Search Documents

By N. Gopalakrishnana, R. Beccard, S. Lourdudoss, R. Holz, M. Deschler

"Rapid growth of conducting and/or insulating InP, GaAs, Gao.47In0.53As, and GaAs0.6Po.4 on one or more of (001), (110), (111)A, (3ll)A and (3ll)B surfaces by Hydride Vapour Phase Epitaxy (HYPE) is demonstrated. The maximum growth rate of the binaries lies between 12 and 300 µm/hr and of the ternaries between 7 and 170 µm/hr. A simple model is developed to describe the influence of crystallographic orientation on temperature dependent growth rates. The growth rates predicted by the model is compared with the experimental values. Room temperature resistivity of insulating InP:Fe can be as high as 5xl09 ohm cm. Temperature dependent differential resistivity is also analysed. This feasibility of growing conducting and insulating layers rapidly on different orientations is very useful for electronic and optoelectronic devices.IntroductionRecently there is a renewed demand for very thick layers of III-V compound semiconductors for high performance electronic and optoelectronic devices [1]-[2]. Long wavelength high speed lasers that can be modulated up to 30 GHz necessitate epitaxial growth of semi-insulating (SI) layers [3]. There is also an increased interest on the growth of epitaxial layers on surfaces other than (001) surface. Epitaxial growth of these materials on such surfaces is of theoretical importance besides being technologically relevant. These demands led us to focus on the growth of conducting and insulating III-V compounds by Hydride Vapour Phase Epitaxy (HYPE). lnP, GaAs, Gao.471no.s3As on lnP and GaAso.6Po.4 on GaAs were grown as conducting materials using Low Pressure HYPE (LP-HYPE) on (001) 2° off substrates. Gao511no.49P on (001) GaAs substrate and lnP on lnP substrates of (001), (110), (l 11)A, (31l)A and (3 ll)B orientations were grown as semi-insulating materials using Atmospheric Pressure HYPE (AP-HYPE). In this report we present the growth aspects of these materials. We also present a simple model on the growth of InP on substrates of various orientations. The theoretically obtained temperature dependent growth rates are compared with the experimental values. Differential resistivities of semi-insulating lnP grown on substrates of various orientations as a function of temperature are also summarised."

Jan 1, 1998

By Chao Du, Xiaohui Ning, Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao

"TiCxOl-x solid solutions were synthesized by sintering a mixture of titanium carbide and titanium monoxide at 1600 °C. The corresponding structures and morphologies of the TiCxOl-x solid solutions were characterized by XRD and SEM. A series of tests has been performed on the electrochemical dissolution behavior of TiCxOl-x solid solutions in NaCl-KCl molten salt. The influences of synthesis time and electrokinetic parameters on the anodic dissolution behavior were also investigated. The results showed that TiCxOl-x solid solutions can dissolve as Tin+ into alkali chloride melt. Titanium ion species dissolved from TiCxOl-x solid solutions changes between Ti2+ and Ti3+ depending on the applied potential. The tail gas on the anode was monitored by a mass spectrometer. It was found the synthesis time significantly affects the components of the anodic gas.IntroductionTitanium and titanium alloys have been desired greatly because of their many uses. The critical factor that restricts the range of uses for Ti is its high cost of extraction. The primary titanium metal, sponge titanium, is still produced industrially worldwide by a process invented by Dr. Kroll in the 1940s[1] •Since the early 1970s, the research focus of the titanium industry has been directed towards developing a continuous process to produce high purity titanium at low cost. [2-10] Of the many alternative methods that have previously been investigated, the electrolytic process has been considered a promising method for titanium metallurgy [4-10]. Recently, several electrolysis and related methods such as the PFC-Cambridge process[11-15], calciothermic reduction[16-18], USTB [19,20] and MER[21] process were extensively investigated.The USTB process is a new approach where the pure titanium can be directly obtained by the electrolysis with an anode of titanium oxycarbide in molten salts[19, 20]. The titanium oxycarbide was produced by carbothermal reduction of titanium dioxide under vacuum at a temperature"

Jan 1, 2011

By C. Isaac Garcia, Sihai Jiao, Anthony J. DeArdo

"A practical model based on the Hill analysis has been developed to calculate the Lankford value of interstitial free (IF) steels and its distribution in different rolling directions, by considering only a few selected texture components. The Texture Intensity Ratio (TIR), i.e. (111 ) /(100), was used in the model to describe texture. By using the new TIR parameter, the texture-based prediction models can be used more easily to predict the Lankford value in a rather straightforward way.IntroductionThe deep drawing capacity of sheet steels is generally indicated by the Lankford value, which is mainly determined by the texture in steels1. Traditionally, various models derived from the Taylor model are employed to calculate the Lankford value from the texture2-4. In such models, the plastic deformation of steel is assumed to be the result of the slip of dislocations in certain slip systems, i.e., by either pencil glide or restraint glide. The slip direction is the <111> direction. In the case of pencil glide, the slip is thought to be possible in all crystal planes with the <111> crystal direction. Assuming the material is elongated in the X1-direction by d n and compressed in the X2 and x3-direction by qd n and (l-q)d n, respectively, corresponding to a deformation tensor"

Jan 1, 2001

By Du Sichen, S. Seetharaman, Wei Liu

"The viscosities of two-phase mixtures are of great importance in the modelling of the fluid flow in metallurgical processes. For example, in steel making and refining, the intimate mixing of metal droplets in the slag phase requires a consideration of the effective viscosities for the mixture. The present work was aimed at an understanding the phenomena underlying the viscous flow in a two-phase mixture with widely differing viscosities.Emulsions of silicone oils of known viscosities (345mPa.S and 1010mPa.S at 293K) with small amounts of water evenly distributed in the same were prepared by subjecting the mixture to uniform stirring using a magnetic stirrer. The viscosities of these emulsions were measured at constant temperature by rotating cylinder method using Brookfield Digital Rheometer. The uniformity of the preparation of the emulsions was confirmed by the reproducibility of the results. Th7 measured viscosities were generally found to be independent of the torque under the experimental conditions so that the two-phase mixture could be considered as a Newtonian liquid. The variation of viscosities with temperature and the effect of addition of a surface-active substance were also studied in this work.The measured viscosities were found to be· higher than those of both pure water and silicone oil. The experimental viscosities were found to increase with increasing concentration of water. The influence of surface tension on the viscosities was examined by adding surfaceactive agent to the mixtures. The result is discussed and compared with theoretical models developed by Einstein, Taylor and Oldroyd."

Jan 1, 2000

By Fuqiang Zheng, Yufeng Guo, Pengfei Li, Guanzhou Qiu, Tao Jiang, Andrew Yakovlevich Travyanov

Low content of TiO2 and high impurities content of Ca and Mg are the shortcomings of domestic ilmenite. To meet the requirements of the material in the titania produced by chlorination process and titanium sponge industry, enrichment of ilmenite is necessary. In the process of enriching ilmenite, high temperature and reductive condition were beneficial to the formation of anosovite, but the high content of magnesium oxide which was solid soluble in anosovite baffled the following separation. So the effects of pre-oxidation and reductive conditions including reduction temperature, reduction time and hydrogen concentration on the phase composition and metallization rate were studied. The characteristics of reduction samples were analyzed by X-ray diffraction and optical microscope. Results have shown that the reduction product is mainly composed of Fe, Fe(Mg)TiO3 and TiO2 at 1123K, its metallization rate is about 65%,magnesium exists in Fe(Mg)TiO3.

Jan 1, 2015

By Takuya Shinagawa

After vitrification of the residues from a municipal solid waste incinerator, the vitrified products can be used as a construction material, and the dust can be used as raw materials for the non- ferrous industry. The NKK electric-resistance furnace is operated under a reducing atmosphere, and heavy metals such as zinc and lead in the ash vaporize to form dust. Also, dust from the NKK electric-resistance ash melting furnace is composed of water insoluble zinc and lead components and water soluble NaCl and KCI. This is why, The concentration of zinc and lead in the dust after washing is sufficiently high for the dust to be used as a raw material for the zinc and lead industry. NKK developed a heavy metal recovery process in which zinc and lead in the dust are reclaimed as a raw material for smelting by making the best use of the characteristics of the dust.

Jan 1, 2002

By Tam Tran

Over the last decade, halide (chloride, bromide and iodide) systems have been evaluated as alternative lixiviants for the processing of gold to replace cyanidation which has been widely used in commercial practice. This paper first reviews the development of processes promoted by Kaljas Ltd / Lachlan Resources (Australia) and Great Lakes Corp (USA) using different bromide/bromine systems in the early 1990&apos;s. Several research groups subsequently evaluated the use of iodide/iodine and chloride/chlorine for gold extraction, showing similar characteristics of gold/silver dissolution and recovery. A critique is :given on the advantages and the ,shortfalls of halide systems as alternative lixiviants. The stability of gold? halide complexes is discussed, based on practical experience and thermodynamic modelling of their speciation, The iodide system provides the most stable gold / silver complex for easier handling. However, the cost of iodide inhibits its application for are processing. In this critique, emphasis is given on the cheapest system, which involves the use of chloride for leaching (in conjunction with an appropriate oxidant). However the chloride-base leachant has a major drawback which is related to the unstable nature of gold chloride in a reducing environment.

Jan 1, 1998

By C. D. Mishra

The recycling potential for any gainful utilisation of the waste products is dictated by their quality, especially the chemical characterisation. The methods commonly used for the analysis of fly ash e.g. wet chemical, AAS, ICP-AES etc are time consuming. The paper describes a rapid XRF-based method for routine analysis of fly ash which involves preparation of local standards, optimisation of sample preparation technique and use of a simple PC-based software to account for interelement effects. The matrix corrected values are found to agree well with the wet chemical data.

Jan 1, 1992

By Osamu Iida

Since &apos;start-up of the larger Mitsubishi Continuous Copper Smelting Process in 1991, furnace relining campaign was gradually prolonged to once every 2 years according to deregulation of governmental boiler inspection. On the other hand, in 1998 Naoshima smelter embarked on an intermediate strategic expansion plan to strengthell its international competitiveness. As part of this plan, modifications were implemented in the copper smelter designed to increase output of anodes from new charge source to 270,000 tpa. In May 1998, treatment of dried neutralized residue was started in C furnace, and during the shutdown for brick relining in April 1999, intensive modifications to the boilers as well as the installation of new spray coolers for furnace off gas treatment were implemented. Finally, the new larger oxygen plant was commenced its operation in May 2000 and the expansion was achieved around 30% increase of anode production from original design.

Jan 1, 2001

By Deepak Gupta, R. Kageyamat, J. W. Evans

"In electromagnetic casting, a liquid metal pool is partly supported by electromagnetic forces resulting from the interaction between induced currents and an alternating magnetic field. Stability of the metal surface is of paramount importance if the cast ingot is to be free from surface defects. Prior work by Garnier and Moreau had suggested that the magnetic field has no influence on the surface stability, but a more complete analysis at Berkeley suggested that surface perturbations are destabilized by the magnetic field once a critical magnetic field is exceeded. More recently we have employed a modified version of the software SOLA to compute the behaviour of a melt surface in the presence of an alternating field. The computed results support the theoretical analysis in predicting an unstable surface. Experimental work is now in progress to examine the stability of a mercury pool in the presence of an alternating field. Introduction and Previous InvestigationsElectromagnetic casting (EMC) is a technique widely employed in the aluminum industry to produce ingot for subsequent rolling. It is a ""continuous"" casting technique (illustrated in Fig. 1) producing ingots several meters high (and perhaps 1m by 2m in horizontal dimensions) at a casting speed of one or two mm. per second. The technology has gained acceptance because the metal is solidified without contact with a mold. Consequently the surface finish of the ingot is usually smooth and the ingot can be fed directly to rolling without machining, the surface (""scalping""). Scalping is necessary with alternative technologies (e.g., DC casting) where a mold is used. Consequently any disturbances that result in surface imperfections of EMC ingot are a serious matter. One type of imperfection is waviness on the surface of the ingot; a line drawn along the crest of a wave would run horizontally around the ingot. This imperfection may be caused by waves on the surface of the metal pool. As the waves reach the solidification line at the periphery of the metal they cause alternate outward and inward bowing of the meniscus at that point with attendant small (but significant) changes in ingot width. Elimination of building vibrations and similar disturbances minimize the occurrence of these surface waves but it is interesting to speculate whether there are disturbances of the metal pool that arise from the electromagnetic forces supporting the liquid metal. These forces are generated by the interaction of currents induced in the melt and the magnetic field produced by the current imposed on the inductor surrounding the melt. The present investigation has been concerned with whether the alternating magnetic field destabilizes the melt surface."

Jan 1, 1994

By I. A. H. Schneiderl

Eichhornia crassipes approaches being a scourge in many parts of the world, .choking waterways and hindering transport upon them. At the same time it is known to readily abstract heavy metal ions from water and, thus, aids in the removal of heavy metals found in such waters. This paper considers the possibility of using specific parts of the plant as an inexpensive adsorbent for the removal of heavy metals from contaminated chemical and mining industry waste waters. In particular the root of the plant was found to be an excellent accumulator of &apos;heavy metal ions including uranium from solution. It is. also suggested that dried roots of the plant ?might be placed in simple bags and used in a very low cost metal ion removal system.

Jan 1, 1995

By Susumu Imashuku

A pseudoternary phase diagram of the BaO?ZrO2?ScO1.5 system is established and the conductivities of the scandium-doped barium zirconate are measured in wet conditions. According to the phase diagram, the molar fraction of scandia in the barium zirconate phase that equilibrates with the cubic zirconia (ZrO2) and scandia (Sc2O3) phase is 0.03. On the composition line, where the molar fraction of barium oxide (BaO) is 0.50, the solubility of scandia into barium zirconate is 0.27 as a molar fraction of scandia. At around 500 °C, the conductivities of scandium-doped barium zirconate are estimated to be almost same as that of yttrium-doped barium zirconateThe activation energies for bulk proton conduction in scandium-doped barium zirconate (0.57 eV for BaZr0.90Sc0.10O3-d) are higher than that of yttrium-doped barium zirconate (0.44 eV for BaZr0.90Y0.10O3-d). In addition, the bulk conductivity of scandium-doped barium zirconate in this study is 10 times higher than the reported conductivities in the temperature range of 75 °C to 300 °C.

Jan 1, 2006

By Guo Xian Jian

In this paper, the effects of matte grade, flux grain size, blast flowrate and blast O2 content on the process of silica flux melting in a copper converter were investigated. The results showed that the blast flowrate and the blast 02 content were not significant factors in the melting process. However, with an increase in grain size of flux and grade of matte, the amount of the flux molten decreased. The data on the melt rate of process correspond well with the mathematical model which simulates the chemical reactions occurring at the interface. The kinetic equations of melting are as follow:

Jan 1, 1996

By P. T. Velu, R. G. Reddy

"The use of emf measurements to derive classical thermochemical data has been in use for many years. The reaction associated with electrochemical process is harnessed in a galvanic cell and energy involved measured in terms of electromotive force. The property requirements of sensor electrodes used differ for various aqueous, molten salt and solid electrolyte systems. The electrodes for molten salt electrolytes need special care for construction. This paper describes the studies carried out using an Ag/ AgCI reference electrode. This electrode was used to measure the solubility of compounds in molten salt electrolytes. The results obtained using this electrode are in excellent agreement with the values from chemical analysis method.I. IntroductionThe technique of obtaining a metal from its oxides by electrolysis is more than a century old process now. In these processes, it has been well established that for halide electrolytes, only the dissolved oxides are available for the dissociation at the electrode to release the metal during electrolysis. Therefore, the solubility of metallic oxides in the molten salt electrolytes is an important parameter which determines the economical and technical viability of these processes. The widely used molten salts systems in halides are fluorides and chlorides. The fluoride electrolyte system is used in our present study.The viability of obtaining aluminum alloys by in-situ electrochemical processing has been outlined in our earlier publications[1-8]. Studies on the solubility of various alloying element compounds is a part of our ongoing research efforts for the direct production of Al-Li alloys. As mentioned above, the solubility of lithium oxide and lithium carbonate compounds in molten fluoride electrolyte system have studied using EMF technique. The change in potential of the molten electrolyte was measured by a working electrode against the reference electrode with the addition of lithium compound."

Jan 1, 1997

By Wang Chen

COREX process is briefly introduced. A static model combining a set of mass and heat balance equations has been developed. Taking the specified inputs from the graphical user interfaces, the model is capable of calculating the consumption of raw materials and fluxes, the volume and composition of the slag and the volume and composition of the generator gas. The model enables the examination of the changes of materials and energy flows induced by the variations of operational parameters and raw materials chemical analysis. The model allows a detailed process analysis and adjustment of the plant operation and can thus be used to improve plant operation.

Jan 1, 2008

By Mingming Zhang

This paper describes the aluminum electrowinning in a batch recirculation cell system using 1-hexyl-3-methylimidazolium chloride and aluminum chloride (ionic liquids) as electrolyte at low temperatures. The technique proposed to deposit aluminum from ionic liquid electrolyte was a three-component electrolytic cell system. Ionic liquid electrolyte was circulated between electrolytic cell and electrolyte reservoir by ceramic piston pump. Two different anodes were used in the electrowinning and it was found the extruded carbon anode had better electrochemical stability and reusability. The cell performance variables studied were the current density and current efficiency as a function of aluminum ion concentration, electrolyte flow rate and applied cell voltage during batch recirculation operation. Results indicated that the current density was directly proportional to the applied cell voltage, initial electrolyte concentration and electrolyte flow rate. Under batch recirculation operation at applied voltage of 3.5 V and temperature of 80-90°C, 80-90% current efficiency of cathodic aluminum deposition can be achieved when flow rate is 20mL/min and initial concentration is 10 mol/L.

Jan 1, 2006

By W. J. Guay

Scrubbing of simulated copper reverberatory furnace gases containing 1.0 percent sulfur dioxide with the minus 74 ~m fraction of the San Manuel tailings has shown sulfur dioxide removals of almost 100 percent over an effluent pH range of 3.1 to 4.6 and a wide range of liquid to gas ratios with absorptions of 11 to 17 Kg of sulfur dioxide per tonne of minus 74 um slimes. The high reactivity of the tailings slimes with S02 indicates that the reaction rate is not controlled by the slow dissolution of calcium carbonate in sulfurous acid which characterizes scrubbers using ground limestone. The interpretation of these results has been considerably enhanced by wet chemical analysis and emission spectrographic analysis which show that calcium and iron account for about 90 percent of the SO2 absorption with the rest being accounted for by aluminum, magnesium, potassium, and sodium. Mineralogic examination confirms the, chemical and spectrographic analyses showing that the major constituent removed from the slimes is calcium carbonate, with lesser amounts of chlorite and montmorillonite (silicates containing iron, magnesium, aluminum, and calcium) being removed.

Jan 1, 1981

By Makoto Suzuki

After hot rolling, stainless steel strip is processed by the Hot Rolled Annealing and Pickling line (HAP) , where H2SO4 or mixed acid of HNO3 and HF is normally used. In the pickling bath, metal oxide accumulates in the form of sludge, which should be removed from the bath regularly. A new automatic continuous sludge disposal system has been introduced at Chiba Works of Kawasaki Steel Corporation to increase sludge removal efficiency and improve the working environment. The elements of the equipment are as follows. a. Ejectors in pickling bath: to carry the mixed acid into the circulation tank through the piping system. b. Sedimentation bath : to sediment sludge out of the bath. c. Skip conveyer : to convey a specified volume of sludge into a kneading for device for neutralizing. The sludge removal efficiency of this system is very high. and the volume of sludge accumulation in the pickling bath has substantially decreased.

Jan 1, 1996

By S. Suzuki, Y. Maeda, N. Wakamatsu

"A new pyrometallugical technology, named KLS process, has been developed by Dowa Mining at its Kosaka Smelter to smelt various kinds of lead raw materials.The process consists of clearly separated two reaction steps, smelting and reduction. For this purpose, respective stationary furnaces are installed which are connected by a slag launder.Dry raw materials, together with pulverized coal and oxygen-enriched air, are injected through a lance pipe into the molten slag in the first furnace. It is kept under a high oxygen potential to remove sulfur completely. Resultant PbO rich slag overflows to the second furnace where pulverized coal and insufficient air are also injected through a lance pipe to reduce PbO to lead bullion and to compensate for thermal deficit. The entire operation is carried out continuously. The process development started back in 1981. In late 1986, a pilot plant with a capacity of 3.5t/H was constructed.Already nearly 20,000 tons of raw materials, mostly lead sulfate mixtures have been smelted successfully.IntroductionFor a long time, main raw materials for lead smelting at Kosaka smelter have been such secondary incombustibles as lead sulfate and lead-barium sulfate. The former is leach residue of the copper smelter flue dust and the latter originates from Iijima zinc refinery. While the most of lead concentrates produced locally has been smelted by an ISF of Hachinohe smelter in which Dowa Mining has a share.The surplus lead concentrates were processed at Kosaka by a hydrometallurgical method to convert PbS to PbSO 4 as pretreatment, and followed by simultaneous smelting together with the above secondary materials (1). Approximate output has been 1,5000 /M of lead bullion and slightly more than 2,000t/M of refined lead by adding lead bullion returned back from Hachinohe smelter (2)."

Jan 1, 1988

By Kenneth L. Driggs

The Environmental Protection Agency&apos;s Clean Air Act of .1970 provided the driving force for the current Magma Smelter configuration. The historical and technical perspectives of those process developments are reviewed. Innovations in procedures and equipment have allowed compliance with the requirements of the regulating authorities. The wet scrubbing of converter gasses and the monitoring of converter operations by a controlling foreman are two of the major contributors to these successes. The Clean Air Act Amendments of 1990 have posed many new concerns for all U.S. industry, including the few (seven) primary copper smelters remaining. Future concerns include tightening the sulfur dioxide ambient standard from the current three-hour averaging period to one hour"

Jan 1, 1992