Search Documents

By T. L. Johnston

A review of technical literature of the last quarter century discloses that much experimental work has been carried on in an effort to develop commercial processes for making sponge iron. In addition to the work that has been recorded, other work has been done the results of which have not been published. The degree of success or failure of these investigators does not detract from the fact that the problem has its challenging aspects and practical possibilities that encourage further investigation. The purpose of this report is to record information derived from recent experimental work that .had its 'objective the development and demonstration of one method of producing sponge iron. Work of other investigators was studied and applied wherever possible.

Jan 1, 1948

By A. J. Sideris

It is known that Mg can act as a catalyst/solvent in the high pressure high temperature diamond synthesis. However, above pressure levels of the order of 7 GPa, and temperatures from 1700 ? 1800oC, it was not possible yet to use Mg for the industrial production of diamond. A possible alternative is the use of MgNi based alloys. However, owing to the great Mg reactivity, it was consider, so far, a difficult task to deal with such alloys. The present work presents successful results regarding the production of MgNi alloys, with different composition, at high pressure conditions. The behavior of the alloys and their microstructural characterization is analyzed.

Jan 1, 2006

By T. Iwanowski

Stress wave measurements and calculations are often used to make a safe determination of the bearing capacity and the integrity of driven piles. Some applications to the restoration of old buildings in the Old Town of Stockholm are referred to and especially analyses of measurements combined with simulations are discussed here.

Jan 1, 1991

Gold, silver and palladium may be separated from the other base metals and sulphur contained in copper sulphide precipitates derived from the Sherritt-Gordon nickel process using a process involving an oxidation roast, a reduction roast and a Cu(II)/acetonitrile leach. Sulphur is removed as SO, in an oxidation roast and the hot calcine is reduced with carbon, or with carbon plus cuprous chloride. The resulting product contains metallic copper which is readily dissolved with cupric ions in aqueous acetonitrile solution. Copper powder is recovered by thermal disproportionation. The residue contains the bulk of the iron and precious metals and may be treated by a number of methods, including direct cyanidation or melting with suitable fluxes. Melting the residue will produce a copper alloy containing the precious metals and remove the iron as a slag. The alloy can be recycled to the copper leaching stage or sent for toll refining depending on the precious metal content. Impurities from the leaching circuit are controlled by a bleed circuit which in one approach utilizes the SO, from the calciner to produce Chevreul's salt and separates copper from the soluble cobalt and nickel. Alternatively, the bleed may be directed back to the main refinery copper boil stage or oxydrolysis stage.

Jan 1, 1982

By Sam Kangwa, Thomson Sinkala

In the mining industry, drilling accuracy has a significant effect on the economy of operations. In this paper, results from the Nkana Division of the former Zambia Consolidated Copper Mines are presented. For the stope investigated, it was found that the extra operational costs alone were 462% of the planned costs! Clearly, there is more than good reason to pay attention to drilling of good quality holes.

Jan 1, 2004

By Malcolm Scoble, Jean-Marc Robert, Luciano Piciacchia

"An approach to the in situ testing of mine backfills is outlined. It has been developed to provide a measure of the effective strength and stiffness of such materials after placement in stopes. This paper is based upon recent field studies undertaken at five Quebec mines. Details of the selected instrumentation, supporting equipment and testing procedures are reviewed. The mechanical behaviour of the backfills is reported and related to their physical properties. This approach represents an economical, simple and reliable means to assess the mechanical characteristics of backfill materials as an aid to both mine design and placement quality control. IntroductionDevelopments in backfill and mining method technology are creating a pressing need to develop effective techniques for characterizing the physical and mechanical properties of backfill in situ, rather than relying on traditional laboratory testing. The development of bulk mining methods is creating the requirement to more fully understand the nature of exposed fill faces to design for stability in pillar recovery operations. Other backfill technological developments currently receiving widespread attention are high density placement and the use of alternative additives to Portland cement. In Canada, U.S.A. and South Africa attention is also being placed on employing backfill to alleviate rockburst hazards(1,2.3l. In situ testing offers the potential to measure the geomechanical properties of backfill once placed in stopes , in order to assess its actual role in pillar recovery and ground support. Similarly, it offers the ability to provide some quality control during backfill placement. This role is seen as becoming increasingly important with the growing recognition of the need to pay greater attention to the mode of placement, which governs segregation and variation in the properties actually achieved by the backfill after placement."

Jan 1, 1987

By R B. Evans, M G. Townsend

In Northland, New Zealand, localised large deposits of halloysite clay have been produced by in-situ alteration of rhyolite volcanics of Pliocene or Pleistocene age, which were erupted through pre-Pliocene sedimentary strata and locally through Pleistocene basalt; and which were subsequently onlapped by further basalt flows. Alteration to clay has been a result of both hydrothermal and of meteoric processes, and decreases in intensity of alteration with increasing depth. The raw material is crushed and fractionated to produce a product of less than two micron particle size, which is of exceptional whiteness and brightness. The unique properties of the clays render them highly desirable for specialised ceramic purposes.

Jan 1, 1990

By Peter (Yunqing) Zhang

Longwall recovery under weak roof conditions could have considerable delay if the immediate roof is weak and deteriorates during screening. A pre-driven longwall recovery room is a feasible solution to minimize the impact of longwall move on production. In this longwall recovery project, a 16-ft recovery room was pre-driven to cover screening, and the shearer cut another 16 ft outby to reach the final recovery line. The pre-driven recovery room was carefully monitored as the face was approaching it. The longwall face operated very well as it cut into the recovery room. The recovery process took about 13 days, and considerable time was saved compared with the previous panel. The support in pre-driven recovery room was designed to handle both front abutment pressure and weak immediate roof conditions. Pumpable standing support was used to support the cantilevered roof as the fender pillar narrowed and collapsed when the face cut into the recovery room. To ensure the stability of the recovery room, 3-D computer modeling was used to evaluate the support system. Abutment pressure, critical fender pillar width, bolting system, pumpable cribs and shield support were considered in the model. The recovery room was carefully monitored during longwall recovery. Roof-to-floor convergence and crib convergence were recorded every shift as the longwall face was approaching the recovery room. Roof, floor and pillar activities and crib performance were also observed as the face cut into the recovery room. This paper presents the support design for the recovery room, evaluation of the support system through computer modeling, and details of the monitoring results.

Jan 1, 2006

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005

Test Work on High Throughput Diamond Tracer Recovery from Alluvial Recovery Tailings with a Containerised Optical Sorter Under Real Production Conditions Worldwide alluvial diamond deposits are traditionally processed with dense media separation and XRF sorters, hand picking or grease tables. The test work conducted verifies the performance of an optical sorter detecting the transparency of particles for diamond recovery from the DMS concentrate, eg XRF-sorter and handpicking tailings. The containerised setup enables economically feasible, high throughput, semi-mobile setups to retreat recovery tailings from alluvial and also primary deposits. The test work has been conducted with quartz and glass particles, which are less transparent or comparably transparent, under realistic production conditions on a 600 mm belt machine with an installed electrical power of only 21 kW. The results show that 99 per cent recovery can be reached at a throughput of 10 t/h in the -8 + 2 mm fraction and at 22 t/h in the -25 + 8 mm fraction. At a throughput of 18 t/h a recovery of 88 per cent has been assessed. At a further escalation of the throughput, dust in the sorter container made sorting impossible in the coarse fraction and the recovery decreased significantly in the fine fraction. Analysis of the belt coverage indicates that higher throughputs of the coarse fraction can be fed onto the optical sorter if the dust extraction system is improved. The results are basis for the decision to conservatively feed 20 t/h of the coarse fraction and 17 t/h of the fine fraction in day to day production. The settings have been applied to sort alluvial recovery tailings in South Africa and will be applied to sort the recovery tailings of a primary deposit in Lesotho. The test work has shown that an optical sorter can be used to retreat recovery tailings with high throughputs. The compact setup of a screen and a 9 m standard container enables semi-mobile, temporary setups for small recovery tailings dumps and remote areas. In addition, sorting on transparency ensures the recovery of high value low-fluorescent diamonds.

Sep 13, 2010

By Sergio Neves Monteiro

The efficiency by which an applied load is transmitted through the composite structure depends on the strength of the interface between the matrix and the second phase. In fiber reinforced composites, the interfacial shear stress plays a major role in the composite capacity to support the applied load. This interfacial stress can be obtained by means of pullout tests using the fiber embedded to a certain length in a socket of the matrix material. In the present work, pullout tests were performed to evaluate the interfacial shear stress of ramie, a relatively strong natural fiber, reinforcing polyester matrix composites. The general result permitted to calculate a critical length for the ramie fiber embedded in polyester resin. From this critical length, the value of the interfacial shear stress was calculated. An interpretation of this result together with SEM observation displayed a relatively weak bond between the ramie fiber and the polyester matrix.

Jan 1, 2010

By S. Prasad

The effectiveness of ultrasonic velocity measurements and attenuation of the propagating pulse was evaluated as a means of Non-Destructive characterization of cold worked and annealed copper. Commercial copper is subjected to mechanical working such as forging, rolling and thermal treatment to induce re-crystallization. The microstructural changes that occur in copper and a variation in its mechanical properties are subjected to analysis using the ultrasonic technique. The signal processing is carried out using the wavelet analysis technique. The features of wavelet analysis namely, localization in space and the presence of an infinite set of basis functions allows removing noise from the time series and components of a non-stationary signal to be analyzed. This is seen to improve the accuracy of the results obtained from the ultrasonic technique in the case of copper, which has distinct coarse grains that are difficult to inspect due to backscattering from the grain boundaries.

Jan 1, 2010

Alluvial gold mining in New Zealand and in particular on the West Coast underwent a renaissance during the early 1980's. This was based on two main factors: a) the sharp rise in the gold price b) the advent of the hydraulic excavator with which to mine the auriferous gravels. The scale of operations varies considerably. A small operation typically consisting of one or two people using an excavator to feed either a land based or pontoon mounted (floating) gold recovery unit, which will typically feature a rotary screen with or without a tailings stacker with the screened fines < 10 - 15 mm) fed over riflle tables. The largest screening plants of this type are operated by DML Resources in their Arahura and Mikonui mining operations where the plants have the capacity to screen up to 250 m3 of gravel per hour. These plants usually employ jigs and centrifugal concentrators for gold recovery. Unique amongst current operations is the Grey River Dredge, a bucket ladder dredge capable of processing 700 m3 per hour similar to those that operated earlier this century. Gold concentration is by a series of jigs. The number of plants operating in recent times peaked at around 130 in 1987 (coinciding with a nominal average gold price of $751) and since that time has steadily declined to 80 units in 1993 and about 45 - 50 units today. This cycle of rapid expansion and then steady decline has been repeated on the West Coast since the original gold discoveries in the mid nineteenth century.

Jan 1, 1996

By G. F. Vander Voort

The accident at Unit No. 2 of the Three Mile Island nuclear reactor (TMI-2) on 28 March 1979 was the worst nuclear accident in US history and crippled the nuclear industry. An international Vessel Investigation Project was formed to assess the integrity of the vessel. However, it was not possible to remove specimens from the lower head until January?March 1990. Fourteen of the fifteen specimens removed by electrical discharge machining were from under the debris pile that accumulated on the lower head due to melting of approximately 19 000 kg (45%) of the core. Specimens were previously cut from the lower head of a cancelled reactor of very similar size and design destined for Midland, Michigan. These specimens were subjected to controlled heating cycles with peak temperatures from 800°C to 1100°C for periods of 1 to 100 minutes. The initial study qualitatively compared the structures in the 15 specimens from TMI-2 to the control specimens from the Midland lower head. The writer used the same specimens and employed microindentation hardness traverses, electron microprobe analysis, and selective etching followed by quantitative metallography (by image analysis) to obtain a far more detailed description of the thermal exposure experienced.

Jan 1, 2013

By Thomas M. Barczak

State-of-the-art longwall roof supports provide effective strata control, but failures of these support systems still occur. To identify failure mechanisms and the impact these failures have on the safety of the support system, the U.S. Bureau of Mines has been conducting research on shield mechanics in the Bureau's unique mine roof simulator, as well as field studies of in situ support loading and investigations of longwall failures, Three types of failures are discussed: (1) inadequate support capacity, (2) structural failure, and (3) instability. Hypothetical situations with proposed courses of action and case studies of actual longwall failures are described. This information is intended to assist the Mine Safety and Health Administration (MSEIA) and industry mining personnel in safety evaluations of longwall roof support systems.

Jan 1, 1989

By L. T. Isaacs, W. H. Traves

A numerical model for analysing the drainage of fill in mine stopes has been described. The model can be used to analyse the process of fill drainage in existing and proposed mine stopes. The validity and potential value of the model have been established by experience with a simpler, 2-dimensional numerical model and by testing the new model against the earlier model. The new model is more useful than the 2-dimensional model because it allows for heterogeneity of fill material within the stope - a factor that has been demonstrated to affect drainage characteristics significantly. The 3-dimensional model is also capable of predicting pore pressures and drainage rates at specific locations in the stope without the need to resort to 2-dimensional generalisations. Such information, integrated with relevant field data as they become available, will provide valuable mine planning information for the scheduling of filling operations and design of fill mixes

May 1, 1991

By Robert Hopler

As a part of the depression and rectification work on the Port Morris branch of the Harlem Division of the New York Central & Hudson River Railroad, a short tunnel is being driven under St. Mary’s Park. The park is near 149th St. and St. Ann’s Ave., in the Borough of the Bronx, New York City.

Jan 1, 2006

The solvent extraction section of an old Uranium Plant in the Vaal River region (North West Province in South Africa) produced a substance called CRUD (Chalk River Unidentified Deposit) that formed within the aqueous/organic interface of the settler of the solvent extraction circuit. The CRUD was deposited together with gold tailings to the tailings dam many years ago. Previous research done on the CRUD confirmed that exposed CRUD leaches Mn and Ni at concentrations that are well above their acceptable risk limits as well as Zn that leaches at concentrations that are slightly lower than its acceptable risk limit. Soil washing and bioremediation technologies were employed to treat the contaminated soil.   Various laboratory test work and the pilot scale studies were conducted in parallel with each other and the results of the laboratory studies were used to determine critical parameters. Four lixiviants, ie sulfuric acid, acetic acid, oxalic acid and ethylene diamine acetic acid were tested at three concentration levels ie 0.001 M, 0.0001 M and 0.00001 M, respectively. Column tests showed that the leaching of the heavy metals increases as the soil porosity increases. Silica sand was added to increase porosity of the contaminated soil. Highest Mn removal was achieved mainly by sulfuric and oxalic acid at 0.001M at all soil levels. EDTA was significantly efficient in the removal of Ni and Zn. The recovery of heavy metals, particularly Mn, decreased as the depth of sampling increased.   Heterogeneous bacteria and filamentous organism plate counts were conducted to evaluate the growth of the bacteria and filamentous organisms in the soil. Results showed that more organism growth took place in the bioremediated soil with a fertilizer added to it. The leaching of metals from the soil that was bioremediated in the pilot study was generally higher than the extraction of the metals from the soil that was leached with no bioremediation carried out. The results from this study suggest that the leaching of heavy metals from the contaminated soil is to a large extent dependant on the pH of the leaching solution. By increasing the soil's porosity and bioremediating the soil, higher extractions of metals were achieved.

Jun 1, 2010

By W. C. Phalen

The production of salt in the United States divides itself at the outset into two distinct classes…

Jan 1, 1915

By G. R. Corbett

The introduction of roof bolts to Phalen Colliery in the Sydney Coalfield, Nova Scotia (annual output of 2Mt) has been successfully implemented in maingate and tailgate entries over the last four years. Monitoring of the roof bolted areas continues to be an integral part of the quality control program as the results are utilized to maintain safety and to aid in long-term design strategies. Although all gateroads in the Phalen Colliery have converted to roof bolts as their primary means of support, the majority of intersections which intersect the main slopes remain supported by large steel structures. Several intersections within the Phalen Colliery were monitored as they were created by the mining process. A comparison is made between intersections supported with only traditional 6.4 to 6.7 m steel structure and intersections supported by 2.44 m fully resin encapsulated roof bolts in conjunction with 7.6 m fully cement grouted cable bolts. Detailed monitoring was conducted using CA NM ET's intrinsically safe sonic probe extensometer datalogger which has the ability to read up to sixteen probes simultaneously at programmed intervals. The density of the data from the datalogger has allowed a better understanding of the deformation of cable bolted intersections than was possible with manual monitoring. Test results have helped mine operators to design safer cable bolted intersections.

Jan 1, 1995