Search Documents

By B. A. Eaton

The subject of many discussions and technical papers in the last 20 years has been the prediction of the well-bore pressure gradients that are required to induce or extend fractures in subsurface formations. The subject merits this attention because of the frequently recurring problems that arise from an inability to predict fracture pressure gradients. Encountered in several common types of operations in the oil industry are problems associated with the prediction of formation fracture pressure gradients. When wells are being drilled in both new and old fields, lost circulation is often a very troublesome and expensive problem. Complete loss of circulation has been disastrous in some cases. Many times, such disasters could have been avoided if techniques for calculating fracture pressure gradient had been employed in the well plans, and if casing strings had been set, and mud weight plans had been followed accordingly. In areas of abnormally pressured formations, the prediction of fracture gradients during the well-planning stage is extremely important. In fact, it is as important as the prediction of formation pressure gradients, which has received a great deal of attention in recent years. There are several published methods used to determine fracture pressure gradients. However, none of these methods appears to be general enough to be used with much reliability in all areas. In 1957, Hub-bert and Willis published a classical paper that included the development of an equation used to predict the fracture extension pressure gradient in areas of incipient normal fau1ting.l Overburden stress gradient, formation pore pressure gradient and Poisson's ratio of rocks were the independent variables that were shown to control fracture pressure gradient, the dependent variable. In 1967, Matthews and Kelly published another fracture pressure gradient equation that is different from that of Hubbert and Willis in that a variable "matrix stress coefficient" concept was utilized.3 Later the same year, Costley wrote about a similar idea.5 Goldsmith and Wilson used a least-squares curve-fitting technique and field data from the Gulf Coast area to correlate fracture pressure gradient with formation pore pressure gradient and formation depth.' They noted that the fracture pressure gradient increased with increasing depth while the pore pressure gradient remained constant. In each of these cases, the problem for which a solution was sought was to determine the bottom-hole pressure gradient required to initiate or extend a fracture. Results of the previous work show that fracture pressure gradient is a function primarily of overburden stress gradient, pore pressure gradient, and the ratio of horizontal to vertical stress. There is argument for a fourth variable in that in many cases breakdown fracture pressure gradient is greater than the fracture extension pressure gradient. However, if the fracturing fluid is able to penetrate the formation through the pores or existing cracks, there is very little

Jan 1, 1970

By R. L. Guerguerian

Nowadays, most grinding mills driven by a wrap-around ring motor are operating successfully. Some of the earlier problems could be attributed to the lateral stiffness and stability of their bearings. As a result, modifications to the bearings included the rearrangement of the shoes, or the addition of more shoes, closer to the horizontal centerline. This technical paper reports a study of the effects of bearings on the lateral stiffness of grinding mills driven by a wrap-around ring motor. The discussions cover the design of the four shoe trunnion bearings and examine the effects of the angular location of the shoes.

Jan 1, 2000

The key to the successful debt funding of a new mining project, whether in economically established or developing nations, is the submission of a comprehensive feasibility study. The feasibility study forms the basis from which the resource banker can construct financial models which govern the amount of available funds, the conditions which control the supply of such funds and the time period over which the loan may be repaid. The bank will wish to ensure that the feasibility study is the best representation and confirmation of reality possible because this model is the basis of the loan security package. Thus the study will be vigorously interrogated by independent experts in all its elements including the ore reserve, mineability, metallurgy, operating and capital cost profile, environmental factors and management. A well constructed feasibility study, undertaken by well recognised and respected independent consultants can save the client company a great deal of real and opportunity costs especially in relation to project timing. Once constructed and operating, the mining project may face one or more completion tests in relation to the loans provided. The genetics of such tests often relate to either the ability of the operating company to become solely responsible for the repayment of the loan or to be rewarded by lower interest rates or some other mechanism. Strong professionalism, accessible records, good checking procedures and high quality, competent site management will greatly assist the client company passing these tests. A record of well established technical competence with its bankers may well assist a company in the establishment of a mezzanine loan for the early development of its next project, thus allowing an earlier return of dividends to shareholders.

Jan 1, 1995

By G. L. Mowrey, S. D. Maksimovic

An important element of the U.S. Bureau of Mines (USBM) mining research program is the development and evaluation of reliable coal interface detection (CID) systems. Commercially available CID sensors based on natural gamma radiation (NGR) are only applicable if the immediate roof is composed of shaley material. The USBM has made numerous underground and laboratory measurements using several NGR systems approved for installation on mining machines by the Mine Safety and Health Administration. In addition, two small handheld NGR instruments were used to make comparative measurements. Underground NGR measurements in 10 different coal seams, potassium-uranium-thorium radiometric analyses on samples from 16 seams, and chemical analyses of coal and rock for correlation with NGR counts were made. Laboratory test results on the effect of air gap and sample thickness, size, and weight on the NGR measurements, as well as general results of the various NGR systems, are discussed.

Jan 1, 1995

By M. L. Goble

"Inco Metals Ltd. (Manitoba Division) operates a mining, milling, smelting and refining complex, 500 miles north of Winnipeg in central Manitoba. The Thompson Mill is presently operating at 12,000 S.T.P.D. on ore from both underground and open pit mines. The ore is treated in two separate milling and flotation circuits utilizing a common crushing system which is located inside the main mill building. The milling facility employs approximately 43 operating employees, 30 maintenance employees and 20 staff in supervisory or process development roles.In recent years an increasing awareness of the potential hazards of contaminants in the work place has made it mandatory that all employers maintain careful and accurate records of the work environment to which each employee has been exposed during his working career.The importance of this record keeping and general observation of the work place cannot be over emphasized. Proper monitoring of the work place provides an accurate and complete record of the contaminants and physical agents to which an employee is exposed during his work career. This can aid in studies which might be conducted in the future and can also be used as a basis for instituting improvements to the workplace."

Jan 1, 1980

By S. Kelebek, J. A. Finch, Zhenghe Xu, S. R. (Ram) Rao

To improve SO2 emission compliance, pyrrhotite from Sudbury copper-nickel ores is being depressed with DETA. To understand the mechanism of depression, the role of complexing in controlling metal-ion activation of pyrrhotite was investigated. DETA was found to remove Cu and Ni ions but leave hydrophilic ferric species on the pyrrhotite surface. The metal:DETA ratio appeared to be 1:2. Cu was more readily removed than Ni, but the combination of DETA with sulphur dioxide was equally effective for both metal ions. Certain combinations of DETA, Ni ions, xanthate and dithionite (S2O4) or dithionate (S2O6), as representative derivatives of SO2 in water, produced hydrophilic precipitates. These may enhance pyrrhotite depression

Jun 19, 1905

By Campbell Brown GA

IN 1904-5 diamond drilling operations in the Mount Morgan mine proved the presence of some inillioils of tons of rich, copper-gold ore, averaging about 45% to 50% silica and 22%Fe as sulphide. To smelt this ore in blast furnaces, without previous concentration, large quantities of basic flux.were required. Unlimited quantities of cheap, limestone, were available at Marmor, on the GladstoneRockhampton railway, 50 miles from Mount Morgan, but the supply of iron flux was a more difficult problem. Smelting operations started, with one' furnace in January, 1906, using as flux low-grade sulphide ore fro:m. the mine, containing very little silica. When the second, furnace was blown in this was supplemented by ironstone from, small aeposits in the immediate district. It was recognized that these sources of supply would be insufficient to keep the full plant going after the third furnace had been blown in. Accordingly, the deposits at Eabra and Mount Etna were opened, neither of which proved capable of supplying the quantity required viz, 1000 tons per week. Negotiations were meanwhile being conducted with the Marble Island Iron and Limestone Co. to obtain the right to mine at Iron Island, where a sufficiently large deposit was known to exist. Shipments from this source commenced in January, 1907, and ceased at the end of July of this year, when the metallic flux from...

Jan 1, 1912

By M. J. Beus, B. Stewart, S. Iverson

Synopsis U.S. Mine Safety and Health Administration (MSHA) accidents statistics have identified ore-pass hazards as a significant safety problem in U.S. underground metal mines. The statistics show that nearly 75% of injuries are directly or indirectly related to pulling or freeing of ore-pass chutes, the use of hand tools in ore passes, fails of broken rock in ore passes and structural failures of chutes or gates and ore-pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines. Risk assessment methods, such as fault-tree analysis, have been employed to identify the most probable causes of orepass failures, define research priorities and analyse the factors that result in malfunctioning and unsafe ore passes. Static and dynamic loads are being measured in a laboratory setting with the use of a reduced-scale orepass mock-up. Field tests are being initiated in mine ore passes to determine static and dynamic loads. Data from the test ore passes are being compared with data from the mine to characterize true system behaviour. Computer modelling with the use of closed-form solutions, finite-element analyses and a newly developed particle flow code predicts static and dynamic leads from the flow and the impact of ore and waste in the ore pass. Preliminary results indicate that dynamic impacts from ore and waste rock might be considerably greater than expected. The total static load is substantially less than is typically used fur the structural design of chute and gate support members. It is suggested that damping factors, normal and shear stiffness and mass frictional characteristics have a significant effect on particle flow and resulting impact loads. This is being verified with the use of results from laboratory tests, field tests and particle flow analyses. Ore passes are vertical or steeply inclined openings in a rock mass through which ore and waste are transported and where they mar also be stored. A typical underground mining system is shown in Fig. 1. The arrows indicate the locations of ore passes and loading pockets and their relative configurations. The control of material flow is potentially one of the most hazardous operations in underground mining. According to MSHA data. most of the ore pass-related accidents in the U.S.A. are associated with the loading-unloading cycle and removal of blockages from ore passes. In particular, attempts to free ore hang-ups have resulted in multiple fatalities. The hazards are obvious; there is uncertainty as to when the ore will break loose and miners are unable to escape falling rock to a safe location. Although ore passes and chutes and gate systems for underground metal and non-metal mines roust meet the requirements specified in the U.S. Code of Federal Regulations (CFR). Parts 57 and 75, recent structural failures of ore-pass linings and gates have underlined the lack of adequate ore-pass design standards available to both MSHA enforcement staff and mine engineers. Because of the importance of an ore pass to the safe operation of a mine design criteria need to be assessed and new guidelines developed. Researchers at the Spokane Research Laboratory of the Nationals Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines and studying design criteria for ore passes. The near-term goal is to conduct laboratory and field experiments and computer modelling to evaluate the ore-pass design criteria currently used. Literature searches, field site

By John A. Owsiany

The effect of longwall mining on streams and shallow aquifers has been the subject of numerous research studies for more than twenty years. As a result of these studies, it has become common to consider an overburden thickness of 400 feet as the lower limit at which longwall mining methods may be used with little or no effect on hydrologic systems. This paper presents the results of a study documenting the response of a large high order stream to shallow cover undermining by longwall methods in the northern Appalachian coalfield. The field site is located in a narrow stream valley where the overburden, composed primarily of limestone and sandstone units interbedded with shales and siltstones, ranges in thickness from 340 to 285 feet above the main bench of the Pittsburgh coal seam. Streamflow monitoring and monitor well measurements indicate that no significant loss zones or water table lowering resulted from undermining the stream or the adjacent valley bottom area. Additionally, hydrographs for shallow near-stream wells exhibit fluctuations related to natural seasonal variations, which are nearly identical to those observed in a non-undermined control well in the same watershed. Environmental factors affecting streamflow were monitored through the use of a control stream in an adjacent non-undermined watershed to differentiate between natural and mining induced changes in flow.

Jan 1, 2001

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008 ? ?I guess that without the occasional complaint, your mine is probably over-ventilated? (Marks, 2008). Miners are seldom in this situation and often spend much of the time trying to find enough air to keep the operation running. With examination there are some things that can be done to make the best use of ventilation systems. Should there be surplus air, in which some of these options may result - financial and other benefits can be obtained. Some of the issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and non-metal mines. Also, operations are faced with demands from reserves that are deeper, hotter and further away from fans and shafts, not to mention increased production demands. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Most of the options presented in this paper are useful for metal non-metal operations but some may be applicable to coal too. OPTIONS FOR IMPROVEMENT Some of the areas to be addressed are shop ventilation methods, auxiliary equipment areas, dedicated intakes and returns, optimizing development, examination of mine airway utilization and alternative ventilation methods. UNDERGROUND SHOPS First, examine what is being done with the underground shop air. If it is being coursed directly to the returns there may be some potential to better utilize this, in most cases, relatively contaminant free air. Research the legal options for ventilating mine shops. MSHA regulations in 30CFR 57.4761 (1) allow the following options: To confine or prevent the spread of toxic gases from a fire originating in an underground shop where maintenance work is routinely done on mobile equipment, one of the following measures shall be taken: use of control doors or bulkheads, routing of the mine shop air directly to an exhaust system, reversal of mechanical ventilation, or use of an automatic fire suppression system in conjunction with an alternate escape route. The alternative used shall at all times provide at least the same degree of safety as control doors or bulkheads. Discussion This regulation gives some operators flexibility in ventilating underground shop facilities. If shop air is to be coursed through the work area, and then directly to the mine return, the question should be asked ? is the quality of air good enough to be reused in the mine, and if so, what are the risks? Can the risks be accommodated and managed to accomplish the change? If so, a considerable increase in mine level airflow could be attained by reusing shop air. Clearly, regulations are a minimum standard, and can be exceeded. Metal non-metal mine regulations are not as specific as coal due to the multitude of different mining methods and conditions utilized. Risks must be thoroughly examined and addressed to assure a safe environment. Issues Determine what contaminants are being produced in the work area ? welding fumes, diesel exhaust, paint fumes, chemicals and solvents, etc. Survey the area and determine exposures. MSHA requires exposure monitoring in 30 CFR 57.5002 (1) of dust, gasses mists and fumes to assure air quality is being met. Perform surveys and examine existing data to quantify personal and area concentrations of contaminants. Often there is adequate circulation such that exposure levels in shop work areas are low. After sending shop air back into the system any contaminants would be further lowered by dilution with other mine intake air downstream. Look at the shop work schedule. If only on day shift, the other two shifts and possibly weekends have no activity or source of contamination to affect the ventilation system. The worst case planning scenario would be a shop fire. Study and simulate how this would affect the mine and shop area. MSHA regulations require an escape route and a fire suppression system be installed and maintained as follows in 30 CFR 57.4671 (1): (d) Automatic fire suppression system and escape route. If used as an alternative, the automatic fire suppression system and alternate escape route shall meet the following requirements: (1) The suppression system shall be? (d)(1)(i) Located in the shop area; (d)(1)(ii) The appropriate size and type for the particular fire hazards involved; and (d)(1)(iii) Inspected at weekly intervals and properly maintained. (2) The escape route shall bypass the shop area so that the route will not be affected by a fire in the shop area. Case Study In an underground room and pillar mine, active mine workings were advancing further away from the mine shaft with deteriorated returns and leakage having a negative effect on ventilation airflows to the face. Mine level airflows were 236 m3/s (500,000 cfm) and shop airflows were 24 m3/s (50,000 cfm) (see Figure 1A). No additional capacity was available at the main surface fan. A solution was to utilize the shop air then send it to the mine areas instead of directly to the return. Considerable information on shop air quality and exposures from many years of operation was examined and no negative data was discovered. A risk analysis determined that moving forward with a shop air reuse program was desirable. A plan was developed, analyzed and decision to proceed approved by mine management. The change was simulated on the computer with the USBM/MTU MFire program before being implemented. This included utilizing fire scenarios to examine potential exposures to inby mining sections and plan escape routes. A monitoring system was designed and installed in cooperation with the US Bureau of Mines to monitor carbon monoxide

Jan 1, 2009

ONE DAY IN the mid-1880s, in a suburb 0f Pittsburgh, Pennsylvania, there dismounted from a train the two foremost leaders of the day in the coal and steel industries-Andrew Carnegie and H. C. Frick. Their attention was drawn to a well-loaded car of coke, which their experienced eyes recognized as a superior product. "I'll bet you that coke is from the H. C. Frick Coke Company," Mr. Frick challenged. "I'll bet it was shipped by my company." In a spirit of fun Mr. Carnegie accepted the wager. Mr. Frick lost the bet: the coke had come from M0rewood, one of three sites being operated under the direction of a young entrepreneur, Erskine Ramsay. If Mr. Frick's confidence was somewhat dented by this occurrence, the responsibility was his own. He himself had opened the way for Erskine Ramsay to become the youngest of mine superintendents; and he had dispersed all dissension regarding his choice with the words : "I'm not interested in his years, I'm interested in his record. He makes more coke in an oven than any other superintendent. And I'll take 'em out 0f the cradle if they can make coke... Suppose he is only twenty years old? ... The d --- kid is a genius, I tell you." Erskine Ramsay was to follow in the tradition of Carnegie and Frick. Not only was he ambitious and a worker his background had prepared him for it. Coal mining was in the Ramsay blood. His father, Robert Ramsay, of whom the son once stated that he had no superior as coal mining and mechanical engineer in this country, once accounted in these words for the phenomenal accomplishments which had attached to the name "It does no harm to belong to a family of mining engineers who are just as good as any in America-if it is myself that says it." Anyone acquainted with Robert Ramsay's character realized that he was not given to overstatement. And the above-mentioned Mr. Carnegie encountered young Ramsay again, a few years later in his career, and wrote of him to young Erskine's father, that he was "going to be a credit `tae us a' " (a quotation from Robert Burns.) Nor have Mr. Ramsay's achievements been identified exclusively with the industrial field in which he early asserted himself. He has been an inventor whose techniques in mining engineering have received international recognition. As an investor of foresight, he has benefitted others immeasurably, as well as himself, being an influential factor in the upbuilding of several communities in his chosen and well-loved adopted home state of Alabama since 1887. He is a philanthropist whose benefactions have run into millions, the chief beneficiaries being educational and charitable institutions. Amidst his accomplishments the lighter side of life has not been neglected and he is known for his hospitality, his

Jan 1, 1953

By Kenneth G. Skinner

The rapid growth of the metallurgical, chemical, and allied industries on the Pacific coast just prior to and during the war caused a sudden increase in the demand for refractories, which was the immediate cause of a revival in interest in refractory clays available on the Pacific coast, particularly in the Pacific Northwest. Population increases and shortage of shipping facilities caused an increase in the amount of various ceramic materials and products used and produced on the Pacific coast, with accompanying demand for information regarding sources of clay. In an effort to supply part of this information, the Bureau of Mines, in cooperation with the College of Mines, University of Washington, started a program in 1944 to test the refractory and other properties of clays from seven Pacific Northwest deposits that had been drilled and sampled as part of the Bureau of Mines alumina from clay investigation. Figure 1 shows the location of these deposits.

Jan 1, 1949

By M. K. Eryadin, I. Yildirim, R. Asmatulu

Novel dewatering aids were tested on various coal samples from the U.S. and Canada in laboratory and pilot-scale filtration experiments. The reagents substantially improved the dewatering kinetics and reduced the cake moistures. The cake moistures were typically reduced from 20-30% by weight to 8-14% range in vacuum filtration. When the reagents were used in conjunction with a pressure filter, higher degrees of moisture reductions were achieved. In the present work, the novel dewatering aids were tested using different types of pilot-scale vacuum filters. The results were consistent with those obtained in laboratory experiments.

Jan 1, 2003

By Frederic P. Dewey

THE Bureau of the Mint of the United States Treasury maintains 13 offices for the purchase of gold-bullion, and this paper describes an investigation to establish the reasonable differences in the assay-results at the various institutions which may be commercially allowable in the settlements between them. Beginning with the comparative assay of proof-gold at the Philadelphia mint and the Utrecht mint, which shows 0.00002 as the closest agreement now possible, eight tables of comparative results, taken from the regular work of the service, are given. These tables begin with very fine gold, produced in an electrolytic refinery, showing close agreement. in the assay-results, and follow through decreasing gold fineness and . increasing amounts and complexity of base metals to very impure and complex bars produced at cyanide-mills, some of which give widely-varying results. Next is given a series of results on samples, prepared and sent out to various laboratories in the service, to test the influence of different metals and various combinations upon the' agreement of the assay-results; 11 samples were sent out and each one was assayed from 44 to 71 times, making a total of 623 assays. To these are added 107 assays of identical samples of coin-gold. On a previous occasion,' I have endeavored to show the degree of accuracy that may be expected in the ordinary everyday analysis of various materials, and on another occasion2 I

Aug 1, 1909

By Mann V. I

The Mount Isa property has been in operation since June, 1931; during this period operations have changed from the production and treatment of carbonate ores to the mining, milling, and smelting of sulphide ores. This change involved revision of ore-extraction methods.Stoping methods have been designed to apply to parallel lodes ranging from 10 ft. to over 100 ft. in width and dipping at 50° to 60°. The hardness and strength of the ore and enclosing wall rocks, together with the strength and thickness of the country rock between lodes, have permitted the selection of a sub-level stoping method for mining the sulphide ores.

Jan 1, 1938

By E. P. Deliac

The aim of this joint work between the French Coal Board and the Paris School of Mines is to be able to practically model the behaviour of a transverse drum cutting rock with picks. First a theoretical approach leads to the concept of cutting curves, giving forces and torque against penetration per drum revolution. Then experimental evidence, from full scale and reduced scale testing, validated and confirmed the theoretical shape of the curves. Finally practical applications are given, to improve the design or use of a shearer (or continuous miner). A micro-computer program is being developed to predict the cutting performances of a machine in certain conditions.

Jan 1, 1985

Experiments in the bolting of a mine roof were commenced at Elrington Colliery on the South Maitland Coal Field early in 1949, following the appearance of an article in the American publication, "Coal Mine Modernisation Year Book" 1948. Prior to this, although bolting had not been used in the maintenance of satisfactory roof conditions, the principle of roof bolt anchorage had been illustrated in instances such as the hanging of a trolley locomotive power wire using an expanding shell type of bolt anchorage, or the insertion of an eye bolt with a split and wedge, as used to suspend a rope block over a winze being sunk in a metalliferous mine.The experiments at Elrington Colliery were the first efforts in this country to supplement the work of timber supports under a mine roof with systematic placement of roof bolts.Following the series of experiments at Elrington, full scale bolting was commenced at that Colliery in a trackless mobile section in April, 1950.The obvious success of the system at Elrington indicated that it might also be a success in the support of weak roof strata immediately overlying the workable section of the Victoria Tunnel Seam at John Darling Colliery.The system was commenced at John Darling Colliery in April, 1951, in one mechanical section on the Victoria Tunnel Seam, and the scope was gradually widened until by December, 1952, ail'six mechanical units then operating on this seam were working under bolted roofs.

Jan 1, 1954

By Laura McNally

In 2006, McNally International Inc., in a joint venture partner-ship with Aecon Constructors, was the successful bidder on two York Region Tunnel Projects: the Bathurst Collector/Langstaff Trunk Sewers and the York Durham Sewer System (YDSS) Interceptor Sewer 19th Avenue, both in the Toronto area. These projects comprised a total of 13 km (8 miles) of 2.74 m (9 ft) finished diameter tunnels and are both part of the YDSS. Both contracts required the use of earth pressure balance (EPB) tunnel boring machines (TBM) with a precast concrete segmental liner.

Jan 1, 2008

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin, Derek Maishman

Ground freezing was utilized to provide complete stability of the excavation face and complete groundwater cut-off for the jacking of the three tunnel boxes for the Interstate 90 / Interstate 93 approach to the Fort Point Channel crossing. Through a wide range of geological conditions and large buried obstructions, the freezing provided complete stability of the face so that a 11.5 m (38 ft) high free standing vertical face could be mined without the need for any additional face support. Obstructions were incorporated into the massive frozen ground matrix, and held in place so that they could be excavated with a minimum of disturbance. The freezing provided an absolute groundwater cut-off, and permitted the work to be done without disturbance to the active rail system immediately above. With the use of instrumentation such as borehole thermocouples, the effectiveness of the freezing was guaranteed and the jacking proceeded with complete confidence and assurance of the ground conditions ahead.

Jan 1, 2001

By C. A. Geffen

This report, sponsored by the U. S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the com¬ponent operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982