Search Documents

By D. W. Fuerstenau, S. Raghavan

This paper presents a brief summary of some of the thermodynamic aspects of flotation processes. Thermodynamic considerations that control interfacial and wetting behavior in mineral/water/air systems are discussed. Particular attention is given to the thermodynamics of collector adsorption.

Jan 1, 1976

By R. Schuerch, C. Cimiotti, G. Anagnostou, J. Nickerson, P. Perazzelli

"This paper presents experiences gained from the construction of the Lake Mead Intake No. 3 project. The 4.7 km long tunnel was excavated with a hybrid TBM (able to operate in both closed and open mode). The tunnel crossed metamorphic and sedimentary rocks under a hydrostatic pressure of about 14 bar. During the excavation of the tunnel the TBM encountered difficult ground conditions caused by a combination of high water pressure, poor ground quality and locally low depth of cover. The adverse conditions required the TBM to be driven in closed mode at very high support pressures (10 – 15 bar) for approximately 60% of the tunnel length. The paper summarizes the main problems encountered during TBM excavation and analyzes the evolution of the TBM parameters over the entire tunnel length. INTRODUCTION The Lake Mead Intake No. 3 project is located approximately 30 km away from the city of Las Vegas in Nevada, USA. The project consists of the construction of a deeper third intake for the biggest reservoir in the United States, which is formed by the Hoover Dam. The construction of the new intake was required due to the constant drawdown of the lake level (more than 40 m in the past 20 years) and the consequent risk that the shallower intakes 1 & 2 may run dry. The project included the fabrication and positioning on the lake bottom of an intake riser, the excavation and lining of a 185 m deep shaft and construction of a 4.7 km long tunnel. One peculiarity of the project is that the water table is located about 140 m above the tunnel elevation (i.e. corresponding to a hydrostatic pressure of 14 bar at the current lake level). The tunnel was constructed using a tunnel boring machine (TBM) able to operate in both open and closed mode (Mc Donald & Burger, 2009). The present paper focuses on the TBM tunneling experience gained from the Lake Mead Intake No. 3 tunnel. The TBM excavation started on December 27, 2011 and finished on December 10, 2014 with the breakthrough to the intake structure at the bottom of Lake Mead. GEOLOGICAL CONDITIONS The assessment of the ground conditions encountered during construction was mainly based upon qualitative descriptions of the tunnel face conditions (during open mode operations) and analysis of the extracted muck (during closed mode operations)."

Jan 1, 2016

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By T. Winkler, J. Tokarczyk, D. Michalak, W. Chuchnowski, M. Dudek

Engineering Methods aiding Sustainable Development of Mining Systems will be presented, and especially: virtual prototyping for designing of Mining Systems with Health Protection and Safety criteria taken into consideration, modelling and assessment of technical and health hazards that can occur during operation of Mining Systems, creation of knowledge repositories that disseminate safe work methods with consideration of existing language and culture barriers, dissemination of the methods integrating world community and Mining Systems users.

Jan 1, 2011

By N. L. Piret, R. J. Wesely, A. E. Melin, A. D. Zunkel

At the end of the sixties new iron precipitation techniques as jarosite, goethite or hematite brought about the new generation of electrolytic zinc plants, thereby terminating the multitude of existing neutral leach residue treatment schemes. Since the eighties, increasing environmental impact considerations urge the conversion of these contaminated waste generating precipitation processes to techniques which either produce environmentally acceptable residues or minimize their formation thereby generating iron-bearing byproducts. Technologies identified and economically assessed include the hematite process either suitably improved or with subsequent upgrading, the iron extraction process and the direct smelting of neutral leach residue to slag and fumed zinc oxide.

Jan 1, 1993

By T. Cohen

Technological innovation in the minerals industry must be driven by the need to improve performance according to social, as well as environmental, safety, efficiency and production criteria. This paper outlines the possibilities and rationale for incorporating constructive technology assessment into technology research and development within the CSIRO Minerals Down Under National Research Flagship (MDU). The paper develops a process of Social License in Design that attempts to address the future social challenges and opportunities of a technology during development by utilising forecasting techniques and accounting for the perspectives and values of decision makers and likely stakeholders. Interviews with senior technologists and social scientists within MDU reveal the institutional context into which the Social License in Design process is to be situated and highlight key factors that may inhibit or enhance its uptake.

Jan 1, 2011

By M. M. Botz

Cyanidation tailings which are disposed in a surface impoundment experience a loss of cyanide due to natural degradation, frequently reducing the cyanide concentration to very low levels. Quantifying cyanide losses in terms of pond geometry, local weather conditions and feed solution chemistry has been largely empirical though in many cases mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or an effluent limitation. To permit a more quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, WAD and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared against data collected for a North American tailings impoundment during 1998.

Jan 1, 1999

By Greg T. Saretzky, Wilson G. Ward

A comprehensive hydrologic study was completed far the waste rock dump at Equity Silver Mine, BC. Characterization of the hydrologic system included geologic structure. topography, surface hydrology and groundwater systems. The results of the study conclude that the cover system is restricting net infiltration to approximately 5%. However, significant discharge continues to occur from the perimeter of the dump. A three dimensional seepage analysis was carried out to illustrate the influence of groundwater discharge associated with the regional topography and geologic structures. The results of the modelling program show that groundwater discharge occurs from the waste rock dumps when high recharge rates are specified for the surrounding topography- This groundwater discharge strongly influenced by the high hydraulic conductivity assumed far the fractured bedrock. The modelling results are considered preliminary and field drilling and piezometer installation is being conducted to determine the groundwater regime in the vicinity of the waste rock dump.

Jan 1, 2000

By James R. Dunn

The nature of water and clay in carbonate rocks is currently being investigated at Rensselaer Polytechnic Institute by various thermal and sorption techniques. Two basic concepts 'led to the present research. (1) To explain the expansion and contraction on wetting and drying of some unsound argillaceous carbonate rocks, it was postulated that the pore space around each clay particle is such that when water is sorbed by the clay, force is exerted against the pore walls. (2) The clays in expansive rocks are rejected from the growing dolomite crystals during their growth, and form a more or less connected network, thereby becoming "wettable," or available to water. New quantitative cold differential-thermal-analysis (electrocalorimetric) equipment was designed and constructed to check the "limited space" and "wettable clay" concepts and to determine the thermal nature of the transition of water to ice in rocks. This DTA equipment can detect the release of heat in freezing of less than 0.001 per cent water in a rock. Twenty-three rock cores (nine sound and fourteen unsound) and 4 procelain cylinders for standards were studied. In the nine sound rocks and in all the procelain cylinders, the rapid freezing of from 50 to 100 per cent of the water was readily detectable after 7 to 10° C of supercooling. No further freezing could be detected to -20° C. However, in eleven of the fourteen unsound rocks, no freezing was detected to as low as -40° C; in the other three, less than 50 per cent of the water froze. As a check of the DTA measurements, adsorption isotherms were determined for all materials. Calculations of theoretical freezing points for sorbed water again demonstrated that the least sound rocks had the most nonfreezable water. "Frost" sensitivity in these carbonate rocks is, therefore, probably not the result of the force of expansion of water to ice. The disruptive force is believed to result from expansion of sorbed, ordered water on clay surfaces. The relationship between the unfilled rock pores after 24-hour water saturation and the water sorbed at 85 per cent humidity at 30° C (i.e., the theoretical nonfreezable water delineates the sound and unsound carbonate rocks.

Jan 1, 1966

By S. K. Mukherjee, A. W. Laurito, M. M. Singh, N. I. Jayaraman

This paper describes the application of foam to control respirable dust in a double-drum longwall mining section. The feasibility of injecting an adequate quantity of foam through the shearer drum was initially established in the laboratory. Thereafter, underground testing of the foam system to determine its effectiveness on an active operating longwall was conducted in a mine in West Virginia. The foam system proved superior to the water spray system. The details of the laboratory and field investigations, the results obtained, and the degree of acceptance of this system by the mining company are discussed in this paper.

Jan 1, 1987

By Richard C. Marshall

The heightened concern over the environment which has developed in recent years has caused activities on National Forest lands to come under more intense public scrutiny. This has been especially true for activities oriented toward the production of commodities. Cattle grazing, mining, timber harvesting, and oil and gas leasing and drilling have all been increasingly subject to appeal and litigation. As a result, environmental analyses being conducted by the Forest Service have become more comprehensive, and measures to reduce or eliminate adverse impacts on resources have been given more attention. The costs of such environmental mitigation measures can be significant even when viewed in the context of the millions of dollars a company may spend, for example, to develop a mine. Using the Montanore Project in northwestern Montana as a case study, this paper examines the costs of alleviating some of the detrimental effects which may occur as a result of a mining operation. Although many of the general issues that have been raised about Montanore are common to other mineral projects, the scale of the project, as well as the fact that the ore body is within a wilderness area, the site is in grizzly bear habitat, and the surface waters are considered to be pristine, all combine to make Montanore particularly challenging from an environ- mental standpoint. Much of the information which follows is contained in the most recent version of the Draft Environmental Impact Statement (DEIS) which is scheduled to be published in several weeks. Based on agency and public comments, some of the information presented in the paper will change before the Final Environmental Impact Statement is issued in 1991.

Jan 1, 1991

By M. T. Worley

Joint Development Associates International, Inc. (JDA) began humanitarian relief and community development in Central Asia in1992, following the collapse of the former Soviet Union. Appropriate technology has played an important role in their efforts to assist those segments of society that are most vulnerable to poverty and disease. Three case histories are described to illustrate the successful implementation of simple, but effective technology in community development.

Jan 1, 2004

The floatability of a bituminous coal in NaG solutions was evaluated using a modified Hallimond tube to delineate the role of the electrostatic interaction between bubbles and particles in determining the coal hydrophobicity. Zeta potential measurements showed that bubbles are negatively charged in the entire pH range tested, while coal particles are positively charged below pH 6.0 and negatively charged above it. Also, both sodium and chloride ions were confirmed to act as indifferent ions without any specific effects for both coal particles and bubbles. Flotation as a function of pH exhibited a maximum and minimum at low salt concentrations which is shown to be determined mainly by the coal hydrophobicity as measured by a new hydrophobic levitation technique. At high salt concentrations (above 0.1 mole/dm3), the flotation without such maximum or minimum is controlled by the electrostatic interaction between the bubble and the particle.

Jan 1, 1992

By Clinton Strachan, Rob Dorey

10.1 INTRODUCTION This chapter presents considerations which should be applied to heap leach pad site selection, site evaluation, and design, relative to the geotechnics of the site and ore. 10.1.1 General Guidelines are presented covering the topics encountered in design and construction of heap leach faci1ities. Because geotechnical characteristics vary from site to site, not all geotechnical topics associated with a specific heap leach facility are presented, and there may be exceptions to some of these guidelines. The general features of a heap leach facility (from Chapter 1) to be discussed in this chapter are: • Leach pad (including leach pad foundation and liner); • Heap; • Solution storage faci1ities (for pregnant and barren process solutions) ; and • Solution collection facilities (which collect and convey solutions in the heap and convey them to solution storage facilities). These general features are illustrated in Figure 10.1. Liners for these facilities are discussed in Chapter 11. Solution application systems and the sizing aspects of solution storage facilities are discussed in Chapters 6, 7, and 12. The general features listed above are constructed with and overlie naturally occurring materials (such as ore, borrow soils, and subsurface soils and rock). These natural materials are relied upon to perform in an acceptable manner as a component of the leach facility (such as the liner, drain material, and foundation).

Jan 1, 1988

By Fathi Habashi

METALS COMMONLY leached may come from one of the following sources: 1) Occurring in nature in the native state, e.g., gold, silver, platinum metals, copper. 2) Produced as by-product of a metallurgical process, e.g., gold, silver, platinum metals, selenium. 3) Produced by reduction of an oxide ore, e.g., copper, nickel. GOLD AND SILVER Cyanidation According to Mellor (1923) the alchemists of the eighteenth century knew that gold was soluble in aqueous solution of potassium cyanide, and the early jewelers probably utilized this fact in gilding. He also mentions that Scheele in 1783 and later Bagration in 1843 noted the solvent action of aqueous solutions of alkali cyanides on gold. Yet it was not until 1887 that the value of this observation was recognized, when MacArthur and Forrest (1887) made use of it in leaching gold from its ores. Since then, the process has spread to every gold and silver mining district in the world.

Jan 1, 1970

By John F. Papp

Chromite is used both as a metallic and nonmetallic mineral. Chromite ore is used as the source of chromium by the metals industry and is used, without chemical alteration, in the refractory and foundry industries. Chromite ore is also the source of chromium for the chemical industry. On average worldwide far more chromite ore is used by the metallurgical industry than by any other industry. Thus, although the primary purpose of this chapter is to describe the nonmetallic uses of chromite, the metallurgical uses must also be discussed in order to provide a complete description of this commodity.

Jan 1, 1994

By S. W. Swerson

25.1-THE PURCHASING FUNCTION The word "purchase" means "to obtain by paying money or its equivalent; to buy for a price." This definition is all too simple to properly describe the word "purchase." One should consider the basic objectives of purchasing-to procure the right material, of the right quality, in the right quantity, at the right time, from the right source at the right price. Here it should be noted that in purchasing it is recognized that the best quality or grade of materials may be the only grade to purchase for a specific job. However. there are other jobs where the medium, standard or poor grade of materials is the right quality, as the lesser grade will perform adequately. In some companies the purchasing department makes the decision as to the right quality, while in others this function is shared with other departments. Years ago in business the owners controlled the purchase of required materials and services by performing the task themselves. The owners obtained the type materials and services they needed and paid the price demanded. This function was performed along with all the other duties requisite to the owner of a business, namely, clerical, hiring and firing of personnel, financial management, etc. As companies grew in size, clerical duties were assigned to other personnel and the owner usually retained the purchasing authority. This same division exists today in many small companies. However, in the larger companies, the purchasing function has been assigned to a separate department. Importance of the Purchasing Function-The larger the company the greater the need for a separate department to perform the purchasing function. Today the purchasing agent for most larger progressive companies has policy-making authority. Therefore, it is reasonable for him to report to the president or vice president of his company. Studies of several hundred companies show the purchasing department head reporting to top management 87.5% of the time. This fact in itself is indicative of the importance of recognizing that effective purchasing requires a department staffed with specialists in the field of procurement with knowledge and experience sufficient to perform in today's complicated business atmosphere. In the manufacturing field it is a common axiom that usually half of the company's dollar expenditures are for materials. If a purchasing department functions properly and the right product or service is purchased and a savings accomplished, the contribution to the net profit of the company is much greater, as opposed to sale dollars, where only a small portion is carried forward to net profit. Thus, the importance of the purchasing department and the contribution it can make to the success of the company are obvious. 25.1.1-THE PURCHASING FUNCTION 1. Responsibilities of the Purchasing Function-The purchasing agent in performing his function is acting as an agent for the company and others in the company requiring materials and services. Accordingly, he is committing the company for materials and services subject to certain limitations which the board of directors may stipulate. In view of this, the purchasing agent,'^ position must of necessity he

Jan 1, 1973

By Michael Gay, W. H. Hansmire, G. Rippentrop, V. S. Romero

The new Tren Urbano heavy rail transit project in San Juan, Puerto Rico has one very significant part, the Río Piedras Contract, being constructed underground. This paper will give an overview of the tunneling work that started construction in1997. Design-Build procurement for tunneling is addressed. The new and modern transit system in San Juan will be 17.2 km (10.7 mi)long and have 16 stations in its first segment of construction, which is due to open in 2001. The line connects the city center district of Santurce to the outlying suburban municipality of Bayamón. All construction is being done under design-build contracts as a demonstration project funded by the Commonwealth of Puerto Rico and the Federal Transit Administration (FTA). The Río Piedras Contract is completely underground and involves practically all types of construction in soft ground. One station is built as cut-and-cover at the University of Puerto Rico. One portion has twin tunnels to be driven with an Earth Pressure Balance Machine (EPBM) and lined with one-pass precast concrete segments. Another has four short tunnel drives at a turnout that will be constructed with an initial support of shotcrete and lattice girders (i.e., the New Austrian Tunneling Method of construction). The most complex construction is the Río Piedras Station, which is being built as a stacked drift with a total of 15 individual tunnel drifts. After being sequentially excavated and concreted, they will form the arch of the 19 m (62 ft.) wide by 16 m (53 ft.) high cavern station. This structure is excavated in soil with less than 5 m (16 ft.) of cover to overlying historic buildings.

Jan 1, 1999

By Edgel P. Stambaugh

Oxides are important for use in the production of metals, ceramic hardware, paints, permanent magnets, magnetic recording tapes and many other uses. In some of these applications, particle morphology, degree of crystallinity, purity, and homogeneity are relatively insignificant, while for other uses, these same properties are of critical importance. Many conventional processes are based upon recovery of the oxides from aqueous solutions by processes which include neutralization, evaporation of solvent, and precipitation of a complex salt. Consequently, many of these techniques lead to oxides of low quality. There is a growing demand for oxides of high quality, i.e., materials with narrow particle size distribution, controlled particle morphology, high purity, few structural defects, and high degree of crystallinity and homogeneity. This demand has prompted industry to search for new approaches for the manufacture of these special materials. One new approach for preparing high quality oxides is hydrothermal precipitation. This process has been used for preparing simple oxides such as ZrO2; mixed oxides such as ZrO2-SiO2; and complex oxides such as BaTiO3. These oxides were prepared in a high state of purity with a high degree of crystallinity and., in many cases, without the addition of precipitants. Many impurities- that are normally precipitated by conventional methods such as neutralization present no problem since they remain in solution. Nature of the process and its applications are discussed in this article.

Jan 1, 1977

By R. Schmidt

The computational fluid dynamics (CFD) technique was used to analyze and optimize the design of the dynamic air classifier integral to Raymond® Bowl Mills. Flow patterns and particle behaviors were modeled in the RB Bowl Mill equipped with various classifier designs. These CFD simulations resulted in the development of a hybrid turbine classifier that has now been field-tested, yielding significant improvements to both mill throughput and product size distribution. This paper demonstrates the viability of CFD as a tool for air classifier design and as a technique that can be extrapolated for use with other pulverizer and classifier arrangements.

Jan 1, 2004