Search Documents

By Herbert J. French

ALLOY steels have become essential to industry in meeting the rigid requirements on materials imposed by our, advanced technology. In comparison with the total ingot capacity of the steel industry, the volume of alloy steels is relatively small although for many years annual alloy-ingot tonnage has, been in seven figures. However, the monetary value of the alloy-steel production is exceedingly high and the benefits derived from the products are relatively great. The trend in total ingot production since 1932 has been generally upward with only two major interruptions. That of the year 1938 was due to a decrease in general business activity whereas that of 1946 resulted largely from work stoppages. Traditionally, the tonnage of alloy-steel ingots produced was in the neighborhood of 5 to

Jan 1, 1948

By R. L. Bailey

"The Acheson D-3 Pool was discovered in August 1950, and contains 88 producing oil wells on 40 acre spacing. Initial oil-in-place was 118 million stock tank barrels and initial well potentials averaged 2,000 barrels per day.In early 1956 studies of hydraulic interference between the Acheson and Leduc D-3 Pools were conducted on the Carter Petroleum Reservoir Analyzer. These studies indicated that the natural water drive to Acheson would be incapable of replacing reasonable withdrawal rates over the life of the pool. To avoid shrinkage losses a scheme of pressure maintenance by water• injection was therefore instituted in March 1957.This pressure maintenance scheme is notable because pressure is being effectively maintained by high volume injection through one well located on the flank of the pool. Close control on reservoir behaviour is maintained by regular bottom-hole pres-sure surveys and observation of water cuts on producing wells. No evidence of pressure gradients or channelling of the injected water has been observed to date, and the water-oil contact has remained level over the whole field. It is possible to control the average reservoir pressure within very close limits by varying the rate of fresh water injection.Ultimate recovery estimated from the rise of the oil-water contact and calculated water influx to December 31, 1958, is 335 barrels per acre foot, or a total of 91.4 million barrels from the pool. This compares to 217 barrels Per acre foot or a total of 59.4 million barrels indicated from laboratory test data."

Jan 1, 1961

By Vincent Castranova, Jane Y. C. Ma, Joseph K. H. Ma, Chang-geng Mo, Carl J. Malanga

"A group of bisbenzylisoouinoline alkaloids has been shown to exhibit various degrees of effectiveness in preventing silica-induced fibrosis in animal models [1, 2]. The objective the present study was to characterize the binding of several of these alkaloids to phosphatidylcholine vesicles and rat alveolar macrophages using fluorometric and equilibrium dialysis methods, respectively. The lipid binding affinity of these alkaloids was found to depend upon several structural factors including hydrophobic substitutions, chiral configurations, and double oxygen bridge-restricted conformation of the benzylisoquinoline moieties. Tetrandrine, which is a highly effective agent in preventing fibrosis, showed strong binding to both lipid vesicles and alveolar macrophages. In contrast, certain analogues of tetrandrine such as curine and tubocurine, which have little or no effect on silicosis, exhibited only weak binding to lipid vesicles and almost no binding to cells. The moderate binding affinity of fangchinoline to vesicles and cells corresponded to a moderate effectiveness of the compound as an antifibrogenic agent. Methoxyadiantifoline, an alkaloid of unknown antifibrogenic potential, also exhibited high binding affinities for lipid and cells. In conclusion, the results of these studies indicate that alveolar macrophages exhibit large binding capacities for certain members of this class of bisbenzylisoquinoline alkaloids. A positive correlation was observed between binding affinity to alveolar macrophages and the reported antifibrotic potency of these compounds. These data also suggest that the ability of these drugs to interact with alveolar macrophages may be a key step in inhibition of the progression of silica-induced pulmonary disease.INTRODUCTIONInhalation of crystalline silica is associated with the development of silicosis. This fibrotic disease is characterized by the appearance of concentric hyalinized nodular lesions in the lungs with the progressive development of pulmonary dysfunction [3, 4]. Many theories concerning the etiology of silicosis involve silica-induced activation of alveolar macrophages. Evidence indicates that in vitro silica exposures result in the generation of chemiluminescence, and the release of superoxide and hydrogen peroxide from alveolar macrophages [5]. Activation of alveolar macrophages has also been demonstrated after intratracheal instillation or inhalation of silica [5, 6]. Such excess release of reactive products from pulmonary phagocytes has been associated with damage to the lung parenchyma [7, 8]. In addition, silica exposure results in the release of mediators from alveolar macrophages, which enhance proliferation of fibroblasts and collagen synthesis by these pneumocytes [9-12]."

Mar 1, 1992

The past four years since the 2008 MINExpo have been a roller coaster ride for the mining industry, with highs and lows and everything in between. One of the natural consequences of this uncertainty has been a number of significant consolidations and mergers, and this trend has trickled down into the crushing industry. And while there have been some significant changes to this sector of the mining industry, many of the big players have weathered the storm. The following is a look at some of the mineral processing companies that will be at MINExpo. McLanahan Corp. McLanahan Corp. is an example of the changes in the sector. The crushing and grinding stalwart acquired Universal Engineering, expanding its traditional focus on soft mineral crushing to hard rock crushing. At MINExpo, it will be showing off three new pieces of equipment, the LabMill Crusher, the Rocker Tooth Crusher and the Recessed Filter Press.

Jan 1, 2012

By Elma van der Lingen

Gold is considered the most inert of all metallic elements, but the metal can show catalytic activity when prepared by specific techniques. Preparation techniques being used to prepare gold catalysts systems mainly involve precipitation methods incorporating gold compounds or complexes. This paper introduces a totally different method for the preparation of gold-based heterogeneous catalysts that can be used for oxidation and reduction reactions, as well as electrocatalysts. The method involves alloying of gold with a less noble metal, such as aluminium, to form a gold-containing intermetallic precursor. AuAl2 was produced by melting gold and aluminium together in a vacuum arc furnace under a protective atmosphere. The aluminium is then dissolved from the AuAl2 precursor by means of NaOH to produce a highly porous gold structure. The paper also reports on a method of incorporating transition metal oxide(s) with the porous gold to form an active heterogeneous catalyst. Promoter elements can also be melted with AuAl2 to improve catalytic activity. Alloying has the advantage that the promoter element can be in contact on atomic level with the gold. In-situ xray photoelectron spectroscopy (XPS) studies have also been done on the porous gold catalysts to further clarify the CO oxidation mechanism on gold-based catalysts.

Oct 1, 2003

By B. W. Clyburn

"Coals from the Corporation's Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing all essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.Introduction Very high fluidity and unusually low ash are the outstanding characteristics of coal from Devco's mines in the Harbour seam of the Sydney coal field. However, sulphur content, mainly pyritic, ranges from 1 to 2.50Jo. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required. Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs. Typical data on the various coal properties of importance in the production of coke are included in Table 1."

Jan 1, 1985

Infacon 74 The National Institute for Metallurgy, the South African Institute of Mining and Metallurgy, and the Ferro-Alloy Producers' Association of South Africa extend a cordial invitation to participate in the International Ferro-alloys Congress to be held in Johannesburg, South Africa, in April 1974. Obituary RICHARD AUSTIN COOPER On the 31st March 1972, a once very active member of the Institute, R. A. Cooper, died at the age of 82. He had served on the Council for many years and was Vice-President in 1933/34. ALEXANDER JEREMIAH ORENSTEIN CB., CM.G., C.B.E., LLD., D.Se., M.D., M.R.C.S., F.R.CP., F.R.S.H. Dr Orenstein, who died on the 7th July 1972 at the age of 92, was so well known and so widely acclaimed during his lifetime that it is difficult to add to the tributes which have already been paid to him.

By Donald S. Colby

This Bureau of Mines report is essentially a handbook, or manual, for making the type of mineral resource valuation commonly required for such public policy problems as mineral leasing. The principle of resource valuation through the capitalization of cash flow is well established. A mathematical procedure, based on a simplified accounting system, is detailed for calculating cash flow from revenue, plant costs, and operating expense. Variations of procedure cover cost depletion, percentage depletion, and depletion limited to 50 percent of net income. The influence of the depletion provisions of the tax regulations on the value of a resource to an owner and to an operator is analyzed. The relationship of royalty, bonus payments, and sales price to resource value is also described, and methods for approximating resource values using these payments as input data are developed.

Jan 1, 1969

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

Jan 1, 1968

By E. G. Davis

Large-scale ultrafine grinding tests of a coarse kaolin were made using the Bureau of Mines developed attrition grinding process in continuous open-and closed-circuit systems. A 20-inch diameter attrition grinder, designed and constructed at the Tuscaloosa Laboratory, was used. Studies included single- and multiple-stage open-circuit grinding, and also continuous grinding tests in closed-circuit with a 6-inch-diameter solid bowl centrifuge. Clay feed, containing 9.0 percent minus-2-micrometer esd, was used at fates up to 840 pounds per hour. Multistage grinding tests gave better results than single-stage treatment when equivalent clay feed rates were used. Closed-circuit grinding tests yielded ground products containing slightly more minus-2-micrometer-esd clay than the open-circuit grinding when using the same clay feed. Energy consumption was lower in closed-circuit grinding than in batch or open-circuit grinding. A modified two-stage closed-circuit grinding system gave the best grade of product and amount of minus -2-micrometer-esd clay produced per pound of clay feed. The ground product from this test contained 88.5 percent minus-2-micrometer-esd material and electrical energy consumption was 327 kilowatt-hours per ton of minus-2-micrometer-esd material produced.

Jan 1, 1973

By T. Sun, J. Kou, C. Sun, D. Gong

"HPGRs (high pressure grinding rollers) have demonstrated higher energy efficiency than conventional comminution equipment due to their application of particle-bed breakage mechanism. In the past decades, a large number of studies have been conducted to understand the characteristics of particle-bed breakage, however, few of them concerned the difference between single-particle and particle-bed breakage in compression comminution. This comparison is able to demonstrate possible advantages of particle-bed against single-particle in a breakage event due to the isolation of the effect of force loading mechanism. The present study investigated progeny fragment size and energy efficiency of these two breakage methods at variable energy inputs and particle sizes. The results show that at low energy inputs of around 0.25 kWh/t, the numbers of fines resulting from the two breakage methods are very similar. However, at higher energy inputs of around 1.0 or 2.0 kWh/t, particle-bed breakage generated significantly more fines. From the perspective of newly generated surface energy, particle-bed breakage is obviously more energy efficient than single-particle breakage at energy inputs between 1.0 and 2.0 kWh/t. It was also found that HPGRs demonstrate high energy utilization rate in generating new surface energy within their typical range of specific energy input. INTRODUCTION Rock comminution is an important and energy-intensive process in mining operations. Nowadays, decreasing head grade and mineral liberation size of ore deposits greatly increase the energy cost of comminution process. HPGRs have been successfully applied in the mining industry to improve the energy performance of comminution circuits. Typically, 10 to 30% of energy saving can be achieved due to the application of HPGR (Wang et al., 2013; Casteel, 2005; Günter et al., 1996)."

Jan 1, 2018

By James P. Bennett

The Bureau of Mines investigated the role of imported natural flake graphite in dolomite-carbon refractories used in steelmaking processes. Fundamental engineering data were obtained to enable the evaluation of substitute materials. Changes in oxidation resistance (2,000° F), hot strength (2,750° F), and deformation under load (2,7500 F) caused by 10-wt-pct additions of five different kinds of natural flake graphite and increasing quantities (0 to 30 pct) of a 90-pct-carbon natural flake graphite were studied. Results indicated that carbon purity of 10-wt-pct-graphite additions did not influence hot strength or deformation under load. When the quantity of 90-pct-carbon graphite addition varied between 0 and 30 wt pct in a dolomite-carbon brick, hot strength was highest and de-formation under load lowest with 10-wt-pct additions. As hot strength test temperature was increased from 5000 to 2,750° F, the strength difference observed between 0-and 30-wt-pct additions of a 90-pct-carbon graphite became smaller. Additions of a boron-treated graphite caused significantly higher strength and lower deformation under load at high temperatures, while an addition of ball clay significantly reduced strength and increased deformation.

Jan 1, 1987

By Ionel Gardescu

IN connection with some of the experiments carried out by the writer on the behavior of gas and oil in a sand reservoir,1 an interesting phenomenon was observed which may throw some new light on the problem of recovery of oil from a natural reservoir. The experiments are intended to show the effect of the surface area of the occluded gas masses, originally present in a reservoir, on the further evolution of gas from the oil and its consequent effect upon the rate of production of oil. The apparatus used in the experimental work is shown in Fig. 1. It consists primarily of a sand reservoir R and a displacement chamber D, which is used to induce small variations in volume. The reservoir and displacement chamber form a unit, and a lowering of the plunger D is equivalent to increasing the volume occupied by the oil and gas in the reservoir. The reservoir was first filled with dead oil and maintained under pressure until it was ascertained that most of the free gas had gone into solution. The volume of free gas present in the reservoir was computed from the coefficient of compressibility of the fluids by means of the dis-placement chamber D, reading to 0.005 c.c. and a special gage J reading to 0.02 lb. per sq. in. The oil was saturated with gas under pressure in reservoir S by circulating the oil for a long period of time through the gear pump B. Subsequently, the saturated oil was circulated through the sand reservoir following the circuit S6, B, S5, R4, the sand reservoir R, R1, R2, F4, F1, back to reservoir S. In the following experiments the sand reservoir R was filled with gas-saturated oil at a pressure of 415 lb. per sq. in. with no free gas present. This was ascertained by. closing off all the outlet valves, and determining the coefficient of compressibility of the system by means of the dis-placement chamber D.

Jan 1, 1932

By M. D. Marshall

A survey showed that there were 24 bin-related fatalities in the 5 year period of 1975 to 1979 in the minerals industry. Only 4 victims wore safety belts and only 1 of these had a second person attending his lifeline, as mandated by Federal safety regulations. Not one victim observed the three main Federal safety regulations governing work in and around bins. A study was conducted on the force necessary to pull victims partially buried in sand and limestone. Recommendations are made on procedures and safety equipment that can minimize bin-related accidents. A Handbook, directed to the plant engineer responsible for bin design and safety, was also issued detailing bin designs and flow-aid accessories as a function of the flowability of the stored material to better maintain material flow from bins. A comprehensive table of the flowability of many materials produced in the minerals industry is presented and simple procedures given for determining the flowability of materials if not available.

Jan 1, 1984

By J. E. Tiffany

Some of the gases produced by permissible explosives on detonation are poisonous, and the probable hazard involved by the inhalation of carbon monoxide in the past has been evaluated from results of tests in the Bichel Gage. Tests have now been made in the Experimental Coal Mine of the Bureau of Mines at Bruceton, Pa., to determine the composition of the gases obtained under actual mining conditions for the purpose of comparing these, results with those found by the Bichel gage tests. Two permissible explosives were procured for these tests, one that produces a relatively low quantity of poisonous gases in the Bichel gage (24.8 liters per 1-1/2 pounds of explosive) and another that produces a relatively high quantity of poisonous gases (94.6 liters per 1-1/2 pounds). The first of these is designated by the Bureau of Mines as a class A4/ explosive and the other is designated a class B explosive. In comparison with Bichel-gage tests, the shooting of permissible explosives in a coal shot hole resulted in a large reduction in the quantity of carbon monoxide, the principal poisonous gas, which; in the mine tests, was only 22 percent of that found in Bichel-gage tests: The quantity of carbon monoxide from the class B explosive in Bichel-gage tests was 3.8 times larger than that from the class A explosive; in the coalmine tests the ratio was 4:1. The concentrations of carbon monoxide in the mine tests, as determined by analysis of the atmosphere in an enclosed space resulting from shooting 1-1/2-pound and 3-pound charges of the class A explosive, were 0.03 and 0.06 percent, respectively, and the concentrations from 1-1/2-pound and 3-pound charges of the class B explosive were 0.10 and 0.24 percent.

Jan 1, 1950

By Roberto Maldonado Astorga

El presente texto señala la implementación del modelo de gestión para las operaciones de Volcán Campaña Minera, basado en el Modelo de Gestión de Malcom Baldrige. El modelo tiene el objetivo de establecer un proceso sistemático y estandarizado que asegure la mejora contínua y en línea con la visión de la empresa que apunta al logro de la excelencia operativa. La estrategia se divide en tres módulos: Módulo de Organización, Módulo de Gestión y Módulo de Comunicación. Asimismo se busca, implementar círculos de optimización permanente, monitorear de forma sistemática la ejecución de iniciativas de mejora y seguir el impacto en los indicadores.

Nov 1, 2014

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan

During the last phase of the Circunvalacion Norte project in San Jose, Costa Rica, preliminary designs for an underpass structure of over 16 km (10 miles) considered drilled shafts as an earth retaining system. Since the project’s execution was delayed and close to the deadline, it was necessary to optimize this structure, with the drilled shafts being the most critical aspect. The key element in order to obtain an improved design was characterizing the job site with a specific site study for seismic demand, and the use of advanced numerical modelling, considering soil-structure interaction. The site investigation comprised the CPT, PMT, MASW geophysical tests, deep exploration drilling, and triaxial compression tests. The terrain was modeled using an advanced constitutive model with hardening plasticity calibrated from the triaxial tests. Plaxis software was used to calibrate the seismic model for the terrain and for the dynamic analysis. Two conditions were considered for the retaining structure: free-head and fixed head. A parametric study with drilled shafts of 1.0 m (3.3 ft) and 1.2 m (3.9 ft) in diameter, and center-to-center spacing of 1.3 m (4.3 ft) and 3.0 m (9.8 ft) was conducted in order to obtain an optimized structure. For each condition of the drilled shaft wall, the computed deformations were compared for two spectrum designs: site-specific spectrum and seismic code generic spectrum. Finally, a dynamic analysis was performed to check the performance of the drilled shafts with optimized spacing using a control earthquake. Based upon seismic performance curves, the analysis showed the possibility of greater spacing for the drilled shafts compared to the original design, obtaining a 32% reduction in the total length of the drilled shafts in the project.

Oct 1, 2022

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

By A. L. Nunes, J. R. E. Garcia, G. Silva, U. Prasad, C. Rabe

"Drilling through the Guayabal shales, a gray calcareous shale, and the C1 to C100 formations, a well-cemented calcareous-sandstone in Corralillo field, Mexico, is a challenge due to severe wellbore instability problems. Additionally, there has been a history of ineffective reservoir stimulations by hydraulic fracturing. To predict and mitigate these subsurface issues, it is essential to characterize the mechanical properties and rocks strength for a better prediction of borehole stresses and collapse pressure during drilling. Various correlations can be used to estimate and/or determine the unconfined compressive strength but most of them are based on transit time and porosity.In this study, grain size distribution was combined with acoustic travel time, porosity and static Young’s modulus to develop a rock strength prediction model for the turbiditic sandstones of the Chicontepec basin. The main reason this combination of parameters was employed was because of the wide variations in rock strength estimated using traditional porosity-based correlations such as the McNally’s (1987), GMI-Jizba-E’s and Bradford’s (Bradford et al., 1987).To develop a new correlation, a geomechanical and microstructural campaign was initiated. Mineralogy by X-ray diffraction, pore and grain sizes by petrography, clay distribution by SEM and porosity by mercury intrusion porosimetry were measured. Static and dynamic Young’s moduli and Poisson’s ratios were acquired by triaxial and ultrasonic measurements on undisturbed sandstone samples from the Chicontepec basin. More than ten offset wells with wireline data, including transit time, porosity, density, resistivity and gamma ray, were used for reservoir and geomechanical characterizations.Our analyses lead us to propose a new correlation for predicting the uniaxial compressive strength (UCS) of sandstones of the Chicontepec Basin as a function of transit time and grain diameter, both of which can be derived independently from destructive laboratory tests. Our results also highlight the importance and value adding of a combined approach incorporating grain size analysis in the rock strength prediction. The UCS predicted using the transit-time and grain-size-based model presents a median value (P50) of 76 MPa, P10 of 55 MPa and P90 of 89 MPa."

Jan 1, 2015