Search Documents

By Nicholas T. Esposito

An advanced coal preparation plant has been built at Homer City, Pennsylvania, by Pennsylvania Electric Company, a subsidiary of General Public Utilities Corporation, and New York State Electric and Gas Corporation, as an alternative to utilizing flue gas desulfurization technology to meet the Federal Environmental Protection Agency and the Pennsylvania Department of Environmental Resources air quality emission regulations of 4.0 lb S02/106BTU for the two (2) existing coal-fired generating station Units No. 1 and No. 2, and a 1.2 lb S02/106BTU for the new Unit No. 3. The coal preparation plant is designed to process 5,200,000 tons of run of the mine coal annually and has a design capability to process 1,200 tons per hour via two (2) equal capacity 600 tons per hour preparation circuits.- The plant is designed to produce multi-product coal streams consisting of a middling product of medium ash and medium sulphur content, which is environmentally compatible to support operation of the two (2) existing generating Units I and 2, and a deep cleaned, low ash, low sulphur coal product capable of environmentally supporting the ambient air quality requirements of the new Unit 3 generating facility. The waste product from the process consists of high ash, high sulphur reject material. The process has the acronym MCCS (Multi-Stream Coal Cleaning System).

Jan 1, 1982

By E. P. Klier, S. M. Grymko

The transformations in eutectoidal systems have been extensively studied as they occur in steels.&apos; As a consequence of these studies the martensite, bainite and pearlite reactions found for most steels are widely recognized. Further, because of the work of Smith and Lindlief2 and of Greninger and Troiano3 these reactions, except for the bainite reaction, are considered as typical for all eutectoidal systems. The primary alloy studied by Smith and Lindlief2 was a CuAl alloy of near eutectoid composition as was the alloy more recently studied by Mack.4 The transformations in these alloys were, for the most part, studied metallo-graphically, while an X ray analysis of structures was essentially wanting. It has appeared desirable, therefore, to investigate selected CuAl alloys at and slightly away from eutectoid composition. For this purpose three alloys were prepared containing 10.5,11.9 and 13.5 pct A1 respectively. The results of a metallographic and X ray analysis of structures obtained for isothermal transformation of the ß-phase are reported here for the 11.9 and 13.5 pct A1 alloys. Introduction The phase equilibria in the CuAl alloys of immediate concern are indicated in the equilibrium diagram section presented in Fig 1.5 The equilibrium and transition structures which have been reported in this system are as follows: a = copper rich terminal phase (f.c.c.) ß = high temperature eutectoidal phase (b.c.c.) r2 = aluminum-rich intermediate phase (r-brass structure) a&apos; = modified a-phase postulated by Bollenrath and Bungnrdt.26 ß1 = ordered ß (b.c.c.) ß&apos; = martensite structure: A1 < 13 pct (near h.c.p.) ß" = ß&apos; of Smith and Lindlief2 7&apos; = martensite structure: A1 > 13.5 pct (h.c.p.); ß2 of Bollenrath and Bungardt.26 The eutectoid transformation can be suppressed at sufficiently high cooling velocities. The ß-phase is then retained to about 500°C where ordering sets in. The ordering interval is not satisfactorily known but indirectly appears to be non-suppressible. Subsequent to the ordering reaction and consequently at lower temperatures, the ordered ß1 decomposes to a marten-sitic structure. The kinetics of these reactions and in particular those of the martensite reaction have an important bearing on the results obtained in this investigation. Since some confusion exists concerning certain reported aspects of these reactions, they will be considered in some detail. THE MARTENSITE REACTION The martensitic structure is formed on cooling through a critical range6

Jan 1, 1950

The roasting process of copper concentrates containing variable quantities of arsenic in a fluidized bed regime was analyzed, considering the technical literature published on the topic in the last quarter century. Although emphasis has been given to the analysis in the fluidized bed regime, other processes have also been considered, under a reducing, neutral or oxidizing atmosphere. The kinetic mechanisms of roasting, as well as the models that have been applied or those likely to be used to explain the kinetics of arsenic removal, are analyzed. Regarding the kinetic mechanisms, those that have been applied to copper concentrates with both high and low arsenic content are included. The roasting kinetic model includes the kinetic data analysis techniques, general models, equations and an estimation of the conversion degree through dynamic, differential and integral methods, as well as particular models for mineralogical components, such as smelter dust and copper concentrates with low and high arsenic content.

May 1, 2012

By Jeffrey W. Fergus, Shiqiang Hui

"Aluminum is an important alloying addition to the zinc used in the hot-dip galvanization of sheet steel to control the properties and appearance of the resulting coating. Optimization of the galvanization process requires control of the alloy concentration which can be improved through the use of chemical sensors. Aluminum sensors based on molten electrolytes are commercially available but are not widely used because of their high cost. One approach to reducing the cost is to use a solid electrolyte which can simplify the sensor design and thus reduce the cost of fabrication. In this paper, the development of an aluminum sensor based on a solid fluoride electrolyte, specifically magnesium fluoride, will be described.IntroductionThe concentration of the zinc bath used in hot-dip galvanization affects the galvanization process as well as the properties of the resulting coating. Thus, accurate in situ measurement of the alloy composition can be used to improve process control. This paper describes a solid-electrolyte-based aluminum sensor for monitoring the bath composition during hot-dip galvanization."

Jan 1, 1997

By I. I. Bethcherman

Introduction 1.-lmportance of Physical Nature of Condensates The metals of commercial interest which have reasonably high vapour pressures below 1,200° C. are mercury, cadmium, sodium, zinc, magnesium, lithium, and calcium. With the exception of mercury, these metals occupy high positions on the electrochemical series and form compounds with very high negative free-energies of formation. It is highly desirable that such metals should not be produced in a form which is finely divided, on account of their reactivity with atmospheric gases. Powders of magnesium, calcium, and even zinc (blue powder) are dangerous to handle and cannot be coalesced by simple melting techniques. Vaporization in vacuo forms a convenient method of handling and purifying the alkaline earth metals in particular and a previous paper by the authors dealt with some of the factors controlling the separation of metals by this technique (12). An essential part of the operation is the condensation of the vapour to produce a massive deposit which may be conveniently melted and handled by established metallurgical techniques. This investigation sought to determine the conditions affecting the nature of solid condensates.

Jan 1, 1951

By Rena I. Geroyan

This U.S. Bureau of Mines report presents an evaluation of the coal mining industry&apos;s impact on the economy of Pike County, KY. A software package called IMPLAN was used to perform the analysis. The results of this study show that coal mining was the primary income producing industry in Pike County in 1990, accounting for about 46% of the county&apos;s Total Industry Output, and 21% of the total employment.. Coal production in that year amounted to 29.6 M mt (32.6 M st). Two alternate economic scenarios were developed to study the potential effects of changing coal market conditions on the county. Scenario A assumes market changes result in a coal production increase of 4.5 M mt/yr (5.0 M st/yr), and scenario B assumes a decrease of 4.5 M mt/yr (5.0 M st/yr). Scenario A would result in a 15.3% rise in the value of Pike County&apos;s Total Industry Output, adding a total of 1,663 jobs (+6.1%) in all sectors in the county. Scenario B would have the opposite effect, decreasing the Total Industry Output and employment by identical amounts. Such knowledge would allow local and regional officials to anticipate the economic and social impacts of shifts in coal production, and plan accordingly to mitigate impending changes.

Jan 1, 1994

By J. A. du Plessis, C. Dorfling

Selenium, tellurium and other precious metals (OPMs, namely Rh, Ru and Ir) dissolve in the final leaching stage of base metal refineries. Se and Te are typically removed from the copper sulphate leach solution by precipitation with sulphurous acid. Recovery of dissolved OPMs is desirable because it will reduce OPM inventory and losses. Thiourea is an effective OPM precipitation reagent, but yields insufficient Te removal. Copper is known to enhance Te precipitation when using sulphurous acid as precipitation reagent. The primary objective of this project was to evaluate whether simultaneous precipitation of Se, Te and OPMs using thiourea with metallic copper as precipitation reagents is possible. Batch precipitation tests were performed to evaluate the effect of temperature (50 – 70°C), thiourea addition (160 – 430% excess) and copper addition (2 – 8 g/L) on Se, Te and OPM precipitation. Increasing the temperature from 50°C to 70°C resulted in an average increase of 55.6 percentage points for Se precipitation and 13.5 – 23.5 percentage points for OPM precipitation. The copper addition did not have a significant impact on the precipitation behaviour. Increasing the thiourea addition increased the precipitation of Se and Te, especially when the copper addition was low; Rh and Ru precipitation also increased with up to 10 and 12 percentage points, respectively. Despite these observations, the precipitation of Se was significantly faster when no thiourea was added. It is not currently clear why thiourea appears to inhibit the Se precipitation by reaction with metallic copper. In general, Te precipitation was low (less than 30%) at the conditions investigated. Simultaneous precipitation of Se, Te and OPMs at temperatures below 80°C does not appear to be a viable option; a multiple stage operation for sequential removal of Se and Te with copper followed by OPM precipitation with thiourea would be required.

Jan 1, 2016

By E. Hasanbas

Vibrating screens and crushers are the workhorses of material sizing. Unfortunately their natural frequency is often in the range of typical supporting structures, thereby making installations prone to vibration problems. Much of the available literature regarding the support of vibrating screens is fairly confusing and outdated. This paper presents the results of utilizing accelerometers and finite element software in the analysis and design of supports for vibrating equipment. It contains data from field studies of vibrating screen and crusher installations, design of new and repair of existing supporting structures, and the correlation between field data and finite element time history analyses. Finally, the paper summarizes a method for analyzing and designing structures subjected to vibratory loads and predicting their behavior.

Feb 23, 2014

By K. Winterton, Carruthers. J.

"Attempts have been made to produce hardened structures of a pseudomorphic type in various carbon and alloy steels. In order to obtain martensite with a fine distribution of cementite, an initial structure of fine lamellar or nodular pearlite is required; this may be obtained by conventional means. This is followed by partial austenitization and quenching.Two methods have been tried to induce partial austenitization:(a) A resistance (direct current) heating method involving rapid entry into the austenite field.(b) A new method, described as the ""threshold"" technique, involving homogenization of temperature just below A 1, followed by entry into the austenite field; two furnaces are required.The resulting structures have been examined for microstructures, hardness, tensile, and impact values. The tensile properties are comparable with those obtainable by conventional treatment methods. Impact values are disappointing, but this is explainable from the nature of the manifold changes occurring."

Jan 1, 1960

By R Moreby

This paper is a demonstration of the techniques developed during an Australian Coal Association Research Program (ACARP) funded research project aimed to develop aids, principally computer based, to assist mine personnel to more efficiently manage significant incidents in coal mines. These aids include software to aid in the location of the incident, electronic information storage and retrieval, online site emergency response manuals and software to aid in decision-making.

Jan 1, 2005

Safety remains a critical priority for the Australian mineral resource industry and will receive increased focus in the future. This is particularly evident in underground coal mines where reserves are becoming deeper and more hazardous to extract. The CSIRO, through its Exploration and Mining Division, have recently delivered on two projects aimed at providing step-change capabilities in real-time risk management and hazard control. This paper describes the key outcomes of these projects.

Jan 1, 2005

By M. Yao, D. Thibodeau

"Selective mining, such as post pillar cut and fill, is used in large, flat, irregularly shaped ore bodies where ground stability is to be maintained. This selective mining is used to open the stope to the full lateral extent of the ore body in order to minimize the dilution and maximise the recovery. For increased mining depth, design of the post pillar becomes more challenging since those pillars will eventually fail as mining progresses upwards. The post pillar should be designed such that failure does not occur at the early mining stage, such as at the first cut. After mining progresses upwards, the post pillars are expected to fail but be confined by backfill. In order to maximise ore recovery, both drift width and post pillar size must be designed adequately with a consideration of all geomechanic parameters. This paper will describe the process used to design post-pillar cut and fill for one of the ore bodies in Vale’s Copper Cliff Mine using a combination of both empirical deterministic and numerical modelling techniques. By utilizing both empirical deterministic and numerical modelling techniques drift width and post pillar size can be effectively designed. Current post pillar cut and fill design in the existing Vale operations are used to validate the design for Copper Cliff Mine. INTRODUCTIONCopper Cliff Mine is located within the Copper Cliff Offset in the limits of City of Greater Sudbury, Ontario, Canada, as shown in Figure 1. The Copper Cliff Offset extends about eight kilometres south from the Sudbury Igneous Complex into the footwall rocks. Until 2008, the current Copper Cliff Mine was operated as two separate mines i.e. North Mine and South Mine. However, as part of restructuring of Vale Ontario Operations, the North and South Mines were merged in 2009 to form the “Copper Cliff Mine”."

Jan 1, 2015

By T. E. W. Nind

"A short description of the chamber lift method for producing oil wells is followed by some comments on compressor requirements and gas utilization. A quantitative analysis of the process is presented and, based on this analysis, criteria are suggested for selecting wells for which this type of lift might be suitable. The analysis leads to the conclusions that chamber lift is an efficient producing mechanism for wells having very low productivity indices (say about 0.05 bbl/d/ p.s.i. or less), but that for such wells optimum utilization of injection gas cannot be attained. It is suggested that the gas injection time per cycle should be kept as low as possible, compatible with a small oil fallback volume, and that the cycle frequency should be in the range of 20-40 cycles/ day. For wells with productivity indices of 0.2 bbl/d/p.s.i. or higher, chamber lift is relatively inefficient; how-ever, if well allowables are low it may offer an attractive, low cost, alternative to gas lift or pumping."

Jan 1, 1960

"ALTHOUGH Canadian metallurgists have long been active in research, the scope of the work was somewhat limited until the be-ginning -of World War II. The rapid industrial development of Canada during the past ten years has been accompanied by .a similar upsurge in research. However, the wide geographical distribution of the research centres has made it difficult for the individual research workers to meet together and to exchange ideas or even to learn what projects .are being investigated or the nature and extent of the facilities available for work of this kind.The purpose of the present symposium is to assemble data relating to projects under investigation and the facilities employed at the various metallurgical research laboratories in Canada, thus providing some measure of correlation so that workers in different locations may learn what kind of work •is being .done at other points throughout the country.In reporting the symposium it has not been possible to reproduce the papers in full, but excerpts have been selected that give the essentia1 data."

Jan 1, 1952

By Emilie Williams

Introduction Mouska Mine, Doyon Division site Background and timeline Obstacles to standard paste delivery system Components of Mouska paste system Technical considerations Operational considerations Mouska Mine Underground gold mine 30 km east of Rouyn-Noranda, Quebec Part of Doyon Division, 100% owned by IAMGold Commercial production since 1991 Cumulative production over 850,000 oz Conventional mining until 2009 485 m shaft from surface 560 m internal shaft 500 tpd (ore and waste) Off-site milling Approximately 150 employees

Oct 1, 2010

This information circular describes research the Bureau of fines has conducted to improve technology for recovering precious metals from low-grade resources. Many of the reported findings are recent, and some of the work described is ongoing. Topics discussed include cyanidation of carbonaceous gold ores to enhance gold recovery, a new method for precipitating mercury during cyanide leaching of gold ores, a staged heap leaching process to generate suitable solutions for direct electrowinning of gold, the use of anion-exchange resins to recover gold from cyanide solutions, and precious metals recovery from electronic scrap.

Jan 1, 1986

By G. W. Evatt

This paper presents the scientific framework underpinning the Resource Valuation and Optimisation Model (RVOM). The RVOM is a Real Options software package, which helps mine owners optimally plan their operations, understand their project risks, and make defensible valuations. This is achieved in the presence of both financial and physical uncertainty. The three key outputs from the RVOM are: Valuation, Optimal Decision and Probability of Decision, where a decision can include any combination of: normal operation, expanded operation, care and maintenance, and abandonment (and variants thereof). This paper presents a clear example of the RVOMs usage to a case-study gold mine.

Jan 1, 2011

By S. Klingmann

ABSTRACT In this paper, we used data collected from the Gibraltar mine to analyze the effect of the TyreSense tire monitoring system on tire performance by reducing tire wear and preventing premature tire failure or damage. We analyzed the relationship between tire temperature, tire pressure, and tire failure or damage to help better understand the importance of controlling high tire temperature and pressure. The results enhance and expand the knowledge of the management of tire operational pressure and temperature.

Jan 1, 2014

By C. R. DeGennaro, Yongjun Zhang, J. Bickson, J. L. Carr, Chenming Zhou, J. R. Srednicki, B. Lambie, M. Girman, J. A. Galanko

Between 2005 and 2021, surface mining haul trucks were involved in 54 fatal incidents in the United States [1]. Collision warning and avoidance systems (CXS) can help haul truck operators navigate their route safely. The evaluation of CXS object detection performance for surface mining haul trucks relies on the positional accuracy of the ground truth instrument. As part of a holistic approach, researchers from the National Institute for Occupational Safety and Health (NIOSH) characterized the accuracy of a global navigation satellite system (GNSS) that serves as the ground truth instrument to determine object position and velocity in CXS object detection performance testing. We used precision surveying equipment to establish ground truth points for comparison with GNSS data collected for static positional measurements and reduced-scale straightline vehicle dynamic tests. We conducted these tests with real-time kinematics (RTK) and then satellite-based augmentation systems (SBAS). For the dynamic tests, we measured a distance error of 1.34 m (4.40 ft) using RTK and 1.50 m (4.92 ft) using an SBAS. This research will provide CXS manufacturers and CXS researchers a basis for evaluating the positional accuracy of CXS. Note that we did not evaluate any CXS in this experiment.

Feb 1, 2024

By E. C. Lane

For a number of years the Bureau of Mines has been studying crude petroleum from the producing fields of the United States, During the past year 10 crude-oil samples have been collected and analyzed from the producing fields of Pennsylvania and New York. This report gives the results of these analyses and for the purpose of comparison also analyses of samples of crude oils taken previously from some of these fields. This survey includes samples from normal producing properties as well as from properties using stimulative production methods such as water flooding and rapressuring. The outstanding feature of the survey is that the crude oils from tike various fields throughout this general area are similar in character and uniform in quality although they were produced from different sands and by various methods. Samples from fields in Venango County, Pa., however, appear to have a lower gasoline content than the others. This report includes two analyses reprinted from Bureau of Mines Bulletin 291.4/

Jan 1, 1938