Search Documents

By Mitsuru Tanahashi

In order to develop an effective process for the production of from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at a solar-grade silicon (SOG-Si) 1773K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten M6-8 followed by oxygen gas injection into the melt (Two-stage connecting process). II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection Process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By I. A. Ibrahim, A. K. Ismail, A. A. I. Afifi

"Synthetic rutile for paints industry is conventionally produced by a combined smelting and leaching process. Smelting process is an energy intensive step and represents economic burden in view of the increasing energy costs. Egyptian ilmenite ore containing 40% TiO2 and 38% total Fe was thus directly leached with sulphuric acid to produce eventually synthetic rutile. The process-involves digestion of the ore with sulphuric acid whereby both TiO2 and Fe are dissolved. The solution was then treated with iron powder to convert Fe3+ to Fe2+ to avoid co-precipitation of iron during the hydrolysis step. After solid/liquid separation and clarification, Fe was crystallized as ferrous sulphate hydrate by chilling. The titanium pregnant liquor was concentrated by evaporation and then hydrolyzed to precipitate hydrated titanium dioxide which was then calcined to produce synthetic rutile containing 98.6 TiO2 and 0.58% Fe2O 3. The optimum conditions of all the processing stages were determined.IntroductionSynthetic rutile for paints, welding rods and other industries could be produced from ilmenite ore by sulfuric acid leaching process. This process is a batch process and nearly 80% of all TiO2 produced in the world is made by this process [1]. Figure l shows simple block flowsheet of the process. The process involves the following stages.Digestion: In this stage, ilmenite ore is treated with concentrated sulfuric acid where both iron and titanium are converted to their respective sulfates according to the following equations:"

Jan 1, 2000

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

By Mamoru Kuwahara, Tomohito Taki, Masamichi Sano

"Theoretical basis and experimental results on ultrasonic separation of dispersed inclusions from molten metal are outlined. Transitional formation of an ultrasonic standing ·wave field in a liquid bath is numerically predicted based .on the wave equations. Numerical solution of the equation of motion of a fine particle in a standing wave field indicates that the inertia term can be neglected during conventional ultrasonic separation of fine particles: Analytical solutions for the position at which particles are coagulated the minimum power for separation, and the ultrasonic separation time are derived to incorporate such key process parameters as the density difference and the acoustic energy density exerted. Cold model experiments have been carried out to observe ·transitional coagulation of polystyrene particles in an aqueous sugar solution with the incidence of standing ultrasonic plane wave. Experimental results agree well with the theoretical predictions.IntroductionDespite of recent progress of fundamental and applied researches in metallurgical systems, advanced materials· with less inclusions and better properties may demand more innovative processing in a: molten state. It may be realized by applying electromagnetic and/or ultrasonic external fields to the systems. The present authors1)·2) have been proposing : new methods of ultrasonic processing of materials based on such phenomena as acoustic streaming, acoustic radiation pressure on dispersed phase in a standing wave field, and the cavitation in liquid associated with use of high-intensity ultrasound and so on. Taking account of common physical natures between ultrasound and sound wave, we call such · a processing assisted by acoustic wave as ""sonoprocessing"". This report ·deals with some theoretical and technological aspects on the ultrasonic separation of fine particles from liquid, which could become an important operation to produce clean materials. Fundamental theory and ·supporting experimental results will be given below to give an insight into the liquid metal sonoprocessing."

Jan 1, 2000

By S. Ellor

The development of models of INCO's Copper Cliff operations using a computer spreadsheet program is discussed. Empirically developed metallurgical relationships were utilised. The paper concentrates on models of the pyrometallurgical processes but discusses applications such as optimisation of operating parameters, evaluation of feed changes and custom or recycle materials processing. The models were initially developed using a spreadsheet program on a personal computer. The requirements of plant engineers and process operators for significant increases in operating speed led to the transformation of some of the modules. The paper is presented in two parts: 1. The development of the modules using a spreadsheet. 2. The transformation of a module into a high speed tool for process control. The application of the technique to other pyrometallurgical processes is discussed.

Jan 1, 1992

By P. A. Manohar

This paper describes an implementation of the Potts model for simulation of grain growth in 2D on a distributed-memory parallel architecture. The simulation scheme utilizes a continuous-time, asynchronous parallel version of the n-fold way algorithm. Each Processing Element (PE) carries a piece of the global simulation domain while the virtual topology of the PEs is in the form of a square grid in 2D and Torus in 3D. Different PEs have different local simulated times. Inter-processor communication is carried by the Message Passing Interface (MPI) routines. Sample results for grain growth simulation in 2D are presented for a 840 x 840 global domain size distributed over 16 PEs. The grain growth kinetics obtained in the simulation of pure, isotropic systems is in good agreement with the theory. Grain size distributions obtained in the parallel simulation are well described by the lognormal distribution, thus validating the simulation procedure. Keywords: Metropolis algorithm. n-fold way algorithm, asynchronous parallelization, grain growth

Jan 1, 2003

By Tuula Mäkinen

In 1959 Outokumpu started up an integrated nickel smelter and refinery at Harjavalta. The flash smelting ? Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes by leaching and electrowinning. In 1995 the production capacity was increased from 17 000 mtpa to 52 000 mtpa, based on the Direct Outokumpu Nickel Smelting Process. The additional refinery capacity is based on hydrogen pressure reduction, producing nickel powder and briquettes. The smelting operation is currently part of Boliden Group and the nickel refinery part of OM Group. In the DON technology, high-grade nickel matte with low iron content is produced in the flash smelting furnace directly without subsequent converting. The metal values in the smelting slag are recovered in an electric furnace as an iron containing Ni-matte. The mattes produced differ from the conventional nickel mattes in many respects, and therefore focused R&D efforts have been made in order to cope with their melting points, fluidities and settling properties. When developing and operating metallurgical processes it is crucial to manage and control the characteristics of the products as well as by-products generated in different steps of the process chain. The low melting points of the high-grade nickel mattes produced in the DON furnace, particularly those low in copper, have pointed out challenges in the furnace design, in particular in the hearth and its thermal engineering. Also key issues of the DON technology are smelting of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of PGM`s and cobalt. These factors can be affected by a proper selection of the process concept, and the operational conditions in the processing vessels. This paper deals with the experience of the DON technology gained over the first ten years of operation, including the significant environmental impacts. Selected results of the thermo-dynamic modelling of DON and EF mattes and high-magnesia slags are reviewed, with the reference to the mattes produced. Also the design principles of the FSF and EF will be discussed.

Jan 1, 2006

By Hartmut Rossel

VAW aluminium AG has built a "Recycling-Technikum" (Recycling Research Centre) to add a new arm to the company's Corporate Research and Development Department. The Recycling Research Centre, a pilot plant for scientific research, has been in operation since September 1993. These state-of-the-art facilities allow the investigation and optimisation of recycling techniques in 'a global way and in detail. Research is concentrated on the unit operations - processing, melting and waste-gas purification - with the available installations making it possible to compare different alternative process combinations on a 100-kg scale. One of the main targets of VAW research is the development of recycling techniques for packaging. The paper presents an approach to recover the aluminium contained in flexible packaging materials using an integrated melting and waste-gas purification system.

Jan 1, 1995

By Wenbo Luo, Kang Liu, Fusheng Mao, Jilai Xue, Jun Zhu, Chunlei Yang

Extracting alumina from coal fly ash (CFA) is of great interest for both environmental protection and recycling valuable alumina content. In this study, ultrasonic aided leaching process as an effective method was investigated to enhance extracting Al2O3 from CFA via concentrated sulfuric acid sintering. The influence of ultrasonic power and processing time were tested under the conditions as the same as those without ultrasound. It is found that the alumina extraction rate can reach 90.5 % with ultrasound assistance, while the ultrasonic treatment can reduce almost 15 ~ 30 min in leaching time and 5 ~ 10 oC in leaching temperature than those without ultrasonic operation at the same Al2O3 extraction rate. In addition, the ultrasonic can reduce calcium content by 6 ~ 8 % dissolved into the leaching liquid. SEM analysis also shows that the residue particle size with ultrasound is smaller than that without ultrasonic treatment.

Jan 1, 2015

By Robert M. Leary

The Kennecott Utah Copper smelter operates two Outokumpu flash furnaces: a smelting furnace for production of high-grade matte and a converting furnace for production of blister copper. Flash furnaces typically possess several characteristic features that must be considered in process control development such as long lag times associated with settler volume, non-linear input and output responses, large process gains, and unmeasured disturbances. Additionally, the Kennecott smelter possesses certain unique characteristics which must be considered such as single mine concentrate source, limited concentrate blending capacity, and feed preparation facilities that inevitably cause significant lags between furnace control parameters and manipulated set points. In order to improve furnace control and on-line time, a process control system was developed to address these issues. The feed forward control module provides predictive control and operates in response to furnace feed input changes. The feed back control module provides responsive control and is based on furnace output deviations. To provide regular feed back information to the control room supervisors, new sampling methods were developed which provide the operators with molten metal and bulk material samples at regular intervals to provide information for control. The control system was implemented on the Flash Converting Furnace in May 1999 and on the Flash Smelting Furnace in August 1999.

Jan 1, 2000

By P. A. Davidson

"We discuss the influence of a static magnetic field on jets, vortices and turbulence. This is particularly relevant to D.C. braking in slab casting. Our main conclusion is that, typically, the magnetic field destroys mechanical energy, via joule dissipation, but is unable to destroy momentum. Rather, it continually rearranges the momentum in such a way that the energy falls.IntroductionIt is well-known that a static magnetic field can suppress motion of a liquid metal. That is to say, movement of the liquid across the magnetic field lines induces a current. This leads to Joule dissipation and the resultant rise in thermal energy is accompanied by a corresponding fall in kinetic energy.This phenomenon has been exploited in a range of metallurgical processes. For example, in the continuous casting of large steel slabs, an intense, static magnetic field is commonly used to suppress motion within the mould. The objective is to keep the free surface of the liquid quiescent, thus avoiding the entrainment of surface debris. In other solidification processes, such as techniques for growing semi-conductor crystals, it is widely believed that natural convection has a detrimental effect on the metallurgical structure of the solid. Again, the imposition of a static magnetic field is seen as one means of suppressing these unwanted motions. Finally, magnetic damping is used in the laboratory measurements of chemical and thermal diffusivities, particularly where solutal or thermal buoyancy can disrupt the measurement technique.In this paper we shall look at the damping of jets, vortices and turbulence. Our aim is to present a unified theoretical framework from which the many published studies may be viewed."

Jan 1, 1999

By James D. Navratil

Advances in hydrometallurgy require the introduction of new separation and purification processes, but they can be complex, costly and energy intensive. Chromatographic processes have low energy requirements and possess very high separation efficiencies. However, they have not yet made the great industrial impact that might be expected from their benefits. The large-scale and difficult separation of rare earths would greatly benefit from an improved continuous chromatographic operational device. Truly continuous, multicomponent chromatographic separations may be achieved by means of the continuous annular chromatograph. Work has been Initiated at The University of New South Wales involving the improvement and development of such equipment for the separation and purification of rare earths.

Jan 1, 1990

By Mao Chen, Tim Evans, Zhixing Zhao, Weidong Zhang, Baojun Zhao, Dongqing Wang

High temperature softening behaviours of iron blast furnace feeds (sinter, lump and pellet) have been determined under conditions simulated to the blast furnace. The industrial samples were packed with sandwich structure (coke / ore / coke) in graphite crucibles and 30 CO / 70 Ar gas mixture was blowing directly through the bottom of the crucibles. The displacement and temperature were continuously recorded simultaneously to construct the softening curves. Separated quenching experiments were also carried out at selected temperatures under the same gas atmosphere. The temperatures were selected corresponding to the turning points of the softening curves. The phase assemblages and composition of each phase in quenched samples were analysed by Electron Probe X-ray Microanalysis (EPMA). The proportion of the liquid formed at temperature was obtained from the backscattered electron images. The deformation characteristics of these complex multi-phase materials are shown to be related directly to the phase assemblages of the samples and the microstructures. FactSage was also used to assist the predictions of liquid / solid fractions and their compositions.

Jan 1, 2015

By Dai Xi

In the present work, the viscosities of molten FenO-MgO-Si02 and FenO-MgO-CaO-Si02 semi-synthetic slags for nickel flash smelting were measured in the temperature range from 1473 to 1723K by a rotational viscometer. The ratio of Fe to Si02 was fixed at 1.2, calcium and magnesium oxide contents varied in the range from 2 to 8 mass% and 9 to 12 mass%, respectively. The results showed that silicate anions became smaller by increasing CaO content, which results in a decrease of the viscosity of the slag. In the case of MgO addition the viscosity behavior was complicated. At MgO content below 11 mass%, the viscosity increased with the increase of MgO at all temperatures tested. However, when the MgO content was above II mass%, the viscosity decreased slightly for FenO-MgO-CaO-Si02 system. At higher MgO contents, low-viscosity slags can be obtained by adding CaO. At a given composition, the viscosity decreased with increasing temperature. The higher the temperature, the more MgO can be added before saturation. The effect of Fe304 on the viscosity was quite significant. The viscosity of slag increased by 300mPa's at l573K when Fe304 content varied from 3 to 9 mass%. The viscosity values are presented as the functions of temperature and composition. A comparison between FenO-MgO-Si02 and FenO-MgO-CaO-Si02 systems is given in this study.

Jan 1, 2003

By Staff

The uninitiated, first-time visitor to the Copper Cliff Smelter of The International Nickel Company frequently finds it strange that the world's largest nickel producing works is located at a site seemingly named in honour of another metal. Industry-wise persons who know The International Nickel Company through its nickel producing, fabricating and sales organizations can be just as surprised to learn that Inco's annual copper production from the Sudbury area mines nearly equals that of nickel. But when the history of the mines and smelters of the Sudbury district is reviewed it is impossible to separate the stories of copper and nickel. In fact, going even further back in time (I), it was due to the similarity in appearance of the nickel bearing mineral niccolite (NiAs) to that of copper ore that led nickel to be tagged with the rather uncomplimentary name of kupfer-nickel or Old Nick's Copper - The Devil's Copper. This was in approximately 1650 and it would take another hundred years, until 1751, before Axel Cronstedt of Sweden obtained nickel in its pure form and permitted it to take its own place in the family of metals. One hundred more years passed before mining came to northern Ontario and approximately one hundred thirty before the beginnings of development of the Sudbury Basin.

Jan 1, 1976

By Karl A. Gschneidner

The magnetocaloric effect has been known for 120 years and has been utilized for cooling about 70 years. But in the last four years significant advances have been made to show that magnetic refrigeration is a viable and competitive cooling technology. Most of the work has focused on reciprocating devices, but rotary apparati are being developed. To date the magnetocaloric properties have been characterized for more than 200 materials. The magnetocaloric effect behaviors have been classified into three types of behaviors. The most common one is found in magnetic materials which exhibit a second order magnetic phase transition. Magnetic materials which exhibit a first order magnetic phase transition account for the second group of materials. Materials which exhibit multi-magnetic phase transitions make up the third group. The best candidate materials for magnetic cooling over the range from -4 to -1 350 K are also presented.

Jan 1, 2002

By H. P. Wang, E. M. Perry

"Analytical solutions for investigating the solidification of casting problems with initial superheat and natural boundary conditions have been derived using an integral method. There are two moving interfaces in the solution field, one for the phase change line and the other for the superheat line. Two coupled nonlinear differential equations, representing two moving layers, were calculated by the Runge-Kutta numerical integration scheme. The solutions are in terms of six dimensionless parameters: phase change number, two Biot numbers for interfaces, diffusivity ratio, and dimensionless superheat temperature and time. Parametric studies on these parameters have been conducted to provide generic information about this phase change problem. This analytical information is extremely useful for validating numerical solutions. A simplified I-D finite element model was constructed for the purpose of comparison. The excellent agreement between the analytical and finite element solutions has proven that they are mutually validated.This validated finite element modeling tool was then used for modeling an investment casting process of a super-alloy with a simple geometry: a two-step plate. The nonlinear latent heat release, a common property of alloy materials, was approximated by several piecewise linear segments. The transient temperature response of this 2-D finite element solution, including a metal/mold gap resistance, shows excellent agreement with experimental data.This fundamental work provides a solid basis for further work on the development of a process modeling tool for the complex investment casting process.IntroductionAt present, the investment casting process is used in a variety of industries. In the aircraft engine industry, in particular, investment casting is used to produce parts ranging from turbine blades to engine frames. Because a large single casting can replace many component parts that require machining, fabrication, and assembly, this one-piece casting approach becomes a very cost-effective manufacturing process.The main constraint in using this process for mass production is the long design-to-production lead time. The standard rigging design is still an art, based on the experience of casting experts, rather than on scientific methods. Many trials are often required before making a sound final casting. In order to .reduce the number of expensive casting trials, the development of computer-aided tooling technology is needed.The fundamental physics describing this manufacturing process can be simply described. They reduce to a solid/liquid phase change problem, with two parts - first, the thermal balance of the initial superheat temperature of the molten metal and the preheat temperature of the ceramic shell through heat conduction, and second, the energy release from the mold surface to the ambient by radiation."

Jan 1, 1986

By Olga A. Gomon, Alexey N. Lozhko

The technology of heat treatment for metal frequently includes multiple fast heating and cooling of the products surface. If the product is heavy-weight or long-size, its moving from a zone of cooling to a zone of heating and return require a long time. Other important condition of ensuring qualitative surface at heat treatment is intensification of cooling phase. It is known that turbulization of a flow activates heat exchange and increases efficacy of cooling without increasing volume flow rate of water. Additional difficulty is to ensure the regularity of heating and cooling on length of a product. The technology of cyclic heat treatment of rolling products, at which mobile zone of turbulent heat exchange is formed on the surface of a product, was developed and realized. The submission of water occurs through to face spray systems. Each of the systems has six long-range atomizers, which are located circularly. Two flows of water move towards one another along a surface of a product. When they collide, the right zone of turbulent heat exchange creates heat transfer in this zone of 10-15 time more intensive than on other surface of a product. The effect of moving turbulent zone on length of a product is reached by changing the proportion of volume flow rate of water, which is created by face sprays. The speed of movement for turbulent zone along a surface of a product is chosen so, that the cooling takes place on a small depth only. Then after passing the turbulent zone over a determined site of a surface, its temperature recovers fast owing to hot internal layers. The parameters of process were determined by mathematical simulation of cooling in an installation. The equations for dynamics of movement of collision point of flows, which were received this way, are interesting supplementary products of research. The experiments show that frequency of movement of turbulent zone is an important technological parameter. It defines mechanical properties of a surface and should be chosen depending on a profile of product and metal grade. The results of comparison of mechanical properties of a surface of various rolling products, which were received by developed and conventional technologies, are described in this report. Dependence of regularity of mechanical properties on frequency of movement of turbulent zone is adduced.

Jan 1, 1998

By Bogidar Mihaylov

A laboratory study was conducted on continuous precipitation of copper, cadmium, mercury and arsenic using thiourea, thioacetamide, sodium sulfide and ammonium sulfide as precipitating agents. Depending on the experimental conditions the metals precipitate with the sulfide donors at different orders and rates. These differences were employed as a basis of several techniques for continuous separation of copper and arsenic, cadmium and arsenic, mercury and copper, and copper, mercury and arsenic. The separation of the metals from industrial waste solutions was also studied. The precipitates obtained were inspected using x-ray diffraction, scanning electron microscope, atomic absorption spectrometer and plasma particle counter.

Jan 1, 1992

By Vanessa M. Torres

Cia. Vale do Rio Doce is currently developing Niquel do Vermelho Project. The laterite deposit is located at Carajas Mineral Province at less than 15 km from Sossego Copper Project, scheduled for start-up in 2004. The available infrastructure, includes paved roads, large capacity railroad and port complex owned by CVRD, power supply and good quality water. The project was evaluated in the past for ferronickel production. In the late 1990s, CVRD switched its attention to investigating the usage of pressure acid leaching. The combination of good metallurgical behaviour for pressure acid leach (PAL) process route with reasonable mineable grades, and existing infrastructure justified the start of engineering studies in 2002. The project approach at the engineering phase is based on the dual objective of minimizing risks while maximizing project profitability and value. CVRD is currently completing the Niquel do Vermelho prefeasibility study. This paper outlines the main outcomes of the study and future perspectives for the project.

Jan 1, 2004