increases the daily hoisting capacity of the winze. In raising ore from the 2,500 level, five minutes are required for a complete trip. Allowing one minute for the alternative of decking, we believe that the automatic dumping has increased the capacity of the winze hoist nearly 20 percent.

Jan 1, 1933

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

"Dialkyl dithiophosphinates are a unique class of collectors used in the flotation processing of Cu- Au, complex polymetallic, and precious metal ores. They are known to exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive HSE profile. Historically, for most reagents used in flotation, practical methods of chemical usage have preceded detailed scientific understanding of how they work; this applies also to dithiophosphinates. Recently, however, the research community has shown significant interest in this chemistry, and numerous studies have been conducted to understand the fundamentals of interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized by drawing on concepts and insights from coordination chemistry. A comparison between the interactions of dithiophosphinates and dithiophosphate analogues with various minerals and metals is also made throughout. We believe that such a critical analysis/overview will be invaluable in identifying gaps in knowledge regarding this important set of compounds, which in turn may provide a basis for the design of studies that can advance understanding of their flotation performance. INTRODUCTIONDialkyl dithiophosphinates are an important member of the class of thiophosphorus compounds that are widely used in flotation beneficiation of base metal sulfide and precious metals ores. Ore flotation studies and plant practice experience have demonstrated their unique properties compared to the traditionally used sulfide collectors such as dialkyl dithiophosphates (their closest analogues) and xanthates. The predominant dialkyl dithiophosphinate used in the industry today is sodium diisobutyl dithiophosphinate (a.k.a. DIBDTPi; AEROPHINE® 3418A1 introduced by American Cyanamid in the late 1970s; Figure 1). The widest application of AEROPHINE 3418A is found in complex polymetallic ores of Cu-Pb-Zn-Ag, Pb-Zn-Ag, and Cu-Zn where it has demonstrated improved recoveries (and flotation rates) of sulfide minerals of Cu, Pb and Ag and selectivity against sphalerite, iron sulfides, and penalty elements (Mingione, 1991). More recently, it has also been used as a collector in the processing of Cu, Cu-Ni, and Ni ores (Guitard et al., 2015) and Cu-Au ores (Dunne, 2005). In general, it is considered to possess the collecting power of xanthates together with the selectivity (against pyrite) of dithiophosphates (Hope et al., 2003a, 2003b), while requiring lower dosages than those reagents (Guitard et al., 2015). AEROPHINE® 3418A has also found an important place in several targeted formulations to improve flotation performance. Other benefits of this reagent include higher flotation rates, having a better HSE (health, safety and environmental) profile2 compared to xanthate, and exhibiting resistance to hydrolysis and oxidation (Guitard et al., 2015). Compared to diisobutyl dithiophosphate (DIBDTP), which is known to contribute significantly to frothing (often leading to over-frothing), AEROPHINE® 3418A is observed to be froth neutral (i.e. it does not alter the existing froth characteristics). As is the case for other flotation reagents, the design and application of AEROPHINE® 3418A has preceded understanding of its behavior at a fundamental level. Recently, there have been numerous fundamental and application studies designed to develop a better understanding of its interaction with sulfide minerals and precious metals. This should help in optimizing its application in flotation and provide a basis to better rationalize its unique selectivity and activity characteristics. Past studies on the interacti"

Jan 1, 2016

By Camilo Quintero, Frank Cesario, John Kinnear, Brian Boye

In this paper, an innovative approach was adopted to automatically calculate the effects of tunnel induced settlement on buildings and utilities. The approach resulted in increased output quality, consistency, reduced time, cost savings and a greater ability to respond quickly to design changes. The techniques described have been applied to the Fairbank Silverthorn Storm Trunk Sewer System project, located within the City of Toronto. The automation allowed a very large area of topography, tunnels (6 km), buildings (9000) and utilities (over 1000) to be rapidly evaluated. Visualization of the settlements and impacts also allowed the project design team to optimize the system design to mitigate the settlement impacts.

Jun 13, 2021

By Cuppam Dasarathy

The incidence of liquid inzmiscibility in binar)) indium alloys has been theoretically analyzed on the basis of the Hildebrand-Alott equation. Bedictions of miscibility or otherwise Imve in general been found to agree with those phase diagrams that are already publislzed in the literature. Out of a total of 27 systems, where either the complete phase diagrams are published or liquid immiscible behavior is reported, the Predictions agree with the experimental data in 25 systems, the exceptions being the Te-In and Ni-In systems. According to the equation, liquid immiscibility is also indicated in the binary alloys of indium with K, Rb, Cs, Na, Sr, Ba, Ti, Zr, V. Nb(Cb), Ta, W, U, Re, Ru, Rh, Os, and Ir. RECENT investigations by the author have shown that indium when alloyed with iron, chromium, and cobalt shows liquid immiscible behavior.1"3 The Fe-In phase diagram shows a wide range of compositions where the liquids are immiscible.4,5 No intermediate phases are present in this system. No precise information is available about the extent of liquid immiscibility in the Co-In system. However, it is certain that there is a range of compositions where the liquids are immiscible and that there are two or three intermediate phases,376 in the system. Liquid immiscibility is also strongly indicated in the Cr-In system and no evidence was obtained in the brief investigation to indicate the presence of intermediate Cr-In phases.2 The present paper deals with a theoretical analysis of binary alloys of indium with certain elements of the periodic table and indicates the systems where liquid immiscibility may be expected. The incidence of liquid immiscibility in binary systems has been theoretically examined by many workers and many excellent papers are available on the subject. In this paper, the alloy systems are examined on the basis of the more recent ideas proposed by Mott.7,8 It has been claimed8 that the Mott parameter predicts the incidence of miscibility or otherwise with reasonable accuracy and consistency. BACKGROUND TO MOTT&apos;S APPROACH Hildebrand applied his immiscibility rule for non-polar liquids to various alloy systems.9 The basis of this rule is that the equation for the excess free energy of formation of a liquid solution is rather similar to the theoretical expression for the energy of mixing of a regular solution. He postulated that when the heat of mixing is sufficiently high, separation into liquid phases will occur and the condition for complete CUPPAM DASARATHY is at the Research Centre, British Steel Corporation, (South Wales Group), Port Talbot, Glamorgan, Great Britain. Manuscript submitted March 12, 1969. IMD miscibility was shown as where VA and VB were the atomic volumes of the components A and B, and ?EV the energy of vaporization of the component. The term (?EVA/VA)1/2 was regarded as a measure of the binding energy of the component A and was called the L&apos;solubility parameter" 8A. On this basis immiscibility occurs when 1/2(VA+VB)(bA-bBf > 2RT [2] Apparently, however, there were several inconsistencies in that according to Eq. [2] several systems known to be miscible in the liquid state were predicted as immiscible. MOTT&apos;S ANALYSIS ~ott&apos;" regards that the reason for the inconsistencies arising out of Hildebrand&apos;s equation was largely due to the electrochemical attraction between the two elements, not being considered. Hence, Eqs. [I] and [2] were modified by taking into account the electro-negativities of the two elements XA and XB, and Mott arrived at an equation for immiscibility, i(VA + VB)(6A - aB)2 - 23,Q60n(XA - XBf > 2RT [3j which can be written as i **&£*&* >&apos;*°™- &apos;• HI T being the melting point of the more refractory component of the system. In Eq. [4], the numerator was called the Hildebrand term, the denominator, the electronegativity term, and their ratio, the Mott number. Mott observed that if the Mott number of a given binary system was greater than the maximum number of Pauling bonds which the two metals could form, then liquid immiscibility could be expected. The maximum number of bonds formed by a given metal was considered to be directly related to the number of bonding electrons available, i.e., to its maximum valency. Since the valencies of the elements considered vary from 1 to 6, Mott assumed that if the ratio of the Hildebrand term to the electronegativity term was >6, then immiscibility could be expected. On the contrary, if the ratio is <1, the metals should be miscible. Further, the alloying behavior is not only influenced by the valencies of the two elements but also by the relative atomic sizes that influence the types of packing and hence the coordination number. Mott considers that on average the maximum number of near neighbors of unlike atoms is 6. Thus, on both valency and size factor considerations, Mott concludes that the maximum number of bonds&apos; possible in any system was 6, this being the upper limit of the Mott number for miscibility. In considering the alloying behavior of systems with Mott numbers between 1 and 6, Mott plotted the num-

Jan 1, 1970

By Stephen G. Wright

Jan 1, 1985

By M Norbert, D O’Connor

The mainline running tunnels for Legacy Way comprise two tunnel boring machine (TBM) driven tunnels. Both TBM drives commenced at the Launch Portal adjacent the Mt Coot-tha Road. Excessive surface settlement arising from tunnelling would have had a significant impact to the road infrastructure. The geological structure above the tunnel springline is a mixture of fill, residual soil and weak rock. Given the combination of low ground cover and weak ground materials, along with the use of an open face TBM, an oversize pipe umbrella system has been installed above the tunnels. This pipe umbrella system is similar to that commonly adopted in conventional mined excavation support in soft ground except that the steel pipes are substantially larger in geometry and filled with concrete. It is acknowledged that similar systems with oversize pipe umbrella have been adopted elsewhere in the world in other projects. These systems often comprise of a full arch formed by conjoining oversize steel pipes (in contact only). By aligning the pipes in contact, the arching behaviour of the steel pipe would have been enhanced. However, this poses a degree of construction difficulty due to excavation and installation method of the pipes. The Legacy Way pipe umbrella system only consists of a partial arch at the tunnel crown and each pipe is spaced approximately 1200 mm apart with 900 mm diameter pipe, leaving a gap of approximately 300 mm between pipes. A reinforced concrete portal block was used to support the exposed ends of the pipes.This paper reviews the design analysis, the recorded deflections from the pipe umbrellas and surface monitoring during TBM launch and revisits the analysis using the newly available RS3 program, from Rocscience for 3D analysis of geotechnical structures.CITATION:Norbert, M and O’Connor, D, 2014. Starting the journey – launching of the Legacy Way open face tunnel boring machines in mixed face ground conditions, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Jonisha P. Pollard, F. Nasarwanji, Lydia M. Kocher

This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1000 full-time employees, which is nearly double the rate of the next highest affected body part, the back.

Feb 24, 2022

By William Petruk

The development of automatic image analysers brought the application of image analysis into process mineralogy because the analysers can measure parameters more easily, quickly and accurately than by manual grain counting techniques, and can also collect data unobtainable by manual grain counting. Data from ore specimens and mill products are used to predict and to define the behaviour of minerals during processing. The analyses are generally performed on the basis of either surface areas or linear intercepts of grains in polished or thin sections, and the data are computer processed to give mineral quantities, liberations, size distributions, and characteristics of middling particles. For analysis, the minerals must be detectable and discriminatable from each other. An image editor is usually used when minerals are not easily discriminated. In addition BSE-8EM photographs have been used where the silicate minerals could not be discriminated from the mounting media. Methods of analysis, typical results, and their applications are discussed.

Jan 1, 1982

By P. Regan

Following the introduction of the Contilanod process over 10 years ago at Copper Range and IMI Refiners, significant changes and advances have been made to this pioneering anode production technique. A new radial flow metal feeding concept has been developed that allows a substantial increase in casting rates on the Hazelett® twin-belt caster. To cut the 45 mm thick continuous anode plate into shaped anodes at rates of 100 t/h or more, a filly moving hydraulic shear designed by Mannesmann Demag has replaced the slower speed plasma cutting torch. Details of the.new caster and shear are presented along with operating results from the new lines starting up in 1999 at the Gresik smelter/refinery in Indonesia and the completely revitalized Mansfelder Kupfer und Messing complex in Germany.

Jan 1, 1999

By J. D. McKay

The Bureau of Mines devised a column flotation technique using either fine or coarse bubbles and compared it with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a 44.7-pct-Cr203-grade rougher concentrate with 87-pct recovery, compared with 43.8- and 43.5-pct-Cr203-grade rougher concentrates with 85- and 77-pct recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse-and fine-bubble column flotation produced rougher concentrates containing approximately 41.5-pct-Cr203 with 95-pct recovery, exceeding conventional flotation which produced 35.6-pct-Cr203-grade concentrates with 87-pct recovery.

Jan 1, 1985

The Mineral Industry of Canada in 1951 Continuance of the remarkable, successive increases in the value -of Canada&apos;s mineral production, chief basis of the nation&apos;s post-war expansion, was one of the highlights of Canadian development in 1951, when, according to the preliminary estimate is-sued by the Dominion Bureau of Statistics and reported in the BULLETIN for February, 1952, mineral output for the year reached a new high of $1,228 millions. This marked an increase of 17.5 percent over the previous year, which was the first in which the billion dollar mark had been reached, and an increase of 143.7 per cent over 1946, when production was valued at approximately $503 millions. While higher prices for the principal base metals accounted for a large part of the 1951 increase, quantity gains were made by copper, nickel, zinc, asbestos. lead, cement, and strikingly important. by petroleum, the value of which exceeded for the first time that of coal production. Gold was an exception to the general trend, being lower in both quantity and value than in 1950. For the first time nickel .came within $9 millions of surpassing-gold as the leading mineral product. Metals and Fuels The value of all metals, estimated at $733 millions, was 18.7 per cent more than in the previous year. Nickel advanced 11 per cent in volume and 34 per cent in value. Copper was up 2.4 per cent in quantity and 21 per cent in value, zinc rose 6.6 per cent in quantity and 35 per cent in value, and although the volume of lead produced was lower by 8 per cent, its value increased by 17 per cent. The tonnage of iron ore was 31 per cent higher than in 1950.

Jan 1, 1952

By J. J. Pfeiffer, J. W. Myers, A. A. Orning

A study was made of the feasibility of using washery refuse in the manufacture of lightweight aggregate for building materials . Preliminary caking and burning tests showed that the refuse could be converted into lightweight aggregate but that refuse passing a No. 14 U.S. Standard screen could not be used without additional processing . The aggregate was prepared by pelletizing the refuse and burning out the carbonaceous material on a chain- grate in a refractory - lined furnace . A small stationary - grate furnace was used to study the process variables involved and establish optimum ignition and combustion conditions . Maximum ignition rates were obtained at air rates of approximately 200 lb per sq ft hr , but air rates of 450 or higher were required in the burnout period to obtain temperatures high enough to sinter the ash . The data obtained from this unit were used as a guide in the operation of the chain- grate furnace . In the chain - grate furnace , satisfactory results were obtained by using primary air rates of 200 lb per sq ft hr in the ignition zone and 500 lb per sq ft hr in the burnout zone . The ignition- zone air was preheated to 500 ° F , but the air for burnout was not preheated . A total of 2-1/2 tons of aggregate was prepared in this unit and made into experimental block . A commercial development based upon the results of this study yielded a product which met the ASTM specifications C 130-42 for lightweight aggregate , and blocks made from the aggregate were of good color , durable , and light - inweight .

Jan 1, 1964

By P. G. Carpenter, R. G. Nisle, F. W. Bubb

It is the purpose of this paper to describe an electrical computer which has been constructed to solve the equations for vapor-liquid equilibrium in multi-component systems. The instrument consists of seven component-computing units each with proper indicating means and power supplies. Each unit is a resistance network with a voltage matching servomechanism, and each provides an output voltage proportional to the mol-fractions for vapor and liquid phases. These voltages are summed and matched with a reference voltage to provide the solutions. Any reasonable number of such units may be put together to make a computer. The theory and operation of the computer is discussed. A number of applications and examples of computer results are given. The computer yields the over-all vapor or liquid fraction to a probable error of 0.002. An interpolation method is described which reduces the probable error to 0.0002. INTRODUCTION The process known as Flash Vaporization may be described as follows: A mixture of known composition of relatively volatile components is allowed to come to thermodynamic equilibrium at some given temperature and pressure by any path whatsoever. In general, a vapor and a liquid phase will be present at equilbrium. The problem is to determine the fractions of the mixture in the vapor and liquid phases, and to determine the mol fractions of the various components in each phase. The relations that exist between these various quantities at equilibrium are well known and will be given later. These equations are difficult to solve, yielding only to trial-and-error methods. The virtues of the analog computer are its speed and the automatic character of its calculations. The device is operated by turning a crank which varies the value of v, the total vapor fraction. This actuates a number of servomechanisms which perform automatically all computations. This computer facilitates the solution of such problems as (to mention a few] : Analysis of separator operation, studies of changes in composition of reservoir fluids with pressure decline, and analysis of natural gasoline plant operation. Examples of some of these problems are given in detail later. STATEMENT OF THE PROBLEM The essential equations are xm = 1+(km-l)v . . (1) Kmzm ym =------------------------. . (2) 1 + (Km-l)v ; n n S S xm= --------------------=1 1 + (Km-l)v m = 1 m=1 ......(3) n n S = S Km Zm =1 S ym 1 + (Km-1)v m=1 m = l ......(4) where ym = Vm/V = Mol fraction of m-th component in vapor phase. xm = Lm/L = Mol fraction of m-th component in liquid phase. Zm = Fm/F = Mol fraction of m-th component in mixture. KM = ym/xm = Equilibrium constant for m-th component at the given temperature and pressure. v = V/F = Mol fraction of vapor in the mixture. F = Total mols of a mixture of n components. V - Total mols of vapor in the mixture. L = Total mols of liquid in the mixture. Fm = Total mols of m-th component. Lm = Mols of m-th component in liquid phase. Vm = Mols of m-th component in vapor phase. Assuming the total mols of the mixture F and its composition (all the Fm) to be known — either from a quantitative analysis or from the amounts put together to make the mixture — the zm = Fm/F may be regarded as known quantities. From the given temperature and pressure of the mixture the K., are known (principally from experimental data). The primary problem is then: having given all the zm and Km to calculate v and all the fractions xm and ym. Having calculated these ratios, it is a simple matter to calculate V. L. Vm, Lm from their defining equations. SOLUTION OF THE PROBLEM Basic Computer Unit The computer consists of n units, each of which provides voltages xEo and YE, proportional to x and y as in

Jan 1, 1950

By R. V. Ramani, K. V. Raj, S. Bandopadhyay

The air flow problems in openpit mines are complex. Computational fluid dynamics (CFD) models can provide detailed information regarding air flow pattern, velocity distribution, temperature, and pollutant concentration in an enclosed domain of an openpit mine. A range of turbulent models can be selected with varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithms they use. As a result, predictions vary from model to model. This paper presents a study of pollutant transport in an actual openpit mine under a stable boundary layer. The objective was to test two turbulence models using similar geometry and the same input conditions and model constants. Measured data were used to compare the results of the two CFD models, namely, the kappa-epsilon (к-є) model and the Large Eddy Simulation model. Despite the complex synoptic situations, different meteorological input data and fast-changing conditions, the simulation results from both the models were in good agreement regarding the dispersion of pollutants.

Jan 1, 2015

By H. P. Hamlin, W. A. Grosh

Samples of clays , shales , and argillites from 21 locations were subjected to preliminary bench- scale tests for bloating properties , and several samples were tested for ceramic properties . Samples showing favorable bloating properties were further tested in a pilot - plant - scale rotary kiln . Physical characteristics and concrete -making properties of the bloated products were determined . The Decorah shale from one area made a suitable material for a lightweight aggregate ; however , the limestone layers in the formation must be eliminated or the resulting activated lime must be controlled by quenching .

Jan 1, 1963

By Alan D. Randolph

A size-continuous breakage kinetics model is postulated and supported with industrial grinding mill data. It is shown that the kinetics parameters include the effects of possible classification at the mill discharge. The estimated parameters were then used in the kinetics model to simulate the behavior of a grinding mill in open and closed circuit operation. While material transport and kinetics are equally important in open loop operation, heavy recycle in a closed circuit make a detailed material transport model for grinding unnecessary. In effect, the mill can be considered as backmixed. This suggests that more emphasis should be placed on modeling the classifier than the development of detailed material transport models for the grinding mill.

Jan 1, 1975

By Henry C. Meeves

The nonpegmatitic sources of beryllium in Arizona, Colorado, New Mexico, Utah, and four adjacent states investigated by the Bureau of Mines are described. The investigations included 155 properties from which over 6,200 rock samples were collected; more than 5,500 samples were analyzed by the nuclear beryllium-detection technique. Twenty-four of the properties examined had rock containing more than 0.10 percent BeO. Many of the beryllium determinations were made in the field with portable detection instruments by direct scanning of outcrops and by testing samples of rock brought to the instrument. The large domestic resources of low-grade nonpegmatitic beryllium ore in Utah, which were discovered by private enterprise and which respond favorably to small-scale treatment processes, may come into commercial use and thus reduce the dependence of the United States on imported beryl.

Jan 1, 1966

By P. Oliver

Rockburst conditions were first encountered at Inco&apos;s Sudbury area operations in the mid 1930&apos;s when mining advanced to below the 610 m (2000 ft.) horizon. Now, mining is being carried out at depths down to 2130 m (7000 ft.) at Inco&apos;a Creighton Mine. While rockburst potentials have increased with depth. improvements in mine planning, methods, support systems and developments in destressing have alleviated the condition to where it is less of a problem now than it was in the early years. Hang of the improvements were developed, of necessity. through observation and reasoning because these were the only tools available at the time. Now, we are making use of stress - measurements, numerical modelling and microseismic source location technology to - help further reduce rockburat hazards.

Jan 1, 1987

By F. V. Lenel

This discussion is concerned with the method of manufacturing, the design possibilities, and the properties of pole pieces for direct-current electric . motors and generators made from iron powder. In such applications as pole pieces, the electric and magnetic properties of the material are of major importance, therefore they are discussed somewhat more fully. However, the main advantage in making pole pieces from powders lies in the rapid and inexpensive method of manufacturing these pieces, and in the flexibility of design, rather than in their superior electrical properties. As a matter of fact, pole pieces from iron powder have found their principal field of usefulness in small electric motors for controls and similar applications where the highest possible flux density in a given design is not required. Fig. I shows a number of different designs for pole pieces made from iron powder. The steps involved in fabricating them are: (I) briquetting—with each stroke of the briquetting press a complete . pole piece is produced; (2) sintering, and (3) sizing, which is a one-step coining operation in a hand-operated punch press. Conventionally small pole pieces are made from laminated electrical sheet steel stock by punching out the laminations and riveting them together (Fig. 2). The powder method has the advantage of being rapid and inexpensive; also, it makes possible the molding of pole pieces with a round hub, which are better from a design standpoint, as will be shown later. It is difficult to make such round-hubbed pieces from laminated stock. The pole pieces could, of course, be machined from solid stock, but this method is not widely used. The raw material for making pole pieces from powder is straight iron powder without the addition of any alloying ingredients. However, the grade of powder used is of considerable importance, as will be shown later when the influence of the grade of iron powder upon the magnetic properties is discussed. Pole pieces are briquetted in the same way that other iron-powder machine parts are made. Because the pole pieces are flanged—i.e., they have a hub and a wing section—they are made in presses that apply pressure from both ends. For best mechanical and magnetic properties, the density throughout the piece should be even and also should be constant from piece to piece. For that reason a powder of constant compressibility from batch to batch is needed for briquetting pole pieces. One method of obtaining the required magnetic properties is to sinter the pole pieces at temperatures higher than are used for most iron-powder parts. A temperature of 2400°F. and an atmosphere of hydrogen has been found satisfactory. No automatic furnaces of the roller hearth or mesh-belt type have yet been developed for such high temperatures. A box-type furnace heated with Globar heating ele-

Jan 1, 1945