Search Documents

By Xu Zhang, Xuewei Lv, Guibao Qiu

Slag foaming phenomenon is of vital importance to the mass and energy transfer in metallurgical processes. A considerable extensively studies carried out via out-gas in the past cannot simulate well the foaming phenomenon formed in the blast furnace where high TiO2 iron ore is used. A gas reaction was designed in the water-glycerol system to simulate the inner-gas system. This study investigated the influences of solution viscosity, particle concentration and particle size on foaming caused by endogenetic gas. The results show that the foaming height decreases with the increase of solution viscosity, which means reduced foaming ability, more difficult foaming elimination process and prolonged time for natural defoaming. With increasing the solid particle content, the foam height presents a trend which increases firstly and then decreases. Under a certain solid particle content, foaming height decreases with the increase of solid particle size, indicating a weak foaming ability.

Jan 1, 2015

By Andrew L. Puwis

Methodologies were presented for computing the thermal gradient associated with single crystal solidification in macroscopic computer modeling. The. heat transfer, and solidification of a shaped investment casting model were simulated using properties from three different alloys. Following the simulation of solidification, the resultant thermal gradients (G) and rates of solidification (R) from representative points were extracted in various ways and compared: It was discovered that alloy properties have a strong influence on the computed thermal gradient and rate of solidification for the three methods investigated. Data also showed that the computed gradient for each model was very different depending on the temperature range used to compute these values.

Jan 1, 1994

By D. J. Chaiko

Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that we have studied are generated by combining an aqueous salt solution with an aqueous polymer solution. We have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. We have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS): In this chapter we review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation.

Jan 1, 1996

By Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa

"Thermodynamic properties of impurities in molten silicon are of prime importance in developing economical production methods of solar grade silicon. In the present research work, thermodynamic properties of boron, the most difficult element to remove from molten silicon, were measured by chemical equilibration techniques at 1723 and 1773 K. Activity coefficients and self-interaction parameters of boron in molten silicon were determined by equilibrating the melt with solid BN under controlled nitrogen partial pressures. Interaction parameters between boron and nitrogen in molten silicon were also determined by equilibrating the molten Si-B alloys with solid Si3N4• Based on the data obtained, the stability diagram of the Si-B-N system was established.IntroductionPhotovoltaic power generation using a silicon solar cell is expected to be the most promising energy source, because it is inexhaustible, cleaner and more safety than conventional energy sources, such as thermal or atomic power generation. At present, expensive off-grade silicon for semiconductor (SEG-Si) is used for a solar cell production. However, if a large-scale photovoltaic energy conversion using silicon solar cell comes into wide use in the near future, silicon will be sure to be in short supply for the cell. Therefore, a development of a new large scale process for solar grade silicon (SOG-Si) production is definitely necessary, which can remove contained impurities from silicon.Among the impurities contained in silicon, boron is one of the most difficult ones to remove by a zone melting or an unidirectional solidification, because its segregation coefficient in silicon is close to unity (0.8). In addition, boron behaves as a p-type silicon semiconductor dopant and, therefore, its content in SOG-Si must be severely controlled. Although some attempts to remove boron by various metallurgical methods have been carried out [I -4], quantitative analysis has not been made due to lack in the information on the thermodynamic properties of boron in molten silicon. From this view point, the activity of boron in molten silicon was determined in the present study by chemical equilibration techniques at 1723 and 1773 K."

Jan 1, 1998

By Varadarajan Seshadri

A physical model based on similarity principles was constructed for simulating the RH degasser of CST (Companhia Siderurgica Tubarao, Vitoria, ES, Brazil) to evaluate the circulation rate of the metal which essentially defines the degree of exposure of the metal to vacuum in the chamber and thus of the refining rate, The circulation rate on the other hand will influence the decarburization rate and removal of dissolved gases like nitrogen and hence it is essential to optimise this parameter to get maximum refining efficiency with minimum refining times, thus improving the productivity of the secondary refining process. Mixing characteristics in the ladle is evaluated by pulse tracer addition using conductivity-meters located at the down leg as well as at several locations in the ladle. The influence of gas injection through nozzles in the upleg with simultaneous bottom injection of gas as well as nozzle blockage on the circulation rates were investigated. Also simulation experiments of kinetics of decarburization were carried out using CO2 adsorption-desorption process in sodium hydroxide solution as circulating fluid and the effect of, bottom gas flow rate in this case was also evaluated. The results were carried over to prototype and to optimize the process.

Jan 1, 2003

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The basics of microwave drying process of CuCl residue were studied by comparing the dielectric property of the residue with different moisture contents. The dielectric properties were measured by microwave cavity perturbation method. The dielectric constant and dielectric loss factor of the CuCl residue have a linear correlation with the moisture content. With this relationship, we can realize on-line measurement of moisture content of the CuCl residue by dielectric properties. The microwave drying experiments with different thicknesses (1-5cm) of CuCl residue were carried out, and the heating curve of the materials under different microwave powers (250-450W) was made. From these parameters, an optimized operation parameter of microwave roasting technology, the thickness of CuCl residue filter cake to be microwave roasted should be 2cm , was deduced.

Jan 1, 2015

By S. W. Marcuson

Smelting of nickel-copper sulfide ores at Vale Inco’s Sudbury operations commenced in 1888 and the first converting plant went into operation in 1892. As the demand for nickel grew, the smelting operations expanded and by the 1960’s the Copper Cliff Smelter featured the longest converter aisle in the world with space for nineteen Peirce-Smith converters. During this long period, different converting techniques and vessels were employed. The evolution of converting is reviewed with special emphasis on the modifications made to the Peirce-Smith vessel to accommodate the metallurgical and process needs of the changing times.

Jan 1, 2009

By Ahmad-Bitar¸ Riyad N., Shadia J. Ikhmayies

"CdSi-xTex thin films with O<x<0.3 were prepared on glass substrates by the annealing of CdS:In thin films produced by the spray pyrolysis technique. The annealing was performed in nitrogen atmosphere at 400 --,C in the presence of Te vapor. The compositions of the films were determined by energy dispersive X-ray detection (EDAX) measurements. Scanning electron microscopy (SEM) was used to investigate the morphology of the films. The transmittance of the films was measured at room temperature in the wavelength range 400-1100 nm and used to produce the absorbance of the films. The first derivative of the absorbance was used to estimate the optical bandgap energy Eg by using the minima in the first derivative. The relation between the bandgap energy and the fraction x was found to fit with a parabola and bandgaps in the range 2.196: =Eg: =2.480 e V were obtained. Urbach tailing in the bandgap was also investigated.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The fabrication process of these cells involves the deposition of a p-type CdTe absorber layer on top of an n-type CdS one which acts as a window. The efficiency of the solar cell is affected by the method of preparation of both layers [1, 2].Interdiffusion processes taking place at the CdS/CdTe interface have largely been realized to significantly affect the device performance [3] by changing the bandgap of both CdTe and CdS which modifies the spectral response of the solar cell [ 4]. The formation of a mixed crystal or a graded layer causes a reduction in the lattice mismatch at the CdS/CdTe junction [5] which is about 9% [ 6] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [7, 8]. A complete understanding of the properties of the intermixed layers CdSxTe1-x that usually constitutes the interfacial region in the CdS/CdTe solar cell is essential. According to our knowledge, a lot of research was devoted to the investigation of the diffusion of S into CdTe [3-5, 9]; but little on the direct investigation of the diffusion of Te into CdS [6]."

Jan 1, 2011

By Gabriel Bartholazzi Lugão de Carvalho, Sergio Neves Monteiro, Fabio Da Costa Garcia Filho

The thermochemical treatment of Pulsed Plasma Nitriding is employed as an alternative to improve the surface properties of metals, such as: increase surface hardness, improve wear resistance, extend fatigue life and also create a barrier to the diffusion of hydrogen into the steel to reduce the susceptibility to hydrogen embrittlement. In this study, the effect of such treatment on ASTM A36 steel is analyzed through two different nitriding conditions: 5 h and 660 Pa for the first condition and 15 h and 720 Pa for the second one. In both cases, the temperature was held at 300 °C. Thus, in order to verify the results, Vickers hardness analysis and metallographic observation were carried out under an optical microscope. Only the second condition was able to achieve what was proposed, the formation of a uniform nitriding layer and an expressive increase of hardening on the surface.

Mar 1, 2018

By William Petruk, J. H. Gilles Laflamme, Jean Robitaille, Louis J. Cabri

"A quantitative mineralogical study using ore microscopy, electron microscopy, proton-microprobe, image analysis, and material balances was done on samples from the circuit of a concentrator in Quebec, with particular emphasis on the Cu concentrate. The ore contains many different minerals, of which the principal ones, in decreasing order of abundance, are pyrite, sphalerite, chalcopyrite, bornite, galena, tennantite, and pyrrhotite. Minor to trace amounts of covellite, chalcocite, stannoidite, mawsonite, colusite, wittichenite, miharaite, hessite, petzite, electrum, and an unidentified Cu-Pb-Bi-sulfide also occur.Liberation of pyrite is very high in all size fractions for all samples (ranging from 80-91 %). Liberation of chalcopyrite, bomite, sphalerite, and tennantite is relatively high, on average, in the head .sample and Cu concentrate (55-78% and 66-88%, respectively). Most of the chalcopyrite in the flotation tails is not liberated, whereas about one half of the tennantite and sphalerite are liberated in both the flotation and :final tails. Recoveries calculated for the Cu concentrate (on the basis of assays, mineralogy, and image analysis) are chalcopyrite 72. 5%, bornite 73. 7%, sphalerite 41.0%, tennantite 70.9 %, and galena (together with some trace minerals) 34.2%. It was also calculated that the Cu concentrate contains 10.0 % of the pyrrhotite and i.4 % of the pyrite.Materials balance calculations were done on the five major sulfide minerals to determine the mineralogical distribution of 13 major, minor, and trace elements (as determined by protonmicroprobe analyses). It was determined that tennantite is the principal carrier of Bi (67%), As (90%), and Te (86%) in the Cu concentrate. Therefore, removal oftennantite, which is mostly liberated in the Cu concentrate would significantly reduce these three contaminant elements, but at a loss of9% of the Cu, 2.0% of the Zn, and 0.7% of the Ag. The precious metals (Au, Ag) occur as discrete minerals (electrum, petzite, hessite). Some of the Ag also occurs in solid solution in bornite (23.1% of Ag in Cu concentrate), tennantite, and sphalerite. Four of the major sulfides (chalcopyrite, bomite, sphalerite, tennantite) in the ore also contain measurable concentrations of the following trace elements: Se, Cd, In, Sn, and Sb, occurring mostly as solid solutions. Some of these elements are also concentrated (up to about 18%) in minor and trace minerals such as colusite, stannoidite, and mawsonite."

Jan 1, 1999

By Shunsuke Yagi

A surface alloying technique was investigated using alternating pulsed electrolysis in an aqueous solution containing a single metal component for the formation of an Fe-Cr layer on an iron substrate. In the process, the iron substrate was dissolved during each anodic polarization of the pulsed electrolysis, providing iron ions in the vicinity of the substrate, while the Fe-Cr alloy was electrodeposited during subsequent cathodic polarizations. A bright, flat, and crack-free Fe-Cr layer with a composition gradient was obtained using a solution containing a trivalent chromium component and a complex forming agent together with some supporting or buffering salts.

Jan 1, 2006

By Marcio B. Fonseca

Nickel-cobalt laterite deposits have become the focus of attention for hydrometallurgical processing. Following the lessons of the second generation high pressure acid leach (HPAL) projects in Western Australia other Ni-Co laterite projects are now evaluating potential HPAL projects with a rigorous integrated approach that begins with geological modeling, resource estimation and metallurgical studies. The Vermelho nickel-cobalt laterite deposit has been under exploration and study for several years with investigations of various metallurgical processes. Recent HPAL studies have indicated that the nickel and cobalt laterite at this deposit is amenable to upgrading by silica rejection followed by pressure leaching. These studies have required a detailed geological investigation to generate a new resource model. The recent development of a sophisticated geological model integrated with a multi-element resource estimation for this complex tropical nickel laterite deposit in northern Brazil provides an example of the contribution of geology at the critical project stage where process technology decisions are made on relatively small samples of the total resource.\ Keywords: Ni Laterite, Geological Modeling, Resource Estimation

Jan 1, 2004

By André L. B. Bittencourt

The copper content in the waste slag represents the greatest loss in the process of Caraíba Metais&apos; Smelter. By identifying the variables responsible for copper stabilization in the slag, a minimization on these losses is expected, producing a granulated waste slag with a copper content lower than 0.7%. Statistics resourses such as control charts, Pareto&apos;s diagram and correlations curves were applied for the data obtained in the first semester of 1992. The magnetite and the calcium oxide contents in the slag of the Flash Smelter Furnace were most prominent variables. Some operational changes introduced during and after this investigation have shown good results.

Jan 1, 1994

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2Si/MgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (P/M) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2JIm is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ forming process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm) and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young&apos;s modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Sedef Pinar Basag, Onuralp Yucel, Ahmet Turan

Niederschlag process is commonly used to produce metallic antimony. The process is a metallothermic process which is conducted in one step for metallic antimony production. Using this method Sb2S3 is mixed with coal and metallic iron and subjected to reduction. During heating, antimony sulfide is decomposed and sulphur combines with iron to form the matte phase. Metallic antimony is collected at the bottom of the crucible. In this study, evaluation of Sb2S3 concentrate, extracted and obtained from West Anatolian Region of Turkey was investigated by using Niederschlag process. The reductant stoichiometry, reduction temperature and duration were carried out in the experiments. Chemical analysis methods by using atomic absorption spectrometry (AAS) and X-ray diffraction spectrometry (XRD) techniques were used for the characterization of the concentrate, metallic nuggets and matte phases.

Jan 1, 2016

By Jintao Gao, Zhancheng Guo, Chong Li

A new approach to enrich MFe and RO phase from the converter slag by super gravity was investigated. The samples obtained by the gravity coefficient G=600 and cooling rate V=5K/min from 1623K to 1373K appeared significant stratification and the MFe gathered at the bottom of sample. With the help of metallographic microscopy and X-ray diffraction, it is found that large quantity of white RO phase gathered at the lower part of the sample as the concentrate, with volume fraction appearing gradient distribution along the direction of super gravity, while the upper part was mainly composed of dicalcium silicate as the tailing. The mass fractions of the FeO, MgO and MnO in the concentrate are up to 40.46%, 6.9% and 3.91%, while that in the tailing are just 11.65%, 2.15% and 1.55%. The recovery ratios of FeO, MgO and MnO in the concentrate are 60.35%, 58.45% and 72.24%, respectively.

Jan 1, 2016

By Peter G. Cooper

"During 1987, the feasibility of modernising the ER&S smelter at Port Kembla, NSW, Australia was studied. The selection of appropriate technologies to carry the smelter into the 21st century considered issues such as capital cost, existing infrastructure, feed mix, capacity, product quality, flexibility and potential for further development. Both hydrometallurgical and pyrometallurgical process schemes were considered. Some novel combinations were assessed but ultimately rejected. Final technology selections included proven smelting and anode furnace processes, pyrometallurgical slag cleaning and modifications to existing equipment. This process scheme balanced risk against development potential within the constraints imposed by the existing plant.BackgroundThe Electrolytic Refining and Smelting Company of Australia (ER&S) has operated a custom copper smelter at Port Kembla since 1908. Existing technology includes a sinter plant/blast furnace, three small Peirce Smith converters, two reverberatory anode furnaces and a conventional tankhouse. These process units were all installed prior to 1960 and have proven to be flexible enough to process the wide variety of domestic feed materials purchased by ER&S.However, by the early 1980s, threats to domestic concentrate supplies highlighted the need for major changes to reduce operating costs to world competitive levels. Various studies in the ensuing years failed to identify an economically attractive solution. Furthermore, pressures were increasing to improve the environmental performance of the smelter.During 1986 the options for redevelopment were again considered and by the end of 1987 technologies for the retrofit had been selected and a full feasibility study was completed."

Jan 1, 1988

By Lawrence D. May, Harry Mudgett

"In the course of developing a new industrial process, information produced at the Research and Development (R&D) stage is critical to determining the technical and economic feasibility of the project. Understanding the fundamental operating parameters for each unit operation in a flowsheet typically comes from historical knowledge of similar systems or by technical development through a robust research program. This approach holds true for processes incorporating fluidized-bed technology. In this paper, the authors will present a practical approach for performing a research study that will allow a process owner to determine if the concept of using a fluidized-bed system can become a reality. Included are discussions of key steps required at each level of the R&D program, and the critical information required for advancing the project to the next stage.IntroductionThe conduct of a research and development program typically starts with a process owner identifying a new industrial need or modification to an existing operation. The owner can pursue this need through multiple routes, including initial in-house development, coordination through an engineering firm, contacting suppliers of key equipment envisioned for the process, or through direct contact with research and development organizations. Where and when the project is conducted is as variable as the number and types of owners who pursue them. Factors that can influence the decision of where to conduct a research program can include the type of process desired, the scale and scope of the project, the location of the project site relative to the R&D options, the experience, capability, and availability of the potential research sources, and the costs to conduct the program. Often, the owner may choose a combination of the available resources to achieve their objectives. In the end, the owner's choice should be based on a thorough understanding of their goals and objectives for the program, and a good understanding of how to measure success while achieving those objectives. Herein, the authors will describe the methods we have typically used to develop the information an owner needs to make an educated decision for investing in a new or modified process."

Jan 1, 2014

By A. R. Udupa

The reduction roasting behavior of chalcopyrite has been investigated using various combinations of a desulfurizing agent, i.e., CaO or Na2CO3, and a reductant, i.e., CO, H2 or C. Using these, combinations the sulfur is removed from the mineral as CaS or Na2S rather than SO2 as is the case with conventional copper smelting and converting. The laboratory reduction ex¬periments were conducted using thermogravimetric analysis (TGA) and boat tests of mixed combinations of fine particulate reactants subjected to a continuous gas stream. The degrees of metallization were determined by both weight loss and chemical analysis methods and the products examined using optical and scanning electron microscopy and electron probe microanalysis. The percent reduction after one hour at 900°C ranged from 60% to 94%. From these data It was possible to provide postulations as to the controlling reduction mechanisms.

Jan 1, 1983

By Theo Lehner

The Rönnskär smelter has wide experience in the field of recycling of non-ferrous metals. Today, smelting and refining from primary and secondary raw materials are integrated in a complex flow sheet. Boliden operates a lead flash smelter, a lead refinery, a copper smelter and refinery, a sulphuric acid and sulphur dioxide plant, a slag fuming plant and precious metal plant at its Rönnskär smelter in the North of Sweden. The Business Area Smelter Operations also incorporates Boliden Bergsöe, Sweden&apos;s lead-acid battery recycler, and Norzink, Norway, where recycled zinc accounts for more than 20% of it&apos;s production. Raw materials for the Rönnskär smelter include concentrates, ashes, slags, metallic scrap, electronic scrap and electric arc furnace (EAF) steel-making dust. This paper briefly describes current operations and illustrates current measures to improve productivity. Limits to recycling as experienced by a non-ferrous smelter are, illustrated. The deportment of critical elements contained in raw materials is also discussed.

Jan 1, 1998