Search Documents

By S M. J Koleini, F Hedjazi

The purpose of this research was to study the calcination of lead-zinc flotation tailings from the Angouran lead and zinc flotation plant in Iran as a pre-concentration step prior to hydrometallurgical processing of the oxidised tailings. There is an abundance of these tailings in the Angouran region and making use of these tailings would help preserve national wealth and also reduce the serious problems of environmental pollution caused by the tailings. At the optimal conditions of calcining at 750 - 800¦C for 45 minutes, the sample showed a mass loss of about 19 per cent. Mineralogical analyses showed that under these conditions the carbonate minerals including smithsonite (ZnCO3), calcite (CaCO3) and dolomite (Ca Mg (CO3)2) decomposed to their respective oxides. Hemimorphite (Zn4Si2O7 (OH)2.H2O) converted into willemite (Zn2SiO4) and this transformation postponed the formation of silica gel in the leach solution. The grade of zinc increased from 22.20 per cent to 29 per cent. These mineralogical changes resulted in desirable reactions in the acid leach process.

Jan 1, 2004

By J. -W. Kim, Y. -B. Kang, H. -G. Lee

The effect of SiO2addition on the decomposition of Li2CO3was investigated at temperatures up to 1000ºC. It was found that addition of SiO2greatly enhanced the decomposition of Li2CO3. The main decomposition reaction started at around 600ºC, and completed just above the melting point of Li2CO3. The major decomposition product was Li2O?SiO2irrespective of the Li2CO3to SiO2mixing ratio while both reactants were available. It was ascertained that a liquid layer betweenLi2CO3and SiO2particles formed and facilitated the decomposition reaction. The governing reaction of the decomposition was the one between the dissolved Li2CO3and SiO2in the liquid layer to form Li2O?SiO2. The decomposition rate was independent of the Li2CO3/SiO2mixingratio until either one had been completely exhausted. When excess Li2CO3existed, it further reacted with the initial product of Li2O?SiO2to form 2Li2O?SiO2. When SiO2was found in excess, on the other hand, no further reaction took place. This is attributed to the fact that uponLi2CO3exhaustion there is no liquid phase available to facilitate further reaction. The apparent activation energy of the decomposition of Li2CO3in existence with SiO2is 198 kJ mol-1.

Jan 1, 2004

By A. R. Miller, G. Desrivières, T. MacKinnon, H. Bursey, M. C. Bétournay, B. Replogle, D. L. Barnes, P. Laliberté

"A mine production locomotive, the world’s first applied industrial fuel cell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuel cell vehicles.The locomotive’s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuel cell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery- powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuel cell vehicles, and cost benefit aspects.This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable, and efficient power plant that fulfilled its design objectives, including longer productivity time for a given vehicle fill-up."

Jan 1, 2004

By L. Katgerman, E. N. Straatsma, Suyitno

"Single-roll strip casting process is studied using computational fluid dynamics which takes into account fluid flow, heat transfer and solidification. The computational model is based on the conservation Jaws of momentum, energy and continuity. Correlation of strip thickness, solidification zone length, and puddle shape on single-roll strip casting of Al-1 %Mn is explored. Feeding pressure and roll speed are investigated. The results show that the··strip thickness slightly increases with pressure, similarly the length of solidification zone. The variations of strip thickness and solidification zone length with roll speed show a sharp decline for strip thickness and slight decline for the length of solidification zone with increasing roll speed. The constraint and free-jet flow have different feature in term of flow field. Severe turbulence is observed on the free-jet flow.IntroductionThe near-net shape casting of strip metals is a demand nowadays. The demand is particularly stimulated by the challenge to become more competitive through enhanced performance. The improvement in the existing processes and new innovative technologies are introduced by the metal industry to gain better product quality, more efficiency in energy consumption, low throughput, yield and operating costs [1-3].There are many advantages that can be obtained by the direct casting of strip. The most prominence is the elimination of hot rolling. Beside that the high rate of heat extraction associated with strip casting offers the possibility of a finer, Jess segregated cast structure. The microstructure will result in the improvement of mechanical properties compared to conventional material, or alternatively the opportunity of using grades of metal outside the normal range for continuous casting.The concept of single-roll strip casting has been difficult to commercialize, because of the complex interactions between fluid flow, solidification, shrinkage, and stress, which lead to serious quality problems. Besides that, the quality and the thickness of the strip are affected by the thermal properties of the strip, roll cooling conditions, roll geometry, and other process parameters. To understand how these parameters affect the strip formation, some researchers have modeled the process [4]."

Jan 1, 2004

By A. C. Ter-Oganesyants, N. N. Anisimova, G. P. Kotukhova, G. N. Dylko

The process utilized at Norilsk Nickel Polar Circle Division for treating slimes from the electrorefining of copper and nickel was developed in the late nineteen fifties and has survived without any fundamental changes. This technology is a combination of pyro and hydrometallurgical operations to produce PGM concentrates that are sent away for refining. The characteristic feature of the current technology is multiple-stage, extended cycle treatment with significant incomplete production, low labour and automation efficiency and poor hygiene and sanitary conditions. To eliminate all negative aspects mentioned above, specialists of Norilsk Nickel Polar Circle Division have developed a new hydrometallurgical process for treating electrolytic slimes. The main steps of the flow sheet developed are autoclave leaching of the slimes and electrochemical opening-up of a cake from autoclave leaching. The implementation of the new process will allow Norilsk Nickel Polar Circle Division to shorten the process cycle 4-5-fold thus reducing the volume of incomplete production, considerably increase labour efficiency, simultaneously improving working conditions, upgrade the final concentrate, reducing costs and increasing PGM recovery during refining and, ensure higher security of precious metals by employing automated processes and vacuum sealed units.

Jan 1, 2004

By James Pile

Since C.C. White introduced coalmine roof trusses in 1967. many different systems have evolved. Beginning in the mid 1990's, several types of bar/cable truss systems have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, this new truss increases operator safely. In order to fully benefit from the new truss system, a closer look at the individual components and their interaction was undertaken to understand critical implications on preload and overall support capabilities.

Jan 1, 2004

By R. I. Rodriguez

Since the 1973 energy crisis, high fuel oil costs have been eroding the economics of the Nicaro and Punta Gorda Plants that employ the Caron Process for laterites processing. Since 1995, Cuban crude oil production has growth dramatically, with progressive utilization in power generation, cement and nickel plants. This paper shows how Nicaro and Punta Gorda plants have been able to shift from expensive Bunker C Fuel Oil to heavy but cheaper Cuban Crude Oil of high Sulfur content and achieve a significant reduction in operating cost. Problems related to the high sulfur content of the Cuban crude oil have demanded extensive investigations of the process chemistry and novelty solutions are proposed, with corresponding changes in process conditions. Innovative options are shown that will allow further cost reductions in the future. Keywords: Cuban Crude Oil, Sulfur, Ammonia.

Jan 1, 2004

By Alexander Malahoff

Field observations and sampling of land-based and submarine hydrothermal and geothermal sites show a definite link between the geological setting, fluid geochemistry and specialized assemblages of microorganisms found at these settings. Three initial sites have been chosen as a basis for these studies. The first site is located on hydrothermal vents in pit craters on the submarine volcano Lo?ihi (Hawai?i) at a water depth of 1,300 meters. The second site is within the geothermally active vents, ponds and lakes of the Taupo Volcanic Zone of New Zealand. The third site extends along the chain of volcanically and hydrothermally active volcanoes of the Kermadec-Tonga arc and back-arc system. To focus our work in New Zealand, a geomicrobiology field and experimental center has been established in Wairakei, New Zealand, with the relevant genomics, proteomic and bioinformatics work being conducted at the University of Hawaii. As part of a partnership between the University of Hawai?i, the Institute of Geological & Nuclear Sciences (GNS) and Victoria University of Wellington, a new interdisciplinary graduate course in geomicrobiology will be taught at Victoria University beginning next year. Since mineral-microbial interactions have been occurring for the past few billion years and these interactions have led to where one generates the other, a metal-bacteria research program has been initiated at GNS using arsenic-gold and other metal-bacterial interaction processes as a research objective. In this research program, we have completed the full genome of a new species of marine bacterium Idiomarina loihiensis from the Lo?ihi hydrothermal vents and identified specialized microorganisms living in pH 0.3 geothermal vent waters of White Island, New Zealand. The multidisciplinary approach to study the process of accumulation of metals in the hydrothermal systems clearly shows the path of how bacterial-mineral interaction can precipitate metal deposits. These studies will lead to new avenues for biomining, bioremediation and the understanding of the origins of life.

Jan 1, 2004

By J. Janssens, B. Coletti, S. Smets, J. Plessers

The oxygen activity of the ladle slag determines the reactivity towards the steel during ladle treatment. Therefore, the in situ measurement of the oxygen activity of slags can be an important tool. The applicability of an electrochemical sensor is examined in this work. The sensor measures the electromotive force (EMF) that is established between a sample of the slag phase that is immersed in the liquid steel bath and a reference system (Cr/Cr2O3). Industrial and laboratory experiments demonstrated the capability of the sensor to detect the influence of the slag components on the measured oxygen potential. Comparison of the measured values with thermodynamically calculated values shows that the measured oxygen activity is systematically too low. This was attributed to a reaction of the steel with the slag sample. To investigate this, further lab tests were performed where the slag oxygen activity was measured after the slag had been equilibrated with the steel. The measured values were dependent on the oxygen activity (aO) of the steel. For industrial applications, it is concluded that the aO of the steel should be known and that this value is necessary for the interpretation of the measured values. Keywords: low carbon steels slags, slag oxygen activity, on-line sensing, thermodynamic evaluation.

Jan 1, 2004

By M. L. Tucker, William H. Langer

Many countries, provinces, territories and states in the European Union, Australia, Canada, the United States and elsewhere have begun implementing sustainability programs. Most of those programs, however, stop short of sustainable management of aggregate resources. Sustainable practices do not always have to be conducted under the title of sustainability. This case study describes how Lafarge implemented the principles of sustainability even though there was an absence of existing local government policies or procedures addressing sustainable resource management. Jefferson County is one of three counties in the six-county Denver, CO, region that has potentially available sources of crushed stone. Crushed stone comprises 30percent of the aggregate produced in the area. And it plays a major role in regional aggregate resource needs. Jefferson County is home to four of the five crushed stone operations in the Denver region. Lafarge operates one of those four quarries.

Jan 1, 2004

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Current industrial compacting and briquetting practices are largely based on trial-and¬error techniques. This paper introduces a two dimensional finite element model of compacting/briquetting process in the roller press. Compared with other modeling techniques used in the past, finite element method offers the most versatile approach because it incorporates adequate information about powder behavior, geometry and frictional conditions and offers predictions for the density distribution, velocity field, stress distribution, roll force, roll torque and other important process variables. More over, when the model includes elasticity, it offers predictions on the internal stress state in the briquet after its exit from the pressing zone. This enables to perform realistic computer experiments which are helpful for establishing the pressing system design, forming cavity geometry and process conditions necessary to produce compacted or briquetted product with the desired properties.

Jan 1, 2004

Over the last two decades, the mining industry has spent considerable time and effort in installing sophisticated control systems (including expert systems) to regulate and improve the performance of AG/SAG mills. Yet the need for these systems is often overlooked – unmeasured and uncontrolled variation in the feed material. With AG/SAG mill technology replacing rod and ball mills as primary grinding equipment, the need for careful and thoughtful feed preparation has gone. To maximise mill throughput, operations need to better understand the ore characteristics affecting AG/SAG mill performance. Industrial operating data will be used to illustrate these ideas and concepts. It is often quite surprising which ore characteristics that are the most influential on mill throughput.

Jan 1, 2004

By M. Y. Wong

Electronic detonators have been used on a trial basis for over a decade, and found more recent application in production blasting as well. The relative merits of these detonators and their applicability are outlined through examples from actual blasting operations. They offer unprecedented flexibility in the design of mass blasts and in control of vibration and blast-induced damage. However, the drive towards replacing the pyrotechnic detonators by electronic ones in general could prove to be counter productive without a re-examination of prevailing blasting practices. In fact, such an approach tends to blur the tremendous potential of the electronic detonators in redefining many standard blast designs and practices.

Jan 1, 2004

By J. Persson, N. G. Bliss

Electric furnaces used for smelting and those used for scrap melting exhibit different performance profiles in terms of electrical characteristics. However, the underlying principles are the same for either case. The rationalization of these variables is a major concern for furnace operators and designers. This paper presents the results of a two year study of high speed real time data from a number of electric furnaces around the world, covering a very wide range of design philosophy and product manufacture, to provide a better mathematical insight into rationalizing the furnace operation.

Jan 1, 2004

By G. Ergin

The interactions taking place between Al-Mg alloys and the bed media during aluminum filtration are not yet well understood. These interactions were studied using the infiltration technique. The reaction interface was analyzed using different techniques such as SEM and TEM. Only spinel formation was observed at the interface regardless of the type of alumina and contact time. This paper discusses the results of the study.

Jan 1, 2004

By Q. F. Wang

Spontaneous combustion hazard of loose coal in the top-coal caving region of entry affects the safety of the entry and top- caving longwall face seriously. In this paper, by combining on- site temperature tests with lab tests and numerical simulation, the characteristics of microcirculation close to the top-coal caving region are analyzed. A model for the temperature fields of the microcirculation in loose coal is presented. Based on this model, the temperature distribution and possible self-ignition region can be predicted. Further, the heat and mass transfers in microcirculation are studied. Finally, the mechanism of oxygenation during the spontaneous combustion of microcirculation in loose coal of the top-coal caving region of entries is put forward. The research results in this papa may provide ideas for the prevention and putting out of the fire caused by spontaneous combustion in the caving zone.

Jan 1, 2004

By M. G. Wimberger

The Merensky Reef zone, as developed on Impala Platinum?s Rustenburg Operations, displays a gradational mineralized zone, with grades decreasing from the Merensky Pegmatoid Unit into the footwall and hanging wall. A system of identifying a manageable method of defining the mining cut is introduced, termed the grade profile attenuation cut-off grade. Although horizontal grade selectivity is not applied in the mining of the Merensky Reef zone, low extraction of the orebody, due to manageable and non-manageable factors, can contribute to a reduction in revenue, even losses, due to fixed cost contributions in the mining and beneficiation of the ore. A model is proposed that integrates all variables affecting the revenue of the mining operation, including the grade profile attenuation cut-off grade, the extraction factors, commodity prices and exchange rates, utilizing numerical simulation techniques in a PC-based environment. A breakeven extraction factor for a specific cut-off grade is delivered for a range of market conditions. The breakeven extraction factor is a useful guide when designing mining layouts in structurally complex and low metal content areas. Incorporating distribution functions for individual commodity prices and exchange rates into the model provides mineral resource managers with a risk profile for individual mining areas. Shaft areas have varying grade profiles and each area should have individual models run, to prevent generalizations being made about acceptable risk levels on mining areas.

Jan 1, 2004

Several inorganic reagents and organic polymers were tested as depressants in the single mineral flotation of ultrafine iron oxide and hydroxylapatite with Dowfroth 250 as a frother. It was observed that the inorganic reagents and the low molecular weight polymers generally caused dispersion of the ultrafine particles, and consequently their recovery into froth products more or less equaled the recovery of water. On the other hand, the high molecular weight polymers caused different degrees of flocculation of the ultrafine particles, and their recoveries were much lower than the recovery of water. These observations pointed to a need to re-define flotation depressants in fine particle flotation. The traditional definition of a flotation depressant, i.e., to make particle surfaces hydrophilic by forming a hydrophilic film and/or by removing collector and activator coatings, is sufficient for relatively coarse particles. However, to prevent fine and ultrafine particles from floating, a successful depressant should not only make the particles hydrophilic, but also enlarge the particle sizes so that they do not enter the froth product by mechanical entrainment. Polymeric depressants are ideal for these purposes. The different schemes to use polymeric depressants in the selective flotation of fine and ultrafine particles were discussed These schemes involve the integration of the polymeric depressants into other size enlargement processes such as shear flocculation, oil agglomeration, etc., for hydrophobic particles.

Jan 1, 2004

By O. Akinkugbe

The safe, productive exploitation of coal in multiple-seam situations requires specific design technology. At present, there are two general design approaches that the mining engineer can use to analyze the multiple-seam problem in question, either simple empirical relationships or complex numerical models. Often, the empirical approaches are too general for the specific problem and the numerical models require too much time and expertise for the practicing engineer. In this paper, a new program designed for quickly and easily calculating the stresses, strains, and safety factors associated with basic multiple-seam mining situations is presented. The program implements a simplified, two-dimensional boundary-element method in order to model the complex multiple-seam stress and displacement interactions. The program incorporates automatic coal and gob property generation to simplify the input, and inherently calculates pillar safety factors to enhance the output.

Jan 1, 2004

By B. Friedrich, N. Anastasijevic, S. Stopic

The extraction of nickel from Serbian and Western Australian lateritic ore by sulphuric pressure acid leaching (PAL) has been studied. The following parameters were tested: stirring rate, acid to ore ratio, reaction time, pressure and temperature. These studies were performed with ore samples from the Rudjinci, Serbia and Silcrete, Australia, both belonging to the laterite-silicate group of deposits. An increase of the reaction temperature and the stirring speed at a fixed acid/ore ratio showed a positive influence on nickel extraction. The decrease of the oxidation potential with time correlated with the increase in Fe(II) in solution and nickel extraction as the reaction went to completion for both ores. The target values of 95 % Ni extraction and 60 % Co extraction were attained in 5 min at 250°C for the Serbian silicate ore, at an agitation rate of 1500 rpm, 10 % solids, and acid/ore ratio of 0.40. Under similar conditions only 60 % Ni, but 69 % Co could be extracted from the Australian Silcrcte ore due to different mineralogy. The nickel extraction was shown follow a diffusion-controlled reaction model.

Jan 1, 2004