Search Documents

By K. J. Liles

This Bureau of Mines paper describes the composition and properties of drilling fluids for use in high-temperature geothermal wells, and summarizes the problems encountered with fluid use at the known major geothermal sites throughout the world. These include the western continental United States, Hawaii, Italy, Iceland, Japan, New Zealand, and Turkey. Water-base drilling fluids of 9- to 10-lb/gal weights are relied on primarily for geothermal well use, although air drilling is sometimes used. Bentonite-lignite-water systems have been used most often, and additives such as polyacrylates, lignosulfonates, and chromates are employed to improve the properties of the basic system.

Jan 1, 1976

By T Kojovic, S J. Windle, J Sullivan

"The Geometallurgical Mapping and Mine Modelling (GeM) comminution index (CI) was developed as part of the AMIRA P843 GeMIII project. Drill core geochemistry samples were passed through a Boyd Crusher with standardised settings and the resulting particle size distribution (PSD) was measured using sieves.Disadvantages of the original measurement were the relatively coarse crush size, requiring a second pass of crushing for geochemical sample preparation, and the limitation of throughput caused by the sieving step. At Antamina, the measurement has been modified to use a 2.2 mm crusher size setting, which permits a single pass. The PSD is measured using a Camsizer, an automated optical sizing instrument. The Camsizer sample is a +180 µm fraction, used to avoid passing too many fines through the instrument and slowing down the measurement. In the sieving step, the weights of the two fractions are recorded and subsequently used to normalise the distribution measured by the Camsizer. In this way, the throughput of the Camsizer can match that of the Boyd Crusher. The PSD data are therefore measured without penalising the throughput of the sample laboratory.The normalised PSD distributions are used to derive modified CI parameters, based on the slope and intercept of the breakage product size distribution, which are indirect measures of the material breakage hardness.Fifty samples were selected as a training set, each sample a composite of five or six individual assay intervals and each with its own measured CI. The average PSDs were calculated for the composites and used to calculate a composite CI. The intact half of the core, approximately 40 kg, was tested to measure the BWi, A*b and crushability. The results were used to develop predictive algorithms for these hardness parameters.A further 50 composites were chosen for lab testing, to serve as a blind test of the algorithms. The paper reports on the test results and the incorporation of the modified CI data and predicted hardness parameters into the Antamina block model.CITATION:Windle, S J, Kojovic, T and Sullivan, J, 2016. Use of a Modified Comminution Index to Predict Bond Work Index and SMC A*b at the Antamina Mine, Peru, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 153–160 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Y. P. Lu

PET/kaolin nanocomposites were prepared with melt blending and the structure of the composites was characterized through IR techniques. The results showed that there is stable chemical bonding between PET and kaolin. In addition, the dispersion condition of nanokaolin was observed by means of SEM and TEM. As a result, the thickness of the dispersed nanokaolin particles in PET matrix is mainly from 20mm to 200nm, and the nanosized particles congregate to some extent in the samples. In addition, it was found the kaolin particles almost homogeneously dispersed in the PET matrix, without preferential orientation because of the shear effect due to melt blending. Furthermore, the mechanical properties of PET/kaolin nanocomposites are dependent on the modification efficiency of nanokaolin. With the poor efficiency, the nanokaolin particles tend to aggregate at a high content and have a bad interfacial compability between nanokaolin and PET matrix, which lead to stress concentration, so the mechanical property descends. Experiments of different contents of modified nanokalin indicated that the intensity of PET/kaolin nanocomposites decreased firstly, then increased, and then decreased, with the nanokaolin content of 4 to 5 percent, the rupture stress of the composites showed a maximum value, which was higher than that of pure PET. On one hand, nanokaolin decreases the function among PET macromolecules, which will decline the mechanical properties, on the other hand, the piece structure of kaolinite improves the intensity of the nanocomposite. When the nanokaolin content is low, the former has the dominant effect on mechanical property, while the latter will play a leading role with the content increasing. But if the nanokaolin content still increases, the agglomeration and stress concentration will be obvious.

Jan 1, 2014

By M. B. Royer

Sulfur is present in many ores and other raw materials that are used in the production of metals and alloys of industrial importance. Its presence, especially in ferrous-metal products, generally is undesirable because of its detrimental effect during processing and upon various physical properties of the finished metal. Therefore, various methods are resorted to for elimination of the element to some specified maximum final content. Such removal or elimination of sulfur is designated as desulfurization.

Jan 1, 1948

By Richard Hamburger

Calculating machines permit the use of the more rapid cotangent and semigraphic solutions of plane triangulation. The results of these methods are as accurate as those of other methods. Simple adjustment of the net, and ease of calculation encourage more complete field work. Errors in field work or in computation are easily localized.

Jan 1, 1950

By Avishan Atrafi, Marek Pawlik

"Gas dispersion properties of sodium salts of 6, 12 and 18-carbon fatty acids (hexanoic, lauric and oleic acid) were investigated as a function of pH. A strong effect of pH was observed on gas dispersion properties of fatty acids. At high pH for 12 and 18 carbon fatty acids, at which these surfactants formed a true solution, the gas dispersion properties were similar to those of MIBC. In the case of sodium hexanoate, which has a much higher solubility than the longer chain fatty acids and therefore does not form precipitates, the gas dispersion properties of this surfactant were strongly enhanced in the acidic pH range, where hexanoic acid was fully associated. This result is an indication that undissociated hexanoic acid is much more surface-active than anionic hexanoate. Only a small effect of the surfactant chain length on gas dispersion properties of the tested reagents was observed. The measured critical coalescence concentration (CCC95) values increase slightly by decreasing chain length and range from 5.8 x 10-5 mol/L (17.7 mg/L) for sodium oleate to 7.2 x 10-5 mol/L (16 mg/L) for sodium laurate at pH 10 and 1.9 x 10-4 mol/L (26 mg/L) for sodium hexanoate at pH 3.7. These are compared to CCC95 of MIBC, which is measured to be 8 x 10-5 mol/L (8 mg/L). The soluble molecular species were recognized as the most effective species in preventing bubble coalescence."

Jan 1, 2014

By R. C. A. Thurston

Introduction A mechanical spring has been .defined by Wahl ( 1) as 'an elastic body whose ?primary function is? to deflect or distort under load, and which recovers its original shape when released after being distorted'. Most material bodies are elastic to some extent ? and will deform under load, but they are seldom regarded as springs since this is not their primary function. The principal applications of springs are the absorption of energy and the mitigation of shock, the support cf moving masses or the isolation of vibration, and the provision or measurement of definite loads or torques. A large number of spring types have been developed to serve these purposes and to meet the different operational requirements; they range from the large semi-elliptic leaf suspension spring to the delicate watch hairspring. The springs of most importance in machine design, however, are the helical round-wire compression or tension types. They are made in a wide variety of sizes and are used in tremendous quantities, mainly because of their low cost, their compactness, and their relatively high efficiency. Their field of application is as broad as that of machine design itself, but the bulk of production is almost certainly for suspension systems of vehicles such as automobiles, freight and passenger cars, and mine cars, and it is with the last of these applications that this paper is primarily concerned.

Jan 1, 1951

By J. O. Stephens

During the late 1940's and early 1950?s, the Westinghouse Combustion Turbine Division built and demonstrated a residual oil-burning locomotive on six eastern railroads. Plans were made to convert to burning pulverized coal, and a single combustor was operated at a full-pressure condition in the laboratory for about two years. During the mid-1960's to mid-1970's, there was considerable interest in coal-burning MHD and a combustor was developed which would also be applicable to combustion turbines. In the early 19801s, the BCR National Laboratory (BCRNL) became affiliated with the University of Pittsburgh, and a program was begun, supported by the Stare of Pennsylvania, to develop an all-purpose combustor for use with industrial and utility boilers and eventually with combustion turbines. In this paper, we review the work of almost 40 years, indicate our present position, and propose steps to be taken leading to efficient and environmentally acceptable power generation from coal, and specifically to coal-burning locomotives.

Jan 1, 1986

By Frank E. Cash

Although during the past 10 years Alabama has attained an enviable position by its coal-mine accident experience and, like most of the other coal-mining States, has made progress in the safer operation of coal mines, there is still room for improvement, which can be realized only by still greater efforts on the part of employees and employers. From 1993, when accidents were first recorded by the Alabama State Mine Inspection Department, to 1934, inclusive, 3,451 men lost their lives in the production of 569,722,676 tons of coal. The primary purpose of this report is to bring to the attention of the mining industry in Alabama end elsewhere statistics of fatal accidents for 1931-34, with the hope that a study of the causes may lead to reduction of similar accidents in the future.

Jan 1, 1936

By Philip J. Bangerter, Chris Twigge-Molecey

Design for safety is critical to metallurgical plants, due to the inherently dangerous nature of their processes. Two significant areas of concern are: 1. preventing catastrophic process failures that cause damage or injury; and 2. operational safety that directly affects those working in or living near the plant. Process safety involves human behaviour, but the designer can eliminate or control hazards by engineering approaches, and control impacts through the design of the operating procedures. The tools available to guide safe facility design include bowtie analysis, hazard analysis, and hazard and operability studies. Clean plant design principles can guide the design process to address in-plant occupational health and safety issues. Auditing and review is a key part of the overall design process.

Jan 1, 2015

By Finch JA, Uribe-Salas A

The relationship between the process variables and hydrodynamics of a downflow concurrent column (Jameson cell) was investigated in both two and three-phase systems. Gas holdups from 10 to -60 per cent were obtained at gas rates up to 15 cm/s (STP), liquid (slurry) rates up to 25 cm/s, frother concentrations of 5 and 25 ppm, and slurry density (silica) up to 1.23 g/cm3 ina 3.8 cm diameter, 190 cm high column with a 0.5 cm diameter nozzle. Gas holdup decreases with feed rate and increases with gas rate, reaching a maximum (-60 per cent) at a gas rate to feed rate ratio of about one. Gas holdups were higher with slurry compared to water as feed. Stable operation was difficult to maintain at high gas rates especially with low frother dosage; operation was not possible without some frother. Instability was characterised by loss of pool level or formation of slugs. The slugs could move up or down or remain oscillatory. A quantitative relationship between the variables and gas holdup or onset of instability was not identified. Conductivity and pressure-based techniques were successfully tested on-line for estimation of gas holdup and to judge the state of operation (eg formation of slugs).

Jan 1, 1993

Institute of Metals Division Iron and Steel Division Extractive Metallurgy Division Council A W Thornton (ISD), Chairman, R W Shearman, Secretary, C S Barrett (IMD), J C Kinnear, Jr (EMD), John Chipman (ISD), J S Smart, Jr (IMD), A W Schlechten (EMD), M E Volin (MED), D S Eppelsheimer (MIED) Journal of Metals Editorial Advisory Committee J S Smart, Jr, Chairman, W A Dean, J J Golden,T D Jones, Evan Just, J C Kinnear, Jr, M Tenenbaum Pacific Northwest Regional Conference E R Marble, General Chairman, Marshall Huntting, Assistant General Chairman, W C Douglass, Mining Chairman, H C Hughes, Mining Chairman for British Columbia, W C Douglass, Mining Chair¬man for United States, Paul Billingsley, Geology Chairman, W D Nesbeitt, Miner¬als Beneficiation Chairman, H D Kelley, Industrial Minerals Chairman, J G Johnston, Metals Chairman, Lloyd Banning, Iron and Steel Chairman, W G Rouillard, Extractive Metallurgy Chairman, E C Roberts, Physical Metallurgy Chairman, D A Pifer, Mineral Industry Education Chairman, Frederick Brien, General Arrangements Chairman Metals Branch Membership Committee C M Squarcy, Chairman, R C Cole, Harold Mar¬golin, M E Nickel, S K Scovil Bylaws Committee A W Thornton, Chairman, W R Hibbard, Jr, J S Smart, Jr (IMD), John Chipman, T S Washburn (ISD), T D Jones, J D Sullivan (EMD)

Jan 1, 1956

By J Harris, P Kirsch, R LaBouchardiere

æMining + Health in DevelopmentÆ is a project funded by the International Mining for Development Centre (IM4DC, 2012) to develop a centralised database of corporate sustainability initiatives for managing and improving occupational and public health, based on information extracted from social and environmental reports of major mining, oil and gas (MOG) companies. This register of materials has the potential to increase stakeholder awareness of the unique health risks impacting the minerals industry, employees, their families and surrounding communities, as well as to inform stakeholders on global industry approaches to health management.Data and preliminary outcomes from analysis of different MOG corporate sustainability reports on public health and disease management are presented for six African countries (Democratic Republic of Congo, Ghana, Mozambique, Sudan, Tanzania and Zimbabwe) and six Asia-Pacific countries (Indonesia, Mongolia, Pakistan, Papua New Guinea, Philippines and Vietnam).With the minerals industry facing ongoing rapid growth worldwide, including continuous expansion into developing regions, the æMining+Health in DevelopmentÆ project will inform industry, civil society and regulators of current health management practices and programming among the different sectors of the minerals, oil and gas industries and across various regional operations. This baseline information will serve as a resource for minerals industry managers, providing a forum for sharing best practice health management approaches amongst MOG companies.CITATION:LaBouchardiere, R, Harris, J and Kirsch, P, 2012. Mining and health in development - An inventory of global resource industry health initiatives in developing countries, in Proceedings International Mine Management 2012, pp 75-90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By W. L. Hunter

This report describes results of beneficiation and smelting studies conducted by the Federal Bureau of Mines on chromite samples from the Emma Belle and Seiad Creek prospects in the Seiad Creek area, northern California. Samples were chosen from this area because the ore is typical of disseminated types that represent a sizable domestic reserve. The two samples were similar in composition, and both responded in like manner to gravity beneficiation. As the ore was banded, considerable coarse gangue was rejected in laboratory sink-float from a minus-3/4-inch, plus-6-mesh fraction without excessive chromium loss at a medium density of 3.32. An average of 85.6 percent of the chromium was recovered in the sink product, which analyzed 35 percent chromic oxide (Cr203). Tabling yielded concentrates containing 49 percent or more Cr203; however, recoveries, ranged from only 33 to 45 percent. A combination of tabling and electrostatic separation of the table middlings showed that the chromium recovery could be increased to about 73 percent; the composite concentrate averaged 53 percent Cr203.

Jan 1, 1960

By Herty, C. H.

Present-day interest in the question of "dirty steel" has arisen primarily from the increasingly rigid specifications on various grades of steel and from the growing conviction that non-metallic inclusions are the source of many of the difficulties in meeting these specifications. The importance of inclusions has unquestionably been over-emphasized in many cases, but on the other hand many unpublished instances could be recorded where all evidence pointed to inclusions as the primary cause for the failure of steel in rolling or in service. The solution of the problem of dirty steel is not a matter of a few years. There are almost numberless types of inclusions. They segregate in steel ingots in an entirely different manner from other impurities, and, at best, only a start has been made in developing correct analytical methods for their determination. Most of the writers in the field have expressed opinions rather than given facts, and so many variables enter into the manufacture of steel that a study of plant conditions is difficult unless definite facts on certain phases of the inclusion problem are available. This statement is not intended to convey the idea that little work has been done on this problem. On the other hand, the number of investigations has been large, but in most cases too many variables have been present to allow definite conclusions to be drawn. In the body of the text, reference to previous investigations is made at suitable points. Rather than burden the reader with a lengthy review of the literature on the general subject of inclusions, reference to the particular works pertinent to the subject matter of the bulletin has been discussed. Three excellent bibliographies b on the subject have been lately published: one by the Committee on

Jan 1, 1957

By E. P. Bayer

MESABI RANGE ore is mined largely by the open-pit method. This involves having available at all times sufficient working places which in combination will produce ore of guaranteed analysis. Fast- loading power shovels turn out under favorable conditions 1000 tons per hour from each unit. Each unit loads ore differing materially in analysis from that loaded by the others, One may load high grade, another low grade, and another may be in a mixed bank with the lead ore so placed that the product must be mixed at the shovel before it is loaded into cars. In such cases the bank is combed with the bucket, the door being left open to permit the material to fall through.

Jan 1, 1937

By Julio Cezar de Sousa Zorzi

Aços com teor de Mn entre 15% e 30% apresentam ductilidade excepcionalmente alta para sua elevada resistência mecânica, devido à ocorrência de transformação de fases (efeito TRIP) e/ou à formação de maclas de deformação (efeito TWIP) na microestrutura predominantemente austenítica. A adição de Mn ajuda a manter a austenita até a temperatura ambiente, evitando a sua decomposição após o recozimento aplicado depois da laminação a frio. O objetivo desse estudo foi avaliar o efeito da temperatura de recozimento na microestrutura e nos valores de propriedades mecânicas de um aço com 17% de Mn, por meio de simulações piloto das etapas de processamento industrial utilizando dilatômetro e simulador termomecânico do Centro de Pesquisa da Usiminas. Observou-se que o aumento na temperatura de encharque durante o ciclo térmico de recozimento contínuo promoveu a reversão completa da martensita a’ para austenita. Além disso, a alteração desse parâmetro praticamente não afetou o limite de resistência e o alongamento total do aço, embora tenha reduzido significativamente o limite de escoamento.

Jul 30, 2018

By J. J. Fritts, J. L. Patrick, T. L. Wright, C. O. Ensign, W. S. White, J. W. Trammell, J. C. Wright, D. J. Hathaway, R. J. Leone

The copper deposit at White Pine, Michigan, from which a little more than 5 per cent of United States primary copper currently is produced, is a large stratiform orebody, 4 to 25 feet thick and several miles across. The present ore column, containing about 1.2 per cent copper as chalcocite and native copper, is confined to the basal beds of the Nonesuch Shale. This upper Keweenawan (Upper Precambrian) formation is a distinctive gray siltstone unit, about 600 feet thick, overlying and overlain by thick red-bed sequences. All these rocks contain abundant volcanic debris, but the latest known igneous activity within 50 miles antedated the Nonesuch Shale. The rocks are unmetamorphosed and only moderately deformed, mainly by tilting and faults. Pyrite, presumably syngenetic, is the only prominent sulfide throughout most of the Nonesuch Shale. The basal beds of the formation, however, contain disseminated copper minerals instead of pyrite and constitute the cupriferous zone. On a regional scale, the top of the cupriferous zone cuts across bedding, and ranges from an inch or so above the base of the formation in some areas to more than 50 feet in others. However, within the cupriferous zone the distribution of copper shows remarkable stratigraphic control. Certain beds are copper-rich compared to the beds that lie between them and the differences persist throughout the White Pine region. Several darkgray thinly laminated beds in the lower 10 to 25 feet of the Nonesuch Shale are rich enough and sufficiently close enough together to constitute a mineable thickness where they lie within the cupriferous zone. Pyrite is the characteristic sulfide of the Nonesuch Shale as a whole. The principal sulfide mineral of the cupriferous zone at the base of the formation is chalcocite. The succession of minerals outward and upward from the center of the cupriferous zone is native copper-chalcocite-bornite-chalcopyrite- pyrite. The bornite and chalcopyrite are confined to a narrow fringe at the margin of the cupriferous zone. This pattern of mineral zones is believed to represent reaction between syngenetic pyrite and introduced copper. The main copper mineralization is independent of structure and apparently antedates deformation. Details of the geometry of the cupriferous zone indicate the possibility that copper was introduced from the underlying sandstone prior to lithification. The source of the mineralizing solutions and their copper is not known.

Jan 1, 1968

Jan 1, 2004

By John Cory, David Lily, Bill Hissem

The Lafarge granite quarry in Cumming, Georgia is using Principal Component Analysis (PCA) and Biplot charting to identify important variables and control air blast and vibration. Every blasting situation is unique and PCA and Biplot charting help to clarify the major variables determining air blast and vibration.

Jan 1, 2010