Search Documents

By Karina Forster

Rock mass characterisation is a critical component of effective stope design. Unexpected excessive stope dilution or uneconomic stope sizes can be the result of rock mass characterisation that is not representative of actual stope conditions. Comprehensive characterisation of the rock forming the stope hanging wall, back, ends and footwall is best done by a rock mechanics or ground control expert, however, this is time consuming and is often limited by available access. There are two general approaches for characterising a stope hanging wall for dilution estimating. Detailed classification and mapping data can be collected in local areas where good exposure is available. Personnel, exposure and time are usually not available to do a thorough analysis for all stopes. The stope hanging walls are then broken into lenses or domains and similar conditions are assumed for each area. The second approach consists of using readily available data such as RQD. Other rock mass properties which influence hanging wall behaviour are estimated based on back analysing a few case histories. Stope design is then based on the variability of the one parameter, such as RQD, that is consistently measured for the rock mass surrounding the ore body. This paper presents a third approach which looks, in depth, at the interpretation of geological core logging data for rock mass characterisation. Several rock mass properties that influence stope design, such as joint alteration, rock mass strength, joint spacing and orientations, have been linked to data collected by the mine geologists. This drill hole logging data was calibrated against underground mapping and used to back analyse the dilution prediction for mined-out stopes.

May 1, 2006

By Emad Farouz

The resistance of very dense glacial outwash formations consisting of sand, gravel and cobble formations can be quite high, and techniques for measuring the strength and deformation properties often cause engineers to underestimate the strength of these layers in drilled shaft design. More realistic measurements of this dense formation can be achieved with slotted steel casing pressuremeter tests. To minimize disturbance and achieve accurate measurements, drilling a pilot hole prior to probe insertion is necessary. Characterizing geologic formations that contain significant amounts of gravel and cobbles is challenging because of scale factor. Inserting a standard pressuremeter probe into this formation without damaging the membrane is difficult. This paper presents a case study for the IR-75 project in Dayton, Ohio, USA, where these dense materials were characterized using a slotted casing pressuremeter, optimizing design by providing more realistic properties of these materials.

Jan 1, 2006

By J. A. Bakken, M. Tangstad, P. A. Eidem

In the submerged arc production of ferromanganese, sillicomanganese and ferrochromium, the coke bed characteristics play an important role. The basic mechanisms of electric current conduction in the coke be dare not yet fully understood, but important parameters are the material resistivity of coke and the contact resistance between the coke particles. Preliminary tests indicate that the contact resistance is of great importance to the bulk resistance of the coke bed. An apparatus measuring the material resistivity and contact resistance of carbon materials has been developed. Both graphite and industrial coke have been tested. The material resistivity tests were performed on single particles to ensure that the effects of pores and cracks were included and the contact resistances were excluded. Two geometries were tested to obtain the contribution of the contact resistance to the total resistance of two connecting particles. The tests were performed in an inert atmosphere at temperatures and current levels found in industrial submerged arc furnaces. The results show that the method has a satisfactory reproducibility. It was found that the contact resistance is about 10 times higher than the resistance of the material when two particles are in perfect contact and that the resistivity of SSAB coke is more than 10 times higher than that of the graphite at room temperature, but with increasing temperature the difference decreases. For SSAB coke the general trend is that both the resistivity and the contact resistance decrease with increasing temperature.

Jan 1, 2007

[Ferro Alloys Producers Association The South Africa Institute of Mining and Metallurgy www.saimm.co.za Mintek www.mintek.co.za Eskom www.eskom.co.za ]

Jan 1, 2004

By Scott C. Brown, Ivan U. Vakarelski

The particles commonly encountered in mineral benefication schemes have irregularites that are expressed at many different length scales. In part, this originates from preceding processes (e.g. makedown, comminution, handling and storage), which are known to chemically and physically modify the bulk particle and its surface. Interparticle tribology, dissolution and reprecipitation events along with large-scale mechanical stresses are just a handful of the interactions encountered during processing of particles prior to separation. It is feasible to imagine that each one of these events may impose a fingerprint of characteristic nanoscale, microscale, and macroscale morphological changes that can modify the overall interaction of these particles within a system. Suprisingly there are just a few works on how these resulting features can alter the performance of benefication schemes, and especially flotation.

Jan 1, 2003

Reduce the respirable dust exposure of the roof-bolter operator when downwind of the continuous miner, particularly in mines where respirable dust standards are more stringent because of silica in the respirable dust. Dust Sources If roof-bolter dust levels are excessive, the bolter dust collector should first be checked to ensure that it is operating properly. (Technology News No. 219 provides information on how to spot and repair bolter dust collector problems). If the roof-bolter dust collector is operating properly and dust levels are still excessive, then the source is most likely a continuous mining machine operating upwind. In many sections, the roof-bolter operator must work on the return side of the continuous miner during part of the production cycle. In three-entry longwall developments with single split ventilation, this may happen as much as one-third of the time. Factors which pro-mote high quartz dust exposure are:

Jan 1, 1985

By Brad Marchant, Rick Lawrence, David Kratochvil

"BioteQ has successfully developed commercial operations for ARD treatment and selective metal recovery using the patented BioSulphide and Thiopaq® biological reduction technologies. The BioSulphide-Thiopaq process was developed to provide biogenic sulphide for the selective recovery of high purity metal concentrates from acidic wastewater, which are sold to recover capital costs and off-set water treatment costs. The BioSulphide-Thiopaq process can be used on a stand-alone basis or in conjunction with a lime circuit. Process advantages include: selective recovery of metals, very low metal concentrations in effluent, reduced waste sludge liability, reduced lime treatment costs and, in some cases, profitable sale of metal concentrates. Two case studies are presented to illustrate operations focused on metal recovery at the Caribou Mine, New Brunswick, Canada, and at Phelps Dodge, Arizona. A third case study is presented to highlight environmental control as well as metal recovery for treatment of ARD at the Raglan Mine in Northern Quebec. Process flowsheets, capital and operating costs are presented for the three case studies.INTRODUCTIONProtection of water quality has become one of the most important environmental challenges facing the mining industry. Although new mining projects can be designed to minimize impacts to the environment, many existing and abandoned mining operations have water quality problems. The principal cause of water contamination is acid rock drainage (ARD), which is generated when residual sulphide minerals in waste rock, tailings and other mine components and products are exposed to air and water. These reactions can produce acidity and elevated concentrations of metals in drainage and seepage that can adversely affect surface and groundwater resources. To meet regulatory criteria for water quality in the receiving environment, many mine operators must consider treatment of mine water and other effluents prior to discharge."

Jan 1, 2003

By F. C. Wagner, E. P. Klier, D. E. Nulk

The presence or absence of plastic strain at a cleavarage surface is a question of much importance, and upon its answer depends future possible theoretical work. To investigate this question back-reflectinn X ray patterns were obained on the cleavage facets of ferrite grains. The test set-up consisting of FeK colli- mated radiation, single grain material and stationary cassette and specimen will not lead to a diffraction pattern, in general, but is an ideal arrangement for the exami-nation of surface effects. A pattern taken on hydrogen purified

Jan 1, 1949

By Peter B. Lilly

Thank you, Syd, for the kind introduction and for inviting me to give the Keynote Address at this very prestigious gathering of some of the finest intellect and talent in the domestic and international coal industry. CONSOL Energy has been a part of this conference for its entire 24-year existence. We have presented 27 papers over that time. CONSOL employees have also been members of the planning committee for the conference, and we have been pleased to support the event both financially and with many participants. So I am honored to be here with all of you this morning, especially during such a positive period for coal. You can just feel the enthusiasm in this room for our industry, and for this conference. I can tell you, there?s also a lot of enthusiasm and excitement in CONSOL Energy?s boardroom. And our enthusiasm is mirrored on Wall Street. But there remains an ironic twist to all of this attention. Even when times are good, the coal industry seems to go largely unnoticed by the mainstream. Outside of West Virginia and other coal-producing regions, the industry still seems to lack influence and support, at least here in America. As an example, last month, an ABC News crew visited our Blacksville 2 Mine, near here, to do a feature story on increased employment in the coal industry.

Jan 1, 2006

By John Organiscak

A majority of continuous mining machines employ a water spray system and a machine mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays, and scrubber airflow on dust and gas levels while using a 12.2 m (40 ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1 m (20 ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complemented the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut as compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010

By K. N. Han, N. S. Kim, H. Yoon, J. S. Sohn

The leaching behavior of silver and silver oxides in ammonical solutions has been studied. The current study is concerned with an effective recovery of silver from secondary sources such as spent silver batteries. Silver associated with these batteries appears in various forms including metallic silver, argentous oxide, Ag2O and argentic oxide, AgO. The leaching behavior of metallic silver in ammoniacal solution has been studied using an electrochemical mehtod. Oxidants used in this study include hyperchlorite, hydrogen peroxide, bromine and iodine. Results on cyclic polarization and Tafel plots on the silver anode in ammoniacal solutions are presented and the results are discussed. The dissolution rate of metallic silver in ammoniacal solutions is also compared with those of silver oxides.

Jan 1, 2002

By J. C. Kingston

Introduction The sliding-form method of erecting concrete structures was first devised and used in the early part of this century by the Sante Fe Railroad Company for the erection of a grain elevator at Santa Fe, New Mexico. A somewhat related principle has been employed for a number of years in shaft lining work and, to our knowledge, was perfected in Butte, Montana, but until the building of the concrete headframe at the Jeffrey mine of the Canadian Johns-Manville Company, Ltd., at Asbestos, Que., the method, as applied to surface structures, was quite foreign to the mining industry in Canada. The current shortage and cost of structural steel shapes has no doubt contributed more than any other single factor to the investigations that have led to the use of reinforced concrete as a headframe building material. Mining men in western Quebec and northern Ontario have shown a great deal of interest in the design and construction of the headframe at the East Sullivan mine in Bourlamaque township, Que., and we have had many queries regarding the methods used and, in particular, for an explanation of the sliding-form principle. This article is written in an attempt to set forth the conditions which were to be met; to explain the construction methods used, and to discuss the economy of concrete headframes as compared with the conventional steel structures with which the mining fraternity is familiar.

Jan 1, 1949

The mining licence for the Macraes gold mine places emphasis on the progressive rehabilitation of the land to a state compatible with the landscape and environment that existed prior to mining activities taking place. The shallow soils and hostility of the environment dictate that choices of plant species should focus on persistence rather than high productivity, choices that are made easier by observing the vegetation patterns that have developed naturally within the area, by recontouring landforms to integrate with the surrounding countryside and the use of appropriate plants and establishment techniques.

Jan 1, 1992

By P Holtham, K Duffy, W Valery, A Jankovic

In the face of increasing energy costs, limited water resources, more stringent legislation, and lower feed grades, the mining industry is searching for more sustainable technologies and practices. Metso Process Technology and Innovation (PTI) is undertaking a research project, ‘improving the resource and eco-efficiency of mining operations’, to help the industry meet these challenges. The project is investigating alternatives in mining and processing that reduce energy and water consumption, minimise emissions and waste, and maximise the value recovered from the deposit. The targets are to reduce energy usage by more than 30 per cent and greenhouse gas emissions by more than 50 per cent compared to current practice.Key areas of interest were identified across mining and processing operations. These were grouped into the following interrelated work areas for investigation: high intensity selective blasting, in-pit crushing and conveying, preconcentration, energy efficient comminution circuits and technologies, coarse particle flotation, and water recovery optimisation. Investigations have included reviews of industrial data, modelling, simulation, and laboratory and pilot scale trials. In some areas industrial scale trials will commence shortly. This paper discusses the investigations and key findings from the project so far; highlighting the possibilities for reducing energy consumption, water usage and carbon emissions. A particular mining process may incorporate any combination of the alternatives identified and requires tailored solutions based on a detailed understanding of the ore deposit, the process and local conditions. The focus is on improving resource efficiency; creating more value with less impact and consequently a better economic return from the available resource. Technologies exist today that can transform mining into a more efficient industry for tomorrow.CITATION:Duffy, K, Valery, W, Jankovic, A and Holtham, P, 2015. Resource efficient mining processes of tomorrow, in Proceedings Third International Future Mining Conference, pp 227–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Piotr Litwa

The paper focuses on actions aiming at improvement of work safety in mines, particularly in those extracting hard coal, taking into account the characteristics of natural hazards in Polish underground mining and the reasons of mining disasters connected with those hazards. It refers to conclusions addressed to scientific and research centres, drawn during last decade by Commissions appointed by the President of the State Mining Authority in order to investigate reasons and circumstances of incidents, which till now, could not have been accomplished because of financial reasons. Furthermore, the paper presents basic assumptions of the Strategic Research Project Improvement of work safety in mines, announced by the National Centre for Research and Development at State Mining Authority?s President request.

Aug 1, 2013

By H. Lieberwirth, M. Klichowicz

The comminution at grain size level for the liberation of valuable minerals usually requires the highest size-specific energy. Therefore, the full understanding of the comminution process at this level is essential. Models based on the Discrete Element Method (DEM) could be a helpful tool for this purpose. In those, the mineral microstructure, which has a dominant influence on the fracture behaviour, can be described in great detail. One major concern, however, is the missing representativeness of simulated models. In this study, a method to overcome this limitation is presented. The authors show how a realistic microstructure can be implemented into a particle bed comminution simulation using a two-dimensional Bonded Particle Model (BPM). The improved algorithm based modelling approach is exemplarily compared to an equivalent real experiment. Thereby, the focus is set on the analysis of the interfacial breakage and the capability of the simulation to reproduce the experimental results. The comparison of the results shows that simulations at grain size level allow a more detailed evaluation of the fracturing behaviour. This is of special interest as the aim of comminution in mineral processing is not only the size reduction of coarse particles, but an efficient liberation of the valuable components. Hence, simulations with automatically generated real mineral microstructures will help to further improve the efficiency of ore processing. Keywords: Discrete Element Method, grain modelling, particle bed comminution, realistic synthetic

Jan 1, 2020

By C A. Heinrich, J L. Walshe, V J. Wall

The Porgera Gold Mine, located in the highlands of Papua New Guinea, has produced over 5 million ounces of Au, since its opening in late 1990. The deposit is located within Upper Cretaceous Papuan Platform sediments approximately 25 km south of the Lagaip Fault, and is spatially and temporally associated with the 6 Ma alkaline Porgera Intrusive Complex.

Jan 1, 1995

By F. G. Pickard

"The Strathcona Concentrator is one of three concentrators presently operated in the Sudbury District by the Nickel Division of Falconbridge Nickel Mines Limited. Production commenced in 1968 at a milling rate of 6,300 tons per operating day. Milling capacity was increased in 1970 to 7,200 tons per operating day. 7he ore contains iron, nickel and copper primarily in the form of pyrrhotite, pentlandite and chalcopyrite, while the common gangue minerals are feldspar, quartz, mica, talc and chlorite. The primary function of the concentrators is not only to liberate sulphides from silicate gangue minerals but also to separate pyrrhotite from the more valuable minerals pentlandite and chalcopyrite.SummaryExcessive wear on steel liners and blinding of grates in a regrind pebble mill of the Hardy Concentrator was corrected by the use of rubber liners and grates. The success of these resulted in their installation as original linings In all grinding units except the rod mills at the Strathcona Concentrator. The operation of rubber liners and grates when sized mine ore was used as the grinding medium was satisfactory confirming the Hardy Concentrator experience. Problems developed when the grinding medium was changed from sized mine ore to steel balls in that blinding of the grates occurred. This resulted in conversion of the units to overflow type mills through removal of the grates. The lifter bar life was significantly increased by using higher lifter bars.Grinding PracticeOperation of a regrind pebble mill commenced in 1961 in the Hardy Concentrator. This operation demonstrated the economic feasibility of using sized mine ore as grinding medium. Problems caused by excessive wear of metal liners and grates combined with blinding of the grates were corrected in 1964 through installation of rubber liners and grates."

Jan 1, 1974

By Marion Loomis

Environmental regulation is an ever growing cost to the mining industry. Requirements for such items as air quality modeling, hazardous waste disposal, selenium concentration in water and sagebrush planting consume more of the mining industry’s resources each year. The mining industry is willing to make the necessary financial commitments to assure that the air, land and water resources are adequately protected and restored. However, it is sometimes difficult to explain to management and stockholders why money should be spent on a specific issue when science and common sense indicate it is being wasted. Common sense and sound science should dictate how mining is regulated.

Jan 1, 1994

By Martin J. Gavin

"Before discussing oil shales it may be well to consider briefly the conditions surrounding the petroleum industry in the United States, because these largely explain why so much interest is being manifested in oil shales. The United States is not only the greatest producer of petroleum in the world, its output amounting to about 65 per cent of the world's total production; but is also the world's greatest consumer, using more petroleum than it produces within its own borders. For the past four or five years it has been necessary to import oil at a continually increasing rate to make up the deficit between domestic production and domestic consumption. Experts who have made a close study of the future supply and demand for, crude petroleum are satisfied that under present production practice and with the development of possible undeveloped productive areas, the gap between domestic consumption and production will steadily .increase.As possible solutions for the impending domestic shortage of oil, various expedients are receiving attention. These may be grouped under three heads, as follows:(1) Temporary measures, such as curtailment of consumption, development of more efficient methods of production, and more efficient utilization of supplies of petroleum still available. It is unlikely that there will be any great curtailment in consumption of petroleum in the United States; rather, consumption will continue to increase unless a real shortage of oil actually forces curtailment of consumption. The other two possibilities mentioned deserve, and are resolving, serious thought. Much experimental work along these lines, some of which has already yielded excellent results, is being done. Obviously, however, any of these remedies are temporary ones only, so far as regards domestic production of petroleum."

Oct 1, 1920