Search Documents

By I. M. Ritchie

Cyanide owes its great success as a lixivant for gold to the great strength of the Au-CN bond. A replacement for cyanide must similarly be a strong complexant for gold (I) or gold (III). The various alternatives are briefly considered and it is concluded that only thiosulfate has a reasonable chance of replacing cyanide as a relatively non-toxic lixivant at the present time. However, there are considerable technical problems to be overcome before thiosulfate can be considered to be a realistic alternative to cyanide. Firstly, the leaching of gold using aerated ammoniacal thiosulfate with copper as a catalyst is a complex process which needs to be understood and controlled carefully in order to achieve maximum recoveries with minimum reagent losses. Secondly, there needs to be an option similar to the CIP process for recovering and concentrating the dissolved gold thiosulfate complex from pulps produced in the processing of low grade gold ores. The prospects for overcoming these technical' challenges are evaluated and discussed.

Jan 1, 1998

By S. P. Ball

A major limitation to maximising the rate of gold extraction in commercial operations occurs as a consequence of the limited solubility of oxygen in cyanide liquors. The use of additions of solid inorganic peroxides as an in-situ supply of oxygen to the lixiviant has been studied, in particular in its application to heap leaching. Experimental studies showed-that the release of oxygen into solution from these peroxides is very sensitive to solution pH. Agitated leaching tests showed that, when either Ba, Ca or Sr peroxides were used as the-sole source of oxygen, both the rate and extent of gold extraccion was enhanced. Column leach tests were used to simulate heap leach conditions. These showed that significant increases in the rate of gold extraction could be achieved by additions of calcium peroxide, made to the ore, prior to it being loaded into the columns.

Jan 1, 1989

By XUEWEN WANG, Bowen Li, Mingyu Wang

A novel technology characterized by higher extraction of vanadium and recovery of valuable elements was developed to recover vanadium from stone coal. The brief flow of the novel technology mainly includes low temperature sulphation roasting, water leaching, recovering potassium, aluminum, copper and selenium, solvent extraction enrichment vanadium, precipitation of red vanadium, removal sodium from red vanadium and calcinations. The total recovery of vanadium reached 76.3%, which was higher than the current applied technology. The novel technology was environmentally-friendly and could extract vanadium from the stone coal, in which the content of V2O5 was less than 0.8%.

Jan 1, 2015

By Mark Kruzynski, Srinivas Garimella, James T. Wiswall

"A flue gas recirculation (FGR) system for a combustion fired aluminum melting furnace is experimentally investigated. The FGR system flows combustion air in a turbulent jet within the flue gas stream, and the turbulent jet flow is collected in a tube at a distance from the jet exit. Entrainment of the flue gases as well as heat transfer between the flue gases and the jet occurs over the length of the exposed jet. Heat transfer between the flue gases and the jet, and the amount of flue gas entrained into the jet (derived from temperature, flow rate and oxygen fraction measurements) were measured as a function of nozzle exit velocity and the distance between the nozzle exit and collection tube. In addition to flue gas entrainment, a fuel savings of up to 7%, due to heat transfer over the length of the jet, was projected from the measurements obtained.IntroductionFlue gas recirculation can be applied to aluminum melting furnaces to control combustion temperature. When coupled with a device to improve furnace efficiency by recovering heat from the furnace exhaust, flue gas recirculation provides a control technique that is integral to achieving the goals of reducing fuel consumption, increasing product yield, increasing the longevity of infrastructure, and reducing pollutant emissions. In particular, combustion temperature control can help reduce reactivity of the products of combustion with the molten metal surface and furnace refractory materials. Combustion temperature control can also help improve the life of heat exchangers used to recover energy lost to the environment in the flue gases, and reduce NOx formation in the combustion process. Flue gas recirculation can also dilute oxygen used in oxy-fuel combustion to reduce reactivity.Flue gas recirculation has been used since the 1970s to control flame temperatures in the automotive industry [1-3] and has successfully reduced NOx emissions. Many different flue gas recirculation approaches for high temperature melting such as melting aluminum and glass have been patented since the 1980s [4-12]. There has also been academic interest to determine the fundamental performance characteristics of flue gas recirculation in high temperature furnaces and in combustion [13-15]."

Jan 1, 2014

By H. Y. Sohn

"The nonferrous production industry has gone through a remarkable transformation in recent years in terms of developing and adopting new technologies. Technology innovations have largely been driven by the need for greatly improved environmental protection in addition to increased productivity. One of the most notable aspects of the new technologies is their ability to reduce the emission of sulfur and other pollutants to extremely low levels.The current industry trends towards more environmentally friendly technologies are bringing about additional benefits of developing more efficient, technically advanced, and continuous processes in closed reactor vessels. Key aspects of these modem trends include the use of increased oxygen enrichment in the process gas, better process control, reduced manpower requirements, and plant operations with more skilled personnel.Computer simulation and modeling of complex processes have become more reliable, realistic, and thus increasingly useful in metal production. Some of the notable examples are reviewed.Finally, the need and advantages for value-added production in the nonferrous industry are discussed.I. IntroductionMost recently commissioned technologies for nonferrous metals production have been developed largely in response to environmental concerns. One of the most remarkable improvements made by the nonferrous industry in the last decade has been the rapid increase in sulfur capture. Before the start of the last decade, 90% capture of sulfur was considered good. Since then, strict emission regulations have become the norm in advanced societies, although smelters in many parts of the world still operate with limited pollution control. Other emissions and discharges have also been substantially reduced, resulting in much improved working conditions and worker hygiene in addition to the overall environmental protection. The development of the more environmentally friendly technologies has accompanied other advantageous advances made in the nonferrous industry, i.e., the trend towards more gas-tight, continuous processes and larger plants. This has increased the competitive edge enjoyed by the industry in the industrial countries, offsetting the higher costs of labor and pollution abatement that they have to overcome in those countries. Experience has shown that clean technology often leads to a profitable business, because its adoption forces the concomitant advancement of related technologies in addition to the avoidance of penalties imposed by the public on pollution-prone industries. Needless to say, there are other driving forces for new technologies such as reduction of operating and capital costs, improved product quality, and energy considerations in terms of reduced consumption and utilization of readily available sources."

Jan 1, 2000

By Knut H. Bech, Stein Tore Johansen

"The collision efficiency for small particles relative to 2D spherical bubbles in a developed turbulent flow field were calculated applying an adopted version of the CPD program FLUENT. The turbulence field was related to bubble size and fluid properties. The results were compared with analytical theory. The turbulence intensity was found to be the most important single parameter for collision efficiency. Effects of boundary layer thickness and particle diameter were discussed. IntroductionRemoval of inclusion particles from melted aluminium can be facilitated by means of a rotor system that supplies kinetic energy and gas bubbles to the floating metal. At the surface the inclusions adhere to the surface dross or slagg which is removed at regular intervals by the operators. When applying computational fluid dynamics (CFD) to model such a system, one experiences difficulties with the large range of turbulent length-scales encountered, from the large geometrical scales of the rotor and container, through the bubble size and down to the particle diameter. A mathematical model for the complete system will be both complex and require an extreme spatial resolution. Another way of dealing with the problem is to model the micro-scale phenomena separately and apply the results to create a model for the macroscopic system. In a previous work [12] we addressed these problems and developed a procedure for calculating turbulence enhanced flotation to bubbles. It was found that turbulence may have a profound effect on the collision rate of particles to idealized bubbles. In this study we recognize that only a fraction of the total turbulent kinetic energy generated by the rotor's work on the liquid metal may contribute to enhanced flotation. By using a model spectrum for the turbulence, the fraction of turbulent energy in eddies smaller than the bubble diameter is calculated. A twodimensional CFD model was then constructed to calculate the collision efficiency between particles and bubbles of various sizes."

Jan 1, 1999

By V. I. Lakshmanan

Wastes when produced can be reused or recycled prior to disposal. Industries that cause environmental concerns during manufacturing include primary materials and primary metals. Pollution prevention mechanisms to achieve waste reduction require new separation, reclamation, control and process simulation technologies. Substituting recyclables for virgin resources will reduce energy use, water pollution, air pollution, water use and mining wastes. Shrinking landfill space will spur new technologies for waste treatment and recycling. These situations hence offer opportunities for innovative flowsheets with appropriate separation technologies. Development of innovative flowsheets to treat recyclables offer unique opportunities for process/product development, obtain green products and hence market advantage. The paper will illustrate with selected innovative flowsheets to treat recyclables.

Jan 1, 1996

By S. J. Buckler

Many chemical and metallurgical processes use submerged gas injection to increase contact area between gas and liquid phases in order to promote faster overall reaction or refining rates. The total interfacial area produced by gas injection through lances, nozzles or tuyeres is both an important design parameter for new vessels and a measurement for estimating the maximum processing capacity of existing equipment. Estimating total interfacial area from submerged injection into industrial pyrometallurgical vessels from existing knowledge is a problem with two aspects. The first difficulty is the difference in behaviour of cold (aqueous) and hot (molten metal) systems, implying that existing models and correlations of gas-liquid behaviour developed in low temperature systems are not necessarily appropriate for estimation of high temperature behaviour. The second difficulty is the issue of scale-up of correlations from laboratory to industrial sized vessels. The work presented in this paper is part of an ongoing experimental investigation, at the GK Williams CRC for Extractive Metallurgy, to quantify the total gas-liquid interfacial area available in pyrometallurgical vessels using chemical measurement methods. The effects of three operating variables, injected gas flow rate, nozzle diameter and nozzle submergence, on total interfacial area are quantified in a IOOL aqueous system - the first stage of a three stage process in examining the implications for scale-up of high temperature, medium-scale results are discussed. The results of work at high, injected gas flow rates (up to 500/min) show that the submerged Froude number is not sufficient for use as the sole variable in a predictive model of total interfacial area. Further work is being undertaken to identify other dimensionless variables that will better represent the gas-liquid characteristics in submerged injection that influence the formation of total interfacial area. The second and third stages of the experimental investigation involve measuring the total interfacial area in a large-scale (1000L) aqueous sodium sulphite and small-medium scale molten metal baths.

Jan 1, 2002

By N. Menad

Thermal treatments of five different types of non-ferrous metallurgical wastes, under controlled atmosphere, were carried out at temperatures lower than 800 °C. The aim of these treatments was to reduce the toxic elements content and to increase that of valuable metals in the residue. <Best results were obtained by their treatments in air or hydrogen or successively both of them. Simple treatments using air or hydrogen of three samples allowed the elimination of more than? 95 % of their toxic elements and&apos; almost doubled their valuable metals&apos; concentration. For the rest two samples, combined treatment was necessary for their efficient decontamination and the concentration of valuable metals, in the treatments residue, to a reasonable value. Most of the solids issued from these treatments can be recycled in .the current non-ferrous metallurgical processes.

Jan 1, 1995

By Chen-Ming Kuo, Esher Hsu

"Under the 4-in-1 recycling system, Taiwan producers and importers who using packaging containers have responsibility to pay the recycling fees for recycling the waste packaging containers they produced or imported; while the collectors/recycling plants who collect/sort/recover waste packaging containers receive subsidy for conducting recycling. A reasonable pricing for recycling charge and subsidy is a way for sustainability of the recycling. The objective of this study is to provide an amending mechanism for product charge and recycling subsidy in response to the social economic changes. This study employs a regression analysis and cost adjusting model to link the factors used for calculating product charge and recycling subsidy on recycling waste packaging containers with socio-economic indicators, raw material prices, wholesale prices, and secondary material prices. Study results provide estimated models to EPA in Taiwan for amending product charge and recycling subsidy in response to the social economic changes.IntroductionUnder ""4-in-1"" recycling system in Taiwan, waste packaging containers are officially announced to be recycled. The waste packaging containers announced to be recycled include iron cans, aluminum cans, glass bottles, plastic containers, paper containers, aluminum foiled paper packs. In order to compensate the recycling system, EPA charges associated manufacturers and importers for recycling fee and subsidies recyclers to create the economic incentive for raising recycling performance. Basically, the budget for subsidy recyclers is from the recycling charge. That means if we want to increase recycling efficiency by increasing subsidy to recyclers then the manufacturers and importers have to pay more for reaching financial balance of recycling foundation. The benefit of recyclers and fee payers are always conflicted. The recycling charge and subsidy is thus argued by fee payers and subsidy receivers all the time. A reasonable pricing for recycling charge and subsidy is the only way to keep the recycling system sustainable. Moreover, a suitable mechanism has to be changed along with the changing social economic condition. The recycling performances and effectiveness of this recycling system is also highly dependent on the pricing mechanism. This study intends to provide an amending mechanism for product charge and recycling subsidy in response to the social economic change. Related previous studies about recycling system in Taiwan with its performance include Hsu and Kuo (2002, 2005), Bor, Chien, and Hsu (2004) and Hsu (1999). Hsu and Kuo [1] estimated total production values of recycling and evaluated the performance of recycling performance based upon the estimated production values."

Jan 1, 2011

By M. M. Monte

A method for removing metallic mercury from contaminated tailing, using the flotation process, is described. In order to define some relevant parameters for the mercury flotation system, microflotation and electrophoretic mobility tests were carried out on (pure) metallic mercury in the presence of several surfactants. Based on the results obtained from fundamental studies a series of bench scale flotation experiments with mercury containing tailings from two wetland sites in Brasil were done. The results of microflotation tests with mercury showed that by using cetyl trimethyl ammonium bromide, an increase in mercury flotability is observed in the acid pH range, whereas in the presence of potassium oleate the highest mercury flotability was found in the alkaline pH region. The mercury flotability using potassium amyl xanthate was improved by the addition at sodium dithionate as an activator. The bench scale flotation tests with contaminated tailings from Poconé (brazilian wetland site) showed a recovery of 70% when sodium dithionate was used as activator and potassium amyl xanthate as collector. The resulting coefficient of separation is around 60%. However, the results of the flotation experiments with fine fractions from amalgamation tailings from Peixoto de Azevedo (brazilian wetland site) showed a low mercury recovery (32%).The results from this work suggest that since in the Poconé site tailings, the metallic mercury is not completely associated to the finer particles, the flotation process to recover the metallic mercury seems very promisor.

Jan 1, 1996

By J. E. Clemson

The Black Pine sediment-hosted, disseminated gold deposit is located in Cassia County, Idaho. Gold mineralization occurs in flat-lying zones 50 to 100 feet thick. Total geological ore reserves are 5.6 million tons grading 0.049 oz/t. Ore types include: non-carbonaceous, oxidized ore; carbonaceous, sulfide ore; and carbonaceous, partly oxidized ore. In the oxidized ores, native gold grains commonly occur in porous hematite pseudomorphs that have replaced disseminated framboidal and euhedral pyrite, and this gold should be readily leached by cyanide solutions. Approximately 4 % of the native gold observed in the oxidized ores is locked within gangue and may be refractory to cyanide solutions. Native gold has not been observed in the unoxidized samples, all of which are characterized by primary sulfides. It is suspected that the bulk of the gold mineralization in the sulfide ore occurs as submicroscopic particles within pyrite and will be refractory to cyanidation. It is believed that much or all of the gold observed in the oxidized samples was originally in pyrite but was released and re-precipitated during oxidation. The degree of oxidation of the pyrite and the presence/absence of preg-robbing carbonaceous material is used as a guide in delimiting zones of mineralization amenable to heap leaching.

Jan 1, 1988

By K. A. Brunk

Newmont&apos;s research, operations, history and experience with pre-treatment of preg-robbing carbonaceous ores are described, with emphasis on the chemistry, physics and kinetics of chlorine treatment. Present operations, control strategy and projected changes are also described, including a summary of the adsorption of chlorine into pulps and off-gas scrubbing. Conditions of chlorination have been optimized by the use of Eh-pH diagrams of the gold-chlorine-water system, and have resulted in significant increases in gold recoveries and decreases in chlorine consumptions.

Jan 1, 1987

By D. Neuschiltz, M. Witthaut, R. Cremer

"Metastable (Ti,Al)N coatings with fee structure have been shown to exhibit superior performance as compared to TiN under conditions of wear at elevated temperatures due to their better oxidation resistance and hardness. The oxidation resistance of these coatings increases significantly with increasing Al-content. However, the deposition of (Ti,Al)N films with Ti/ Al ratios below about 30/70 leads to a hexagonal structure which is not suitable for tribological coatings. Only little is known about the location of the cubic to hexagonal phase transition and hence about the optimum composition of (Ti,Al)N hard coatings.To determine the position of this transition, Tii-xAlxN films with different Ti/Al ratios were deposited on high speed steel at substrate temperatures between 100 and 700 °C by means of reactive MSIP. The composition of the films was determined by electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS), the crystallographic structure by thin film X-ray diffraction (XRD).It could be shown that in case of deposition temperatures of 300-700 °C a two-phase region exists in the metastable TiN-AlN phase diagram, which expands with increasing temperature, wheras at 100 °C substrate temperature no two-phase region was observed. But in opposition to the phase diagram known from literature, which is based on thermodynamic estimations, the detected two-phase region is narrow for typical PVD temperatures, thus allowing the deposition of cubic single-phase Al-rich (Ti,Al)N hardcoatings for tribological applications. Based on these results, a new Ti1-xAlxN film with x = 0.62 has been developed, which showed an increase of oxidation resistance by a factor of 4."

Jan 1, 1998

By N. Kanari

One of the criteria to define the market value of chromite concentrate is its chromium to iron ratio. Changing this ratio for a definite chromite mineral is impossible by physical processing. This study investigated the possibility of increasing this ratio through the carbochlorination and the oxychlorination of chromite concentrates. Experiments are carried out up to 1000 °C. The characteristics of samples and reaction products are determined by SEM, XRD and chemical analysis. The carbochlorination of a chromite concentrate at about 600 °C leads to the . selective partial elimination of iron allowing a higher Cr/Fe ratio of the treated concentrate. Selective extraction of iron could also be achieved at about 950 °C by oxychlorination. In this case, a part of chromium contained in the concentrate is recovered as chromium oxychloride. The obtained residue had high content of Cr, Mg and A1 oxides. Such material has probably better chemical and thermal properties that may. be useful for foundary and refractory applications. Two flow-sheets for the beneficiation of the chromite concentrates using carho- and oxychlorination are suggested.

Jan 1, 1997

By D. L. Yopps

Platinum-group metal (PGM) flotation .. concentrate from the Stillwater Complex, MT, was subjected to biooxidation using Thiobacillus ferrooxidans in an effort to break down the sulfide minerals and liberate the ? associated PGM&apos;s for subsequent chemical leaching. Bacterial treatment oxidized up to 94 pct of the sulfide present, destroyed the PGM-bearing pentlandite [ (Ni,Fe),9Ss) mineralization, and dissolved most of the nickel in the concentrate. Results showed that increased sulfide oxidation during the biological stage led to improved PGH recovery in the subsequent. chemical leaching stage. cyanidation at 80° c proved to be the best chemical leachant tested. It removed 7.6 pct of the palladium, 94 pct of the rhodium, 97 pct of the gold, but only 34 pct of the platinum from the biooxidized concentrate.

Jan 1, 1991

By Rodney J. Ishak

The reduction of Mn3O4 to MnO has been investigated in a thermobalance apparatus. The charge was composed of manganese ore (decomposed by heating/calcination or pre-reduction to mainly Mn304) and coke. The material was charged to a crucible, which was suspended in the balance. CO-gas was distributed through a grid in the bottom of the crucible. Two sizes of ores were used; 2.4-4.8 mm and 6.7-9.5 mm. Coke particles were in the size range 4.8-6.7 mm. Experiments were conducted in the 900-1100°C temperature range. The composition of the product gas was monitored continuously. External mass transport between bulk gas and particle surface does not seem to limit the rate of reduction. Assuming that both diffusion through product layer and chemical reaction at the interface between MnO and Mn304 are rate controlling, the data was tried both in a shrinking core model and in a grain model using regression. The grain model gives the best physical description of the process, because the reactant is in fact a porous medium. With this model the effective diffusivity was calculated to be in the 1.5-6.10-5 m2/s range. The pore size was mainly between 0.1 and 10 um.

Jan 1, 2003

By Jorge Alberto Soares Tenório, Romano Espinosa, Felipe Fardin Grillo, José Roberto de Oliveira, Denise Crocce

"The aim of this work was evaluation of the recovery of Zn and Fe of the EAFD added to the hot metal in the form of briquette at temperature of 1500°C. The EAFD was agglomerated by cold briquetting and introduced in the hot metal. This study utilized a bench-scale equipment to melt, during this process to kept a flow rate of inert gas above the bath. Were collected periodically metal samples and the samples were analyzed for determination of the content of total silicon and carbon by chemical analysis. Zinc oxide, zinc ferrite and other oxides were reduced and were volatized and collected by a cleaning system of dust (baghouse) located on top of the oven. More than 98% of iron were recovered from EAFD during the test. It was possible to produce a dust containing about 68% zinc by means of adding of EAFD.IntroductionIn the first semester of 2010, steel production was about 706 million tons, 27.9 % more than in the first half of 2009. Not a significantly increase if 2010 data is compared with the first semester of 2007 (only 7.2 % higher), before the world’s economic crises. Steel production is divided into two main routes. The first one, and most used, is the Basic Oxygen Furnace Process (BOF process), which in 2008 accounted for approximately 67.1 % of steel production. The second route is carried out in the Electric Arc Furnace (EAF) that in 2008 represented 30.6 % [1 ].Electric arc furnace dust (EAFD) is a solid waste generated during the steel making process. It is classi?ed according to NBR 10004 as dangerous solid waste-class I, because the elements Pb e Cd leach in water exceeding the maximum limits permitted by the NBR 10004 [2 ]."

Jan 1, 2012

"EAF dust is categorized as a hazardous solid waste. EPA approves only two treatment methods: either sending the dust to zinc recycling facility, or stabilizing it first and then disposing it to a specially-lined landfill. Both treatment methods are costly to EAF steelmakers. In order to reduce the cost and even better to make profit from the dust, EAF steelmakers need to find a costeffective technology to separate zinc from EAF dust. This paper is dedicated to discussion of a novel recycling strategy: in-process separation of zinc from EAF dust. The concept of in-process separation of zinc from EAF dust is first defined, and then a simple Zn concentration model is developed. From this model, two approaches of in-process separation of zinc from EAF dust are derived: (1) prematurely capturing dust at very high temperature when zinc is still in vapor status, (2) prematurely collecting dust immediately after quickly cooling EAF off-gas from high temperature to low temperature. Next, thermodynamic analysis is conducted to understand zinc behavior in EAF off-gas. It is demonstrated in theory that zinc is in vapor status while it exits from electric arc furnaces. At last, recycling routes and economics of in-process separation of zinc from EAF dust are discussed.IntroductionElectric arc furnace (EAF) plays an increasingly important role in steel production. According to USGS, steel production from electric arc furnaces has long exceeded that from basic oxygen furnaces [JJ. In 2009, electric arc furnaces produced 64% of total steel in the United States.Along with the fast growth of EAF steel production, generation of EAF dust is also rapidly increasing. A survey by AIM Market Research showed that 10 - 20 kg EAF dust was generated for every ton of EAF steel produced [2] In 1999, the United States alone produced 770,000 metric tons of EAF dust [3] In Europe, annual generation rate of EAF dust is more than one million tons [4-5]. In Japan, about 450,000 tons of EAF dust is produced each year [6] Globally, total generation of EAF dust was estimated to be more than 5 million tons per year [5] EAF dust is categorized as a hazardous solid waste since it often contains heavy metals, such as lead, chromium and cadmium. US Environmental Protection Agency (EPA) approves only two methods for treating EAF dust: (1) recycling the dust by EAF-dust recyclers, and (2) specially landfilling the dust for disposal after it is chemically stabilized. These two methods of treating EAF dust are both very costly to EAF steelmakers. It was estimated that a fee of $150 to $200 per ton of EAF dust was paid for various treatment options, which added approximately $2 - 3 cost for every ton of liquid steel produced by electric arc furnaces [?J."

Jan 1, 2011

By I. Perus, M. Fazarinc, G. Kugler, M. Tercelj

"Ledeburitic tool steels are highly alloyed steels used for specific highly loaded applications but are characterized by low and variable hot workability. In this contribution the importance of selecting the right choice of some essential process parameters, i.e. casting temperature, solidification rate and soaking temperature, needed for improving the intrinsic hot deformability of ledeburitic tool steels, is studied. An inappropriate selection of casting temperature and cooling rate results in precipitation of unusual eutectic carbides that decreases the hot workability, whereas with the selection of appropriate soaking temperature the temperature range of safe hot working can be broadened. For each initial as-cast microstructure individually determined soaking temperature should be selected.IntroductionThe surface cracking during hot deformation of ledeburitic tool steels reduces mechanical properties and their industrial yield. These tool steels have high hardness, wear resistance and high tempering resistance on one hand, and high flow stresses and low hot deformability on the other. Decreased hot deformability of the tool steels is attributed to the type, size, shape, distribution, fraction of eutectic carbides and/or other phases, grain growth, etc. at upper limit while precipitation of secondary carbides and decreased recrystallization rate at lower limit of the safe hot deformation temperature range, [1-6].The occurrence of cracks on most exposed areas of workpiece are related to the areas where similar conditions related to upper and/or lower limit of temperature working range prevail, i.e. areas with accelerated cooling, areas with higher value of accumulated strains where also decreased recrystallization rate with simultaneously presence of higher tensile stresses takes place, furthermore areas of workpiece which are due to combustion conditions in furnace heated to higher temperatures, etc. Thus the areas, where combination of previously mentioned conditions prevails, are more exposed to cracking. This additionally requires that hot deformability of ledeburitic tool steel should be considered as a complex problem. Publications in the literature with regards to hot deformability of tool steels are predominately of a partial nature thus all reasons for unexpected occurrence of cracks are not sufficiently explained in available literature so far. Furthermore modern practice proves that previous processing parameters significantly influence the hot deformability and thus this cannot be considered as a constant value. During heating, soaking and hot deformation various processes take place: decay (decomposition) of carbides, formation of new carbides, dissolution of carbides and of alloying elements, etc. Thus depending on variation of process parameters and chemical composition, that consequently influences the processes related to carbides, shifting of decreased deformability at both limits of temperature working range to higher and/or to lower temperatures can occur, [1-14]."

Jan 1, 2012