Search Documents

Ground falls (roof and rib) have historically been responsible for about 50% of all fatalities in bituminous underground coal mines. In some recent years, the number of ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, last year?s Crandall Canyon twin mine disasters, in which 9 miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990?s these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents in the past 5 years. Progress has also been made in pillar recovery. Safer mining technologies have reduced the number of fatal incidents, but some recent failures have underlined the need for careful management of the retreat mining process. On the other hand, more than 400 miners continue to be injured each year by rock falling from between supports, and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities. Available technologies such as roof screen, rib bolting, and inside control roof bolters could dramatically reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Ronald R. Rose

Currently six economic heavy mineral deposits are known on the Penholoway Terrace. These are (from south to north) the Green Cove Springs Mine (GCS), Boulogne Mine, Folkston Mine, Mission, Lulaton, and Ludowici. The GCS deposit is located to the west of Highway 17 between the towns of Green Cove Springs and Palatka in the state of Florida and has been mined since 1972. To the north, the erosion created by Black Creek restricts the northern extension of the orebodies and to the south a karst depression and erosion by the St. Johns River restrict southern extensions. The deposit is 20 miles long and up to 4.5 miles wide. Deposit thickness is from 5 feet up to 45 feet. The deposit is a series of regressive barrier island sequences deposited during the Pleistocene along the ancient Penholoway and Wicomico shorelines. The initial transgression of the ocean up to the location of the western Henry orebody was an extensive sea-level still stand as evidenced by the unit thickness and stacked transgressive regressive sequences. This period was followed by sporadic regressing seas and still stands, progressing eastward and stranding the sand bodies which make up the East Extended, TE, and East TE Ridge orebodies. The orebodies are underlain by predominantly non-mineralized fluvial sands and occasional back barrier lagoonal deposited clays. There is a predominance of wetlands on the southern extents of the zone as the surface elevations decrease due to a large karst depression.

Jan 1, 2005

By M C. Goode

The use of electrical or electronic safety systems to protect personnel, and the engineering tasks associated with the design, manufacture and maintenance of these systems are referred to using the term ‘functional safety’. In the past ten years, the use of such systems has transitioned from its traditional base, in oil and gas major hazard facilities, to being a part of most large mining and materials handling projects. In particular, functional safety is rapidly becoming a significant component of Australian iron ore projects, typically in the form of emergency stops, remote isolation, drive through interlock, robot cell entry or mobile machine anti-collision systems. While these types of systems have been in use in iron ore for a long time, functional safety standards (eg AS61508, AS62061, AS4024.1503) require more rigourous demonstration of the level of risk reduction provided by the systems.The early engineering project development phases require a number of key decisions to be made around functional safety implementation. The decisions made at this point in a project will go on to dictate the required types of risk assessment and analysis, equipment selection, sizing of substations, and training and maintenance requirements for owners. For project teams that are unfamiliar with functional safety, or inexperienced in its application, an incorrect decision or failure to understand the requirements of the chosen standard can lead to a failure to meet contract requirements, as well as major cost and schedule overruns.This paper examines the implications of functional safety on early engineering studies, focusing on the following questions: How does a designer or company determine what standard is best suited to their project? What key aspects of functional safety design need to be considered during project development? And finally, how can the impact of functional safety to the project be minimised?CITATION:Goode, M C, 2017. Functional safety impacts on study stages of major projects, in Proceedings Iron Ore 2017, pp 347–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Coal mining in Indiana is limited to the south-western portion of the state, with coal currently being recovered in 19 counties. The coal-producing area of the state covers approximately 6,500 square miles. Although most of the coal in Indiana is recovered by surface mining methods, a small percentage is recovered through underground mining. To date, 40 percent of the known coal reserves have been removed. Indiana has about 33 billion tons of identified coal reserves, of which approximately 17 billion tons are recoverable using current technology. Of this recoverable coal, about 15 billion tons are recoverable by underground mining and 2 billion tons are recoverable by surface mining methods. The State of Indiana has regulated the environmental impacts of coal mining since 1941. Indiana was the second state in the nation to pass legislation requiring mined land reclamation. Its SMCRA regulatory program was approved July 29,1982, and its Abandoned Mine Land Program was approved July 29, 1982.

Jan 1, 1992

By A. M. Dale, J. Standeven, B. Evanoff

We encountered several areas of methodologic uncertainty during development of a data collection method for use with vibrating hand tools in metal assembly. A local manufacturer sought our assistance designing a data collection method for evaluating and predicting risks of upper extremity disorders associated with use of vibrating hand tools. Current methods of vibration measurement are described in ISO 5349 [2]. However, the complexity of measuring vibration along with other exposures such as force and posture has limited the number of workplace-based studies of upper extremity disorders that have included direct measurements of vibration. Data from this preliminary study was used to look at two issues: a comparison of vibration values between production and non-production workers when performing the same task, and a comparison of worker ratings of vibration comfort to direct measurement of tool vibration. Methods Eight experienced production workers used each of six metal fastening tools to install fasteners. Vibration was collected by 3 tri-axial accelerometers, one attached to the tool handle following ISO 5349 recommended locations, one attached to the hand dorsum on the 3rd knuckle and one to the thumb side of the wrist. Data sampling rate was 10,000 samples/second. Hand grip and feed forces were obtained using a Novel pressure sensing mat on the palm. Each trial consisted of installing 10 fasteners per tool for each of the 6 tools. The test set-up placed the wrist in the position typically used by the operator during production. Each worker documented subjective comfort and effort ratings on a seven point scale following each series of fastener installations. One series of testing was completed by three non-production workers inexperienced in fastener installation to simulate use of alternative employees for data gathering. Vibration data for each trial were acquired, digitized, and stored using Lab View. The X, Y, & Z axes were used to calculate the vector sum response for each tri-axial accelerometer. The tool data were digitally filtered following ISO recommendations. Calculated data consisted of the mean RMS over the tool’s on- time, the starting and breaking peak impulses, and the peak of the frequency response. Results Production workers (n=8) were right hand dominant males with a mean age of 55 years and normal hand strength (mean right grip = 106 lbs). Non-production workers (n=3) had similar characteristics. We found large and statistically meaningful differences in hand force during tool use between production and non-production workers (mean production workers = 9.77 lbs, mean non-production workers = 43.30 lbs, p = 0.0001). Vibration values obtained from the hand also showed a statistically meaningful difference (mean in production workers = 0.67 Gs, mean in non-production workers = 1.48Gs, p = 0.0014, figure 1). Experienced worker ratings of comfort during tool use demonstrated a moderate correlation with measured vibration (r=0.63). Worker ratings trended with direct recordings from the tool handle as shown in figure 2.

Jan 6, 2006

By Reginald Dias

Mining operations take a tremendous toll on equipment, operating in difficult conditions day after day. Owners and operators cannot make the job any easier, but they can give their equipment an advantage. Equipment life may be extended through preventive maintenance and the proper application of quality lubricants. This means lubricants that are made to last longer and stand up better to the punishment mining equipment must endure. There are several practices to consider as part of a successful preventive maintenance program. A good place to start is to review original equipment manufacturer recommendations about servicing and maintenance intervals for each part of the equipment, especially the engine. If these recommendations have not been followed, owners and operators must begin periodic service work on equipment to help minimize equipment down-time and extend engine life.

Jan 1, 2003

Smart defense: that?s what the industry needs to play for the next four years, according to panelists at the 118th Annual Meeting of the Northwest Mining Association (NWMA), which met December 2-7 in Spokane, WA. The conference was well attended, with approximately 2,200 attendees, 244 booths in the two packed exhibition halls, and a rich offering of short courses, field trips, social events and technical sessions. Speakers at the packed legislative session articulated many of the frustrations felt by members of the mining community after the U.S. elections in November, and offered words of advice. Matthew Ellsworth, the new Government Affairs hire at NWMA, stated it best: ?Elections are like Christmas: you find out who?s naughty and nice ? and it?s always going to come again.?

Jan 1, 2013

By Susanna G. de Jager, Francis W. Petersen

"To enable the prediction of reagents suitable for fine coal flotation, it is necessary to develop a methodology applicable to different South African coal types. Statistical confirmation of the applicability of this methodology is important to avoid recommendation of reagents on a trial and error basis.The study included 5 coal samples from different collieries and included Highveld seam 3 and 4 coal (as one sample), Waterberg coal (zone 10 -11), Highveld seam 5 upper coal and Witbank seam 2 and seam 4 coal. Seam 3 and 4 (mixture) coal, Waterberg and the seam 5 upper coal were all found to be vitrinite rich coals. The coal characterisation study included petrographic analysis, proximate analysis, float-sink analysis, oxygen-containing functional groups, surface extraction, flotation release analysis and contact angle measurements. Flotation tests were used to validate expectations from the characterisation of the coal samples.RESULTSThe flotation data indicated that all of the coal samples were amendable to froth flotation. The best results were obtained with the Witbank seam 2 coal and the poorest flotation with Syferfontein seam 5 coal. The flotation tests showed that the best reagents to float all of the coal samples studied were iso-decanol and dodecene. These reagents produced flotation products that were near to the release curve, which are the optimum flotation results (obtained when using iso-paraffin as collector). Dodecene resulted in low ash products and iso-decanol in high yield products."

Jan 1, 2003

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1982 was $299.4 million, a decrease of $14.4 million from that of 1981; the decrease continued a downward trend that started in 1980. Output of most nonfuel minerals declined; cement, crushed stone, lime, sand and gravel, and clays were the major commodities produced in the State. Despite the decrease in mineral output, Alabama led the Nation in the production of crushed marble; was second in bauxite; third in ferroalloys and oyster shell; fourth in bentonite and dimension marble; fifth in common clay. fire clay, and kaolin; and sixth in masonry cement and lime.

Jan 1, 1984

By Steven G. Vick

Effects of the August 1995 failure of the Omai tailings dam in Guyana continue to be felt throughout the mining industry. This article is taken from the final report of the independent body of experts commissioned by the government of Guyana to establish the cause of the failure. It explains what happened, why and how to avoid it in the future. Despite environmental, health and safety effects that were negligible by any objective measure, the failure has received wide international attention. Coming on the heels of the shift in exploration targets and development opportunities to developing countries, it has intensified interest in tailings dam safety and environmental management issues. An informed understanding of the nature of the failure and its effects is key to responding to these concerns.

Jan 1, 1996

By J. B. Gayle

PRESENT flotation processes depend almost entirely on the buoyant properties of air bubbles to effect separations of mineral and gangue, but there is no convenient method for measuring aeration in flotation cells. Consequently the relation between aeration and cell performance has not been definitely established. In connection with a comparative study of kerosene and froth flotation processes, a modification of the displacement method' was developed in which air escaping from the cell surface is measured with a wet-test meter. The arrangement shown in Fig. 1 is satisfactory for use with a number of cells and is not critical, except that care must be taken to use connections and tubing large enough to avoid excessive back pressures. Attempts to use smaller tubing resulted in back pressures that caused displacement of the liquid level in the receiver, so that some air was lost around the sides, an occurrence readily visible when measurements were taken with only water passing through the cell. With the arrangement shown, the manometer indicated an average reading of about 1/2-in. water pressure. No loss of air was evident. Fig. 2 presents typical data for a standard Denver sub-A 24x24-in. unit cell operated at impeller speeds from 0 to 710 rpm. Each plotted point represents the average for five readings distributed over the entire cell surface. Readings were taken with only water passing through the cell. Results of this type have been used in a study of the influence of operating variables on cell performance and in detecting inherent differences in the operating characteristics of cells of various kinds. Although the information presented in Fig. 2 resulted only with water passing through the cell, the apparatus is suitable for use during flotation of coal when various reagents are present. Possible modi- fications that might prove convenient under special circumstances include varying the size and shape of the receiver and substituting a calibrated, inverted, water-filled carboy or other gas-measuring device for the wet-test meter. If such modifications result in excessive back pressures, some form of draft should be applied at the discharge end of the measuring system.

Jan 1, 1959

By Jan E. Nesset

It is just over 100 years since the practice of blowing small bubbles into a mixture of ground ore and water revolutionized the mining industry, resulting in uneconomic deposits becoming highlyprofitable mines, along with the inevitable lawsuits over this new technology called froth flotation. To this day, the viability of many mining projects rests largely with the ability of flotation to effectively capture the valuable minerals and reject wastes. Remarkably, bubble behaviour in flotation has not been well understood until very recently with the advent of new sensor technologies that can be brought directly into the operating plants. This presentation will review the importance to the mining industry of understanding bubbles, highlight these new technologies and illustrate, with examples, how paying attention to your bubbles will pay off.

Jan 1, 2009

The Interior Department's Bureau of Mines is the Federal Government's primary research arm in the mineral and fossil-fuel fields. In accordance with its Organic Act of 1910, the Bureau's responsibilities have been reinforced since the passage of the Federal Metal and Nonmetallic Mine Safety Act of 1966, the Federal Coal Mine Health and Safety Act of 1969, and the Mining and Minerals Policy Act of 1970. The 1966 and 1969 acts deal specifically with the development of safe working conditions and a healthful working environment for those engaged in the mining industry, while the third sets the national policy as follows: " ... to foster and encourage private enterprise in (l) the development of economically sound and stable domestic mining, minerals, metal, and mineral reclamation industries; (2) the orderly and economic development of domestic mineral resources, reserves, and reclamation of metals and minerals to help assure satisfaction of industrial security, and environmental needs; (3) mining, mineral, and metallurgical research, including the use and recycling of scrap to promote the wise and efficient use of our natural and reclaimable mineral resources, and (4) the study and development of [ ]

Jan 1, 1972

By M. A. Mahtab

This report presents the geometric parameters (attitude, spacing, extent, and aperture) of fracture patterns in a selected portion (study area) of San Manuel copper mine, Arizona. The geometric parameters are quantified for input to structural analyses for studies of the influence of fractures on cavability of ores. Using an orientation analysis procedure developed earlier by the Bureau, three prominent and nearly orthogonal sets of fracture orientations were delineated in the study area. Sets 1 and 2 dip nearly vertically, and generally strike east-west and north-south, respectively, whereas set 3 is nearly horizontal. Both a horizontal rotation (of 14° to 26° for sets 1 and 2, respectively) and a tilt (of 20° for set 3) is shown to occur between the 1415 and 2015 levels of the mine. Gomparison of the three major rock types present in the study area (quartz monzonite, monzonite porphyry, and rhyolite) show that the rhyolite is characterized by short extent, small spacing, and tightness of fractures as well as the general absence of fracture set 3, which may account for its generally observed strong resistance to caving.

Jan 1, 1973

By I T. Tshabalala

In typical conventional narrow vein stoping operations, the use of temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The authors wishes to explore the probability and practicality of making use of new generation support products to make the support operations safer as well as enhance productivity in the stope face. This paper will examine the use of Autorock Drills as a means to drill roof support holes and install appropriate support components into these holes, as well as the application of ?Thin Spray Liners?, commonly called TSL?s as an additional means of creating a safer operating environment. The installation of netting as a means of roof protection and other support aspects such as cemented roof-bolts will also be explored. These proposed items are envisaged to improve the safety of our people and reduce production down time and increase production and productivity.

Jan 1, 2008

By Ellisworth R. Spencer, Lynn A. Alcorn, Peter G. Kovalchik, Adam K. Smith

Noise induced hearing loss (NIHL) is the most common occupational disease among workers in the mining industry. Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90% of coal miners and 49% of metal/non-metal miners have a hearing impairment by age 50. The Mine Safety and Health Administration (MSHA) has determined that continuous mining machines rank first among all equipment in underground coal mining whose operators exceed 100% noise dosage. The conveying system is one of the principal noise sources on continuous mining machines, due to metal on metal impacts that occur between chain flights and the conveyor deck. A highly durable polyurethane coating has been developed for the chain flights to decrease noise generated by these impacts. A continuous mining machine retro-fitted with coated flight bars has achieved overall sound level reductions of 5-7 dB in a laboratory setting. This paper evaluates the effectiveness of this engineering noise control in reducing the noise exposure of continuous mining machine operators in an underground coal mine environment. The results show that the operator of a continuous mining machine utilizing the coated flights receives a predicted 35% reduction in total work shift noise dose.

By Douglas D. Reynolds

Intense vibration can be transmitted to the hands and arms of workers who use hand-held percussive or vibrating devices, tools, and work pieces. Continued habitual exposure to vibration directed to the hands can cause patterns of various symptoms associated with hand-arm vibration syndrome (HVAS). The International Organization for Standardization (ISO) first published ISO 5349 in 1986.3 This standard specified methods for measuring and evaluating vibration directed into the hands from hand-held vibrating devices, tools, and work pieces. The American National Standards Institute (ANSI) published ANSI S3.34 the same year.1 This standard was modeled after ISO 5349-1986 and specified methods for assessing exposure to hand-arm vibration. The Parliament of the European Union has issued the European Union Human Vibration Directive-2002/44/EC, which specifies vibration daily exposure action values (DEAV) of 2.5 m/s2 and daily exposure limit values (DELV) of 5.0 m/s2. These values have generally been accepted by medical experts, scientists, and engineers in governmental agencies, research institutions, and industry in the USA and other countries.2 When they are achieved, they will reduce the potential for the development of symptoms related to HAVS among workers exposed to hand-arm vibration. Significant improvements in measurement and analysis instrumentation, miniature and subminiature accelerometers, and medical diagnostic and assessment protocols have being introduced since 1986 when ANSI S3.34 was first published. In response to these improvements and the introduction of the EU Human Vibration Directive, ANSI Working Group S2.39 developed the revision to ANSI S3.34, which has now been published as ANSI S2.70-2006.2 Method ANSI S2.70 specifies the use of the hand-arm vibration measurement procedures outlined in ISO 5349, Parts 1 and 2.2,4,5 It requires the measurement of ISO frequency-weighted acceleration values in three mutually orthogonal axes of vibration. These values are then vectorially added to obtain the vibration total value, ahv: [ ] where ahwx, ahwy, and ahwz are the measured r.m.s. ISO frequency-weighted acceleration values in the x, y, and z directions, respectively. If multiple vibration exposure events are experienced during a work day, the overall vibration total value is obtained from: [ ] where ahvi is the vibration total value of the ith operation, Ti is time duration in hours of the ith operation, n is the total number of operations, and T is total time in hours associated with the n

Jan 6, 2006

By M. A. Schellhardt

The Bureau of Mines has made periodic back-pressure tests on numerous gas wells in the Texas Panhandle field luring the past several years to study the delivery capacities of the wells under different pressure and operating conditions and to determine the relationships between pressures and rates of delivery from gas wells.4/ However, information regarding the intake capacities of gas-well systems is meager, end in projects involving- the flow of gas into porous-rock reservoirs it has been necessary to determine intake capacities of gas wells by trial. Accordingly the fundamental intake characteristics of natural-gas wells have been studied to develop a method for determining intake capacities under different wellhead pressures from data descriptive of the "output" or producing characteristic of the wells.

Jan 1, 1936

By JOHN HOMER, KATHLEEN STABRYLA, JACOB L. CARR, JONATHAN K. HRICA, JENNICA L. BELLANCA

Given the recent focus on powered haulage incidents within the U.S. mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the research literature is timely. This paper aims to evaluate the maturity of CXS technology through the application of a technology readiness assessment (TRA) to research literature identified by systematic search methods. Results indicate that much of the evidence for CXS performance is at lower levels of maturity: that is, components and prototypes tested in a laboratory and in relevant environments. Less evidence exists for CXS performance at higher levels of maturity — that is, systems evaluated within operational environments — despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for more peer-reviewed research to evaluate CXS technologies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions, which contrasts with haul truck fatal accident statistics that indicate most are due to vehicle-to-environment interactions, such as traveling through a berm. Lastly, the relatively small number and segmented nature of relevant studies suggest there is a need for more incremental research that would better facilitate the improvement of CXS technologies. This progression could be achieved through continued long-term interest and support for CXS technology research.

Mar 1, 2023

By Zoran M. Stevic, Mirjana M. Rajcic-Vujasinovic, Zvonimir D. Stankovic

"Huge electrochemical investigations have been performed on Technical faculty in Bor (Serbia) which main goal was the clarification of the copper sulfide minerals behaviour in hydrometallurgic and flotation processes. Modeling of these processes was a part of the effort for better understanding of the reaction mechanisms.The consideration of electrical analog circuit and mathematical model of processes at interfaces copper sulfide/electrolyte (CuS/(CuSO4+H2SO4), Cu2S/H2SO4 and CuFeS2/H2SO4), based on studies of the overvoltage – time transients, will be presented. The transients were obtained using single pulse galvanostatic method and electrochemical cell with standard three electrode assembly. In that goal it was developed an original system for computer measurements that enables the application of several methods for electrochemical investigations (galvanostatic, potentiostatic, cyclic voltammetry, electrochemical impedance spectrometry etc). The system was tested and adjusted using commercial electrochemical equipment made by AMEL, Milano.In the first stage of consideration the different equivalent electrical circuits have been tested by computer programme OrCAD 9.2 in order to identify the circuit with responses equivalent in shape to experimentally obtained ones. In that way it was established a configuration of an analog electrical circuit for investigated electrochemical system. That phase enabled only very rough determination of values of circuit components and their relative ratio.In the second stage the method for determination of all elements of electrical analog circuit is described. It is based on mathematical consideration of a given circuit on one hand, and valves of the overvoltages at selected times, obtained from charging and discharging parts of galvanostatic transients, on the other."

Jan 1, 2003