Search Documents

By Donna L. Boreck

Introduction Coal has been mined in the western United States since the mid-1800s. The resource is abundant in the West. Despite recent economic conditions, it remains an important part of the nation's energy warehouse. Many of the seams that comprise the western resource base are thick, some exceeding 61 m (200 ft). Multiple, closely-spaced seams or thick coals that split into two or more minable seams are also common. Historically, subsurface development recovered from less than 15% to 50% of these deposits (Matson and White, 1975). This resulted in a substantial loss of inplace reserve due to the limited height that could be mined using the available technology. In an effort to increase future recovery from such deposits, the US Bureau of Mines analyzed the potential for incorporating three thick-seam mining methods into western coal mines. These methods are high-face longwall, multislice longwall, and longwall caving. They were developed in Europe and are being used to mine thick coal seams in Europe and Asia. One aspect that will determine their success in the US is the geology of the individual deposit; namely, are the methods adaptable to the geologic conditions characteristic of western coal? This paper analyzes some of the geologic factors that would affect development of thick or closely-spaced seams using these mining methods. Occurrence of thick and closely-spaced seams Since mining conditions and methods differ around the world, a thick seam is often defined as a seam whose total thickness cannot be extracted using the available equipment. In the western US, the maximum extractable mining height is about 4.3 m (14 ft). For this research, a thick seam was defined as a minable seam 4.6 m (15 ft) thick or more. Since one of the seams is usually lost using standard mining methods, closely-spaced or split seams were also addressed. These were defined as two minable seams 1.5 m (5 ft) thick or more separated by 9 m (30 ft) of interburden. Thick or closely-spaced coal seams are common in the West. Their importance has not been documented due, in part, to the methods used to measure resources. In the past, all reserves greater than 1.1 m (42 in.) thick for bituminous seams and greater than 3 m (10 ft) thick for subbituminous seams were grouped together and were differentiated only by rank. Further differentiation by seam thickness or minability was not done. For this reason, reserve figures for thick or split seams are difficult to determine. By analyzing available published resource data, Ferm and Muthig (1982) addressed thick seam resources. They estimated a resource of 90 Gt (99 billion st) of coal (16% of the Western resource base) in seams 4.6 (15 ft) or greater at less than 610 m (2000 ft) overburden. Yet, a later study of Pierce and others (1982) on one thick seam deposit in the Powder River Basin estimated a resource of 103 Gt (113 billion st). Pierce (1986) reported that the overburden reached a maximum of 731 m (2400 ft). The resources in this single deposit exceeded the 90 Gt (99 billion st) total projected for the entire western US by 12.7 Gt (14 billion st). Due to such differences, this author chose to look at reported occurrences of thick or closely-spaced minable seams in place of resource figures, to verify the need to research thick seam mining in the West. An occurrence was defined as an isolated site where a thick seam or two or more closely-spaced seams were reported. The occurrences were derived from published material - mostly mine descriptions, measured sections, coal exploration logs, and oil and gas logs. Due to time constraints, the reserves associated with each occurrence were not determined. All data points were random. The analysis was limited to occurrences in Colorado, Wyoming, and Utah. Although source material available to the author was limited to general coal summa-

Jan 3, 1988

By W. C. Wheeler, G. Suranyi, J. F. Gentleman, J. Muller, R. Kusiak

INTRODUCTION In 1974 two of the present authors reported the results of a pilot study indicating an increase of lung cancer risk in Ontario uranium miners. (Muller, Wheeler, 1973, 1974) The study was based on data contained in a computerized Mining Master File maintained by the Ontario Workmen's Compensation Board that contained information on miners examined in Ontario who had either 60 months of dust exposure in mines or had signs of pneumoconiosis or tuberculosis. Including the above conditions the definition of uranium miners added the condition of one month or more of uranium mining experience in Ontario. This list of Ontario uranium miners contained 8,649 names. Following the results of this first pilot study, we embarked on creating a file of uranium miners containing information on men with one month or more of uranium mining experience in Ontario without any further conditions. This file was used by the Royal Commission on the Health and Safety of Workers in Mines in their study of risk in Ontario uranium miners. (Hewitt 1976) This file contained 15,094 names. In this report we give an outline and progress report on a study of Ontario miners that we are conducting at present. It was felt that the male population of Ontario is not necessarily an adequate control population for uranium miners. A preliminary examination of the work history of uranium miners indicated that the majority of them (about 90 percent) had other mining experience in addition to their exposure in uranium mines. We therefore considered it useful to evaluate the possible effects of non-uranium mining on risk, and for this reason decided to make the Uranium Miners Study part of a study dealing with the mortality of Ontario miners in general. Aims of the Study The aims of the Study include the evaluation of: 1) the risk of dying by cause in non-uranium miners as compared to the male population of Ontario and Northern Ontario. 2) any differences that might exist in the death experience of non-uranium miners by cause according to ore mined. 3) the effect of length of exposure in non-uranium mines on age-specific risk by cause. 4) the dose-response function for primary cancer of the trachea, bronchus and lung from exposure to radon and its short-lived daughters. 5) the possible effect of the mining environment on deaths from causes other than cancer of the trachea, bronchus and lung. The study will address itself to a number of other factors that might well affect the dose-response function. These include: a) factors in the mine environment - other than radon daughters - that might affect lung cancer mortality. b) the effect of non-uranium mining on lung cancer risk in uranium miners. c) the effect of age as well as age at time of exposure on lung cancer risk. d) questions of latency and the possible dependence of latency on age at time of exposure. e) smoking as an important factor in lung cancer risk. f) Histological type of cancer in relation to the various parameters of exposure and age. MATERIALS AND METHODS The Study is making use of existing computerized data files and has set up certain new files. These include the Mining Master File and the Model Development File. The Mining Master File This file is a computerized record of data on individual miners obtained at yearly miners' examinations that have been carried out since the mid 1920's. The conditions for inclusion in the Mining Master File have been indicated above. Information contained in the file includes: (1) Identifying information: a) Surname and given names b) Date and place of birth c) Miners Certificate Number d) Social Insurance Number if available. (2) Updated Employment data obtained at each miner's examination: a) Year of first dust exposure in Ontario b) Year of first dust exposure outside Ontario c) Number of months worked in mining d) Ores mined e) Mining areas and mines f) Occupations

Jan 1, 1981

By A. T. Yu

Two major events highlight recent developments in US ore and coal ports: completion of the last series of modern taconite pellet transshipment facilities on the Great Lakes; and modernization and construction of coal ports, particularly on the East and Gulf Coasts. The New Taconite Transportation System To reduce raw material transportation costs, a fleet of new generation high-capacity 304-m (1,000-ft) self-unloading vessels were built to carry iron ore pellets from the Minnesota-Michigan iron ranges to the steel plants on the lower Great Lakes. Existing port facilities had to be modernized, revised, or completely rebuilt to accommodate these large vessels. Some of these were Burlington Northern's Allouez, WI, loading dock; Duluth, Missabe & Iron Range Railway Co.'s Two Harbors, MN, facility; Republic Steel's Lorain, OH, facility; and Chessie's Toledo, OH, dock. Allouez and Two Harbors receive taconite pellets from unit trains and load them onto large vessels either after dumping or via a large stockpile and reclaim system. The Lorain facility receives iron ore pellets from self-unloading vessels' discharge boom conveyor and reloads the pellets into rail cars or small vessels destined to inland steel mills. The Toledo facility receives Armco pellets from vessels, stockpiles them through the winter, and reloads into unit trains destined for Armco's mills along Chessie's rail tracks. Burlington Northern's $75-million Allouez pellet dock, completed in June 1977, was built to receive pellets produced by Hibbing Taconite Co. and National Pellet Plant in Minnesota, stockpile them through the winter when the lakes are frozen, and load them into 304-m (1,000-ft) vessels in the shipping season. As much as 10 Mt (11 million st) of pellets may be stockpiled within the loop track. A 6-km (4-mile) long conveyor system connects the stockpile area and the dock. Thirty-six new concrete silos were built on the dock to house 2 kt (2,000 st) each of pellets before shiploading. The $35.5-million expansion of the Two Harbors transshipment facilities began shiploading in July 1978 after ground breaking in Aug. 1974. Particularly noteworthy is the first application of the Orboom system-a breakthrough in technology for the modernization of the century-old pocket docks on the Great Lakes to accommodate the new generation of super vessels. The pocket-type loading dock has been a standard on the lakes for nearly a hundred years. Bottom-dump rail cars fill the ore pockets on top of a finger pier. Gravity chutes matching standardized ore ship hatch spacings are lowered to fill the holds of a 20.3-kt (20,000-dwt) ship. The construction is simple and the loading swift. In spite of advances in technology elsewhere, most of these docks continue to serve the iron ore and coal trade in the same manner they did in the 19th century. Although performance of the pocket docks on small vessels remains outstanding, the new 304-m (1,000-ft) vessels are beyond the reach of the old docks. After extensive development, the Orboom system (Patent No. 4,065,002) for pocket docks was successfully developed. The heart of the Orboom system is the retractable shuttle loading arm which loads the wide beam vessels. The Orboom shuttles are fed by existing pockets of the dock that, in turn, are charged by a tripper conveyor along the length of the dock. The Two Harbors shiploading system is supported by a 0.9 Mt (1 million st) storage-reclaim network. Unit trains are bottom dumped. Taconite pellets are stacked and reclaimed by bucket wheel reclaiming systems. Lower Lakes New Ore Ports At the lower Great Lakes receiv-

Jan 10, 1982

By Syd S. Peng

Introduction Modern longwall mining, introduced to the US coal industry in the mid-1960s, is the latest coal mining technique. Today, longwall mining produces more than 15% of all underground coal production. The growth of longwall mining in the US is slow. However, nearly two decades of longwall mining have demonstrated that its benefits outweigh the disadvantages. Longwall Advantages Production and Economics - A typical longwall production ranges mostly from 0.9 to 1.8 kt (1000 to 2000 st) of clean coal per shift. This is about three to six times the production of comparable continuous mining units. Furthermore, there are much less rejects in longwall mining, typically 15% to 25%. It must be noted, however, that a new longwall with an inexperienced crew may produce less, depending on mining conditions. But as experience gains, production increases rapidly. Due to its high production, the cost per ton of coal mined over the mine's lifetime is cheaper with longwall mining than with continuous mining. A study on a conceptual mine of 25 year life using actual operational data (Dangerfield, 1981) concluded that the cost per ton of coal mined is 32% cheaper by longwall than by continuous mining. Another benefit from its high production potential is that it enables the production to be concentrated in a few longwall faces versus many units of continuous mining required to achieve a similar production. As a result, mine organization and management simplify considerably. Safety and Savings - Most US longwalls use shield supports that cover the roof with solid canopy and isolate a gob completely from the face area. Thus, if the supports are properly selected and operated, the potential for roof fall accident is almost zero. Furthermore, it is not unusual that a well-run longwall face is much more orderly and cleaner that most well-run machine shops. The ventilation system for longwall mining is the most ideal type. It is simple and unique. No auxiliary fans are required. The fresh air sweeps through the whole face. Its volume and velocity can be adjusted as demanded. Recovery - In spite of multiple entries layout for US longwall panels, the longwall method recovers up to 40% more coal than the continuous mining method (Dangerfield, 1981). The typical recovery for longwall mining is 70% to 85% versus 45% to 80% for continuous mining. Versatility - Longwall mining has been employed successfully in seam heights ranging from 0.8 to 3.7 m (2.7 to 12 ft); in seam inclinations from horizontal to 35°; in overburden depths from 46 to 914 m (150 to 3000 ft); in single or multiple seam mining; and in uniform or irregular seam characteristics. For seam height less than 1.2 m (4 ft), the plow is used instead of a shearer. However, in spite of recent developments, the plow still is unsuitable for hard coal seams. Slow Acceptance How come longwall mining, with so many advantages, has not spread more rapidly? Undoubtedly, the major reason is the large capital investment required. Under normal market conditions, the capital required for a longwall panel ranges from $7 to $11 million. Another factor is the uncertainty of its applicability to any specific coal seam of interest where longwall has not been used or operated successfully. Although longwall mining elsewhere has proven its applicability to wide-ranging seam conditions, there have been several failures in the past two decades. Analyses of those cases show that most failures can be attributed to inexperience, both operational and technical, including equipment selection. Therefore, personnel training on the longwall mining technique is absolutely necessary before its initial operation. Some earlier statements about adverse surface subsidence associated with longwall mining were misleading. Research has proven that surface subsidence under longwall mining is controllable and predictable. And, if longwall mining was mandatory since the onset of coal mining in the US, there would be no surface subsidence problems over abandoned mined land today. It is a blessing that surface subsidence occurs

Jan 3, 1985

By Howard M. Graff

The Inland Steel Company operates five underground iron mines in the Lake Superior District. The two largest of these, from the standpoint of productive capacity, are the Sherwood Mine in Iron River and the Bristol Mine in Crystal Falls, both on the Menominee Range of Michigan. It is at these two mines that we have had our principal experience with belt conveyor installations underground, .At the Sherwood Mine, which has an annual capacity of about 450,000 tons, the first conveyor belt installationwas made in 1947 when conveyors were installed in the main haulage drifts on the 1200 ft, level, It was estimated at that time that approximately 5,000,000 tons would be mined from the stopes above the 1200 ft, level and. that if all this material could be moved to the shaft by belt conveyor, the entire cost of operation, including maintenance and the amortization of the equipment, would be about $,05 per ton, which was slightly more than half of what the cost would have been by conventional tramming methods employing locomotives and cars. Now, ten years later, the 1200 ft, level is almost completely mined out and we have actually removed. 5,200,000 tons and. the average cost of transporting this material to the shaft by belt conveyor has been $.095 per ton. Since there has been a substantial increase in hourly rate of pay and also in the cost of materials since 1947, we feel that the anticipated savings were very nearly realized., The 1200 ft, level installation at the Sherwood consisted of two 36" trunk line conveyors 815 feet long and 380 feet long, respectively, deliverying ore to the shaft. These in turn were fed. by three lateral 36" conveyors which paralleled the sides of the orebody, These gathering conveyors passed under draw points to which ore was brought from the stopes by mea S of scrapers or shaker conveyors, Shaker conveyors were used for a number of years in conjunction with the conveyor belt system of haulage but it was finally concluded that with this particular type of ore, the maintenance on shaker conveyors was excessive. Therefore, more recently, we have gone back to scrapers for the shorter distances and. are using belt conveyors in the scraper drifts for the longer distances. After this belt system had been in operation for about three years, it had proved to be so successful that it was decided to proceed with the same system or. a new level to be opened up 200 feet below. Instead of sinking the shaft and driving a horizontal drift to the orebody on the 1400 ft, level, an inclined conveyor drift was started near the shaft at the 1200 ft. level and driven downwards toward, the orebody at a slope of 15 degrees. The conveyor installed in this inclined drift is 36" wide, 990 feet long, is powered. by a 100 hp motor, and is capable of delivering 300 tons per hour to the 1200 ft, level shaft pocket. It is fed by lateral horizontal conveyors on the 1300 ft? 1400 ft., and 1425 ft, sub levels. Wien the inclined drift was started, the rock was scraped from the breast directly to the rock pocket at the shaft. As the distance increased., double scraping was employed, until the advance had reached 350 feet, At this point a portion of the final conveyor was installed, with a scraper slide near the breast, T e drift was then advanced be scraping on to the conveyor until a sufficient distance had been driven to permit the installation of an additional 200 feet of conveyor. This proved to be a very efficient and economical means of moving the development rock to the shaft and obviated the need of using cars or an inclined skip way, At the present time 85 percet of tie entire mine output is being mined below the 1200 ft, level and is delivered to the shaft via the inclined conveyor. The system appears to be working as well and as economically as did the conveyor systemonthe 1200 ft, level.

Jan 1, 1958

By Earl A. Berry

Someone once said, "The safest mine is one in which no one goes into." We all recognize this as being perhaps wishful thinking. We also recognize in it a certain amount of truth and an ultimate goal if we are optimistic. All of us are aware of the many things that have been done, are being done and will be done to reduce manpower in mining. For those of us; who are optimistic about this ultimate goal it would appear from the records-we are more than well on our way to the so called safest mine. Let us see what has been done in the past 20 years. T e period from 1935 to 1956. For example in the coal mining industry: In 1935 there were employed 462,903 men who produced an average of 805 tons per man per year or 4.50 tons per man per day. In 1955 there were employed 225,093 men who produced an average of 2,064 tons per man per year or 9.84 tons per man per day. There are no comparable figures compiled for the metal mining industry as a whole that can be broken down in this manner. However, from examination of figures available for different groups in metal mining there is a trend similar to that in coal mining. No-dbout the above figures reflect the intense development and perfection of machines and mining systems to tear out, transport and process our mineral wealth. The figures also show the mining industry has been able to double its production and at the same time reduce its manpower by half. When you compare the number of men employed today with the number which would have been employed 20 years ago to gain todays production at that time it become apparent that greater safety has been accomplished. For example the years 1935 to 1956 for all mining show. In 1935 there were approximately 649,226 men employed in mining and reports show 1,399 fatalities and 74,913 non-fatal injuries. In 1955 when there were 313,883 men employed in mining 496 fatalities and 25,365 non-fatal injuries were reported. To have produced the same tonnage of material in 1935 that was produced in 1955 it would have required the employment of approximately 1,298,452 men. 2,798 could have been fatalities and 149,826 could have had non-fatal injuries. You can now measure the full impact of what has been accomplished in the past 2o years by the aggressiveness of mine management, the wizardry of our engineering personnel and the thoughtfulness and devotion of our safety people and their programs. Therefore, there is a trend towards the goal of our opening statement. We whoare toptimistic believe this trend will accelerate at a-faster pace. Why? Because anyone engaged in the mining industry today can well afford to invest a minimum of $30,000.00 in capital equipment todisplace the labor of one man. This fact alone is a terrific incentive for mine management to apply and manufacturers to develop equipment of a type to get the men out of the mine. Now you can determine this problem not only becomes one of safety but also one of economics, When productivity is stepped up and manpower reduced management is learning the hard way what it means to them; in the profit and los s column when a few minutes of delay or downtime of costly machines and processes occur. They have learned that fast and efficient communication systems are the best means of combating breakdown, delays, bottlenecks, supply problems, the saving of lives and property and increasing production. One large western metal mine was able to increase Its tonnage by 4000 tons a day by using modernup to date electronic type communication system. The National Coal Board of Great Britain recently allocated 45,000,000.00 to study and develop faster and more efficient communications when a survey indicated what a serious bottleneck poor communication in their present systems of mining turned' out Lobe.

Jan 1, 1958

By H. Lyn Bourne

Daily everyone depends on the great variety of glass products, so much so that glass is often taken for granted. In fact most people do not realize how versatile glass has become. Consider the various uses and then try to imagine a day in which we are not influenced by glass. Common uses include container ware, table ware, window glass, lead crystal, automobile glass, and fiber glass. Several less common, but important, uses include laboratory ware, pharmaceutical, TV bulbs, light bulbs, glass ceramics, optical glass, fiber optics, and laser glass. Corning, Inc., a leader in specialty products, uses nearly 1 000 different compositions to manufacture about 60 000 different products (Edwards and Copley, 1977). Glass is such a complex product that-definitions vary and exceptions can be found for most definitions. Glass is an inorganic amorphous (non-crystalline) solid. Most glasses are produced by melting of a mixture of oxide raw materials, and then cooled to room temperature. Soda-lime-silica composition.s account for about 90% of all glasses melted (Anon, 1973). The properties of the glass product come mainly from its chemical composition. All of the different glasses require melting a combination of raw materials and forming the molten material into the desired shape. Both the melting and the forming processes use sophisticated technology and these technologies require experts to manage these production systems. The manufacturing process is continuous and takes place in tonnage quantities, so adjustments in the batch to achieve the desired finished product requires a great deal of expertise. Raw materials are fed to the batch mixing area in very large quantities (tons in most cases). As a result, impurities in the range of 0.1% result in addition of that impurity within the molten glass in kilogram amounts. More than twenty different industrial minerals are consumed in the manufacture of various kinds of glass (O'Driscoll, 1990). This chapter describes the major and minor ingredients of the various glass batches. It discusses the roles of the various oxides in the glass batch and most importantly considers the mineral raw materials which supply the glass industry. Each of the raw materials is described in detail in other chapters so the geology and mineralogy sections are kept brief here. Container glass, by far, accounts for the most production; followed by flat glass, fiber glass, and specialty glass of which table ware accounts for the greatest tonnage. [Table 1] shows the general production data for 1987 through 1990. Statistics for many of the uses do not appear because production volumes are small compared to the major uses. The glass industry is organized in four categories: containers, flat glass, fiber glass and specialty glass. The US Department of Commerce, Bureau of Census, publishes production data about the glass industry in three different categories: 1) glass containers, 2) consumer, scientific, technical and industrial glassware, and 3) flat glass. The Bureau has very complete statistics about the glass industry in these three categories but they report production data in different units according to industry standards. Therefore, [Table 1] gives the production data in dissimilar units. The production of most glass articles follows similar steps. The raw materials are mixed and the resulting batch is fed into the furnace. In soda-lime-silica glasses melting begins between 600 and 900°C. At these temperatures CO, and other gasses are released which create bubbles in the molten glass. To remove the bubbles and insure complete melting the temperature is raised to between 1 500 and 1 600°C. This is the melting-refining stage during which the refining agents in the glass batch serve to aid in the release of gas bubbles, homogenize the melt, and prevent the formation of scum on the surface of the molten liquid. At the conclusion of the melting-refining stage the glass is too fluid for working and the melt is cooled to about 1 100°C to attain the proper viscosity for working and forming to begin. After the glass article has been made, it must undergo annealing (slowly and uniformly reheated and cooled) to remove thermal stresses that were created during the forming process.

Jan 1, 1994

By V. B. Achanti, A. W. Khair

Introduction Laboratory studies were carried out at West Virginia University to investigate the rock-fragmentation mechanism of continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be bit spacing, bit geometry, depth of cut and cutting-drum rotational speed. This paper presents a discussion of the effects of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation. The removal of rock ridges/walls between adjacent grooves is analyzed with three hits mounted simultaneously on the cutting head, while the bit tip angle was varied from 600 to 900. Bit spacing was varied from 25.4 to 50.8 mm (1 to 2 in.) while the cutting process was assessed for varying cutting depths. Respirable dusts generated during the course of the experiments were analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism of continuous miners in terms of energy consumption and dust generation. A review of the literature revealed that a considerable amount of research has been carried out on rockcutting processes. Many authors agree that the mechanical cutting efficiencies of mining machines (e.g., continuous miners, shearers and road headers) are affected by a host of parameters. Some of these parameters are machine controlled, some are operator controlled, while others are uncontrollable. Efforts were focused on understanding the influence of parameters such as bit spacing, cutting depth, attack angle, bit type, drum speed, bit geometry (i.e., tip size, shape and tip angle) and rock type on the cutting process efficiency in terms of specific energy consumption and respirable dust generation (Strehig?? et al., 1975, Hanson et al., 1979, Khair et al., 1989). Roepke et al. (1976) in an attempt to study the dust and energy generated during coal cutting using point attack bits found that the dust and the specific energy consumed both decrease as the depth of cut increases. The four fundamental stages of dust generation luring rock fragmentation are identified by Zipf and Bieniawski (1989). Coal breakage by various types of wedges was assessed by Evans and Pomeroy (1966) in an extensive experimental study on British coals. Yet the industry today requires further attention and guidance to optimize the energy consumption and dust generation during the rockbreakage process. This paper attempts to give a better understanding of the influence of some of the parameters listed above and focuses on further improvement in the rock-cutting process. The specific energy consumed for different types of bits used and the respirable dust generated are analyzed in the context of the variation of a few other parameters. Laboratory investigation The experiments were performed in the Rock Mechanics Laboratories located at West Virginia University. A rock-cutting simulator designed and fabricated by Khair (1984) was utilized for this purpose. The details of this machine are available in the literature (see Khair 1984). For this study, a series of preliminary experiments was carried out to determine the optimum cutting frame advance speed. This was intended to facilitate a maximum cut depth of 31.75 mm (1.25 in.) at an advance rate of 0.525 mm/s (0.0207 ips) for all types of bits being used and various bit spacings being considered. To look into the cutting-process efficiency of a continuous miner in the laboratory, several parameters of influence are being considered. Besides the bit-geometry parameters, machine- and operator-controlled parameters, such as spacing of bits on the cutting head, the cutting head rotational speed and the total cutting depth during an experiment, are varied. At the time this paper was written, only part of the completed experiments were ana¬lyzed, and a number of experiments were still being carried out following an orthogonal fractional factorial experimental plan to assess the effect of all of the above¬mentioned parameters on the cutting efficiency in terms of energy consumption and dust generation. Three different types of tip angles, namely, 60°, 75° and 90°, and two different tip sizes, namely, diameters of 7.94 and 24.61 mm (0.313 and 0.969 in.), were used. At

Jan 1, 1999

By Theodore M. Gurr, James J. Bartels

Phosphate produced fertilizers provide the phosphorous nutrients required by plant life to sustain significant growth, thus improving the production of food for the world's population. Phosphorous replenishment of soil currently can be obtained efficiently by no other means than by direct application of phosphate fertilizer to the soil. Phosphate products are also utilized in animal feeds, detergent, and various industrial processes. Thirty-three countries are presently mining phosphate rock for the production of fertilizers, and its process byproducts. The major phosphate rock producers are the United States, the former Soviet Union, Morocco, and China [(Table 1)]. Phosphate rock is generally defined as a rock material that contains phosphate minerals which are sufficient for commercial usage. Phosphate minerals are found in sedimentary igneous and metamorphic rocks. Economic resources of phosphates are primarily developed from sedimentary rock sources. The apatite mineral family comprises the majority of phosphate constituents from both sedimentary and igneous rocks. Igneous phosphate rocks are generally composed of fluroapatite whereas sedimentary rocks are generally composed of carbonate fluroapatite, or chlorapatite. Phosphate rock is mined by a multitude of processes, including surface and underground mining. The mined rock requires mechanical and chemical processing to liberate the phosphate for utilization as fertilizer. Approximately 85% of the world's phosphate production uses sulfuric acid, with the remaining processes utilizing nitric and phosphoric acids. Ammonia is also introduced in the manufacture of liquid fertilizer, ammonium phosphate and ammonium polyphosphate. GEOLOGY Mineralogy and Chemical Properties Phosphate most commonly is derived from the mineral apatite, which is chemically described as CA5(F,Cl,OH)(PO4)3. Apatite is also broken up into the composite apatite minerals which are fluroapatite Ca5F(PO4)3, chlorapatite Ca5Cl (PO4)3 and hydroxyl-apatite Ca5(OH)(PO4)3. Carbonate CO3 can substitute for PO, forming carbonate apatite, called francolite. The guano phosphate (bird excrement) mineralogy commonly occurs as brushite CaHP04.2H20, monetite CaHPO4, whitlockite Ca3(PO4), and dahlite Ca10(PO4)6(OH)2. Apatite minerals form from igneous sources where they are developed deep in the earth's crust; and the cooling processes are slow, producing long, hexagonal prismatic to tabular crystals. The termination of the crystal can be basal plans or pyramids. In some instances, the crystals are bipyramids. Faster cooling, or sedimentary derived apatites are more commonly cryptocrystalline. Collophane is a name given to cryptocrystalline apatite found in phosphate rock in fossil form. Apatite minerals are relatively soft and are used to describe the 5 hardness on the Mohs scale. Cleavage is poor and develops along the C(0001). The color of apatite minerals varies from colorless, to violet, and blue, but are predominantly green or brown; luster is vitreous to subresinous. Collophane's physical appearance is often opaline, dense, with colloform structure and sometimes concretionary, nodular or pulverulent. Phosphate Bearing Materials Origins Phosphate deposits of igneous and metamorphic origins have been well defined. Sedimentary origins have been defined, but with a greater degree of uncertainty. Research in the 1980s proved out some of these processes through studies of real time deposition in Chile, Peru, and Australia. Igneous intrusive alkali rock and associated contact metamorphic rocks, provide approximately 20% of the world's phosphate. Fluorine containing apatite minerals are the most common materials containing phosphorous. Fluorapatite occurs in most igneous rocks. Fluorapatite and fluorine hydroxylapatite, together with carbonate varieties of these, are important members of the group. Where an essentially pure chlorapatite, carbonate apatite, and hydroxylapatite are rare and restricted in occurrence, the fluorine containing types occur in most all igneous rocks as early formed accessory mineral, usually in microscopic crystals, and may occur as extremely large bodies as magmatic segregations from alkalic igneous rocks. Apatite is also found crystallized in pegmatitic faces of both acidic and basic types of igneous rocks. More specifically, apatite is associated with magnetite deposits, in hydrothermal veins, especially those formed at relatively high temperatures, and in veins of the Alpine type. Apatite is common in both regionally and contact metamorphosed rocks, especially in the crystalline limestones where it is associated with sphene, zircon, pyroxine amphibole, spinel vesuvianite, phlogopite, talc, chloride schists, and as a contact metamorphic mineral.

Jan 1, 1994

By P. K. Hopke, A. Hubbard, K. H. Leong, J. J. Stukel, K. Nourmohammadi

INTRODUCTION In order to understand the transport and deposition of radon daughters in mine atmospheres, it is necessary to know the variation in the attachment of the daughter atoms to particles as a function of particle size, composition, number density, relative humidity, temperature, and radon concentration, the free gaseous diffusion coefficients of the daughters, and the variation in the mass transfer of the activity, both free and attached to particles, to mine surfaces as a function of particle size distribution, surface roughness of the mine walls, and the flow conditions. If all of these parameters are known in a model system, it should be possible to understand the transport and fate of the airborne radioactivity in real mines under certain well-defined flow conditions. There have been a number of recent investigations of the attachment of radon decay products to particles 1-4, but there are still a number of unanswered questions regarding the process. However, it is clear that for most real mine atmospheres, the vast majority of the activity is attached to particles. The size distributions for the activity-bearing airborne particles have been studied 5,6, and it has been found that most of the activity resides on particles with diameters in the range of 0.05 µm to 0.3 µm with an average mass median diameter between 0.1 and 0.2 µm. The behavior of the unattached radon daughter species has also been recently studied[ 7], and many of the previous problems regarding the value of the diffusion coefficient for Po-218 have been resolved. A major problem in the understanding of the airborne transport of radioactivity in mines is the lack of detailed knowledge of mass tranfer to and fluid flow over rough walls under fully developed turbulent flow conditions. This paper will report the progress on a project that is designed to obtained that information. MATHEMATICAL MODEL DEVELOPMENT Deposition of particles on smooth surfaces in turbulent flow has been extensively studied. A comprehensive review of these results has been prepared by Sehmel 8. There has not been such a comprehensive study of particle deposition on rough walls under such flow conditions. In recent years, only a single model has been proposed to explain such deposition 9,10 and in both of these papers the flow structure in the rough walled pipe was not taken fully into account. As part of the work being conducted on this project, a more complete model was outlined in a previous report [11]. The basic theory will be reviewed to provide a context for the flow measurements to be reported. The flux of particle deposited on the walls of a pipe in a turbulent flow is derived from the one dimensional form of Fick's law as given by [N = Dpdpp/dr (1) where N is the flux of particles deposited per unit area per unit time, D is the total eddy diffusivity of the particles, p is the airborne concentration of particles, and pr is the distance measured from the center of the pipe. The rate of deposition is best expressed by a deposition velocity Vp = NIP pb (2) where P b is the mean particle concentration in the sulk flow. The shear radius, V/ut and the shear velocity, u , are used to calculate a nondimensional distance, and velocity, respectively, where v is the kinematic viscosity of the fluid. The nondimensional form of equation 1 is given by Vd = DP dpp(3) V dr+ where Pp = Pp/ Ppb(4) By integrating equation 3 from the rough wall stopping distance, S , to the center of the pipe, the deposition velocity can be obtained. In order to make this calculation, it is necessary to have accurate descriptions for the particle eddy diffusivity, stopping distance, and shear velocity in order to insure that the influence of the flow structure has been properly accounted for. The shear velocity can be determined experimentally from the shear stress evaluated at the wall, Tw, and the fluid density, ut =VT w/p = ub V f/2 (5) where ub is the mean bulk axial velocity. The wall shear stress for a given pressure drop, dP/dL, and hydraulic diameter, Dh, is]

Jan 1, 1981

By Basil S. Fee

INTRODUCTION Probably the most important family of chemicals used in mineral processing today is a category of basic commodity chemicals loosely denoted as pH regulators. Typical chemicals which are referred to as pH regulators include lime, magnesium hydroxide, soda ash, caustic soda, ammonia, sulfuric acid, and hydrochloric acid. These chemicals are often used in very significant amounts in almost all of the major mineral processing operations such as flotation, hydrometallurgy, etc. (in dosages up to ten pounds per ton of feed ore treated). While cheaper in cost per unit weight of chemical than more specific chemicals such as collectors, frothers, extractents, etc., the overall cost to the mill operator is generally higher with pH regulators per ton of ore processed than with any other given processing chemical. For example, a rough rule of thumb in sulfide mineral flotation is that the cost of lime is double that of the collector(s) used. The symbol pH is used to designate hydrogen ion concentration. When acids, salts, and bases are dissolved in water, individual molecules are dissociated into their constituent radicals or ions. The strength of an acid or a base increases with the extent of such dissociation or ionization. An alkaline solution is one in which the number of Qydroxyl ions (OH ) exceeds the hydrogen ions (H ). In an acid solution, the hydrogen ions predominate. In either case, both ions are always present as water itself ionizes to a limited extent, that is: [ ] The pH scale is logarithmic and the pH value is the negative of the logarithm (base 10) of the molar concentration of hydrogen ions per liter of solution. For example, a pH of 5 means that the molar concentration of hydrogen ions per liter is 0.00001 (1 x 10-5). Likewise, a pH of 9 means that the molar concentration of hydrogen ions per liter is 1 x 10-9. Normally, the relationship between hydrogen ion and hydroxyl ion concentration is based on the relationship: Concentration of H ion x concentration of OH- ion = constant. Eq. (1) In dilute and/or moderately concentrated solutions that are normally used in mineral procygsing processes, the constant at 25°C is 10-14. On the pH scale, the value of pH equal to 7 represents the hydrogen ion concentration of a neutral solution. pH values lower than pH 7 indicate increasing acidity and higher values than 7 indicate alkalinity. Table 1 shows the nature of the pH scale at 25°C. Temperature affects the extent of ionization of dissolved acids, salts, bases, and water so that the hydrogen ion concentration (hence pH) of a solution is also affected by temperature. As a means of demonstrating this dependency, Table 2 shows the change of the exponent of the constant (base 10) in Eq. 1 and the pH value corresponding to neutrality as a function of temperature. It is also important, for example, that alkalinity or acidity expressed by pH not be confused with total alkalinity or total acidity. For example, total alkalinity is commonly determined by titration with a standard acid solution (usually HC1). pH is a measure of the hydroxyl ion concentration of an alkaline solution, whereas titration is a measure of an alkaline solution's acid neutralizing capacity. Thus, if one takes a series of various alkaline solutions prepared using different chemicals but all of exactly the same pH (and temperature) and then subsequently carries out a titration on each solution with a standard acid, it would be observed that the various alkaline solutions would neutralize entirely different amounts of acid. As an example, 0.08 grams of caustic (NaOH) , 6.32 grams of soda ash (Na2CO3), and 8.17 grams of ammonium hydroxide (NH4OH) all have a pH of 11.3 at 25°C. One liter of each of the above solutions neutralizes 0.073, 4.348 and 8.496 grams of HC1, respectively. Therefore, depending on the specific use of any given pH regulator, special tests need to be run by the mill operator to determine factors such as: the specific technical goals to be accomplished by

Jan 1, 1986

By Peter J. Huck, Yoginder P. Chugh, M. Jennings

INTRODUCTION Large areas of the United States coal reserves have been undermined by room-and-pillar mining over the past century. These abandoned mines generally cause subsidence of the ground surface many decades after mining. Reports from England (1) where there is a longer history of room-and-pillar mining indicate that mines abandoned two centuries ago may still be causing subsidence, and causing surface destruction to urban areas or farm lands that have been developed in the interim. The devastation wrought by subsidence, both in terms of property loss and societal disruption is enormous. The authors discuss here the methods by which subsidence in abandoned mines may be controlled. Two distinctly different subsidence control technologies have been developed in the U.S. for abandoned coal mines. These are referred to as (1) Point Sup- port methods, and (2) Areal Backfilling. As the names imply, point support methods are used to protect individual structures, or even individual foundation elements of structures, whereas areas backfilling techniques may be applied to protect entire neighborhoods or urban districts hundreds of acres in extent. Both point support methods and areal backfilling have specific sub-categories of techniques that may be applied under different conditions as appropriate. POINT SUPPORT METHODS Point support methods are characteristically employed by civil engineers chartered with the design of a new structure or the protection of an existing structure. The subsidence control measures are only a part of a larger project, the safety of which must be assured to a degree of near certainty. The costs of point support methods involve a large number of bore-holes and the use of expensive materials in relatively small quantities. There exist several dozen point support methods, which operate either to support the underground cavities, controlling subsidence, or to isolate the structure from the effects of subsidence if it should occur. The latter methods usually involve deep foundations through the mine opening supporting the structure on the underlying strata. Our concern will be with the former method to support underground cavities to prevent subsidence. Gravel Columns and Associated Methods Gravel columns may be placed in the mine opening using the methods shown in [Figure 1]. Boreholes are drilled through the mine strata, and gravel poured down the borehole to form a pile on the mine floor. When the tip of the pile contacts the mine roof, it is rodded down to spread the pile, and permit additional gravel to be placed. The objective is to place as much gravel as possible in the mine opening, and to achieve firm contact with the mine roof. The gravel pile acts to reduce subsidence by three mechanisms. The filling of a significant fraction of the open mine volume reduces the amount of potential subsidence simply by killing open volume within the mine. In effect, the extraction ratio has been reduced by introducing the volume of gravel. The toe of the gravel pile abuts against nearby pillars, providing lateral support and protection against pillar deterioration. In effect, the height of the pillars has been slightly reduced by burying their lower portions. Finally, some direct support is provided to the roof strata, reducing the roof span and enhancing stability. The gravel column method may be used in a variety of applications, and with materials other than gravel. For example, gravel columns may be placed in a close line around the perimeter of the building to form a continuous gravel wall. The interior of the site may then be completely filled with sand, slurry or other material. Alternatively, a lean concrete may be used in place of gravel, so that the piles achieve significant structural capacity. The grout column, shown in [Figure 2], begins with the installation of a conventional gravel column which is placed around a grout pipe that extends through the borehole into the mine opening. When the gravel column is in place, portland cement grout is injected in stages. At each stage, sufficient grout is injected to fill the interstices in the gravel to build a column perhaps two meters in diameter and a meter tall. The group pipe is then raised one meter, and after the previously injected grout has set, the next stage of grout is injected. The process builds a column of grouted gravel to the

Jan 1, 1982

By G. T. Lineberry, W. J. Wiehagen

A paradigm shift As market economists, mine managers are interested in "staying in business" and even "prospering." Bottom-line results are the "order of the day." Concern for bottom-line results can invoke questions such as how much was produced, at what cost, and was anyone injured? While these questions will always carry everyday emphasis at the mine, they are fundamentally lacking in that they often appear, especially to lower levels of management and to the production worker, as pre-eminent concerns. Driven by market economics, many organizations have decentralized, outsourced, downsized, restructured and formed new coalitions. Investments in new technology and a concentration on productivity have been an essential part of these changes, contributing to improvements in both safety and efficiency. A reason for (and, perhaps a result of) these improvements has been the development of a highly experienced and flexible work force. This situation presents an interesting opportunity to modify a few paradigms about work life in general, and perhaps a few paradigms about how we invest in the miner, in particular. Studying these issues now night offer some interesting opportunities for the Future, as the foundations for the next generation of mine workers are laid. With the average "experienced" U.S. miner five to fifteen years from retirement, perhaps a key determinant of future success in the world market might be how well we make the transition from today's work force to the work force of tomorrow. We can ill afford to wait a few more years to tap into the special knowledge residing within a veteran mining work Force. The Work Crew Performance Model (WCPM) is one approach to defining, capturing and transferring this expertise. The WCPM suggests a paradigm shift, moving from a focus on products (quantity) to a focus on the process (quality). It also involves a slight change in the process -- a different way to think and work. Of great importance, it entails a belief and a commitment to people within the organization; a commitment to collect simple (but interesting) data; exploration for insightful ways to plot and integrate that data; and finally the search for creative methods to reinvest that knowledge back into the organization, that is, back into the work force. As a way of thinking, the WCPM subordinates information about how much is produced daily or how many were injured over a year's time to concern and detail for how the individual's and the work crew's performance contribute toward meeting organizational goals. Drawing upon the expertise within members of that work crew to address and solve operational problems is one approach for meeting organizational goals. This everyday focus on how we work is hypothesized by the WCPM to make the difference between a good section supervisor and the average one; an exemplar continuous-miner operator and the run-of-the-mill one; a mining crew that produces consistently high quantities, but, inadvertently, degrades the production of other units. The WCPM permits objective and reliable performance data to be collected. This data then can be used to define variability within tasks of work crew members; to relate observed variability to a cost consequence; and to more meaningfully analyze performance through the integration of traditional analytical tools, such as the production simulator, CONSIM, with a recommended behavioral approach, the WCPM. Basis for engineering test Most equipment selections and purchases involve a field trial test of the system. Technology is routinely bench tested at the manufacturer's facility, government agencies and the mine site. The WCPM suggests a similar, but more practical, method for testing the performance of a work system -a test for how technology is used (by people) at the work site. It implies learning from veteran mining personnel that have gone well "beyond the book." This approach to learning and to integrating training with everyday work life can help answer questions such as: What constitutes desirable perfor¬mance as, for examples, a shuttle-car operator, a miner operator or a bulldozer operator; what characterizes exem¬plary performance within the context of the work system, the technology and the work crew; how can investments in the worker he linked to measurable results within the organiza¬tion? This paper explores these questions and makes recom¬mendations for enhancing the cost-linkages between invest¬ments in people and the mine's monthly cost sheets.

Jan 1, 1996

By D. Akers, R. Dospoy

Introduction The geological processes that form coal can also concentrate trace elements in the coal. For example, the average concentration of arsenic in bituminous coal (20 ppm) is ten times the average concentration found in all the other rocks that make up the earth's crust (2 ppm). Similarly, other elements, such as antimony, cadmium, mercury and selenium, are more concentrated in coal than in the earth's crust. When coal is burned, trace elements can be further concentrated. Although no new constraints on trace clement emissions were placed on the power generation industry under the 1990 Clean Air Act Amendments, the act does mandate a three-year study of air toxics. Any new regulations aimed at electric utilities as a result of this Federally-mandated study will almost assuredly be very costly-an estimated $1 billion per year. Many trace elements in coal are associated with mineral matter. For example, arsenic is commonly associated with pyrite, cadmium with sphalerite, chromium with clay minerals, mercury with pyrite and cinnabar, nickel with millerite, pyrite and other sulfides, and selenium with lead selenide, pyrite and other sulfides (Finkelman, 1980). There are also cases in which some of these elements are organically bound. Just as both organic and pyritic sulfur can be found in the same coal, the same trace element may be both organically bound and present as part of a mineral in the sane coal. Physical coal cleaning techniques are effective in removing mineral matter from coal and can potentially remove at least some of the trace elements associated with specific minerals, thereby reducing the release of these elements into the atmosphere. Conventional coal cleaning to remove trace elements As part of a project funded by the Electric Power Research Institute, CQ Inc., a wholly-owned EPRI subsidiary located in western Pennsylvania, has demonstrated that large reductions in the concentration of many trace elements are possible if conventional coal cleaning techniques are properly applied. Four examples are given in Tables 1 to 4. In each example, the results shown were generated by cleaning the coal at CQ Inc.'s commercial-scale cleaning test facility. Cleaning results for Upper Freeport Seam coal from Northern Appalachia are provided in Table 1. Data are presented in the table in two ways: as a weight-based concentration (parts per million) and as a concentration per heat unit (grams per billion Btu). Grams per billion Btu is analogous to pounds per million Btu, but avoids the use of numbers with many decimal places. The heat-based concentration provides a better measure of boiler impacts, because the increased heating value obtained through coal cleaning reduces the number of tons that must be burned to produce a given thermal output. Reducing the quantity of coal burned reduces the quantity of trace elements entering the boiler. This raw coal is relatively high in several trace elements of environmental concern, including arsenic, cadmium and chromium. Cleaning provided large reductions in the quantity of arsenic, barium, cadmium, chromium, fluorine, lead, mercury, nickel, silver and zinc. The results for tests with a Powder River Basin coal, Rosebud/McKay, are presented in Table 2. Large reductions in arsenic, barium, cadmium, fluorine, mercury, nickel, selenium and zinc were observed with cleaning. The concentration of chromium increased with cleaning, while lead concentration increased in one test and decreased in another. Table 3 presents test results for Croweburg Seam coal from Oklahoma. Large reductions in arsenic, barium, cadmium, chromium and zinc were obtained with cleaning. Smaller reductions were obtained with lead and nickel, while chromium, fluorine and mercury increased in at least one of the tests. Table 4 presents cleaning test data for Kentucky No.11 Seam coal. In this case, large reductions were obtained with all elements measured. In general, these data indicate that physical coal cleaning is effective in reducing the concentration of many trace elements, especially if they are present in the coal at relatively high concentrations. The degree of reduction achieved is coal-specific, relating in part to the degree of mineral association of the specific trace element and the degree of liberation of the trace element-bearing mineral. The extent of trace element removal also depends on the method of cleaning the coal. Figure 1 is a washability plot, by size fraction, of arsenic vs. ash content for Upper Freeport

Jan 1, 1994

By Jozef S. Stachulak

Inco Limited operates 11 underground mines in the Sudbury District. The mines are located on the rim of the Sudbury Basin, an oval with the axis in the range of 27 and 60 km. The ore dips to at least 3000 m below surface. The ores are mined primarily for nickel and copper. Total ore production from underground is in excess of 55,000 tons per day. Over 40 surface fans have been installed since the late 1960's. All of the fans are adjustable pitch, axial flow units. A major factor influencing ventilation design in the last 30 years has been the introduction of diesel equipment underground. Volumes per fan have ranged from 60 to 330 (cubic metres per second), with motors from 100 to 2500 hp. Fans of the axial flow type have been in common use for main fan installations at Canadian mines for many years. The standard arrangement has been to mount these fans horizontally, i.e. with the fan shaft and the long axis of the housing horizontal. This is a natural arrangement for an underground fan, but for a surface installation, a vertically mounted fan has definite advantages. The surface area taken up by a typical vertical fan installation is generally about one quarter of that with a horizontal fan of the same capacity. (1) This is not a problem with isolated fans and flat surface outcrop sites, but where the installation is to be near existing buildings, or where there are poor surface soil conditions, space and cost considerations greatly favour vertical fans. MAIN FANS INSTALLED There are 43 main surface fans in operation at 11 mines. Twenty-seven of these fans are supply units, and 75% of them are vertical installation. The remaining 16 units are main surface exhaust fans, with predominantly horizontal installation. Within the last five years, some 20 main booster fans have been installed underground at several mines. Axial flow fans, with adjustable pitch blades, are used for both surface and underground installations. Exhaust fans are equipped with stainless steel or cast aluminum blades. Main underground fans are arranged horizontally and the majority of them have a floating shaft between the fan shaft and the motor. (2) The size of the fans in service varies from 1.8 m to 5 m in diameter, with the majority ranging from 1.8 to 2.5 m. The pressure produced by these fans varies from 0.25 kPa to 2.0 kPa. At Inco Limited, two main fans in parallel are preferred, rather than a single fan, so that if one fan fails, the remaining fan can still supply up to 70% of normal air quantities, while the damaged fan is repaired. This requires closure doors on each of the fans so the fan can be isolated in case of failure. It is more expensive than a single fan, but results in less production interruptions. The fan installations are well away from sharp inlet and outlet bends. FAN DESIGN INTEGRITY Both the mine operator and the fan manufacturer must understand that the main fan is critical to the mine operation, and that everything technically possible must be done in design and manufacture to ensure the highest degree of reliability. Some of the design parameters and criteria, based on Inco experience, are outlined and discussed below. RESONANT FREQUENCIES AND HOUSING MODEL ANALYSIS Any fan assembly will have many different resonant frequencies. It is a challenge to the designer to arrive at a design in which forcing frequencies do not coincide with any of these resonant frequencies to produce unacceptable vibration levels in operation. Finite element analysis is a useful tool that can be used to identify the most critical of these, so that housing and blade stiffness can be adjusted to change any resonances that might be close to forcing frequencies. Shaft critical speeds should be at least 25% above the fan operating speed, and there should be sufficient separation between other resonant and forcing frequencies to avoid excitation that might result in high vibration levels. QUALITY ASSURANCE Radiographic Blade Examination Mine fan blades are normally cast in small lots. To ensure that the castings are sound, a full radiographic examination is recommended in the highly stressed lower 1/3 of the blade.

Jan 1, 1995

By R. Edward Williams

The Spa1lation Process Because of the low thermal conductivity of many hard rocks, rapid heating of these rocks produces a thin surface layer in which the temperatures attain high values. Thermal expansion of this surface layer is constrained by the reminder of the still cool rock, and when stresses within the surface rock become high enough, the surface rock breaks away from the cooler rock behind it and flies or falls off as a thin flake called a spall. Then the next, newly exposed surface is heated, and the process continues. This process is the basis of spallation drilling. The hot gases from a jet burner provide the heat for spallation to occur, and their high velocity provides a scouring action that transfers heat to the rock and removes the spalls as rapidly as they form. Spallation is a process which works in very hard rock. It is dependent upon the thermal expansion coefficient and the thermal diffusivity of the rock but is also affected by any discontinuities in the rock. To date the efforts which have been made to evaluate the various rock according to their spallability has been minimal. As the success of this process is dependent upon the characteristics of rock it is expected that the study of rock mechanics will prove to be of greater value to this program than to the other mechanism for drilling and excavating rock. Commercial Uses of SPALLATION In the 19408s, the Linde Air Products Division of Union Carbide (UC 1 began developing spallation for use in mining taconite ore, which is presently the chief source of iron in the United States. In this work UC developed a jet-piercing tool that burned fuel oil with oxygen to produce spallation and contained mechanical cutters to remove rock that was not amenable to spallation. The UC jet-piercing machines have since produced about 40 million feet of shallow blast holes used for emplacing explosives in the taconite mines. During this work it was found that hole diameters could be increased by merely reducing the advance rate of the burners and that existing holes could be enlarged by making another pass through the hole with the same burner. The Browning Engineering Go. of Hanover, N.H., has developed a hand-held spallation burner to cut slots in granite. It has been used for a quarter of a century and is now standard equipment for quarrying granite throughout the world. This burner, which resembles a small jet engine oriented with its exhaust pointed downward, is the forerunner of a flame jet burner used to spall experimental holes in granite at maximum rates in excess of 100 ft/hr when operating in hard, competent granite. It uses No. 2 fuel oil, which is burned with compressed air. The system uses water to cool the burner and the exhaust gases. These gases, along with the steam produced from the cooling water, blow the spalls from the hole. Experimental Work Theoretical and experimental work has been accomplished by the Massachusetts Institute of Technology and the Los Alamos National Laboratory. This work is reported in Refs. (3) and (4). To verify the experimental results of this work laboratory scaled down field tests were conducted using two we1 1 characterized granites from quarries in Barre, VT and Westerby, RI, under defined heating conditions. In the laboratory tests a propane - oxygen heating torch was used to direct a flame at the granite surface and the spal 1 ing process was examined at various heating rates with a high-speed video taping system operated at 200 frame per second. This produced a time-lapse sequence where the onset of the spallation process was easily distinguished. Also the heat flux from the torch to a flat surface at various stand off distances and flows was measured. A similar set of tests was conducted using the more easily quantified and uniform heat source of a 1.5 kw GO2 laser. This allowed accurate

Jan 1, 1986

By LeEtta M. Shaffner, John R. Marks

INTRODUCTION In the last twelve years, underground stoping methods at the Homestake Gold Mine have evolved from open cut-and-fill with jacklegs, cribbed raises and electric slushers to ramp-based mechanized cut-and-fill (MCF) and vertical crater retreat (VCR) with dieselpowered loaders, trucks and drill jumbos. The evolution was swift. Unfortunately, ventilation practices have had trouble keeping pace. Stope ventilation is still too dependent on auxiliary fans and coolers. A single large MCF stope might contain up to eight headings, each of which requires significant ventilation resources when a diesel loader is present. Air is shortcircuited all too frequently through mined-out VCR panels. These factors and the recent rapid decent of the center of mining prompted a study to improve ventilation practices and to more accurately project future requirements. BACKGROUND In 1992, the underground portion of the Homestake Gold Mine produced 8336 kg of gold from 1407 ktons of ore (268,000 oz from 1,551,000 st). The ore is hosted in low to medium grade meta-sediments. Stoping took place from 420 to 2347 m below the surface (1400 to 7700-ft levels). The weighted center of mining was 1662 m deep (5450-ft level) in 1990 and is projected to be 1890 m (6200-ft) in 1993. The deepest level is 2440 m (8000-ft) where the virgin rock temperature (VRT) is 56.1°C (133F). The mine is ventilated by 504 m3/s (1,069,000 cfm) measured at mid-exhaust-circuit density. The air-conditioning system includes an 8.1 MWR (2300 ton) controlled recirculation plant, a 2.0 MWR (580 ton) chilled water plant, a 1.0 MWR (290 ton) exploration drift refrigeration plant, 28 spot-coolers totaling 3.4 MWR (960 tons) and 35 spray coolers totaling 1.5 MWR (420 tons). The mine employs 117 diesel units with a total nameplate rating of 7961 kW (10,672 hp). These units include twenty-four 1.5m3 (2-yd) loaders, twenty-six 2.7m3 (3.5-yd) loaders, fourteen 3.8m3 (5-yd) and two 7.6m3 (10-yd) trucks, and assorted utility vehicles and drill jumbos. THE STUDY In April 1991, the University of Nevada-Reno (Mackay School of Mines) and the South Dakota School of Mines and Technology cooperated with Homestake on an MCF study. Mackay instrumented a stope with thermocouples, air velocity meters and hygrometers (Duckworth, 1992). South Dakota Tech conducted a finite-elements computer analysis of a back-filled MCF stope with/without light-weight shotcrete insulation on the sidewalls and back (Chellam, 1992). Homestake conducted an empirical analysis of deep-level MCF stoping. This paper describes the Homestake study. Twenty-three of the forty MCF stopes deeper than 1800 m were surveyed at least once during the last quarter of 1992. The stopes not included were being cable-bolted or back-filled. Figure 1 shows the complexity of one of the ramp-based stoping areas included in the survey. This particular stope has six separate production headings. A baseline wallrock heat load was derived for each stope or heading from psychrometric calculations. Broken ore, waste rock fill and fissure water were noted when present and the effects included in the baseline heat load. Other heat sources often mentioned in the literature such as metabolic heat from workers, heat from explosives and small electric loads were neglected. Fan heat was considered part of the ramp & crosscut heat load and thus not included in the study. Diesel heat was addressed separately. RESULTS Survey results, plotted as the heat flux against VRT, are shown in Figure 2. The equation for the regression line is: W/m2 = 2.1236*VRT - 75.405 The 0.31 correlation coefficient is poor which implies that the results should be used cautiously. Previous experience strongly suggests that differences in productivity are most likely responsible for the scatter in data points. A rapidly advancing stope will have a

Jan 1, 1993

By Jonathan Ludlow, Robert A. Jankowksi

Introduction A longwall operator can make few changes to increase output, significantly reduce respirable dust, and decrease power consumption. Reducing drum speed, and thereby cutting with increased pick penetration, is one. This article defines the benefits of deep cutting in terms of reduced dust production and power consumption. It also identifies the practical aspects of high pick penetration in terms of shearer performance and coal loading. Before examining some practical aspects of reducing drum speed and looking at the theoretical background, it is worthwhile to summarize what is meant by high penetration and deep cutting, and what potential benefits and pitfalls may be expected. Deep cutting (in the sense of high penetration rather than wide web) can be defined in one or more of the following ways: • Cutting with an average pick penetration distance higher than that used in the past. • Cutting with a pick penetration higher than the longwall operator would have used if the advantages of deep and slow cutting were not considered. • Cutting with a well-designed shearer drum below 40 rpm. All these definitions are slightly arbitrary. They are given to provide a basis for discussion and to make the point that any move towards deeper, more efficient cutting can result in operational benefits. The benefits of deep cutting appear in many different areas. The most noticeable benefit, provided suitable instruments are available, is the reduction of airborne respirable dust. During an experiment on a longwall in the Pittsburgh seam, a nearly four to one reduction in dust levels was seen when drum speed was halved. Not all studies have shown such a big reduction, but it seems that some benefit is almost always obtained when drum speed is reduced. Production rate and specific power consumption are also affected (in a positive sense) by reducing drum speed or increasing pick penetration. Although these changes may not be as spectacular as those in dust level, they contribute to the economic return of the longwall operation. Similarly, improved washability through fines reduction may have a beneficial economic effect. Cutting with shearer drums operating at lower speeds does have some possible deleterious impacts that an operator should be aware of. For example, cutting reactions - loads imposed on the picks by the coal being cut - will be increased as a deeper cut is used. Steps must, therefore, be taken to ensure the stability of the shearer and provide an adequate haulage effort. These increased cutting reactions also result in higher loads on the power transmission system (gearboxes, ranging arms, pick boxes, etc.) from the shearer motor(s) to the pick tip. These higher loads must be anticipated and provided for with the necessary hardware. In particular, extra haulage power must be provided with low drum speeds, since haulage effort required increases roughly in proportion with pick penetration. Because the drum will be rotating more slowly or will have fewer picks, the load on shearer components will also be more variable. If suitable, robust equipment is not used, this increased vibration will decrease reliability. Benefits of Deep Cutting Lower dust levels, decreased specific power consumption, and improved product washability are the most noticeable benefits of reduced drum speeds. Although the benefits will vary greatly with mining conditions and the type of coal, some examples of what can be expected are described below. Reduced Dust Levels Figure 1 shows principal results of a study on the effects of reduced drum speed conducted on a longwall in the Pittsburgh seam (Ludlow, 1981). This figure shows that average dust production was reduced by about 70% when drum speed was halved. By making some assumptions about such quantities as coal density, it is possible to apply this proportional reduction to the quantity of respirable dust liberated per ton of coal mined. When this is done, two kinds of results are obtained: • At 70 rpm, about 1 g (15 gr) of airborne respirable dust is created for every ton mined (roughly one part per million). At 35 rpm, only 0.28-0.37 g/t (3.9-5.1 gr per st) of coal mined become airborne respirable dust. • At 35 rpm, nearly four times the amount of coal may be mined before the compliance level is exceeded, compared with 70 rpm.

Jan 3, 1984

By E. J. Garrison

Discussion by E.J. Garrison A.C. Noble presents a clear and concise summary of the factors pertinent to a competent reserve evaluation of a mineral occurrence. However, I believe that he confuses the difference between a resource and a reserve. By definition, a reserve estimate includes all known economic, legal, mining, metallurgical and environmental factors impacting the recovery of the product(s) found in the deposit. A resource estimate, however, is an estimate of what is there - what is available for exploitation and should not include economic and other considerations. Only after defining the resource, its extent, location, physical and chemical properties, can an intelligent selection process begin of the extraction and processing technologies most appropriate to the circumstances encountered. The early and almost certainly inappropriate application of these often cookbook choices has probably lead many companies to walk away from good properties. (How many mines have been found in others rejects?) An example of the process is the early selection of metallurgical samples, after encouraging values are found in a few holes or surface samples, in an attempt to determine the economics of the prospect. Unfortunately, the sampler does not know how representative of the occurrence the sample is because he does not know what the deposit looks like. As a consequence, the property becomes saddled with a bad metallurgical sample that is often inappropriately used in evaluating the deposit which it does not represent. Reply by A.C. Noble E.J. Garrison asserts that I confuse the difference between a resource and an ore reserve. In fact, this paper was motivated by the observation that resources and reserves are almost universally confused throughout the industry. While Garrison is concerned that too-early consideration of engineering, metallurgical and economic factors will result in dropping properties too soon, some issues that must be considered include: •The purpose of exploration is to discover ore reserves, not to discover resources. •Ore reserves are always smaller than resources. • Decisions on exploration expenditures must be made based on the expectation of the quantity of ore reserves that will ultimately be defined. Noble's Fig. 2 can be used to give guidance as to when it is appropriate to begin reserve calculations. When exploration enters the "flat" portion of the curve, representative samples can be selected for metallurgical studies and appropriate mining methods chosen. It is at this stage that we know enough about the deposit to make intelligent choices of representative samples and recognize constraints on mining caused by the deposits shape, environment and physical properties. Once the appropriate technologies have been chosen, then their cost can be estimated with reasonable accuracy. Early entry of economic and process factors gives the false appearance of reserve status to the resource estimation. It would be more informative and less subject to abuse and misunderstanding if resource calculations were made at a number of cutoff grades. The cutoff grades should be chosen to cover the range of grades found in practice in existing operations of similar type. This would emphasize the open nature of resource estimates and encourage creative evaluation of mining and process technologies. It does not preclude the use of economic, environmental and recovery technology factors in deciding the advisability of continuing exploration expenditures, but would highlight their speculative nature. It is thus hoped that decisions on the future of the deposit would not be made on the presumed suitability of a given technology but on the actually known reality. I agree that resource estimates should be reported as a range of cutoff grades. Since reporting at a cutoff implies application of underlying economics (even by analogy to similar properties), however, it should be clearly stated that resources do not consider economic, mining or cost factors, and that ore reserves will be substantially less. The dilemma of the explorationist is that until the continuity and limits of ore-grade mineralization have been established, it is difficult to make quantitative estimates of either resources or ore reserves. Further industry discussion is needed regarding standards for disclosing early exploration information in such a way as to fairly represent the potential of an exploration property.

Jan 1, 1995

By Dennis S. Kostick

Introduction Soda ash is known chemically as sodium carbonate, an important inorganic chemical. It has been produced for several centuries by processing certain vegetation and minerals. The US soda ash industry has evolved from several small sodium carbonate mining operations in the West. Now, a nucleus of six companies produce about one-fourth of the world's annual soda ash output US producers currently dominate the world market. But certain international events are occurring that will reshape the domestic soda ash industry in the next decade. Historical perspective Soda ash is used mainly in the manufacture of glass, soap, dyes and pigments, textiles, and other chemical preparations. All of these are the first basic consumer products produced by developing societies. About 3500 BC, the Egyptians became the first society to use crude soda ash. The soda ash was used to make glass containers. It was most likely obtained from dried mineral incrustations around alkaline lakes. Soda deposits were virtually nonexistent in western Europe. So people resorted to burning seaweed to obtain the ashes. The ashes were then leached with hot water and the solute was recovered after evaporating the solution to dryness. The solute, a crude "soda ash" was impure. But, it could be used to make glass and soap. These two products and industries were important to the population and economic growth of the region. About 11.5 t (13 st) of seaweed ash was required to produce about 0.9 t (1 st) of soda ash. Along the coasts of England, France, and Spain, seaweeds with varying alkali contents became important items of commerce and sources of soda ash before the 18th century. The LeBlanc process used salt, sulfuric acid, coal, and limestone. It became the major method of production from about 1823 to 1885. In the early 1860s, Ernest and Alfred Solvay, two Belgian brothers, successfully commercialized an ammonia-soda process to synthesize soda ash. It used salt, coke, limestone, and ammonia. The Solvay process produced a better quality product than the LeBlanc method. In 1879, Oswald J. Heinrich presented to the Baltimore meeting of AIME, a paper entitled "The manufacture of soda by the ammonia process." The paper compared the two processes and foretold the demise of the LeBlanc technique. World production of soda ash in 1880 was 680 kt (750,000 st). Of that, 544 kt (600,000 st) was produced by the LeBlanc process. Of the 2.8 Mt (3.1 million st) of soda ash produced worldwide in 1913, only about 50 kt (55,000 st) was by the LeBlanc method. The LeBlanc process was never used successfully in the US, except for a brief period from July 1884 to January 1885 in Laramie, WY. Previously, soda ash had been produced by burning certain plants, as exemplified by the early Jamestown colonists, or by recovering small quantities of natural sodium carbonate found in alkaline lakes, such as those found near Fallon, NV, and Independence Rock, WY. Before the 1884 startup of the first synthetic soda ash plant in the US at Syracuse, NY, most of the domestic soda ash demand in the East was met by imports, primarily from England. Large-scale commercial production of natural soda ash began in California in 1887 from surface crystalline material at Owens Lake. Production from sodium carbonate-bearing brines at Searles Lake began in 1927 (Fig. 1). In 1938, during exploration for oil and gas in southwestern Wyoming, a massive buried trona deposit, presumably the world's largest, was accidentally discovered. Recent mineral resource evaluation by the US Geological Survey and the US Bureau of Mines indicates that the Wyoming trona deposit contains 86 Gt (93 billion st) of identified trona resource in beds 1.2 m (4 ft) thick or greater. Additionally, there is about 61 Gt (67 billion st) of reserve base trona. Of this 36 Gt (40 billion st) is in halite-free trona beds and 24 Gt (27 billion st) is in mixed trona and halite beds. In 1953, the Food Machinery and Chemical Corp. (later shortened to FMC Corp.) became the first company to mine trona in Wyoming. Soda ash demand increased.

Jan 10, 1985