Search Documents

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. roof drill. The instructions are based upon two actual installations: one made in a mine on roof drill, model 300, and one in the factory. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other roof drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other roof drills and can determine any necessary modifications if they are not.

Jan 1, 1973

By Godwin J. Igwe

For soil remediation technology to be effective, a thorough understanding of the interactions between a targeted contaminant and the soil matrix is crucial. Proper selection of remediation technology, based on understanding the bonding/binding characteristics of the soil and contaminant, can often result in significant remediation cost savings. Contaminated soil cleanup is complicated by both the physical nature of the soil formation and the behavior of contaminants introduced into the formation. Contaminants can exist in the subsurface in different phase attached to the soil surfaces, dissolved in the ground water, or occupying pore spaces as a separate gaseous or liquid phase. Contaminants properties and how they exist in the subsurface influence their toxicity, mobility and treatability with different remediation technologies A soil characterization study was performed to provide information for remediation technology selection for an inorganic lead contaminated soil. The soil pH, TCLP analysis, thermogravimetric analysis, the soluble anions and cations present, equilibrium leaching tests, analysis by x-ray fluorescence, sequential extractions and speciation analysis using scanning electron microscopy, were all used. Results provided many insights into contaminant behavior in the soil, indicating ultimately whether soil washing or solidification/ stabilization remediation technologies were applicable.

Jan 1, 1994

By N. Kumar Kittusamy

Jan 1, 1974

By Sam McNary

The U.S. Bureau of Mines used the East Fork Pine Creek watershed to conduct a pilot study for an inactive and abandoned mine lands inventory, during which techniques and methodologies would be developed for subsequent inventories. A total of 177 waste dump samples, 191 mill tailings samples, and 36 stream sediment samples were collected. Water samples were collected from 18 sample sites during five sampling events. Waste dump, tailings, and stream sediment samples were analyzed for antimony, arsenic, cadmium, copper, iron, lead, mercury, and zinc. Results indicate a multidisciplinary approach is necessary: disciplines should include geology, geostatistis, geochemistry, geophysics, biology, hydrology, and remote sensing; small prospects do not generally contribute to watershed contamination, major mine and mill sites may contribute metal enriched sediment of metal enriched water; speciation studies and bioavailability studies are important.

Jan 1, 1995

By W. H. Kerns

The Taylor Creek lead-zinc deposit is on Taylor Creek, approximately 1-1/2 miles from tidewater, at the head of Duncan Canal, on the east side of Kupreanof Island, Petersburg district, southeastern Alaska. The property was located in 1903, and a 30-foot discovery cut was put to the west tank of the creek. Very little prospecting end developing has been done since that time. The property was examined by J. C. Roehm, associate mining engineer, Territorial Department of Mines, Juneau, Alaska, in June 1946. From exposure n the creek, a mineralized zone with possible dimensions of 1,700 feet by 1,000 feet was indicated. The general strike was northwest, and the dip was low and variable to the northwest. During September through November 1948, the Bureau of Mines conducted a project on the property. Four diamond-drill holes, totaling 770.5 linear feet, were drilled from the surface and 280 lineal feet of hand trenching done. The mineral deposit was found to occur as patches that appear to be a replacement in dolomitic limestone. The patches of mineralization are small, irregularly shaped, and irregularly distributed. Maps showing the location of the drill holes and trenches, analyses of the cores from the drill holes, and anal lee of the samples from the trenches accompany this report (see, also, appendixes A, B, and C).

Jan 1, 1950

By E. H. Kelton, R. D. Grissinger

In designing structural members of steel and some other materials the design engineer has available recognized values of elastic modulus and safe working stress that may be substituted in well-known engineering formulas to give him desired cross-sectional areas and deflections for a particular part. Zinc, on the other hand, has no generally recognized modulus. It flows under continuously applied loads. Therefore, the designer of structural members must use a range of working stresses depending on the continuous load and the amount of permissible distortion. The only method of obtaining these values is by creep testing. Creep testing of zinc has been carried on for some 20 years by this laboratory, covering a wide range of zinc and zinc alloys. Types of test included tension, compression, and simple and cantilever beams at temperatures ranging from o to I50°C. Specimen conditions ranged from as-cast or as-rolled to accelerated aged in steam or dry air. Effects of plating were investigated also. It is not the intention of this paper to expound all these factors but rather to present the final data on well-known zinc die-casting alloys and to suggest means of applying these data to engineering design. Early Work In the early work on creep testing of zinc, the direct-loading tension method was used. However, direct loading of die castings was unsatisfactory because of the high loads required. For instance, a standard die-cast tension bar having a cross-sectional area of about 0.049 sq. in. would require a direct load of about 1000 lb. for a unit stress of 20,000 lb. per sq. in. Also, tests were made at nominal room temperature, but normal variations caused fluctuations greater than those due to experimental error or other causes, so that control of this variable within ±1/2°C. seemed essential. These two factors led to the development of an apparatus described by J. Ruzicka,' in which the specimens were loaded by means of a lever and were held at constant temperature by means of an oil bath. While Ruzicka's apparatus yielded excellent check results, it seemed desirable to have some setup by which literally hundreds of die-cast specimens could be tested at the same time. This would permit the conducting of a number of low-load tests designed to run 10 years or longer and still leave capacity for current high-load work. Beam testing in a constant-temperature room was the answer. Test Method Preliminary work indicated that die-cast beams of various lengths and cross scctions yielded the same result within reasonable limits regardless of whether they were tested as simple beams, uniformly loaded beams, or cantilevers. Accordingly, the simplest type was adopted. This was a,

Jan 1, 1945

[A Aall, Christian H., M49 B VP, Dir of Smelt & Refin, Am. Metal Climax Inc., 1270 Ave. of the Americas, N.Y. Aaroe, Stanley L., A54 B VP, The W. S. Tyler Co. of Can. Ltd., St. Catharines, Ontario, Canada Abalos, Toodulo Q., J57 A Prod Foreman, Lepanto Cons. Mng. Co., Mt. Province, Philippines Abbass, G., M55 P. O. Box 680, Hong Kong, China Abbitt, James M., A54 770 Sole Blvd., Bartow, Fla. Abbott, Raymond C., J59 3442 Greenwich Ave., Columbus 24, Ohio Abdullah, N. Y., J53 Dept. of Mines, Res. Div., P. O. Box 1016, Tiger Lane, Ipoh Perak, Malaya Abel, John F., Jr., J53- 100 Maple, Littleton, Colo. Abell, Leo M., M31 B Conc Supt, Phelps Dodge Corp., Morenci, Ariz. Abendroth, Harry E., A57 A Geol, Union Carbide India, 183 Brabourne Rd.. Calcutta. India]

Jan 1, 1961

By Satya Harpalani

The four most important parameters controlling the flow of gas in coal are the gas content, permeability, diffusion coefficient and cleat characteristics. Estimates of these and, more importantly, a knowledge about the variation in their values over time are required for simulation of long-term gas production. This paper describes experimental techniques to determine each of these, along with their time dependency, under simulated in situ conditions. It is shown that the permeability, diffusion coefficient and the cleat aperture values are not constant as usually assumed to be. There is a significant variation in their values as a result of changes in the microstructure of coal associated with release and flow of gas.

Jan 1, 1995

By C. Richard Groves

As the level of technology applied in the electrical measurement, control, and display portions of mine hoist systems continues to advance, the issues and concerns associated with the ramifications of the application of microprocessor technology on the safety-related aspects of these systems become paramount. This report, in part tutorial, addresses several aspects of these concerns. Beginning with discussions of microprocessor-based system architectures, the report addresses some existing and anticipated uses of this technology in mine hoist systems and discusses safety related considerations associated with the areas of data derivation; control and display panels; and system reliability issues. The report concludes with electrical maintenance and inspection considerations associated with the safety assurance of microprocessor based mine hoist systems.

Jan 1, 1986

By C. E. Arrington, A. C. Rice

"Part 1. REDUCTION AND USE OF OXIDANTSSUMMARYA study has been made of the volumetric determination of molybdenum by reduction in the Jones reductor, receiving the reduced solution in a mixture of ferric alum and phosphoric acid, and titrating with standard oxidizing agents. In addition to potassium permanganate, which has long been utilized for this titration, potassium dichromate and ceric sulphate have been found to be applicable. The latter oxidants have been found to be especially useful in the form of dilute solutions for the determination of small amounts of molybdenum. The tests revealed that certain internal indicators give excellent results in these titrations.Reason for These ExperimentsThe following study was initiated with the hope of providing the mining and metallurgical industries with an accurate and rapid technical method for the determination of molybdenum in such low-grade materials as ores, rocks, tailings, steels, and alloys containing less than 0.3 percent molybdenum. Although the experimental work was designed with this purpose in mind, many of the results are applicable to material containing a higher percentage of molybdenum.While the Bureau of Mines had an experiment station in Colorado, considerable analytical work was done on what were then (up to about 1923) classed as rare metals. One of these was molybdenum; and in Bulletin 212, Bonardi's (1) 3/ 60-page chapter covered all methods for the analysis of molybdenum."

Apr 1, 1939

"The Society for Mining, Metallurgy, and Exploration (SME) Inc. developed a guide of minimum standards for reporting exploration results, mineral resources, and mineral reserves for the purpose of informing the general public. The SME Guide has been adopted by the Society.History1. In 1988, at the request of members of the Society for Mining, Metallurgy, and Exploration (SME), Inc., the President of SME formed Working Party #79, Ore Reserve Definition, with the mission to develop guidelines for the public reporting of exploration results, resources, and reserves. A Subcommittee was appointed by the Working Party to draft these guidelines and submit recommendations to SME. The Subcommittee's recommendations were published by SME in the April 1991 issue of ""Mining Engineering"", and as a document entitled ""A Guide for Reporting Exploration Information, Resources, and Reserves"" (the SME Guide) in January 1992. Work continued on an ad-hoc basis until 1996, when Working Party #79 was renamed the SME Resources and Reserves Committee and became a standing committee.In 1994, the Council of Mining and Metallurgical Institutions (CMMI) started a concerted international effort to create a set of international definitions for reporting mineral resources and mineral reserves. An ad-hoc International Definitions Group was formed, with representatives from mining and metallurgical institutions from the United States (SME), Australia (AusIMM), Canada (CIM), the United Kingdom (IMM) and South Africa (SAIMM). A major breakthrough came on October 18, 1997 when the CMMI International Definitions Group met in Denver, Colorado and reached a provisional agreement (the Denver Accord) on definitions of mineral resources and mineral reserves. Concurrently, and since 1992, the United Nations Economic Commission for Europe (UN-ECE) was developing an international framework classification for mineral resources and mineral reserves. Starting in October 1998, joint meetings were held in Geneva between the CMMI International Definitions Group and the UN-ECE Task Force, resulting in agreement to incorporate the CMMI definitions into the UN framework classification."

Jan 1, 2003

By C Jincheng, L. Liang, L. Wenjun

"Considering overgrinding in a grinding process, the grinding characteristics of comminuted hematite products using a HPGR and a conventional CC were comparatively studied. The major properties including particle size, grinding kinetics and grinding technical efficiency (Et) were investigated. Individual size distributions (ISDs) of -2.0mm in a HPGR product showed a more significant “double-peak” characteristic than a CC product. As a result, HPGR products were finer and had a wider full-size distribution because of the greater proportion of fines. The parameters m and zi in m-th order grinding kinetics were analyzed by the partial-derivative method and the critical time tc(tc = exp (1/ zi)) was obtained. zi mainly affected the breakage rate when t < tc; otherwise, m mainly affected the breakage rate. In these tests, tc was considerably higher than the grinding times, and HPGR products yielded a higher zi-value than the CC product for the same sieve size. This indicated that HPGR products had a higher breakage rate and needed a shorter grinding time for a certain grinding fineness. Et was calculated by simulating the size distributions of batch grinding products. HPGR products gave a lower Et at a decreasing rate than the CC products for -2.0 mm feed and -0.5mm feed, and then showed a slightly higher Et for -2.0+0.5 mm feed. This indicated that overginding in HPGR full-size products was more serious under the condition of coarse grinding, whereas the efficiency was higher and overgrinding weakened significantly in HPGR coarse products because of screening-out fines. Based on the above research, a new process of “ultra-crushing in HPGR – classified grinding” was advanced, reducing ores tonnage into first stage ball mill significantly, improving grinding efficient and weakening overgrinding in the whole grinding process.INTRODUCTIONIn mineral processing, comminution accounts for a substantial portion (approximately 60~70%) of the energy consumed in plants. As an ultra-fine crushing equipment,the application of the HPGR for industrial comminution has been paid close attention because of its low specific energy, low steel consumption, high capacity and high ratio of reduction, among others (Schonert, 1998; Norgate & Weller, 1994; Fuerstenau & Kapur, 1995). HPGRs comprise two counter-rotating rolls that draw feed material into the roll gap. One roll is fixed to the mainframe, while the other movable roll is mounted on slides and positioned by hydraulic rams. The specific pressing force (SPF) (i.e., total force divided by projected roller area) is typically in the range of 3~9 N/mm2 depending on the application, while pressures of up to 1000 N/mm2 have been measured within the operating gap (Maxton , Morley, & Bearman , 2003)."

Jan 1, 2016

By B. Mishra, W. A. Averill

"The application of various hydrometallurgical, pyrometallurgical and electrochemical processes in the extraction, purification and production of radioactive metals as well as the use of various materials, ego metals and alloys, ceramics, polymers, etc. in the process, construction and handling equipment in the nuclear industry has generated a large stockpile of radioactively contaminated waste material and scrap metal which can not be directly discarded, recycled or considered for long-term storage due to its volume and potential hazards, without the separation of radionuclides. This paper reviews the emerging methods that have been investigated and suggested for dealing with some of these wastes and scrap material.The separation technologies studied for the recovery of radioactive components from the pyrometallurgical and electrochemical processing wastes have been discussed in details with results from some of the recent theoretical and physical modeling work as well as the data obtained from the actual waste treatment. Specific processes shall be described in terms of its advantages and limitations. These emerging separation technologies are being considered by the US Department of Energy as alternatives for dealing with the issues of environmental management [EM] and decontamination and decommissioning [D&D].IntroductionThe high temperature carbothermic or metallothermic smelting reduction methods for metal production are associated with the generation of significant quantity of waste as slags, flue dusts, sludges, residues, effluent salts etc. Certain hydrometallurgical processes also generate lots of aqueous waste due to the inherent nature of the technique. Also, the gas-based reduction processes are not applicable to many stable metal compounds, such as alumina, titania, beryllia, lanthanide and actinide oxides, etc. due to thermodynamic considerations. All these methods cause substantial environmental hazard. There is a need to develop alternative processes which have low waste or ideally a ""zero-waste"" generation.Pyrochemical processes using molten salts provide a unique opportunity for the extraction and refining of many reactive and valuable metals either directly from the beneficiated ore (aluminum, beryllium, neodymium, plutonium, uranium, etc.) or from other process effluent that contain reactive metal compounds. The processes reduce metal compounds electrolytically (A12O 3 and BeCI2) on a carbon anode or by calciothermic reduction (Po, Nd). The by-product, in the latter case, is a calcium oxide saturated halide salt. The waste-treatment to recycle the halide has to be done as a separate step or stored as a contaminated waste. A successful separation technology can provide a new insight to the waste minimization strategy for the nuclear industry."

Jan 1, 1996

By W. R. Ingalls

IF, in this study of the outlook for the copper industry of the United states, I find myself assuming to be prophetic in some respects I shall express myself with hesitation and with the foresight that after the end of the war with Germany the war with Japan may continue; anyway there is sure to be an uneasy period before copper and the other metals begin to flow smoothly through the natural channels of consumption. It is mainly my purpose to survey conditions and suggest some probabilities, or possibilities, rather than to prophesy. In interpreting them it will be necessary to make certain aasurnptions, among which will be (1) expectation of a rise in the general price level,, which so far has been one-sided; (2) continuance of the k. tariff on copper imports; and (3) lock-up of government-owned copper as a military re- serve. Of these assumptions the first is indicated by the lessons from economic history, and by current symptoms. The second and third depend upon political action by Congress.

Jan 1, 1944

By Jalal Vakili

In designing very large excavated slopes which are becoming increasingly common in both mining and civil engineering projects, the most important decision of the engineer is the selection of a slope angle. The purpose of the geotechnical study of the slope is to ensure reasonable stability of the slope in the most economical way. Because the rock mass composing each slope is unique, there are no standard solutions for slope stability analysis. A practical solution is formulated from the basic geologic data, engineering properties of the rock, geometry of the slope, and ground water observations. Stability analysis consists of analyzing the forces causing and resisting slope failure. There are several methods of slope stability analysis. The limit equilibrium method evaluates the overall stability of the sliding mass just on the verge of slip, using some or all of the three equations of static equilibrium of a plane problem. The stress-strain relationships of the rock mass are not considered. Method of analysis include the assumption of the shape of the slip surface. Peterson (10) introduced the Swedish method of analysis in 1916, which is based on cylindrical sliding surfaces. Fellenius (4) in 1926 extended this method and introduced the method of slices. This method was refined by Bishop (I) in 1955 and later used by Morgenstern and Price (8) in 1965. In many cases layers of extremely soft strata or strata weakened by neutral stress cause failure to take place by translation along plane of weakness instead of by rotation on a circular surface. In this paper, a slope with a horizontal layer of weak meterial is selected for analysis. This is a usual case for open pit lignite mines where lignite seam may be non-cohesive and &apos;weaker than the overburden rock or a soft clay layer underlies the seam. It is also a common case of rock fill dams supported on a foundation stratum of clay where the strength of the clay layer is less than that of the rock fill. It is shown that utilizing this method, the location of potential failure surface and the value of the minimum factor of safety can be calculated directly and the trial computations of factors of safety for a number of assumed failure surfaces are not necessary.

Jan 1, 1982

By William H. Snyer

A relatively inexpensive, very fast response photo-optic/fiberoptic system has been conceived, constructed and employed by Denver Research Institute (DRI) to measure charge breakout uniformity on the surface of a very large ANFO detonation. The new equipment and technique was coined OWL (observation without leads). Its unique design provides the ability to monitor or measure detonation velocities and/or detonation breakout characteristics without fiberoptic or any other direct contact with the explosive. This system has proven to be versatile and has been used to measure surface breakout simultaneity on large ANFO detonations, munition case breakout times and velocity of detonation (VOD).

Jan 1, 1990

By André de Albuquerque Vicente

O valor do PREN da liga pode levar a uma previsão equivocada da resistência à corrosão por pite pois, caso haja um desbalanceamento das frações volumétricas da ferrita d e da austenita, as composições químicas das fases poderão ser muito diferentes daquela da liga. Neste caso o PREN de uma das fases pode ficar abaixo do PREN da liga. Caracterizou-se três chapas de aços inoxidáveis duplex laminados com diferentes PRENs: UNS S32304 (Lean Duplex), UNS S31803 (Duplex) e UNS S32750 (Super Duplex). Várias técnicas complementares de análise microestrutural foram utilizadas, tais como de espectrometria de emissão ótica, microscopia óptica e microscopia eletrônica de varredura com EDS acoplado. Realizaram-se análises metalográficas quantitativas para a determinação das frações volumétricas de ferrita d e da austenita e análises químicas semi-quantitativas das fases presentes utilizando-se um MEV com EDS acoplado.

Oct 30, 2017

By R. W. Waytulonis

This paper is an update of the activities of the U.S. Bureau of Mines, other government agencies, and the automotive and truck industry concerning diesel emission control. Enacted and proposed regulations from the U.S. Mine Safety and Health Administration (MSHA) and developments in diesel emission control are presented in terms of their impact on underground coal, metal, and nonmetal mines. Mine air quality regulations proposed by MSHA may require the underground mining industry to comply with new standards. Some mines may be required to take additional actions to meet new diesel particulate and lower nitrogen dioxide exposure standards; however, the mining industry is in a position to benefit from emission controls developed for the on-highway diesel engine market. The U.S. Environmental Protection Agency (EPA) has enacted regulations to reduce emissions from on-highway diesel trucks and buses. Engine manufacturers have responded by developing cleaner burning engines. Fuel producers have responded by providing cleaner burning reformulated diesel fuel, and exhaust aftertreatment devices have been developed to provide additional emissions reductions. Bureau research and development projects seek to determine the advantages of using modern engines and fuels, and to evaluate the efficacy of new exhaust control devices on mining machines. It appears that the diesel engine will continue to be a practical power source for use in confined environments because no other available power source is as mobile and efficient.

Jan 1, 1993

By Richard Quirk

This report describes methods and techniques employed by The Glidden Co. of Cleveland, Ohio, in explorating an ilmenite-bearing sand deposit in Ocean County, New Jersey, during 1960 to determine ore reserve potential and the feasibility of mining and establishing a milling plant on the property for the production of ilmenite concentrate. The property covered approximately 1,250 acres. Comprehensive sampling by water-jet drilling indicated the deposit averaged 20 feet in thickness and contained 4.5 percent heavy minerals, of which 80 to 85 percent was ilmenite and leucoxene. Average depth of the water table as determined by auger boring was 16.8 feet. Pilot plant tests indicated that circular concentrators in combination with spiral concentrators would recover at least 80 percent of the heavy mineral content of the sands. It was estimated that sufficient ore reserve tonnage had been developed to supply the company&apos;s Baltimore chemicals division, pigments department, with a suitable grade ilmenite concentrate for a period of 20 years at the present rate of pigments production. The property was designated as Lakehurst mine and plans are in progress for mining development and plant construction.

Jan 1, 1963