Search Documents

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. In this volume and in a series of Reports of Investigations immediately following the factual data obtained during the project are reported. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location und name are shown on the appropriate half-township map.-The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this eeri88 of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1 (R. I. 4251). The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table tor each half township is given with the discussion covering that area.

Jan 1, 1948

By John J. Baz-Dresch

Catalyzed diesel particulate filters (CDPF's) reduce the concentration of diesel particulate matter (DPM) and may reduce the emissions of carbon monoxide (CO) and hydrocarbons (HC) in diesel exhaust. Asamera Minerals' Cannon Mine first installed CDPF's in 1987, and currently has 12 diesel-powered vehicles equipped with CDPF's. The Cannon Mine and the U.S. Bureau of Mines collaborated to evaluate the durability and performance of a CDPF. One of the CDPF's used at the mine was periodically evaluated in the USBM's diesel emissions laboratory after 839, 1,584, and 2,881 h of in-mine service. The objectives of this report are to present results from the USBM's evaluation of this CDPF, to describe the Cannon Mine's experience and cost analysis of using CDPF's, and to make recommendations for the future use of CDPF's. CDPF's improve air quality at the Cannon Mine, but they frequently become plugged and are subject to excessive mechanical shocks and stress, shortening their useful life. Mine records indicate that CDPF's account for 0.8 to 4.9 pct of the vehicles' operating cost at the lVine. CDPF life to date has ranged from 1,671 h to more than 5,992 h. Laboratory tests of the CDPF determined that DPM removal efficiency decreased and regeneration temperature increased over time.

Jan 1, 2010

By R. B. Woodworth

In the sinking of bore holes, there are but two fundamental operations —drilling and hoisting—which determine in the main the character of drilling mechanism and structures. There are endless ramifications, however, in the execution of these fundamental operations, according to the purposes for which the bore holes are drilled, their maintenance after completion, the protection and convenience of workmen, etc. The three main lines of use for bore holes are in mineral exploration, the sinking of water and salt wells, and the exploitation of pqtroleum and natural gas. This paper has to do more especially with the last. Here again there are many divergences. Wells may be drilled by either the percussive, the hydraulic, or the abrasive method. Finally, each of these methods, as applied by drillers of diverse nationalities, has followed somewhat different lines of development. The American system of cable-tool drilling has perhaps had the widest application; the hydraulic rotary is also in extensive use; but the Canadian system, the Galician system, and the Russian free-fall system all have their points of recognized merit and are preferred by operators accustomed to their use. These differences in drilling procedure, which rest ultimately on essential variations in geological conditions, are reflected in the drilling structures as well as in the drilling mechanism. The purpose of the present paper is to record those stages in the development of the application of steel to the construction of drilling mechanism and structures with which the writer has been intimately associated, and to contribute to the history of the art of drilling other data acquired in the course of his personal investigations. It is necessarily limited by reason of space to American practice, with especial reference, therefore, to the cable-tool system and the hydraulic rotary method of drilling wells for oil and gas.

Jan 1, 1916

By J. P. Gliddon

Since 1980 a number of significant changes have been introduced at Palabora in an effort to off-set the effects of reduced product price and increased unit cost of inputs. These changes and improvements include major equipment rationalization programs, the introduction of trolley assisted truck haulage, adoption of a sophisticated computerized truck control system, pit design enhancements, improved drilling practices, use of emulsion explosives and the installation of an in-pit crushing and conveying system. The various changes, their effect on the operation and their contribution to cost reduction and improved productivity at Palabora are considered.

Jan 1, 1987

By Richard P. Cislo

The evaluation of the effectiveness of the time domain Coal Interface Detector developed by the General Electric Company under contract H0155120 is the subject of this report. The sensor utilizes differences in the time characteristics of shearer vibrations as sensed by an accelerometer mounted on the ranging arm to discriminate the cutting of coal and rock. Pour identical time domain sensors were supplied by the Bureau for field evaluation. The performance of the time domain sensor was evaluated by an extensive field test and data collection program that included four longwall mines and a total of nine mine visits. The intent was to determine the sensor's applicability to a wide range of mining conditions and to document its limitations. Results of the extensive field tests indicate that shearer vibration data processed by GE's time domain signal processing algorithm cannot be used to reliably detect when the cutting drum crossed the coal/rock interface.

Jan 1, 1987

By Madan M. Singh

This section is unique to the Handbook in that it is the only section that deals with underground excavations for nonmining purposes. The editors were of the opinion that the section should be incorporated because the subject matter covered by the chapters is closely related to mining, and many mining engineers are currently involved in these activities. As we enter the decade of the 1990s activities in this category will increase, enhancing the relevance and utility of the material discussed. As the population increases, especially in metropolitan areas, the necessity to go underground will be greater. At the present time, not only are subsurface shopping malls and pedways connecting buildings becoming commonplace, but structures as diverse as the Civil and Mining Engineering Building on the University of Minnesota campus, a road-and-fleet maintenance facility in Multnomah County, OR, and even an ice cream parlor (Dairy Queen) in northern Wisconsin have been constructed underground. Placing utilities below the surface has numerous advantages and is now customary. Rapid transit and highways through tunnels in urban areas have been the norm for many years, but subterranean stormwater reservoirs, power plants, industrial warehouses, and food storage silos are relatively new innovations. The philosophy of underground defense installations is ancient, but their requirements and designs have trans-formed radically as technology advances. The use of under-ground space for disposition of wastes is modern, since it is recently that environmental concerns and waste disposal costs have assumed increased significance.

Jan 1, 2008

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

By J. M. Sands

Production of oil in Oklahoma during 1927 amounted to 273,256,900 bbl. (Table l), an increase of nearly 100,000,000 bbl. over the previous year. All of the major fields declined with the exception of those of the Seminole district which produced 136,105,000 bbl., almost one-half of the total production of the state. Because of this large new production, most of the development in the state during the year took place in that district. The Seminole City pool located in T.-9-N., R.-6-E., was the first of these pools to be developed. The Indian Territory Illuminating Oil Co. brought in the first well in this field in March, 1926, for 1100 bbl. This well is located in Sec. 24-T.-9-N., R-6-E., and produced from the Hunton lime reached at depth of 3900 ft. The first Wilcox production was developed by the Independent Oil & Gas Co. and R. S. Garland in Sec. 26, T.-9-N, R-6-E. This well was being drilled for production in the Hunton lime but was dry in this horizon and was deepened to the Wilcox sand in July, 1926, and at the total depth of 4069 ft. developed a maximum production of 8000 bbl. daily. It held up in wonderful manner and was the cause of not only the development of this pool but the prospecting of the whole district for the Wilcox sand. This led to the discovery of the other major pools in that district. Seminole City pool reached a peak production of 264,500 bbl. on February 22, 1927, and slowly declined so that by December it had a daily average of 56,200 bbl. from 321 wells. The second pool in this district to be discovered was the Searight pool which was discovered by F. J. Searight et al. in Sec. 33, T-10, R-6, in April, 1926. The first well was drilled to the Hunton lime encountered at 4115 ft., and came in for 1300 bbl. daily. During August, 1926, the second well was drilled on the same farm through the Hunton lime to the Wilcox sand which was encountered at 4360 ft. It came in for an initial production of 4000 bbl. daily. This started active drilling in this field for the Wilcox sand. The field had a peak production of 40,621 bbl. on June 15, 1927, and declined to a daily average of 22,300 bbl. from 73 wells during December.

Jan 1, 1928

By I. R. Kramer

I. R. Kramer (Martin Co.)—In a recent paper Nakada and Chalmers24 reported some observations of effects of surface conditions on the stress-strain curves of aluminum and gold single crystals. It is of interest to compare these observations with the results published previously in this journal and to comment on their general conclusions. In brief, Nakada and Chalmers concluded that the removal of the surface layer of a prestrained specimen lowered the stress-strain curve for aluminum but not that for gold. Further, they concluded that the surface work hardening of aluminum is confined to a depth not more than l0-3 cm. In our results25 published previously, it was pointed out that when prestrained specimens of aluminum and gold were polished to reduce the thickness upon reloading the initial flow stress decreased markedly. Further if a sufficient amount of metal was removed, the yield point failed to appear. With continued application of the load the stress-strain curve became coincident with that of the virgin crystal. We have found this behavior in some 100 determinations to hold consistently for gold, aluminum, and copper in both single and poly-crystalline specimens. The amount of strain required before the curves coincided depends upon the amount of metal removed but it is usually less than 0.01. This type of behavior is the same as that reported for metarecovery by other investigators.29 For aluminum specimens which have been prestrained and then heated to temperatures above 50°C we have consistently found that the stress-strain curve was typical of the orthorecovery28 type. In this case the stress-strain curve always lies below that of the virgin specimen. With respect to Ref. 24 the curves for aluminum are always below that of the virgin curves, while those for gold become coincident. This observation indicates at least for aluminum that the specimens must have been heated to a temperature high enough to cause recovery by an alteration of the internal dislocations. In addition, a recovery would be expected because of the removal of the surface work-hardened layer. Nakada27 had reported that, with his particular apparatus in which a perchloric acid polishing solution was used, the temperature of the specimen increased 65°C. The curves presented in Ref. 24 for gold do not permit one to detect the initial flow stress upon reloading after the surface-removal treatment. In fact, contrary to the method used by Nakada and Chalmers, the change in the stress-strain curve produced by a surface-removal treatment cannot be described in terms of a decrease in stress at strains much higher than that at the initial flow stress because of the coincidence of the curves at the higher strain values. With regard to the depth of the work-hardened surface layer, our data show for aluminum single crystals (7.5 by 0.3 by 0.3 cm) that the initial flow stress remained constant after 12 x 10-3 cm had been removed from the thickness. This depth was independent of the prior strain. For gold crystals this depth is somewhere between 10 x 10-3 and 20 x 10-3 cm. Y. Nakada (author's reply)— Kramer states,28 "for aluminum specimens which have been prestrained and then heated to temperatures above 50°C, we have consistently found that the stress-strain curve was typical of the orthorecovery28 type. In this case the stress-strain curve always lies below that of the virgin specimen." However, Cherian et a1.26 discovered that aluminum polycrystals annealed at 32" and 100°C showed the metarecovery behavior. They showed that the orthorecovery behavior did not appear until the crystals were annealed at 150°C. Kramer suggests28 that the drop in the flow stress of aluminum crystals after the surface removal by electropolishing24 may be due to the recovery caused by the temperature rise which may occur during the electropolishing.27 However, as indirectly stated in Ref. 24, the current density used in these electro -polishing experiments was 0.15 amp per sq cm. According to ref. 27, this current density should cause a temperature rise of only 40°C. This may cause the metarecovery but not the orthorecovery. Furthermore, as stated explicitly in Ref. 24, the surface removal was accomplished by chemical etching as well as by electropolishing. The results were the same for both electropolishing and etching. During the etching, the specimen temperature did not rise above 35°C. Some aluminum crystals were placed in water at 35° C for 30 min. These crystals did not show the decrease in flow stress. Therefore, it is quite clear that the flow-stress drop after the surface removal is not caused by a high-temperature recovery. However, as Kramer points out,28 it is quite possible that the internal dislocation structure may have been altered because of the removal of the highly work-hardened surface layer. However, how much this rearrangement contributes toward the flow-stress decrease is not known at present.

Jan 1, 1965

By Steve Kral

About 500 mineral-processing professionals from around the world gathered in San Francisco, CA in Oct. 22-27, 1995 for the XIX International Mineral Processing Congress (IMPC). Following the theme “Leading Mineral Processing into the 21st Century Through Advanced Technology,”186 speakers from 28 countries covered research and development activities and innovative processes. Subjects included comminution and simulation control, physical and chemical processing, flotation practices and fundamentals, precious metals processing and mineral waste and the environment.

Jan 1, 1996

By Masami Nakamoto

Controlled thermolysis of gold(I) thiolate complex, [C14H29(CH3)3N][Au(SC12H25)2], at 180 °C for 5 h under an N2 atmosphere produces novel gold nanoparticles passivated by alkyl groups derived from the precursor complex, the TEM photograph of which shows spherical particles with average diameter 26 nm. Since Brust et al. reported the two-phase reduction of AuCl4 - by NaBH4 to afford monodispersed gold nanoparticles passivated by alkanethiolate ligands (1), plenty of preparative investigations on gold nanoparticles (2,3) and its surface modification (3,4) have appeared, because of their potential applications in microelectronics (5). However, those preparative methods generally involve the reduction of AuCl4 - by reducing agent NaBH4 in the presence of suitable organic stabilizers such as alkanethiol (1-4), phosphane (5), quarternary ammonium salts (6), surfactants (7) or polymers (8). On the other hand, O?Brien et al. recently reported the preparation of organically capped gold nanoparticles at 190 °C, where tri-n-octylphosphine oxide and/or n-octadecylamine are used both as a reaction medium and as a passivating ligand (6), but this procedure also needs NaBH4 as reducing agent. Our strategy of novel preparative method of gold nanoparticles is the combination of reductive elimination of thiolate ligands and simultaneous attachment of organic moiety on the growing nuclei. Gold(I) thiolate complexes with ammonium cations were useful for our preparative method. We now report the controlled thermolysis of gold(I) thiolate complexes, [R(CH3)3N][Au(SC12H25)2] and [R(CH3)3N][Au(SC6H4-p-R?)2] (R= C14H29, C12H25; R?= C8H17, CH3), under an N2 atmosphere, where the powder of gold(I) thiolate complexes completely melts to afford the precursor liquid and then the liquid gradually decomposes. In spite of no use of reducing agent and solvent, reduction reaction is thermochemically induced to afford novel gold nanoparticles passivated by alkyl groups rather than by alkanethiolate ligands. Figure 1a shows a typical transmission electron microscopy (TEM) image of gold nanoparticles prepared by thermolysis of [C14H29(CH3)3N][Au(SC12H25)2] at 180 °C for 5 h, indicating a controlled growth of spherical gold nanoparticles. As shown in Fig. 1b, these spherical gold nanoparticles display the size distribution ranging from 5 to 50 nm. Although the particle size is larger than that of thiol-derivatized gold nanoparticles (less than 5 nm) prepared by NaBH4 reduction (1-3), the aggregation of gold nuclei is smoothly regulated and the growth of core gold is limited to be 26 nm in average diameter in spite of thermal procedure.

Oct 1, 2003

By Earl T. Hayes, W. M. Sternberg, F. P. Williams

"INTRODUCTION The limited domestic demands for lithium salts and metal before the war were met readily by the use of minerals particularly lepidolite (lithium mica) and amblygonite (a lithium phosphate), from which lithium can be recovered relatively easily. New wartime uses, however, created such a demand that it became necessary to turn to spodumene (a lithium feldspar) as the principal source of supply. Although very large deposits of spodumene occur in South Dakota and in North Carolina, it much more difficult to extract lithium from spodumene than from lepidolite or amblygonite.During the spring and summer of 1942 a study was made in Salt Lake City laboratory of the Bureau of Mines on the recovery of lithium from spodumede. Preliminary tests were made on two processes - roasting with potassium sulfate 4/ 5/ and roasting with calcium chloride and calcium carbonate 6/ -,which appeared to be the most promising of the various processes that had been proposed. By roasting spodumene with approximately its own weight of potassium sulfate at 1,050º C. and leaching the product with water, about 70 percent of the lithium could be extracted. Consumption of the relatively expensive potassium sulfate, however, was high; much of the potassium was found in the insoluble leach residue, end large amounts were lost by volatilization and dusting. By roasting the spodumene with calcium chloride and calcium carbonate, nearly 90 percent of the lithium was chloridized temperatures of 850° to 1,050° C. Much of the lithium could be extracted from the calcine by leaching with water after roasting at the lower temperatures, but volatilization of lithium chloride was appreciable, amounting to 20 to 25 percent in a direct gas-fired furnace at temperatures of 800° to 850° C. At 1,000° to 1,050° C., volatilization was far from complete. Thus, it would be necessary to use both fume collection and leaching of the calcine, unless the roasting temperatures were sufficiently high to volatilize all the lithium chloride. Because of the well-known difficulties of collecting chloride fumes, it was decided to search for a better process."

Mar 1, 1946

By Effie T. Kurt, Jack Wright, J. W. Watkins, Cynthia Pearson

"The analysis of water produced with crude petroleum has interested oil producers since inception of the industry. Records of the first analysis of mineralized water produced from an oil-productive formation are obscure, and references to the first use of brine analyses to assist in solving problems of petroleum production are not available in the technical literature. However, many early reports of the Federal Bureau of Mines 5-8/ and. Federal Geological Survey, 9-11/ as well as articles in engineering and geological placed special emphasis on journals ,12-l4/ the importance, interpretation, and application of water analyses.One of the earliest applications of water analyses, and still a major one today, is for identification of intrusive waters in oil wells. This may be done by comparing the chemical constituents of a sample of water indigenous to the oil-productive formation with those of samples from upper, water-bearing formations within the same general area. Some earlier investigators recognized the need for analyzing samples of all waters encountered in drilling operations. Ambrose15/ stated, in part, ""In wells being drilled, the engineer should grasp every opportunity to get a true sample of water from each sand. . .,"" and, ""The waters of each oil field are chemically different from those of another field."" The validity of the latter observation and the importance of the former one have been borne out by comparing the results of analyses of many samples and noting the differences in relative concentrations of like constituents of waters from the same geological formation in different localities or oil pools."

Apr 1, 1957

Meeting called to order by President Herres, eleven o'clock A. M., Monday, August 27, 1928. Address of Welcome by Mr. T. S. Taliaferro, Jr. Address by Mr. William Redshaw, Chairman of the Rock Springs Chapter of the Institute. Paper, "The Effect of Mechanical Coal Mining on Mine Safety," by Lyman Fearn, State Mine Inspector, Wyoming. Paper, "Safety," F. C. Miller, Chief Chemist, Colorado Fuel & Iron Com¬pany, Trinidad, Colorado. Afternoon session, meeting called to order two P. M. On suggestion of Mr. William Littlejohn, the President appointed a special resolutions committee, consisting of Messrs. P. J. Quealy, R. L. Hair and William Littlejohn, to draft resolutions protesting against the granting of a franchise for piping natural gas into Salt Lake City, to be sent to the City Commissioners of Salt Lake City, with carbon copy to the Utilities Commission of Utah. The Committee submitted resolutions which, upon motion of Mr. Littlejohn, and seconded by Mr. Butler, were adopted and sent by telegraph to the Utilities Commission and the City Commissioners.

Jan 1, 1928

By J. G. Trowell, D. T. Magee

"IntroductionMANITOBA'S first recoverable oil was from the California Standard Daly 15-18 well in Lsd. 15, Sec. 18, Twp. 10, Range 27, W.P.M., completed early in 1951. This well also gave the first indications of commercial production in the Williston basin, which is centred in North Dakota and extends into southeastern Saskatchewan and southwestern Manitoba. Subsequent drilling in the Manitoba portion of the basin has revealed the presence of oil in more or less commercial quantities at various points in an area approximately four townships in width and eleven townships in length.Although completions are becoming fairlly widespread in the area,, the greatest activity is in the Virden district, with the focal point in the Daly field, approximately eight miles west •of Virden. This paper will deal with the various techniques used in the Daly field, where •completion problems have •been unusually troublesome. Techniques evolved there have already been used with success at other points in southwestern Manitoba.Daly FieldGeneralTo date, all production has been from the Mississippian limestone, which is encountered •at depths ranging from 2,300 to 2,500 feet. Pay thickness is •of the order of 100 feet. Core analyses indicate average porosity .of about 9 per cent but permeabilities, for the most part, are extremely low."

Jan 1, 1953

By M. J. Nicol, T. Moyo

Ammoniacal solutions are an effective lixiviant for the oxidative dissolution of some mineral sulphides. A detailed study of the anodic dissolution of chalcopyrite in ammonium sulphate-ammonium hydroxide solutions has been carried out using cyclic voltammetry, chrono-amperometry and rest potential measurements. The role of the copper(II)/copper(I) redox couple in the oxidation process has been evaluated. Rest potentials have been found not to be affected by oxygen but to increase with an increase in initial copper(II) concentration. Pseudo-steady-state anodic current densities measured in the absence of copper(II) ions at the rest potentials obtained in the presence of copper(II) ions increase with increasing concentration of copper(II) ions, confirming the positive effect of copper(II) ions on the rate of dissolution of the mineral. Cyclic voltametric and chrono-amperometric data show that in the absence of initial copper(II) ions, the rate of dissolution in the presence of dissolved oxygen is significantly lower. These results confirm that the effective oxidant for the mineral under the conditions of the study is copper(II) and not dissolved oxygen. Coulometric measurements have been used to establish the stoichiometry of the anodic reaction at different potentials.

Jan 1, 2014

By B. Yarar

Samples of coal from an adit in the Fording River District of British Columbia showed hydrophilic properties between depths of 0-24.5 meters and was naturally hydrphobic at higher depths. Laboratory experiments indicated that weathered samples (i.e., those mined at 0-24.5m) could be upgraded by froth flotation at pH<2 following slimes removal. The i.e.p. of samples varied regularly between pH=1.6-4.1, the weathered fractions being at the lower end of the pH scale. These values followed a pattern comparable with the flotation behavior of samples. A patchwise structure for coal surfaces determining the resultant disjoining pressure, which in turn determines flotation-non flotation relationships is postulated.

Jan 1, 1982

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

By Carl Belser

This report is the first of a series dealing with the oil-shale reserves of the Green River formation in the Rocky Mountain Region. The known oil-shale reserves of northwestern Colorado at present considered to have economic value apparently are confined to the Piceanco Creek basin between the Colorado and White Rivers. The number of sampled sections is small, but there can be little doubt that the Piceance Creek basin is a potential source of enormous quantities of liquid fuels and the related byproducts obtained from oil-shale processing. The partly blocked and inferred oil-shale reserves of 25-gallon-a-ton shale are estimated to have an oil yield of 125 billion barrels and the reserves of 15-gallon-a-ton shale are estimated to have an oil yield of 494 billion barrels. The number of available sampled sections is inadequate for making firm estimates.

Jan 1, 1951