Search Documents

By J. K. Owens

As part of a larger research effort focused on ground control, the U.S. Bureau of Mines is currently evaluating the effectiveness of using stereological analysis for characterizing mine roof strata. Input for a stereological analysis of a rock mass is best obtained by scanning (imaging) the walls of clean drill holes using a video-imaging borescope or other video device. Two classes of features are being investigated: (1) Lithologic types that comprise the overall rock mass and (2) structural discontinuities (e.g., joints, foliation, bedding planes) within a given lithologic unit. In the former, the volume fraction of a given Lithologic unit in relation to the entire rock mass can be estimated. In the latter, the mean intercept length between adjacent structures and surface area density of the geologic structures can be estimated. Examples of sampling procedures and subsequent computations are presented for several situations using information collected from drill holes in roofs of underground mines. One such example is based on the trace of a cycloid curve used as a stereological sampling path on the cylindrical wall of a drill hole. Stereological measures, such as intercept length, volume fraction, and surface area density, are explained in the context of rock mass characterization.

Jan 1, 1994

By Michael J. Friedel

The fundamental problems associated with ground control reflect the inability of mining personnel to "see" the development of anomalous conditions. Toward this end, the U. S. Bureau of Mines is investigating the application of seismic refraction tomography for imaging the process of pillar yielding, at the Foidel Creek coal mine, near Steamboat Springs, CO. The inherent three-dimensional problem of imaging coal pillar stress is reduced to a single plane by considering only the stress transmitted from the pillar to the adjacent floor rock. This approach exploits the fact that refracted seismic energy is essentially confined to the adjacent higher velocity sandstone strata. The tomographic analysis using ray-tracing based on wavefront migration resulted in a robust P-wave tomogram from which regions of high velocity indicate zones of high stress concentration, whereas low velocity zones indicate regions of stress relief. The interpreted region of high stress concentration occurs at the pillar end nearest to the working face of the adjacent longwall panel. This finding is corroborated by vertical pressure cell measurements recorded in the pillar. The stress diminishes toward the pillar perimeter with local minima correlating to the locations of observed pillar spalling. Time-sequence monitoring, as the longwall face advances, is recommended for evaluating changing stress conditions.

Jan 1, 1993

By M. Karmis

For several centuries surface subsidence has been recognized as an inevitable consequence of most underground mining. In fact, British court records of disputes and litigations related to property damage due to mining subsidence can be traced to the early fifteenth century (Shadbolt, 1978). The first systematic investigations of the mechanisms involved in mining subsidence can be credited to Belgian Mining Engineers. The re- search effort was initiated after the widespread movements and the resulting structural damages suffered by the City of Liege in the 1920's. The publication of Gonot's 1871 treatise "Loie de la NomZ" (normal theory) was one of the most not- able achievements of the Belgian school of that era (Gonot, 1871). During the past 100 years the phenomenon of mining subsidence has been the subject of intensive research, particularly in Europe where long- wall is the most common method of underground coal mining. Many theories have been advanced to explain the mechanism of ground movement as it develops from the excavation, through the superincumbent strata, to the surface. Such theories include the original concepts of beams, arches, domes and the contemporary mathematical modeling principles of strata movement assuming two extreme concepts-- a continuous elastic medium and a stochastic medium for the superincumbent strata. An excellent review of the development of these theories ?-s given by Shadbolt (Shadbolt, 1978). In conjunction with the theories of mass strata movement in the vicinity of mine workings, the subject of surface subsidence predictions has also been the subject of extensive research. The development of reliable and rational techniques of subsidence prediction is imperative, if this phenomenon is to be recognized and controlled within acceptable environmental levels. Empirical as well as mathematical methods have been proposed to fulfill this objective and a comprehensive analysis of these methods has been presented in the literature (Bramer, 1973; Shad- bolt, 1978; Virginia Polytechnic Institute and State University, 1980). As a result of this intensive research effort, it is now accepted in many )coal fields-- mainly in Europe-- that the state of art in subsidence prediction and control has approached a level where mining induced surface displacements can be predicted to a suggested accuracy of less than + 20 percent. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented. In this country, subsidence is rapidly gaining emphasis as an important environmental problem of underground coal mining. Damage resulting from this phenomenon ranges from land settlement to severe structural damage and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). Yet, the art of subsidence prediction and hence control in this country, for both longwall and room-and-pillar coal mining, is far from approaching the maturity reached by the Europeans. In this paper, field measurments and computer modeling techniques have been used to develop some basic relationships of longwall subsidence and its related parameters. Because the objective of this study was to develop regional subsidence trends, all processed information pertains to the Appalachian coal region.

Jan 1, 1981

By J. D. Dizon

Conventional strata control methods (i.e. roof bolts. cable trusses) are not always effective for ground control of very weak coal strata. An alternative method, termed presupport. is being investigated by the U.S. Bureau of Mines. In this paper structural modeling of presupport conceuts and field teatinn of a DresuDuort application is presented. Pinite-elem&; modeis indicate that forepoles significantly lower beam stresses in the roof strata overlying a coal seam. but they cannot he expected to prevent or reduce I roof strata failure at the coal face due to the presence of a high stress concentration at that location. However, their presence near the coal face is needed to sustain the fall of roof if it does occur. Because of an ever present severe stress concentration at the coal face, it would appear that stresses could exceed material strengths, causing local structural damage, especially if the rock is very weak. Therefore previous coal face positions along an entry may have a higher than normal probability of roof fall. In the field investigation. a loorcost air injection test has thus far shown promise as a tool for evaluating that effects of forepoling on the roof strata. Observations of coal mine en- tries in which forepoles have been installed indicate forepoling is effective in controlling very weak roof strata.

Jan 1, 1990

By N. P. Kripakov

The U.S. Bureau of Mines (USBM) is conducting research to develop a practical computer-based tool that will allow coal mine planners to anticipate rock mass behavior surrounding mine entries prior to actual mining. More specifically, this tool estimates to what degree and extent the immediate roof and floor strata and the coal pillar ribs surrounding an opening will weaken or fail for a given set of mining parameters. The technical approach couples together two numerical techniques: the boundary-element method and the finite-element method to allow for an approximate three-dimensional simulation of actual mining situations. Outputs from plan-view, linear-elastic, boundary-element models executed at different mining stages are used as input to a detailed, section-view, finite-element model to estimate the degree and extent of failure expected to occur around the periphery of an entry system. Using a pseudo-elastic approach. elastic rock mass properties are continually updated as different zones are predicted to fail. The procedure is relatively easy to use and is being set up to work interactively with the user who will not be expected to be a computer expert. Inputs include easily understood parameters obtainable from the field and rock mechanics laboratories. Examples of computer-generated output from generic sample models representing typical mining situations are presented and results discussed.

Jan 1, 1994

By Stephen C. Tadolini

The U.S. Bureau of Mines (USBM) is conducting research to provide alternatives for traditional secondary support methods. These cost-saving methods are proving to afford safer installation, improve entry stability, eradicate material-handling injuries associated with crib supports, and enhance ventilation. In cooperation with Mountain Coal Company, the USBM replaced timber cribbing with high- strength cable supports to provide stability in a gate road that was used for two longwall panels. The support design consisted of 2.1-m (7-ft) full-column resin-grouted bolts and 4.8-m- (16-ft-) long high-strength resin-grouted cable supports. Three support concepts were evaluated: passive, stiff, and tensioned systems. Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during panel extraction. The stress and loading histories for both panels and the abutment and yield pillars were monitored to assist in evaluating the stress transfer and pillar performance in conjunction with the roof behavior. The test results indicated that resin- grouted cable support systems successfully maintained the immediate and main roofs during the extraction of two longwall panels. This paper describes the theory, application, and advantages of resin-grouted cable supports and presents the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1994

By Francis S. Kendorski

Underground stone mines tier construction aggregates and industrial minerals are being planned in increasing numbers throughout the United States. At the middle of the last century (1950s) underground stone mines were much more common, and characteristically had no thorough site characterization other than proving reserves and trial-and-error planning. Ground control employed was minimal. Consequently, there was a tendency to conduct minimal pre-mining studies. However, the deposits that lend themselves to little site characterization and minimal ground control are few today, with the best being mined out. Failures of a number of underground stone or similar mines from that era are more common than realized, Underground stone mines almost always use some combinations of square or rectangular pillars, sized to support the overburden load, and spaced to allow the use of larger, more-efficient equipment. Heights are controlled by the available stone quality, interbeds of waste, or technological or safety considerations. Prior to committing to a specific mine plan with subsequent significant capital investment, and prior to having available the wealth of knowledge and experience gained once mining underground, a safe and workable mine layout must he achieved. Early attention to the several different rock units involved (roof, mine level. floor) and their strength as a rock mass with the inherent discontinuities, will allow first approximations of acceptable mine geometries and sequencing.

Jan 1, 2000

By M. G. Schuerger

The United States Steel Mining Company, Inc., (USM) Lynch District, operated the No. 37 Mine in the Harlan coal seam, Harlan County, Kentucky, from 19'2 until its sale to Arch of Kentucky in 1984. Overburden depth varied from 400 to 2000 feet and mining height varied from 8 to 12 feet. In 1981, because of deep overburden, high seam height, and previous pillar stability problems, U. S. Steel Research and the Lynch Mining District entered into a joint project to measure longwall pillar stress. Eight gateroad pillars were instrumented with a total of 86 vibrating-wire stressmeters under overburden depths varying from 500 to 1550 feet. Stress-increase measurements were taken during: (1) pillar development, (2) retreat of longwall panel No. 1, and (3) retreat of longwall panel No. 2. Total average pillar stress was approximately three times the pre-mining stress with total stress at an individual meter reading 5.5 times the pre-mining stress. When maximum, measured average pillar stress was compared to pillar strength predicted by several popular pillar design methods, the pillars were found to be stronger than predicted. This paper will summarize the pillar instrumentation program and present the results. Stress distributions, average measured pillar stress, and comparison of measured pillar stress to predicted pillar strength by several design methods will be given.

Jan 1, 1984

By Murali Gadde

U.S. coal mines? primary roof supports typically consist of passive resin bolts; however, the use of active bolt systems is increasing. Despite this widespread use, a comparative performance evaluation of these bolt systems has not been done under similar geologic conditions. The performances of three commonly used primary bolt systems were investigated: fully grouted passive rebar, fully grouted tension rebar (using two speed setting resin), and resin-assisted rebar with mechanical anchors. In order to investigate the performance of these bolts, strain gauged bolts of all three types were installed at three different coal mines as part of a larger research project funded by the National Institute for Occupational Safety and Health (NIOSH). This paper addresses the initial installation bolt loads measured at these mines. Analysis of the data showed much lower installed loads on active bolts than is traditionally assumed. It appears that the active load on bolts bleeds off relatively quickly under geologic and operational conditions similar to those at the studied mines. The data also showed that within a short time span after installation, the measured loads on active and passive bolts did not differ significantly. This paper compares the results from over 20 bolts of each bolt type that were all 1.8-m (6-ft) -long, 20-mm (0.804-in) nominal diameter Grade 75 rebar and discusses the relevance and shortcomings of the data and bolt performance.

Jan 1, 2011

By K. Hanna

This manuscript describes an extensive ground control study at the Inland Steel No. 2 Mine near McLeansboro, IL, conducted by the U.S. Department of the Interior's Bureau of Mines (USEM) in cooperation with Inland Steel Coal Co. The mine experiences severe ground control problem primarily due to high horizontal stress, particularly at entry intersections. Mine experience has shown that reorienting mine entries, modifying the bolting pattern, and altering the mining sequence are effective in reducing the severity of roof falls and out-of-seam dilution. However, the frequency of roof falls has not been significantly reduced. This research project was designed to provide a thorough explanation of the intersection failure mechanism through combined analyses of company in-mine experience and Bureau field measurements. Stresses and deformations were monitored in a four-way intersection during all stages of development and were related to site observations and theoretical analyses. The results of the combined analyses indicate that high horizontal stress is the predominant factor contributing to intersection roof falls in the Inland Steel No. 2 Mine. The horizontal stress induces shear zones to form along the outby 1 ribs, causing the immediate roof layer to detach 1 and behave as a cantilever beam oriented diagonally across the intersection and parallel to i the maximum horizontal principal stress. As the shear zone progresses upward, roof layers successively detach and fail, forming a dome-type roof fall.

Jan 1, 1986

By Frank E. Chase

A massive pillar collapse occurs when undersized pillars fail and rapidly shed their load to adjacent pillars which in turn fail. This chain reaction-like failure may involve hundreds, even thousands, of pillars and the consequences have been catastrophic. One effect of a massive pillar collapse can be a powerful, destructive, and a potentially hazardous airblast. On eleven recent occasions, massive pillar collapses have occurred in six southern West Virginia coal mines. Two other instances of massive pillar collapses in U.S. mines have been documented in the literature. Research was conducted at four mines where massive pillar collapses occurred. Geotechnical evaluations of roof rock, coalbed, and floor conditions were made. Evidence indicates that in each case a massive and competent roof rock unit was able to bridge a relatively wide span, creating a pressure arch. Eventually, the pressure arch apparently broke down, and the structural characteristics of the pillar system were such that sudden, massive pillar failures occurred. Data collected at the failure sites also indicates that all the massive collapses occurred where the pillars width-to-height ratio was 3.0 or less. Numerical modeling, performed with a modified version of the MULSIM/NL computer program, supports the conclusions that the extent of the mined-out area, the bridging capability of the main roof, and the width-to-height ratio of the pillars are probably all significant factors in the occurrence of massive pillar failures.

Jan 1, 1994

By Thomas M. Barczak

The engineering of a support system is driven largely by economics. The goal is to provide effective support at minimal cost. For this reason, wood has been extensively used as a support material for centuries. The cost of timber for mining applications has risen by more than 50% in the past 5 years and is likely to continue to increase as the supply diminishes and further environmental restrictions are placed on timber harvesting. The increased cost and lack of high strength wood in the Western United States has provided incentives to improve the utilization of wood and to develop alternative support materials. This U.S. Bureau of Mines' (USBM) report discusses the basic engineering requirements for the application of various materials for supplemental roof support construction and provides an overview of support systems that use materials other than wood. A comparison of support performance and cost for various material constructions is made to assist the mine operator in support selection. The scope of materials discussed in the report include: (1) conventional mine timber loaded perpendicular to the grain, (2) parallel to the grain timber loading, (3) steel fiber reinforced and air entrained concrete, (4) steel, (5) granular fill materials, and (6) combinations of these as composite support structures. The range of support systems analyzed include wood and concrete cribs, concrete columns and props, steel beams, friction props, and several novel support concepts.

Jan 1, 1994

By Douglas C. Peters

Part of the ground control research at the U.S. Bureau of Mines is involved with improving ground control data collection and analysis methods. A geographic information system (GIs) is being used within this research effort to standardize the data collected and provide a common graphical and tabular format and analysis system for researchers to access information on underground coal mines. In addition, GIS's can perform relational analyses on multiple map and tabular data sets which are not possible through map-creation or CAD packages or through data bases alone. In addition to standardizing ground control analyses, there is an increasing need for rapid analysis of ground control data in connection with increasing production rates at longwall mines. The examination of a large number of interrelated parameters and their impact on short-term mine safety and productivity under the time constraints imposed by rapid production requires computer-aided techniques. A GIs provides the means to quickly, quantitatively, and reproducibly evaluate mine-wide conditions. This overview of GI8 techniques for mine data integration and analysis, using a mine in Colorado as an example site, will cover the input of data into a GIs, including mine-wide monitoring system data and general data such as roof control plans and geology. The methods to geographically reference these data sets and retrieve and combine them also will be covered. Automation of such processes briefly will be reviewed to allow future users to automate their mine data analyses.

Jan 1, 1990

By Gennaro G. Marino

Site conditions at several shallow room and pillar mines in Illinois are described and compared with the charac¬teristics of the subsidence profiles at the ground surface. The shape and magnitude of the subsidence profiles were found to be closely related to the thickness of the soil and rock over-burden the percent extraction of the coal, and the shape of mine pillars. The room and pillar mines were located at a shallow depth (from 112 to 220 ft), beneath flat to gently rolling terrain. Thickness of the coal seams ranged from 5 to 9 ft and at all sites was underlain by underclays. This information has been developed in order to improve techniques for evaluating the subsidence potential at sites within the Illinois coal basin. he results presented form a small portion of the work carried out by the University of Illinois with Illinois Abandoned Mined Lands Councils and the U. S. Bureau of Mines at the Minneapolis Research Center in Minnesota (Marino and Mahar, 1985). Presented in the paper are the modes of mine failures observed for Illinois room and pillar mines, an overall summary of the site geologic and mining condi¬tions, case histories of each mode of failure, a comparison of sag profiles, and then an empirical relationship between the site conditions and the maximum sag subsidence. The most ideal case histories are presented to illustrate fundamental behavior. A brief of the Paper is given in a summary and conclusions section.

Jan 1, 1984

By Stephen C. Tadolini

Cable supports offer several advantages over traditional secondary support methods. Cable supports enhance stress redistribution to pillars and gob areas, minimize or eliminate timbers and cribs which reduce ventilation capabilities, eradicate material handling injuries related to the placement of crib supports, and provide a cost-effective alternative to secondary support. The U.S. Bureau of Mines has designed and installed cable supports to improve the stability of tailgate entries in an underground western coal mine. Two entries closest to the Iongwall panel were solely supported with high-strength cables installed with cement grout. Basically, with modifications in the intersections, 360 ft of roadway nearest the longwall panel was supported with two rows of 22-ft-long cables installed on a 7-ft spacing. Approximately 250 ft of a second bleeder entry was supported with two rows of 16-ft¬long cables installed on a 7-ft spacing. Individual cable loads were monitored with hydraulic U-cells and pressure pads. The roof behavior was simultaneously monitored with differential magnetic sag stations and closure meters on 25-ft spacing during longwall panel retreat to evaluate the response of the immediate and main roofs. Cable supported gateroads appear to be a viable alternative in secondary support when compared to wood timbers and cribs. This paper describes the theory, application, and advantages of cable supports and presents the results of the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1993

By Jun Lu, Greg Hasenfus

"In this paper, the mining experience and challenges for the first right-handed longwall panel in the Pittsburgh seam are introduced. The longwall headgate T-junction experienced very high face convergence (up to 2 feet), accompanied by roof sag, floor heave, and rib loading. The headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded.Different underground instruments, such as a roof scope, de-gas drill, tell-tale, laser meter, and Borehole Pressure Cell (BPC), were employed to explore the roof geology and to monitor the entry convergence and the stress changes in the pillar. In addition, the impact of other geologic factors, such as large overburden depth, laminated sandstone roof geology, soft floor, and large headgate equipment, were also analyzed. Subsequently, geotechnical solutions were provided to avoid or mitigate the impact of these challenging geologic factors.INTRODUCTIONIt is well known that high horizontal stress will affect the stability of roof, floor, and ribs within underground mines. In general, the headgate entries will experience stress concentration for the right-handed longwall face. On the contrary, the stress concentration will be in the tailgate entries for the left-handed longwall face (Hasenfus and Su, 2006). Without the stress shadow, the stress concentration in the headgate for the first longwall panel may be more significant (Figure 1).A mine in the CONSOL Pennsylvania Operation was extracting the first right-handed longwall panel in the Pittsburgh seam, which created high horizontal stress concentrations at the longwall headgate. Because of concern over soft wet floor within the syncline, floor coal had been left in place on development. Early on, upon retreat, the longwall headgate T-junction experienced very high face convergence, accompanied by roof sag, floor heave, and rib loading. The floor heave was exacerbated by the presence of floor coal, which buckled upward near the center of the beltline. Roof movement was occasionally aggravated by laminated roof conditions, but was kept in check by aggressive supplemental support including cable bolts, yielding props, cribbing, and roof mesh. Rib bolting and rib mesh helped to further maintain the entryway stability by keeping sloughage at a minimum. Nevertheless, despite the heavy support, headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded."

Jan 1, 2018

By Nielen van der Merwe

The data base of failed pillar cases as used by Salamon and Munro (1967) in their original analysis to determine the strength of coal pillars empirically, has been updated for this study. It is shown that the Vaal Basin and Klip River coal fields exhibit similar behaviour, i.e. failure at high safety factors within a short period of time after their creation. Those collapse cases have been omitted from the new data base. New failures that occurred after 1967 have been added, except for those that occurred in the Vaal Basin and Klip River coal fields. (1967) a technique to minimise the area of overlap between the populations of failed and intact pillar cases, the new data base was re-analysed in conjunction with the original Salamon and Munro (1967) data base of intact pillar cases. It was found that a linear formula reduced the overlap area by 22%. The new formula predicts higher strength for pillars with a width-to-height ratio greater than approximately 2S and a lower strength for smaller pillars. For most current South African coal mining conditions, using the new formula for pillar strength will result in leaving smaller pillars without sacrificing stability. The reason for this is that the Salamon and Munro (1967) formula underestimated the strength of larger pillars and overestimated the strength of smaller pillars. The potential benefit for the South African coal mining industry amounts to saving reserves equal to the total production of two large mines per year.

Jan 1, 2002

By Thomas R. Scotese

A rock mechanics instrumentation and monitoring program was implemented during pillar extraction at Gulf Mineral Resources' Mt. Taylor Mine, the deepest uranium mine in the U.S. Three types of monitoring were employed: (1) drift convergence around stopes (using a portable tube extensometer), (2) stress changes in pillars (using vibrating wire stressmeters in horizontal boreholes), and (3) load changes in haulage ways under stopes (using vibrating wire load cells in jack stands). Results include convergence-time graphs, convergence contour maps, stress-time graphs, a stress increase contour map, load-time graphs, and abutment load limit maps. Major factors influencing results include (1) size of pillars around the extraction area, and (2) presence and orientation of a major fault adjacent to one extraction area. These factors, combined with pillar extraction, produced evidence of load transfer over 120 m from a stope measuring only 55 m x 45 m. Vertical stress increases of 7 to 17 MPa (1000 to 2500 psi) within 60 m of the stope were obtained using the stress- meter manufacturer's method. The fault apparently prevented load transfer in the down-dip direction but increased load transfer in the up-dip direction. Convergence rates of up to 1.3 cm/day (0.5 in/day) were measured at two stations. Instruments were generally reliable despite adverse underground conditions. The instrumentation and monitoring program at Mt. Taylor provided a warning system against ground control problems and a characterization of ground behavior for future development and extraction of pillars. Recommendations are made for future mining and instrumentation practices.

Jan 1, 1984

By Jisheng Han

Interaction effect exists when two or more neighboring seams are mined. The mining activity in one seam causes stress redistribution and strata movement in both the roof and floor. When the thickness of interburden between two neighboring seams is small, some hazardous situations like roof cutters, roof falls, floor heave and rib spalling in one seam may be encountered due to the effect of the mining activity in the other seam. An investigation about roof cutters, roof falls and floor heave was conducted in a West Virginia mine to study the interaction of multi-seam mining. The mine is mining the Sewickley Seam, which is about 90 ft above the Pittsburgh Seam which was mined in the 1960's using room and pillar method. The roof falls and other stability anomalies of entries observed underground in the Sewickley Seam were found closely related to the location of barrier pillars and gas well pillars left in the Pittsburgh Seam. Then numerical modeling was carried out to check the interaction between these two seams of mining. It was found through the modeling results that in the areas where pillaring operation was conducted in the Pittsburgh Seam, the stress concentrated less in the Sewickley Seam while near the edge of the gas well pillars and barrier pillars, high stress concentration was observed. It was concluded that under the geological conditions of the study mine, the entries stability would be affected by the lower seam mining activity, especially above or around the edges of pillars.

Jan 1, 2005

By Megan N. Witkowski

The purpose of this study is to investigate the susceptibility characteristics of domestic and agricultural water supplies that may be vulnerable to diminution or total loss of supply when active longwall mining is in the vicinity of the potable aquifer systems of southwestern Pennsylvania. The study focuses on water supplies in Greene and Washington Counties with reported losses or reductions in supply that were attributed to the seven active longwall mines in operation between 2003 and 2008. The undermined water supplies represent a variety of hydrogeological settings and mining conditions prevalent in the southwestern Pennsylvania longwall coalfield. The susceptibility characteristics investigated include hydrogeological setting, proximal location to mining, and climatic conditions at the time of impact. The investigation considers the relationship between geological and mining characteristics. Geological characteristics include overburden composition and geomorphology of the surface; mining characteristics include mining method, depth, and extraction thickness. It was determined from the study that the average overburden thickness at each mine site is indicative of hydrological changes to potable aquifer systems, with the overall impact frequency at each site decreasing as depth to mining increases. However, depth to mining was not the governing factor when hydrological responses were determined on a case-by-case basis. To fully analyze and hopefully predict potential impacts by longwall mine subsidence, it is necessary to consider additional factors including topography, distance to mining, mining method, and climatic conditions at time of undermining. The investigation serves the purpose of enhancing our understanding of hydrogeological responses to longwall mining and will aid in predicting potential impacts to southwestern Pennsylvania?s wells and springs in proximity to future mining.

Jan 1, 2011