Search Documents

By W. C. Taylor

The present fuel situation indicates that, at least for the next 20 to 30 years, the burning of coal will be a main source of energy. All coal contains sulfur, which is converted to sulfur dioxide during combustion. The concentration of sulfur dioxide (SO2) in the resulting flue gas, for most coals, would exceed the limits established by the Environmental Protection Agency (EPA). Therefore, the sulfur must either be removed from the coal prior to its burning, or be collected from the stack gas before it reaches the atmosphere. There is currently a large amount of research devoted to methods of removing the sulfur from the coal before burning, or during combustion in fluidized beds with materials which trap the sulfur in the solid residue. The commercialization of these processes, however, is not expected in the near future. Flue gas desulfurization appears to be the best near term prospect of fulfilling current air quality control regulations. The lime/limestone wet-scrubbing methods are the most advanced flue gas desulfurization processes and will account for the majority of sulfur removal systems in electric power generation. There are currently at least 23 full-scale systems existing or under construction and 17 of these will use the lime or limestone wet-scrubbing process. (1)

Jan 1, 1974

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and, (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke. This is the third of a series of reports giving results of studies by counties under part (1) of the investigation. This report covers Pike County, Ky., which comprises parts of the Harold, Williamson, Matewan, Gilbert, Pikeville, Regina, Hurley, Pound, and Clintwood quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By Maria Cristina Yukiko Nakayama

Este trabalho estuda a obtenção do cobalto metálico a partir da redução de pós de óxido de cobalto (Co3O4) usando como agentes redutores o plasma frio de hidrogênio e o gás de hidrogênio. A redução a plasma foi realizada sob tensão de 540 V e largura do pulso na faixa de 140-170ms, e da mesma forma que na redução a gás foram usadas as seguintes condições: fluxo de 300 cm3/min de hidrogênio, pressão de 530 Pa, temperaturas de 250º, 300ºC, 350ºC e 380ºC e tempos de 10 a 120 min. Os resultados mostraram que o processo de redução ocorre em duas etapas: Co3O4?CoO?Co. Na parte mais externa das partículas parcialmente reduzidas verificou-se a presença de altas concentrações de cobalto e no centro das mesmas, altas concentrações de oxigênio, o que indica que a redução se dá da superfície para o núcleo. Constatou-se que em 300oC após 120 min é possível obter frações de metal reduzido aproximadas de 0,93 quando é utilizado o plasma frio de hidrogênio, enquanto o gás permite obter frações de apenas 0,3. A energia de ativação para a redução por plasma de hidrogênio é de 35,38 kJ/mol, ao passo que a associada ao gás de hidrogênio é de 90,79 kJ/mol.

Aug 16, 2017

By C. M. Diaz, P. J. Mackey

Since its inception, in 1987, the Copper-Cobre series of conferences has established itself as the prime world forum for discussing advances in copper process metallurgy, in particular copper sulfide smelting, copper recovery by leaching and electrowinning and copper electrorefining. All copper producing countries have actively participated in the pyrometallurgy symposia held in the framework of these conferences. In 1999 and 2003, the close to 100 pyrometallurgy papers that were presented had to be accommodated in two volumes. In the present paper, the authors firstly provide a brief historical sketch of the Copper-Cobre conferences and then focus on providing a retrospective look at the dramatic changes that have taken place in copper smelting in the last few decades, primarily as discussed in the Copper-Cobre and precursor conferences pyrometallurgy proceedings. Topics include: the development of autogenous, increasingly more intensive, environmentally sound and energy efficient smelting processes; significant improvements in Peirce-Smith converting practice and at the same time the commercialization of alternative continuous converting routes; the consequent expansion and modernization of smelters; the increasing compliance with strict government environmental regulations in most copper producing regions of the world; the realignment of the copper smelting industry throughout the world; and trends in copper smelting R&D. A look at the future closes these reflections on the contribution of the Copper-Cobre conferences to the advancement of copper smelting technology.

Jan 1, 2007

By R. G. Burdick

The problems presented by old mine workings affect both present day mining and land development. An automated method of locating these old mines from the surface using electrical resistivity techniques was de-veloped earlier under a Bureau of Mines contract. Subsequent Bureau research has refined the techniques and expanded the area of study to a variety of geologic provinces. During this research, six mining areas in the United States were in-vestigated with the Bureau's automated resistivity method. This report describes the mining areas involved and the results of the resistivity investigations, which showed a high rate of success in detecting old mines. It also describes the field measurement techniques and data analysis procedures.

Jan 1, 1986

By M. Laframboise, M. Buarzaiga

High-pressure acid leaching (HPAL) of nickel laterites has received considerable attention in recent years. High paymetals extraction, good selectivity, and advances in pressure hydrometallurgical technology are some of the reasons for this interest. Falconbridge Limited (Sudbury. Ontario) investigated the HPAL process using both fresh water and seawater for ore processing. The use of seawater resulted in a chloride concentration of 7.8 g/L in the autoclave feed. A test program was developed to study the effect of process water and leach temperature on the leaching behaviour of different ore compositions from the Koniambo deposit in New Caledonia. The work showed that salinity has a major effect on autoclave chemistry. This paper explores the results.

Jan 1, 2004

"The pressure leaching of alkali-pretreated limonitic laterite ore in nitric acid was studied. The optimal leaching conditions are as follows: leaching temperature of 458 K, initial nitric acid of 2.44 mol/L, leaching time of 60 min, liquid to solid ratio of 2:1 mL/g, agitation speed of 500 RPM. Under the above conditions, the extraction of nickel and cobalt can be achieved as approximate 95% and 80% respectively while that of iron is as lower as 1%. The leaching residue containing 70% of iron in the form of hematite and trace amount of chromium is suitable as the raw material for iron-making. The nitric acid in the leaching solution can be regenerated and further recycled to leach. INTRODUCTIONIt has been estimated that 60%-70% of the world land-based nickel resources presented in nickel laterites containing 130 million tons of nickel although these only accounted for about 42% of the world nickel production (Sudol, 2005; Luo et al., 2010). The nickel resource of laterite has not yet been fully utilized. Due to the increasing global demand of nickel and the declining global reserves of nickel sulphides, there is an increasing focus on the processing of the huge reserves of laterite ores today. Nickel laterite ores can be simply divided into two types, namely, silicate-rich and limonite. The former can be treated effectively by pyrometallurgical process in which the ferronickel product or nickel/iron sulphide matte is produced (Monhemius, 1987). The limonitic laterite is rich in iron in the form of goethite which is the main nickel-bearing mineral and usually contains cobalt associated with a manganese phase (Chang et al., 2010; Georgiou and Papangelakis, 2004). The limonitic laterite is usually processed by hydrometallurgical methods, such as atmosphere acid leaching (AL) (Xu et al., 2005; McDonald and Whittington, 2008), high pressure acid leaching (HPAL) (Chou et al., 1977; Georgiou and Papangelakis, 1998; Rubisov et al., 2000; Whittington and Muir, 2000) and reductive roasting-ammonia leaching (Caron Process) (Whittington and Muir, 2000; Valix and Cheung, 2002). The AL process can proceed at lower temperature, thus the operation costs may be very low. But two biggest problems associate with the AL process, namely, the slow rates of nickel extraction and potentially the significant amount of impurities such as iron and aluminum in the leaching solutions, which hampers the wide application of the AL process. The Caron Process uses the pyrometallurgical and hydrometallurgical methods together to obtain the metallic values, but the overall metal recovery is relatively low, especially for cobalt. In recent years, the environment-friendly process of HPAL has become increasingly important because it is most suitable for low-grade ores and leads to high extraction of the valuables. However, the HPAL process needs a much higher temperature and pressure (503-533 K, 4-5 MPa) to maintain a relatively fast leaching rates, which results in higher operation costs. Moreover, another serious problem of scale formation in autoclaves occurs in the HPAL process, for example, in Moa Bay, up to 20 cm scale may build up resulting in 5 days descale downtime per month. In addition, the iron residues cannot be utilized for ironmaking due to the presence of high content chromium (Ema and Harada, 1987; Owada and Harada, 1987; Takagi and Furui, 1987)."

Jan 1, 2012

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By Harrison Cooper, Stephen Pack

"Data from samples taken during rotary air blast and reverse circulation drilling are crucial to properly assessing economics of mineral deposits in the case of exploratory work, and are equally critical in accurately delineating ore and waste in execution of mine operation plans. Past studies of sampling procedures, comparing results of conventional splitting to more precise extraction of representative samples, illustrate the significant degree of error frequently encountered. Economic impact of error in mine blast hole sampling work can be shown to result in theoretical losses valued at millions of dollars annually in operating large scale mining projects. Results of past drill sampling studies are reviewed.Drill sampling technique can be improved by collecting coarse and fine particles together and extracting samples for assay from the complete flow of rock and dust simultaneously. This can be accomplished with a collection unit attached to the drill stem through which all except a small proportion of extreme fines are retained. The bulk mass can be static sampled as flow takes place through the collector when size reduction is not required. Alternately, collected mass with fines and coarse intermingled can be processed for increased accuracy through size reduction to obtain proportional samples."

Jan 1, 1999

By Hugh M. Roberts

DEVELOPMENT at Steep Rock lake has given rise to renewed interest in the geology of the iron ore deposits in the Lake Superior Region and has implications of no small moment bearing upon methods of exploration in the Precambrian Shield generally. Following upon the Regional Lake Superior meeting of the American Institute of Mining and Metallurgical Engineers in August, 1941, the authors prepared a paper on the Steep Rock deposits, which appeared in the A.I.M.E. publication, Mining Technology, for January, 1943. Between Januar7 and April, 1943, exploration at Steep Rock was continued by means o vertical, Mesabi-type churn-drill holes put down from the ice. This drilling has enlarged the tonnage of ore previously known and has disclosed further facts relating to the origin of the ore. The added evidence, we believe, goes to support the hypothesis that the deposits were formed by a process of replacement due to upward-moving, iron-bearing solutions which came in as igneous after-effects. Accordingly, in presenting the subject to the Canadian Institute of Mining and Metallurgy, it seems best not to change our first explanation, but to prefix the original paper with an interpretation of the results of the more recent explorations completed after its publication.

Jan 1, 1943

By C. R. Stephan

There are a large number of facilities throughout the world which handle coal, such as preparation plants. Many other facilities use coal as a fuel, such as cement and lime factories. Although coal can be handled safely and can be an efficient fuel, there are explosion hazards which are accentuated as the particle size is reduced. Particle sizes of coal which can fuel a propagating explosion occur within thermal dryers, cyclones, baghouses, pulverized-fuel systems, grinding mills, and other process or conveyance equipment. This paper discusses how explosions can occur within these facilities.

Jan 1, 1998

By Eric B. Sansone

The Federal Coal Mine Health and Safety Act of 1969 requires coal mine operators to sample accurately the amount of respirable dust in the mine atmosphere. A technique approved for such sampling employs a 10 mm nylon cyclone followed by a membrane filter (nominal pore size ????= 5 µm) and a pump. The pump is required to provide a flow rate of 2.0 ± 0.1 liters per minute. Calibrations have yielded a range of flow rates (1.4 to 2.8 1pm) at which the cyclone should be operated to remove the non-respirable portion of the dust. The purpose of this project was to evaluate the performance of the 10 mm nylon cyclone at flow rates of 1.8 and 2.0 1pm using a polydisperse coal dust aerosol. The penetration characteristics of the cyclone were to be compared to the United States Atomic Energy Commission's respirable dust standard. The effect of relative humidity on cyclone penetration characteristics was also to be observed.

Jan 1, 1973

The sulphide ore occurring in the North Mine at Broken Hill is of a complex nature, consisting of an intimate mixture of argentiferous galena, marmatite (zinc-iron sulphide), and gangue minerals. A typical analysis of the ore is:Lead 15.2%Zinc 12.0%Iron 5.3%Manganese 0.8%Copper 0.1%Alumina 0.3%Lime 0.9%Sulphur 11.1%Insoluble 53.8%Carbon dioxide 0.3%Undetermined 0.2%Silver 9 oz. per tonTotal 100.0%The metallurgical practice for the recovery of the lead concentrate and zinc concentrate from the crude ore is briefly described in the following pages.(1) COARSE CRUSHING AND FINE GRINDING OF THE CRUDE OREThe crude ore from the mine, containing lumps to the size of, roughly, 10 in. x 8 in., is tipped over grizzlies with the bars spaced 3 in. apart; the oversize gravitating to a...

Jan 1, 1933

By Edward Kline

A review and synthesis of literature pertaining to biological consequences of submarine mine-tailings disposal (STD) was conducted. STD can result in massive sea floor sediment deposition. STD may also increase suspended sediment, trace metals, and residual milling reagents in receiving waters. These perturbations, which are highly site dependent, invariably smother benthic organisms, and could potentially affect or alter fish, plankton, and benthos through acute and chronic toxicity, bioaccumulation, behavioral changes, smothering, derived secondary effects, and habitat alteration. Much of the available information concerning STD is unpublished and limited to a restricted number of sites. From this information and related research, it appears that benthic smothering is the only major consequence of a properly designed STD system. There have been cases of metal bioaccumulation due to inadequate preliminary evaluation, Also, shallow water habitat alteration has resulted from STD. Reductions in biological production are likely due to benthic smothering. The rate of ecological recovery after termination of an STD operation varies and is difficult to assess, The consequences of STD are site specific. Additional research is needed concerning possible consequences of milling reagents and the broad implications of benthic smothering. Also, methodologies are needed to allow better prediction of benthic recolonization and ecological implications of metal bioaccumulation.

Jan 1, 1994

R. Dawson Hall, who has long been a member of the editorial staff of Coal Age, has been appointed managing editor. Increase the Promise of the future. Buy W. S. S.

Jan 7, 1919

By A. Ignatow

"A review is made of some of the principal factors and conditions that are, and will be, important to the over-all market climate for asbestos fibre and for the future of Canada's asbestos industry: - health hazard associated with asbestos exposure;- uncertain international regulatory environment for continued asbestos use;- adverse public reaction to asbestos;- product liability/litigation costs (U.S.A. primarily);- promotion of substitution by governments and asbestos user industries; and- minimal product and market development efforts by asbestos producing and consuming industries.In addition, Canadian producers, who export some 95 per cent of their production, face additional constraints:- dramatically reduced integration with asbestos-consuming industries;- 60 per cent of exports to most rapidly declining markets (U.S.A., Europe);- increased competition from offshore producers favourably located to growth markets in developing countries;- increasing production costs;- a strong dollar;- disadvantageous freight rates; and- loss of price leadership and price erosion.Future market trends, as well as prospects for Canada's asbestos industry, will be projected in this paper.Economic FactorsTable 1 presents asbestos fibre production in all countries for the period 1980-82. In certain instances, e.g. U.S.S.R. and China, these are capacity estimates as production statistics are not officially published. The U.S.S.R, by far, is the world's largest producer accounting for some 50 per cent of world production, though most production is consumed internally or by COMECON countries. It is estimated that some 700 plants produce asbestos-containing products within the U.S.S.R.Canada accounts for some 25 per cent of world production though it ranks first in world trade. Other important producers are South Africa Zimbabwe, Brazil and Italy. Since 1979, Canada's asbestos mining industry has experienced a dramatic drop in production and exports of asbestos fibre, as demonstrated in Table 2."

Jan 1, 1985

By C. J. Newman

Production levels at the Kidd Creek copper operation increased during the 1980's by expansion of both the smelter and refinery and by major modifications to equipment which was causing bottlenecks. As a result, there was a significant reduction in the unit cost, some manpower reductions and hence a significant increase in productivity. In the last two or three years, there have been no major expansion projects leading to unit cost reductions and yet these have still been attained. This has been achieved by the development and implementation of various techniques designed to maximize the inherent potential of the operators and maintenance employees. This paper will initially describe the operation but will then place emphasis on employee involvement through such methods as idea awards, incentive schemes, loss control and continuous improvement programs. Organizational changes are discussed, particularly with reference to changes from the traditional operator role to one which encompasses maintenance skills and to cross-training of maintenance employees into multi-discipline fields. The effect of these changes are discussed by a review of the salient plant parameters of safety, production levels, cost and quality.

Jan 1, 1993

By Sen-xiang Yang, Xin-teng Liang, Gui-jun Li, Jian-hua Zeng, Yong Chen

"This research is based on PANSTEEL 120t steelmaking converter technology to have the quantitative description of the time needed in uniform mixing of molten steel in the converter with the computer. In present work, the numerical simulation approach is used to analyze oxygen lance nozzle, the flow condition of oxygen and flow status of molten steel in the converter. The various oxygen jet flows that come out from different angles and the flow status of all kinds of jet flows in the converter have also been simulated. All of the simulation parameters are based on the specifically practical conditions according to the physical conditions of PANSTEEL 120 t steelmaking converter. Through numerical simulation, the angle parameter of the oxygen lance nozzle is 16 °. The optimized oxygen lance 536-16 has a good performance in industrial application. This kind of phenomenon shows that the ways and processes of numerical simulation in this research are right.IntroductionThe oxygen lance system is the significant process in semi-steel making converter. It's related to whether the converter or even the whole system can function well. While in actual production, many problems emerge in the process of using the former oxygen lance, such as re-drying, slopping, high lance position, dead burning and even blowing out. In continuous fast-paced process, the unstableness of oxygen lance will lead to speed droop or even stop pouring. Analysis shows that all these problems are not only related to the raw materials but also the design of oxygen lance. Bad oxygen lance's scorification kinetics condition and low content of FeOn in early slag are the direct factors that we cannot easily control in steelmaking at present [l]. Therefore, the good scorification kinetics condition which is related to nozzle has good influence on BOF steel making."

Jan 1, 2013

By J W. Muir, N Bedford

Hong Kong is one of the most rapidly developing cities in the world. With constant population growth and limited opportunities for space, the development of a fast and effective underground public transportation network is essential. Hong Kong’s Mass Transit Railway (MTR) Corporation is currently undertaking several large underground expansions to its existing network. Much of the excavation will be carried out using the drill and blast excavation method.Drill and blast excavation is common in Hong Kong and with the continued development of underground infrastructure the use of the drill and blast excavation method will increase. Although an effective method of excavation, the blasting vibrations caused during construction can have an adverse impact on surrounding structures and impose disruption on the local community.In order to minimise the risks associated with blasting vibrations, and to demonstrate that the impact on local stakeholders will remain within acceptable limits, it is generally necessary for a contractor to submit a blasting assessment report for approval by government authorities before blasting may commence.Continued increases in population density will force more infrastructure to be constructed underground. Tunnels and caverns are increasingly excavated in closer proximity to critical sensitive receivers. This leads to greater potential impacts on the community, tightening constraints on contractors and a higher level of confidence required for approval authorities. Finding a balance between the needs of the community and rising construction costs becomes more challenging.This paper presents a case study on how the blasting assessment report process has been successfully implemented for a major MTR project situated in a densely developed area of Hong Kong. It describes several methods of assessing blasting vibration impacts, innovative uses of blasting for excavation and the mitigation measures employed to provide the best outcome for all project stakeholders.CITATION:Bedford, N and Muir, J W, 2014. Blasting vibration assessment and innovative blasting methods in high-density urban environments, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 9–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Shilai Yuan, Huimin Lu, Liyuan Zhao, Zhijiang Gao

"A purification process was developed to removal impurity element boron from metallurgical grade silicon by electromagnetic induction slag melting. Vacuum melting furnace was used to purify boron in both Al2O3-MgO-CaO-SiO2 slag system and Al2O3-CaO-SiO2 slag system. The relationship between different slag chemistry and the removal of boron in silicon were studied using Back Propagation (BP) Neural Network model. The best slag chemistry for the removal of boron was predicted by Genetic Algorithm (GA) contributed by the use of Matlab. The results show that the mass fraction of Boron in silicon is reduced from 11.7496×10-6 to 2.3259×10-6 after slag melting in 28.96%Al2O3-3.43%MgO-36.24%CaO-31.37%SiO2 slag system. The relative error obtained with GA-BP Neural Network model was below 0.35%.IntroductionSolar energy, due to its low green house gas emissions, has been paid great attention. Accordingly, the demand for solar grade silicon (SoG-Si) has been growing rapidly. The quest for developing a low-cost method of producing SoG-Si has been moving forward in the last decade. Refining of metallurgical-grade silicon (MG-Si) attracts research interest due to its low material and energy costs, and more environmentally friendly technology in comparison to the traditional Simens process. As such, impurity elements in MG-Si must be removed to low levels for the photovoltaics (PV) cell to operate at optimum efficiency. Most impurities in metallurgical-grade silicon (MG-Si), especially metal elements, can be separated by directional solidification and the zone refining plasma-arc method [1, 2]. The main focus in refining MG-Si to SoG-Si is on the impurities which are the most difficult to remove. Boron has relatively high segregation coefficients (KB=0.8, concentration of Boron in solid silicon divided by its concentration in liquid silicon) [3] and higher vapor tension (the saturated vapor pressure of boron and silicon are 6.78×10-7 Pa and 0.4 Pa, respectively). The vacuum melting and directional solidification methods hence have no effects on boron removal.Slag refining involves melting MG-Si in the presence of a flux to produce a slag phase that can take up the impurity elements. The mechanism of slag refining is considered to include two main steps: the oxidation of boron and the absorption of boron oxide by slag materials. The oxidation of boron, described by the oxygen potential (PO2), resulting from the equilibrium Si and SiO2. The absorption of boron oxide, described as the slag basicity, is interpreted as expected to facilitate their extraction to alkali and alkali-earth oxides in the slag phase. Thus, effective removal may be obtained for a certain slag composition. Researchers [4-5] examined the effect of boron removal in CaO-SiO2 based ternary systems and showed that the addition of excess CaO can decrease the activity of SiO2. Researchers [6-8] studied the boron behaviors in CaO-SiO2-Al2O3, CaO-SiO2-Na2O, Al2O3-BaO-SiO2, CaO-SiO2-Li2O and Al2O3-CaO-MgO-SiO2 slag systems by adding boron in the silicon to a degree. Li2O, Na2O, MgO and BaO are thought to be associated with B2O3."

Jan 1, 2014