Search Documents

By Lok W. Home

HISTORICAL DEVELOPMENT At the beginning of the 1970 more than 90% of pro¬duction drilling in open-pit mining was obtained with the use of rotary drills. At the same time, the use of rotary drills underground was virtually nonexistent. Several progressive mines began questioning whether efficient rotary drilling could not be adapted to under¬ground applications. In the late 60s and early 70s at¬tempts to use rotary drilling were made by Inco, Ltd. and Meramac Mining, utilizing drill units designed as a combination of small diameter raise drills and rotary drills. These initial attempts were unsuccessful primarily due to the immobility of the equipment and low degree of dependability. At the same time, experiments con¬ducted by Inco and Meramac using large diameter in¬the-hole percussion drills produced immediate encourag¬ing results. The first serious attempt at utilizing rotary drilling underground was made by Texasgulf in 1971 at Kidd Creek mine in Canada. An experimental stope 15 m wide, 36 m long, and 30 m deep was drilled using 200-mm diam rotary drilled holes. The machine used was a Robbins' Model 11 D. The Model 11D is a rotary drill designed to drill drain and utility holes under¬ground. The results of this test revealed that large diameter blasthole stoping was feasible. The indications were that the major areas of concern-fragmentation and pillar damage-could be controlled and a new low-cost stoping method resulted. At this point Texasgulf and Robbins entered into a cost-sharing agreement to develop a rotary drilling unit specifically for this stoping method. Drilling of the trial stope required pouring a concrete pad at each drill hole plus anchoring the derrick to the pad by means of rock¬bolts. Utilization expressed in terms of drilling time to available time was less than 20%. It was obvious that the required unit had to be mobile, setup time had to be minimized, and rod handling had to be improved. The first attempt at an underground production-type rotary drill consisted of mounting the basic 11D on an air-powered Eimco 600 Series crawler. The crawler was equipped with four screw-type leveling jacks operated by an impact wrench; rod rack facilities for 60 m of 1.2-m long, 170-mm diam rods; a rod handling facility consisting of an air-lift swing boom and a pipe loader which automatically positioned the rod under the float¬ing drive box; a turnbuckle anchor system requiring in¬stallation of four rockbolts in the drill drift floor and placing turnbuckles from the rockbolts to the corners of the drill; and trailing power units containing the electrics and hydraulics required to operate the drilling unit. Operation of this unit revealed a vast improvement in drilling time but some problem areas remained. The anchoring system required secondary drilling and proved difficult to adapt to the localized irregular floor surface and the trailing power unit was difficult to maneuver and was causing unnecessary maintenance costs. Addi¬tional improvements resulted in the standard 11MD rotary blasthole drill. DESCRIPTION OF UNIT This standard model consists of the drill and the power unit integrally mounted on an air-powered crawler chassis (Fig. 1). The rod-handling and leveling¬jack systems are similar to those used on the prototype Texasgulf unit and remained relatively the same. The anchoring system has been replaced by the roof jack, initially screw type but now hydraulically actuated. The anchoring system is necessary as the drill exerts more thrust than the weight of the unit. During operation it is found that the two front jacks adequately anchor the machine. The complete unit's operational dimensions are: height, 3.2 m; width, 2.1 m; and length, 4.2 m requiring a 3.5- x 3-m drill drift. The derrick is pivot mounted and raised and lowered by a hydraulic cylinder reducing the transport height to 2.5 m. The derrick is also turnbuckle mounted to allow dip angle drilling from vertical to 0.52 rad (30°) off vertical. The drill derrick can be mounted to allow dip axis to be parallel or perpendicu¬lar to the long axis of the unit. The standard rods are 1.2 m in length and are contained in racks of 10 which can be removed for transportation. Drilling torque is produced by a 56-kW (75-hp) electric motor driving a double vane pump which in turn drives a Robbins high torque gear-type hydraulic mo¬tor. In addition to the hydraulic motor, the machine drive system has a 3.9:1 planetary gear reducer. This results in six speeds with the following minimum and maximum range: Maximum rpm 112 Torque 3725.5 J (380 kg m) Minimum rpm 10 Torque 14 706.0 J (1500 kg m) Drilling thrust is provided by two bootstrap cylin¬ders pressurized by a variable volume pump. This sys¬tem can produce from 0 to 267 231.2 N thrust in either direction. Bailing air (approximately 17 m3/min at 382.2 to 490.3 kPa) is introduced through a rotary swivel pass¬ing directly through the center of the drive system to keep efficiency and losses to a minimum. Hole annulus is also kept to a minimum by using 170-mm rod when drilling a 200-mm hole. A small amount of water is added to the air for dust suppression. The machine has to be supplied with air, water, and electrical power. It does not appear feasible to provide an integral air power supply with the rotary drill such as is done with open-pit rotary drills. Air is required and installed during the primary development of the drill drift. The machine can be adapted to drill hole diameters from 170 to 228 mm for blasthole operations. The drill string consists of the rotary bit, crossover stabilizer, roller stabilizers, and standard rods. The operator controls speed and thrust pressure from an operating console which can be mounted in a conve¬nient position. Mount Isa has made an adaption to the operating console to permit remote collaring of drill holes in an uncleared floor.

Jan 1, 1982

By Gerard P. Hand

The use of graphite in industrial applications is one of the oldest in the world. Yet, it is one of the fastest-changing technologies today. Graphite was first used centuries ago in developing writing instruments and as a raw material in crucibles used in melting metal. Today, graphite is used in some of our most demanding industries. These include aerospace, electronics and automotive applications. Graphite usage has historically been split between the natural and synthetic forms. Figure 1 shows the breakdown of natural graphites and synthetic graphites used. The usage of natural graphites and synthetic graphites is split fairly evenly, although the applications are quite different. Figure 2 shows the breakdown of applications using natural graphite. The largest application is the refractory industry. This includes refractory brick and plastics, crucibles, shrouds and other refractory parts. This main application uses roughly 50% of all natural graphite. The refractory industry is an important application for natural graphite. However, the refractory markets have been struggling for several years. As demonstrated in Fig. 3 (Semler, 1996), the production of refractories in tons per year has declined by more than 32% during the last 25 years. Refractory prices have actually risen on a dollar per ton basis during that same period as the product mix has shifted to the value-added side. Raw material and production cost increases, inflation and other related costs have kept profitability at low levels for the industry. Furnace linings that once lasted 1,000-2,000 heats now last 8,000-12,000 heats. This means that tonnage requirements have gone down and quality requirements have gone up for graphite suppliers. Therefore, new opportunities and applications must be developed if the graphite industry is to grow. Synthetics are the other major forms of graphite. There are two forms of synthetic material currently used. One is the traditional type. It is made from the turnings of graphite electrode production. The second was developed in the mid-1970s in response to a shortage of conventional synthetic graphite. This occurred by a breakthrough in thermal technology. This new technology purifies, desulfurizes and graphitizes petroleum coke on a continuous basis at temperatures of more than 2,500° C (4,532° F). This product is called desulfurized petroleum coke (Desulco). It now accounts for about half of the synthetic type material used in the United States. Figure 4 shows the breakdown in the use of synthetic types of material by application. The largest requirement is for use as a carbon addition in iron and steel. This is followed by alkaline batteries and friction materials. Current technological opportunities New opportunities for graphite products are now being developed. These new areas are made possible due to the advances in graphite thermal technology. The ability to purify and modify graphite and carbon products is the key to future growth in the graphite industry. New, higher-purity, more consistent graphite products are leading to enhanced performance in current applications. They are also opening the door to new applications.

Jan 1, 1997

By Ravi Shah, Augusto Lucarelli, Daniele Peila

"In mechanized tunneling the annular gap between the segmental lining and the surrounding soil caused by tunnel driving, must be backfilled almost instantaneously with an adequate grouting mortar. The objective of this research is to perform a fully three dimensional modeled parametric study using FLAC 3D and evaluate the effects of backfill grouting on the tunneling performance. The research focuses on comparisons between different injection materials and state-of-the-art Bi-Component grout and their effects on the settlements on the surface. The research consists of testing a regular situation of tunnel excavation using a shielded machine with face under pressure. The tunnel dimensions and the soil properties are selected as close as possible to the reality and based on Turin Metro case. 1 INTRODUCTION Excavation of tunnels in urban areas can induce ground movements, which have negative effects on existing structures. In such scenarios, shield tunneling has become a well-accepted construction method in various ground conditions. It is characterized by relatively complex interactions between the soil, the tunnel boring machine (TBM) itself, the tunnel lining and the tail void grout. The problem to control the settlement depends on the face pressure, ground properties and back filling procedure and material of the tail void. The face pressure acts against the front to guarantee the face stability. In case of EPB TBMs the stability of the tunnel face is ensured through the excavated soil itself, which is conditioned and is maintained in compressed state within the excavation chamber. When excavating with TBMs a tail void is created between ground and the lining (Fig.1) after the TBM excavation and ring assembly that must be backfilled instantaneously by injecting the backfill material through the TBM’s tail shield. The process is of primary importance as it reduces the surface settlements and creates an immediate link between the ground and lining, sealing against ground water and leakage, reducing the differential movements between segments and providing long-term stability. The most used backfilling materials are: Inert mixtures that do not contain cement instead sometimes they are replaced by fly ash or other substitutes. A typical design of an inert mortar consists of sand, fly ash, bentonite and water. Pea gravel, which is constituted of granular materials with grain size ranging from 8 to 12 mm. This mixture is highly recommended for tunnels being constructed in rock mass with little deformation rates.Cement mortar is composed of cement, water, aggregates and sometimes bentonite. Cement controls the principle mechanical property of the mix, which can reach high values of 15-20 MPa in 28 days. The aggregates contribute towards the shear strength and reduce the pumpablity of the mix (Thewes and Budach, 2009). The reduced active systems have a cement content of 50-100 kg/m3, whereas the active system the binder component derives full hydration with cement content of over 200 kg/m3 ."

Jan 1, 2016

By Michael L. Cramer, Kunsoo Kim

INTRODUCTION The Columbia River Basalt beneath the Hanford Site is one of several rock types being considered by the U.S. Department of Energy for the first commercial high-level nuclear waste repository. The Basalt Waste Isolation Project (BWIP) has been carrying out a comprehensive investigation to assess the feasibility of constructing a repository in basalt and to develop technology required for repository engineering and site characterization. Development of a nuclear waste repository requires a number of design considerations not usually necessary in the planning of conventional underground structures. Principal among these is the thermally induced stress field resulting from waste emplacement. This thermal stress, super- imposed on the preexisting in situ- and excavation- induced stress fields, needs to be evaluated in the design process due to the sensitivity of waste emplacement density to this factor. The nature of this thermally induced stress field is dependent on several factors, including the temperature distribution around the repository openings, the thermal properties of the rock mass, and the deformability of the rock mass. Re1iable performance of the repository structure is largely determined by the ability to under- stand the above rock mass characteristics and predict the underground opening response to waste emplacement based on this understanding. To gain an understanding of this rock mass behavior in a repository condition, the BWIP has conducted a large-scale heated block test in basalt at the Near-Surf ace Test Facility (NSTF) on the Hanford Site. This paper presents the results from the elevated temperature phase of the block test in which the thermal, mechanical, and thermo- mechanical response of the closely jointed basalt rock mass was evaluated as a function of stress and loading orientation at varying temperatures up to 200 oC. SITE GEOLOGY The NSTF test areas, including the block test site, are located in the entablature zone of the Pomona basalt f low. The Pomona flow entablature is structurally typical of most flows in the Columbia River Basalt Group in that it is characterized by long, undulating, polygonal columns up to 2.4 m in length. Columns vary from 15 to 30 cm in diameter, averaging about 20 cm. Over their length, columns can vary in dip by 150 to 200. The column structures are dissected by subhorizontal cross joints that are generally discontinuous and seldom cross columnar joint boundaries. Spacing of the cross joints also averages about 20 cm. A representative joint pattern taken from mapping of the tunnel wall near the block test site is shown in figure 1. Application of the Rock Mass Rating System (Bieniawski, l979) to the block test site yielded an overall value of 62. The corresponding value from application of the Q-system (Barton et al., 1974) is 8.7 (Cramer and Kim,1985). The NSTF is approximately 50 m below the surf ace. However, this depth is sti1l above the water table and conditions are generally dry. Interstitial water exists as the result of percolation of meteoric water from the surface.

Jan 1, 1986

By S. R. Clark

"INTRODUCTION Of all the natural resources being taxed by the needs of the modern world, perhaps the most important is the continually expanding demand for water resources. As water becomes scarcer, and increasingly important, new technologies are needed to find innovative ways to preserve this precious resource. In Chile, for example, the mining industry is investing billions of dollars to build desalination plants and pipelines; bringing ocean water as far as 200 kilometers inland to meet their demand and maintain operations. It is a full-blown crisis for that nation and a top priority for their government and economy. It has been reported that world water consumption will increase by 40 percent in the next 10 years, representing nearly exponential growth. In the U.S., as more and more communities continue to be built, more drain on the current water infrastructure is created. For 25 percent of people and operations that rely on water from aquifers, this source is being consumed at a rate that will create significant problems meeting the demand in as few as two generations.1 A PROACTIVE APPROACH When it comes to controlling dust at your operation, whether a landfill, a transfer station, a haul road or another ancillary area, what are the options? We know watering is not the answer, but at the same time, we need to prevent dust from flying to ensure a safe environment and keep our skies clear of pollution, for both regulatory requirements and neighbors. Creating a Dust Mitigation Program instead of looking to buy the first dust control product off the shelf is a first step to conserve water and, at the same time, maintain the operational demands and environmental standards for a given site. The program concept is straightforward enough. However, the process of effectively constructing and executing a program is quite involved. When undertaking a program, each manager needs to work with their team and their partners/vendors in analyzing the following elements: 1. Site Expectations—It is important to understand how to balance your internal standards with your regulatory requirements, as well as how to keep your neighbors satisfied. 2. Site Aggregate—Variations in native soil, such as clay content or gravel levels, greatly affect the approach that will yield the highest results. 3. Climate—Relative humidity and seasonal variations are critical to achieving predictable results through product choice, application frequency and timing. 4. Daily Traffic—The type and frequency of traffic is an essential variable for site management. 5. Environmental Responsibilities—If you have additional, specifically defined responsibilities, the approach to your site may vary. 6. Budget—While efficiency is the goal of any program, some sites will have more stringent restrictions than others. 7. Current Usage Rates—Document and understand where you’re starting from, both with water, supporting products, and maintenance so that effective measurement of results is possible."

Jan 1, 2018

By C. Rutter, S. Nelson

"Climax Molybdenum Company’s Henderson Mine, owned by Freeport McMoRan Inc., is a panel caving molybdenum mine located 69 km west of Denver, Colorado. The mine utilizes long interconnected ore passes as part of the ore flow system. Knowing the approximate level of ore in these ore passes is beneficial for preventing increased dust concentrations in various production areas, as well as scheduling truck loading operations. Level monitoring has been achieved by using a strain gauge placed on the steel structure of the truck chute, an amplifier and a Programmable Logic Controller. This paper explains the concepts and limitations associated with using strain gauges for ore pass monitoring as well as applying proactive dust prevention and level monitoring interfaces. INTRODUCTION The Henderson Mine, located 69 km west of Denver, Colorado, is an underground molybdenum mine which uses a panel caving process to produce 18,000 tonnes per day currently. This process involves dumping ore down a series of interconnected ore passes leading to truck chutes. Trucks use these chutes to load ore and deliver this ore to an underground crusher. If ore is pulled below the lowest intercept of these ore passes, a ventilation pressure imbalance occurs which generates a large amount of dust on the levels where ore is being loaded into the tops of the ore pass. When a dust event occurs, work must be stopped until the dust settles. Once the dust settles the ore passes must be filled significantly before trucks can start pulling from the corresponding chute. This downtime and unplanned work due to dust can be avoided if the approximate ore pass levels are known. Strain gauges have been installed and tested on a truck chute at the Henderson Mine and the results of these tests have led to a series of concepts in using strain gauges to monitor ore pass levels. This paper explores these concepts and corresponding limitations and explains how the application of ore pass monitoring can be achieved with the use of strain gauges. Ore Pass and Ventilation Pressure Imbalance Overview At the Henderson Mine, there are typically two or four ore passes in different drifts that combine into one bin to create an ore pass complex as shown in Figure 1. When the level of ore is at or below the 7210 intercept (I82W), four drifts have a ventilation connection to each other and the 7655 exhaust level. A “piston effect” is created each time a bucket of muck is dumped down the ore pass. Figure 2 illustrates this phenomenon: as the loader in 621 dumps a bucket down the ore pass, the muck pushes the air in the ore pass down the 82A leg and back up the 82B leg which generates a large amount of dust. The bin regulators on 7655 cannot be opened enough to allow for this surge of air to be relieved onto the exhaust level and the dust ends up exhausting into the 625 and 627 drifts."

Jan 1, 2018

By Robert D. Brown, Charles A. Sorrell

The decade of the 1980's saw "advanced materials" become a key factor among the industrialized nations, with the United States, Japan, and the European Economic Community being the major competitors. All three have identified communications technology, advanced materials, and biotechnology as the keys to future industrial leadership and the closing decade of the 20th Century is expected to be an era of rapid development and restructuring. The progress of EC'92, the effort to develop uniform standards and remove trade barriers in Europe; the determination of Japan to commercialize advanced structural ceramics, alloys, composites, and superconductors; and the emergence of less developed countries as major supplies of commodity materials pose enormous challenges to the position of the United States as an industrial and financial leader. A consensus is developing that the industries that are first to commercialize the large array of new structural materials and electronic, optical, and magnetic materials and devices will be those who determine the structure of national and world economics. Many technical, economic, legal, political, social, and cultural factors are important determinants in the race to commercialize new materials. Millions of words have been written about these factors and their interdependence; yet the sheer complexity of the problems, the rate at which changes are taking place, and the economic risks involved are so great that government policy makers and industrial decision makers find adequate understanding to be very difficult. Of the many factors involved in advanced materials, the Bureau of Mines has the statutory responsibility to provide information on where materials can be found and how they are mined, extracted, purified, combined, and recycled. It is obvious that minerals availability is essential to implementation of any new technology just as there can be no commodity metals industry if the ores are not available. Because "minerals availability" for commercialization of advanced materials and devices is more complex than for commodity materials and a new mix of materials and processes is emerging, the Information and Analysis Directorate of the Bureau of Mines is redirecting resources to provide reliable information for policy and decision making. The Office of Advanced Materials Coordination (OAMC) was established as a staff operation in July 1987 to assist the efforts of the divisions and branches. The key issues and problems were defined and the role of the Bureau was outlined (Sorrell, 1987, 1988). In February 1990, the functions of OAMC were transferred to the new Branch of Advanced Materials, a line organization parallel with the Branches of Ferrous, Nonferrous, and Industrial Minerals, and was given the responsibility for developing new methods to acquire, analyze, and disseminate information about new materials. The purpose of this paper is to provide definitions, a summary of major issues and problems, an overview of minerals and processing availability problems, and a perspective of the ways in which the mining and materials industries can help to ensure domestic availability of raw and processed materials.

Jan 1, 1990

By William A. Vogely, Lawrence J. MacDonnell

This section begins with an introduction to several key environmental laws. This is followed by a discussion of some of the issues raised by such environmental regulation. Finally the subject of regulatory reform is addressed. Overview of Selected Major Environmental Laws The number, type and complexity of environmental laws and regulations affecting mineral resources development have grown at an astonishing rate since the 1960s. The most significant laws and regulations are those addressing the use of the public lands; those concerned with air quality, water quality, and surface reclamation; and those defining government responsibility for its actions having important environmental consequences. The laws and regulations governing activities on the public lands will be taken up in the section 5.15C, "Minerals and Land Management." In this section we will concentrate on five primary laws: the Clean Air Act, the Clean Water Act, the Surface Mining Control and Reclamation Act, the Endangered Species Act, and the National Environmental Policy Act. The Clean Air Act: The legislative and regulatory framework for controlling air pollution has developed in a series of steps. Most important for present purposes are the Clean Air Act of 1970 (P.L. 9 1-604) and the 1977 Amendments (P.L. 95-95). The rather complex air quality control scheme includes four key elements-national ambient air quality standards, state implementation plans, the prevention of significant deterioration program, and the non- attainment program. National Air Quality Standards. The 1970 Clean Air Act is a landmark law because it contains the first explicit recognition that pollution is a nationwide problem requiring a national control program. The federal government through the Environmental Protection Agency (EPA) was to establish national air quality standards for at least the six pollutants named in the Act (sulfur dioxide, carbon monoxide, total suspended particulates, photochemical oxidants, hydrocarbons, and nitrogen dioxide). These standards were to be established so as to protect public health, "allowing an adequate margin of safety." The cost of achieving these standards is not to be considered. The 1970 Act unrealistically required that these standards be achieved in all areas of the country by 1975. As the program has developed, the air quality control regions are now to be designated as "attainment" or "nonattainment" with respect to each of the national standards. State Implementation Plans. Under the Act the states are given the primary role in achieving the ambient standards. States are to develop and implement control plans governing emissions from all existing and new sources. These plans can include emission limitations for existing stationary sources, transportation control plans to reduce emissions from mobile sources, and pre- construction review of new stationary sources to assure compliance with new source performance standards. The EPA must approve all state implementation plans. Sanctions are given to the EPA to be applied if states fail to submit acceptable

Jan 1, 1985

By T. W. Camm, J. C. Johnson

"Most engineers are bright, hard-working, reliable, and prefer to avoid conflict. An engineering curriculum tends to self-select these characteristics. By most standards, you would expect workers exhibiting these traits to require minimal supervision. But is this true? Is this how most current engineering managers lead? Looking at some current theories on leadership combined with personal anecdotes, this presentation will look at some common misconceptions about leading engineers. INTRODUCTION Engineers are different. There, I said it. From cartoons to movies to television shows and more, there is a reason stereotypes of engineers resonate. Yes, you can find a lot individual variation among specific engineers that you may know, but they do not detract from some of the overarching commonalities that engineers are known for. CLASH OF CULTURES What distinguishes a professional? Raelin (1985), in his book Clash of Cultures, describes professionals as having superior intellectual training, maintaining their own standards of excellence, and being supported by associations that maintain the quality of the profession. Engineers obviously fit all three of these ideas: an engineering degree is still regarded as one of the most difficult to attain; we maintain our own standards both through peer-review and in academia through ABET accreditation; and through professional associations like SME to promote the discipline and foster technical growth. Six characteristics representing professional status are described by Raelin (1985, p. 9): Expertise—prolonged specialized training in a body of abstract knowledge. Autonomy—the freedom to choose the means to solving a problem. Commitment—Primary interest is in pursuing the practice of one’s own chosen specialty. Identification—identifying with the profession and with fellow professionals, both through formal associations and through peers external to the organization. Ethics—providing service without concern for oneself or without becoming emotionally involved with the client. Standards—committed to help in policing the conduct of fellow professionals. Engineers are smart—in the vast majority of cases they are hired specifically for their expertise. At a typical mine the ventilation engineer knows more about mine ventilation than anyone else on site; the same is true for the rock mechanics engineer, the explosives engineer, the planning engineer who uses sophisticated computer software—each is the expert for their particular area at the mine, that is why they have that responsibility. This can present a dilemma for the manager for each (sometimes all) of these engineers. The manager needs to keep everyone on task and focused on the objectives of the organization. Because they have reached their position by following the norms and expectations of the organization, managers tend to have a certain amount of loyalty to that organization. Engineers, on the other hand, tend to have mixed loyalties, having as much loyalty and affinity for their profession as they do for the particular company they happen to be working for at any given time. This dynamic can often lead to power struggles between the managers, based on their positional authority in the organization, and the engineers, based on their specialized knowledge (Camm, 2013)."

Jan 1, 2017

By Bo Kyung Sim, Dae Young Kim, Jae Won Lee, Ebrahim Farrokh

"The contract C931 of the downtown line 3 (DTL3) mass rapid transit system of Singapore includes half a kilometer twin tunnels running between Mattar and Macpherson stations. An EPB TBM of 6.6 m diameter was used to excavate both of these tunnels. The tunnels pass predominantly through a very stiff silty/clayey fine to coarse sand from the Old Alluvium Formation. In this paper, TBM selection procedure, TBM performance evaluation, and some of the tunneling operation challenges with the TBM in the Old Alluvium Formation are discussed. In this regard, soil conditioning trial tests were performed to resolve the clogging issue and low TBM performance. Thorough TBM operational data analysis was performed to detect high soil abrasivity, backfill grout leakage, and foam nozzle clogging. The results of some of the applied modifications are also discussed to show their effects on the TBM performance improvement. Finally, some of the challenging TBM design specifications are also discussed. INTRODUCTION Tunneling and underground construction in Singapore has been increased in the last 30 years due to the demand for public transportation systems and the limited space above the ground for the infrastructure development. Downtown Line Stage 3 (DTL3) Mass Rapid Transit (MRT) system has 21 km total route length and consists of 16 stations. DTL3 Contract C931 runs between Mattar station and MacPherson station. The construction works in this contract include twin bored tunnels of 6.6 m diameter and 450 m length and a TBM launch shaft of nearly 30 m depth. The tunnels run in urban area below Kallang Paya Lebar Expressway tunnel (KPE), Kallang River Canal, and Circuit Link. Figure 1 shows the alignment of the tunnels in between two subway stations. The tunnels were excavated by an earth pressure balance (EPB) tunnel boring machine (TBM) through the Old Alluvium (OA) formation, a challenging geological formation in the sense of its abrasivity and stiffness. The Old Alluvium Formation mostly includes stiff to very stiff clayey and silty sand. The soil is un-weathered cemented to semi-cemented dense, mainly with a low permeability coefficient of 10-7 m/s and high SPT values (almost 100). The soil is classified as “very high abrasive” according to NTNU SAT test classification (SAT value of 15 to 42). The construction of the first tunnel drive was slowed down due to a number of factors related to soil conditioning and TBM operation. In this regard, a thorough analysis of the TBM operational parameters from the excavated sections was performed to identify the problems in time to prevent unwanted construction delays in the subsequent sections. In the following sections, a brief overview of the criteria used for TBM selection is presented at first. Then, the results from the analyses and tests performed to assess soil conditioning, grout leakage, and soil abrasion are presented. The last section discusses some of the tunneling design features that challenged the TBM operation in this project."

Jan 1, 2016

By Tim Neil, O&apos

Introduction On the banks of the Columbia River, about halfway between Seattle and Spokane, sits Wenatchee, WA. It calls itself "the apple capital of the world." And it has a gold mining history that dates back to the 1880s. It was just outside Wenatchee - three blocks outside, to be exact-that Asamera recently dedicated its $60 million Cannon underground gold mine. At full production, it is estimated the Cannon mine will yield between 5 and 5.6 t/a (160,000 and 180,000 oz per year) of gold. That would make Cannon the largest North American underground gold mine to be brought into production this year. Cannon should also be among the top 10 of all North American gold producers. Asamera officials project Cannon's operating costs at about $4.8019 ($150 per oz). At that rate, the mine should also be one of the lower cost and most profitable gold mining operations in North America. One reason for low operating costs is low electric power costs. The Cannon operation will be paying about 2.5 cents per kWh for hydroelectric power supplied by the Bonneville Power Authority. Proven and probable ore reserves at Cannon are in excess of 4.7 Mt (5.2 million st). Reserve grades average 7.29 g/t (0.21 oz per st) of gold in three ore zones, in order of discovery - B, B West, and B North. The ore bodies could have been mined by open-pit methods. But underground mining was chosen for environmental reasons. In addition, the rich B North ore body extends beneath a nearby horse stable and arena. The Cannon mine area comprises some 20 km2 (5000 acres) in Chelan County. The mine site is located at the 305 m (1000 ft) elevation in Dry Gulch at the base of the Cascade Mountains. The initial estimate of mine life for the Cannon operation is eight years, depending on gold prices. But Asamera officials believe the Wenatchee area has excellent potential for future gold discoveries. Asamera, Inc. of Calgary, Alberta, owns 51% of the Cannon property, through its wholly-owned Asamera Minerals (US). Breakwater Resources Ltd. of Vancouver, British Columbia owns 49% of the operation. The Cannon mine is named in honor of longtime Asamera, Inc. executive and current company director, geologist Donald G. Can¬non. It was he who first brought the Wenatchee property to Asamera's attention and urged the company to pursue it. Asamera is a major explorer and producer of oil and gas. Its Cannon operation is the largest and most significant to date in its mining division, according to Rob¬ert G. Welty. He is Asamera's chairman and chief executive officer. It should be noted there was an element of serendipity involved in Cannon's development. The development program be¬gan when geologist Cannon visited the Wenatchee area. He was visit¬ing old mining districts. He liked what he saw. The Cannon property was eventually optioned for ex¬ploration, including a modest drilling program.

Jan 12, 1985

By G. I. Voiloshnikov, V. E. Dementyev

Wide use of adsorption methods for metal recovery is one of the most important achievements of gold metallurgy of the last decades. Anion exchange resins or activated carbons may be used as adsorbents. This paper presents a brief overview of IRGIREDMET effotts on development, testing and implementation of techno­logical flowsheets using both adsorbent types and attempt to compare their technological properties. IRGIREDMET Institute was founded in 1871 as a laboratory for gold smelting and gold ore testing. In 1930 it obtained the status of the Research Institute. IRGIREDMET functioned as leading research center for gold mining industry in the former Soviet Union. At present it is the Open Joint Stock Company dealing with all s01t of research and design works for gold min­ing (ranging from geology to gold refinery). IRGIREDMET started development of ion exchange technol­ogy in 19641• The first stage of work (1964-1970) including development of principle flowsheet of RIP process was carried out jointly with the Moscow VNIIKHT Institute (All-Russian Scientific Research Institute of Chemical Technology)2• The flowsheet of RIP process is presented in Fig. I and includes the following basic operations: gold adsorption from pulp; washing of loaded resin; acid treatment; thiourea adsorp­tion; gold elution by acid thiourea solution; resin washing to remove thiourea; alkaline treatment of resin; resin washing and gold recovery from eluates by electrowinning. The technology developed and equipment used were tested for treatment of clayey ore of Kuranakh deposit at a pilot plant of the Lebedinsky gold complex ("Aldanzoloto" company, Yakutia, Russia). The pilot plant throughput was 200 t/day. At the same time IRGIREDMET conducted the tests on ion exchange technology for ore and concentration products of oper­ating gold plants and for ores of new deposits. Laboratory and pilot plant tests were done and developed initial data and process design criteria for designing of 15 plans of the former Soviet Union. In the course of this work a great number of newly synthe­sized anion exchangers including strong and weak base resins was studied, the peculiarities of anion exchange resins using two different raw material types ( ores and concentrates includ­ing clayey, carbonaceous, silver bearing, arsenic, antimony and base metals bearing products); some theoretical regularities of adsorption process were investigated; the technology of two stage adsorption of gold and silver from silver gold ore, improved flowsheet for gold elution and resin regeneration, design of adsorption equipment including pulsation columns, design of electrowinning cells were developed; conditioning technology for pulp with complex ion composition prior to gold and silver adsorption was developed, etc.3·8• IRGIREDMET specialists took part in commissioning of practically all the plants in the former Soviet Union using RIP and RIL process including Lebedinsky, Kuranakh, Sovetsky, Karamken, Matrosov's plant and Mnogovershinny plants. Due to this works RIP process became standard technology for Russia and the CIS.

Jan 1, 1998

By Peter J. Lawson, John A. Rideout, Gregory W. Dicinoski

A considerable body of literature directed towards optimising the efficiency of gold and silver extraction from cyanide leach liquors has appeared in recent years. A few examples from dissolution to solvent extraction to adsorption in carbon-in-pulp (CIP) and resin-in-pulp (RIP) operations follow. Selective leaching of gold from copper-gold ores using ammonia-cyanide mixtures extends the % copper which may be tolerated in ores (Ruane, 1991, LaBrooy et al., 1991, Costello, 1991). The removal of copper and recycling of cyanide from high copper ores is another important development (Sceresini and Staunton, 1991). Solvent extraction of alkaline cyanide liquors (Riveros, 1990, Mooiman & Miller, 1991) and solvent aided elution in CIP (Muir, et al., 1985) look promising. Recent definitive papers on the mechanism of adsorption of aurocyanide by activated carbon should lead to more efficient use of CIP (Adams and Fleming, 1989, Klauber, 1991). Strong and mixed weak-strong base resins have been applied in RIP for aurocyanide extraction in Russian Plants since the 1970's (see for example Borovskii et al., 1985, and references cited in Fleming, 1988a). Fundamental studies on applications of commercial weak and strong base resins-in-pulp (Fleming & Cromberge, 1984a, b, Fleming 1988a, Hosking 1984, Riveros and Cooper 1987) have generated much interest in RIP. Detailed comparisons of CIP vs RIP efficiencies at Mintek in South Africa (Fleming et al., 1988b), and the inefficiency of CIP in contact with clay led to the commissioning of the strong base RIP Golden Jubilee plant in 1988. Its operation and improvements have been reported (Seymore and Fleming, 1989, Fleming & Seymore, 1990). The use of anion exchange membranes for aurocyanide extraction shows some promise (Mauthoor et al., 1991). However, the development of new gold specific resins at Mintek (Green et al., 1984, 1986, 1990, Johns and Green, 1991) and elsewhere (Asker et al., 1987, Wilson et al., 1987, Harris et al., 1992) should improve the viability of RIP processes. The polydiallylamine gold specific resins (Hodgkin & Eibl, 1988, Fawell et al., 1992a, b) have high capacities for auro cyanide recovery from high concentration liquors. The use of guanidine based liquid and solid ion exchange extractants for gold was recently reported by the Henkel Corporation (Kordosky., et. al., 1993). Such specific resins tailor made for gold and/or silver cyanide extraction should lower overall cost by improving metallurgical efficiency. In the case of strong base resins this selectivity largely eliminates the problems of poor base metal elution and/or poisoning. The work reported here outlines the approach taken at the University of Central Queensland to synthesize sterically hindered strong base anion exchange resins which are designed to have high selectivity for auro- and argentocyanide complexes. It summarises selectivity tests on low grade cyanide leach liquors from several mines. It also examines an RIP vs CIP comparison, and investigates the elution properties and cycling of one such promising resin.

Jan 1, 1993

By Gail L. Achterman

Most mining companies today perform site assessments and operational or compliance audits regularly. The purpose of these audits is to review company facilities and operations to determine whether they comply with applicable federal, state and local environmental laws and regulations. Why Audit? Companies adopt assessment and audit programs for legal and business reasons. The business reasons include: (1) ensuring efficient and cost-effective compliance through early problem identification and resolution; (2) planning and implementing business transactions such as real estate conveyances, loans, mergers and acquisitions, and waste disposal service contracts; and (3) employee training and relations. Legal reasons for audits include: (1) avoiding enforcement actions and penalties; (2) meeting environmental permit certification requirements; (3) avoiding corporate officer liability; and (4) meeting Security and Exchange Commission disclosure requirements. The Environmental Protection Agency ("EPA") encourages environmental auditing by regulated entities. The EPA Environmental Auditing Policy Statement was published in the Federal Register on July 9, 1986 (51 Fed Reg 25,004). Although the existence of an auditing program does not create a defense to or otherwise limit a company's regulatory responsibilities, EPA considers compliance programs in setting inspection and enforcement priorities. If a company makes an honest effort to identify and correct its own problems, EPA's enforcement approach is influenced, especially if violations are promptly reported. Perhaps more significant to many executives, the U.S. Department of Justice issued guidelines last year on when it will pursue criminal prosecution for environmental violations. See Department of Justice, "Factors and Decisions on Criminal Prosecutions for Environmental Violations in the Context of Significant Voluntary Compliance or Disclosure Efforts by the Violator," (July 1, 1991). It is now commonplace to read about major companies pleading guilty to criminal violations and paying millions of dollars in penalties. For example ALCOA recently agreed to pay criminal fines and civil penalties totaling $7.5 million for unauthorized excavation of PCB-contaminated soil and improper dumping of spent caustic solution. No executive wants to explain to the Board of Directors or shareholders why the company was criminally indicted. The Department of Justice considers factors such as voluntary disclosure, preventive measures and compliance programs, such as a regular compliance auditing program, the effectiveness of the disciplinary system for employees who violate the company's environmental policies, and subsequent compliance efforts by companies to remedy ongoing noncompliance. The Department of Justice looks closely at whether audit recommendations were implemented in a timely way and whether environmental compliance was a standard by which employees were judged. The Lawyer's Role. The role of the lawyer in an audit team deserves special attention. When enforcement action or litigation has begun or is contemplated or a government agency has asked for information, attorneys always should be directly involved in environmental audits. In most situations, however, environmental audits are management tools, and the attorney's role should be to advise the team. The attorney can help make sure the team understands the laws and regulations the facility must

Jan 1, 1992

By R. Timothy McCrum

It is not often that the Interior Department's Bureau of Land Management, Office of the Solicitor, and Interior Board of Land Appeals (IBLA) jointly act to do the mining industry a good turn. That happened, however, in the recent decision, Schlosser v. Pierce, 92 IBLA 109 (1986). It was ruled that the theorized "independent mine requirement" was not a part of the discovery standard for mining claim validity under the 1872 Mining Law. The phrase "independent mine requirement" would require the mineral reserves within the boundaries of each individual mining claim in a claim group to support an independent economic mining operation. This, without regard to the fact that reserves on adjacent claims could be mined in a group operation, resulting in greatly reduced mining and marketing costs per ton of ore. Such a rule would render invalid under the 1872 Mining Law mining claims for almost all low-grade, high-tonnage, commercially valuable mineral deposits. Until the Schlosser case, no judicial or administrative decision had addressed the issue of the independent mine requirement. Nonetheless, a series of Interior decisions in the 1970s implied such a rule. Even the Rocky Mountain Mineral Law Foundation reluctantly concluded in 1984 that, "each claim to be valid must be capable of being operated at a profit independently of any other claim," the Foundation did criticize the rule as "excessively stringent" and urged the adoption of a "more realistic rule." Fortunately, the IBLA did just that in Schlosser when it ruled that the "application of a requirement that each claim be independently capable of being mined and marketed at a profit is rejected," 92 IBLA at 134. Now, a year after the 1986 decision, there remains some unwarranted confusion over the issue resolved in, and the meaning of, the Schlosser decision. There is no need for this confusion. The Interior Department's decision is a clear and legally sound victory for the mining industry. Grazing rights vs. mining claims The Schlosser case was an unusual mining claim contest. A private contest was brought before the Interior Department. Schlosser was a federal grazing lessee and surface owner. He filed against Pierce, the locator of a group of mining claims for bentonite over the same lands. At a hearing before interior's administrative law judge (alj), Schlosser's counsel began laying the foundation for the independent mine requirement. Counsel asked the mining claimant's expert whether he would go through the permitting procedure, road building, and reclamation just to mine the amount of bentonite on any one claim in the group. Schlosser's counsel proceeded with this line of questioning for each of the 16 claims in the group. Pierce's mining expert testified that the tonnages of mineral on any individual claim could not be mined, processed, and marketed at a profit if only one individual claim was considered. However, if the claims in the group were operated jointly, all the mineral could be mined, processed, and marketed at a profit.

Jan 8, 1987

By M. Pawlik

Canadian sylvinites contain over 90% of KCl and NaCl and a few percent of water-insoluble minerals. Cationic flotation is used to produce KCl concentrates. Since water-insoluble minerals appear in the pulp as slimes, and since long-chain primary amines are utilized as a collector, desliming is essential. The potash industry utilizes different desliming methods. This may involve selective flocculation of the slimes with polyacrylamide and removal of the flocculated product by flotation, or mechanical desliming with the use of classifying cyclones. Whichever method is applied, desliming is never complete; the flotation feed after desliming still contains about one percent of the slimes which heavily affect collector consumption and flotation selectivity. Therefore, the remaining slimes have to be rendered inactive by “blinding” them with polymers such as carboxymethyl cellulose or guar gum. The commercial blinders used by the potash industry include natural and synthetic polysaccharides. The most common is the use of carboxymethyl cellulose (CMC) and guar gum (GG). These are quite different polymers, while CMC is anionic, GG is non-ionic; while the applied CMCs are of relatively low molecular weight (about 300,000) GGs have much higher molecular weight. Guar gums are also heavily used as the depressants of naturally floatable gangue in the processing of platinum-bearing ores, and according to Harris et al. (1999) quite a large variety of modified guar gums are available in South Africa for this application. Cheng et al. (2002) claim that natural guar gum’s molecular weight is 1.935 • 106. Robinson et al. (1982) found that the molecular weights of five grades of commercial guar gums ranged from 4.4 • 105 to 16.5 • 105. The highest molecular weight sample is then very close to the natural guar gum studied by Cheng et al. (2002). According to the manufacturer, the Rantec KP4000 guar gum which is used by the Canadian potash industry has a molecular weight of about 1.5 x 106. Since both KCl and NaCl are soluble in water, the flotation process is carried out in saturated brine. At 20 oC, 1450 kg of NaCl-KCl-H2O saturated solution contains about 0.300 kg of NaCl, 0.150 kg of KCl, and 1 kg of water (Gaska et al., 1965). Thus, in the saturated NaCl-KCl brine there are about 5.1 kmole of NaCl and 2 kmole KCl per 55.5 kmole of water. This gives 3.9 molecules of water per each ion assuming complete dissociation of NaCl and KCl. Thus, it is obvious that all water molecules in the saturated brine must be bound in the hydration shells around the hydrated ions. The surface tension of the NaCl-KCl saturated brine was recently measured to be 85 mN/m (Laskowski et al., 2003).

Jan 1, 2004

By K. J. Henderson

INTRODUCTION Shrinkage mining at Inco Ltd.'s Crean Hill mine can best be defined as a horizontal breasting method utilizing the broken ore for the mining floor and to provide wall support, with draw from a series of boxholes or draw¬points at the base of the stoping block. In choosing to shrink a given block of ore, the initial investigation centers on the ore configuration and grade, the expected ground conditions in the stoping area, the expected profit compared to alternative mining methods, the future production requirements, development lead time, the availability and type of equipment in the area, and the availability of experienced miners. These factors are weighed against other mining methods and shrinkage mining is chosen when the advantages outweigh the dis¬advantages. These will be discussed in more detail later. At Inco Ltd.'s Crean Hill mine, shrinkage mining makes up 17% of total mine production and is decreasing due to the advent of advanced blasthole techniques, notably in-the-hole drilling. Shrinkage is an adaptable mining method that is currently employed in narrow irregular ore zones, as undercuts for in-the-hole blast¬hole stopes, in ore bodies that do not extend from level to level, and in areas where quick production is required with a minimum of capital outlay or minimum develop¬ment. Two major types are currently in use which are classified on the basis of type of draw system employed. These are the utilization of load-haul-dump (LHD) equipment drawing from drawpoints, and the slusher and train method drawing from boxholes into a slusher trench and loading into a train. A third method being phased out is drawing from chutes directly into a train. In all three methods the actual stoping operation remains the same. In the initial planning of a mining block, the ore body is first located using an exploration diamond drill¬ing program. This is essentially done at a 130-m (400¬ft) spacing and it gives an indication of the amount of ore, grade of ore, the configuration of the ore body, as well as other geological features such as ground condi¬tions which will affect future mining. This drilling is done from an exploration drift 165 m (500 ft) long in the hanging wall and covers a vertical extent of 330 to 670 m (1000 to 2000 ft). However, these data are not accurate enough for detailed planning. When the de¬cision has been made to mine, a preliminary develop¬ment drill drift is driven in such a position that it can serve the dual purposes of allowing the ore body to be drilled off in detail, or of later serving as a haulage or access drift. Diamond drilling from this drift is usually on a 15-m (50-ft) grid spacing and gives adequate information for detailed planning. Utilizing the drill data, a decision is made on the mining type. For a shrinkage operation, the stoping block is ideally 49 m (150 ft) in length and a maximum of 13 m (40 ft) in width. Lengths of 65 m (200 ft) are considered a practical maximum because of the length of time the back of the stope remains open during the min¬ing of a cut. A minimum length of 13 m (40 ft) is used because the amount of time spent in opening a new cut increases in comparison with the total stoping time. The maximum width of 13 m (40 ft) is used because ex¬perience with the ground indicates that generally stope backs tend to be unstable over greater widths. However, widths of 33 m (100 ft) have been mined. A minimum width of 5 m (15 ft) is used to allow an effective draw, but in unusual cases, a width of 3 m (10 ft) has been mined successfully. The dip of the ore should not be less than 1.04 rad (60°). Angles flatter than this will not pull properly resulting in inefficient mining because of ore hang-ups on the footwall side of the stope and the need for large stagings on the hanging wall. In considering shrinkage, mining ground conditions play an important role. Strong shearing, cross faulting, or dikes are avoided. These usually cause dangerous mining conditions and an alternative safer mining method which will give adequate support to these adverse ground conditions is employed. Production requirements are taken into considera¬tion when planning a shrinkage mining program. In it¬self, shrinkage mining is capable of producing ore in a relatively short time with little capital development. If quick production is required, this method can produce ore rapidly as all that is required is that the draw system be completed and the miners with jacklegs and stopers produce a limited amount of ore. The obvious disadvan¬tage is that not all the ore broken can be pulled from the stope immediately. However, a mining horizon with sev¬eral shrinkage stopes in different stages of production can adequately maintain scheduled tonnage require¬ments, the cycle being stopes under development, stopes actively mining, and stopes completed and pulling. When the decision has been made to use shrinkage mining in a given block, the haulage and draw system is driven. The proximity of the orepass system dictates whether the system is to be a LHD operation or a slusher trench operation. If the orepass system is in close prox¬imity to the stoping block, LHD equipment is employed because of its ability to operate efficiently over short haulage distances. A long tram to the orepass usually dictates a slusher trench operation with haulage by train. Internal orepass systems are used effectively with LHD equipment with a load-out and retramming taking place on a lower horizon. In addition, stoping blocks in older areas of the mine are developed track because of the capital cost involved in converting an existing level to trackless mining. DRIFT DEVELOPMENT USING LHD EQUIPMENT The haulage drift for a draw system using LHD equipment is driven parallel to the ore body in the foot¬wall at a sufficient distance to allow an 11.5-m (35-ft) drawpoint to be driven into the ore (Fig. 1). The actual position of the drift depends entirely upon the ore con¬figuration and the drift size depends on the equipment to be used. Drift sizes of 4.6 x 4.1 m (14 x 121/2 ft) for an St-4 and 3.8 x 3.6 m (111/2 x 11 ft) for an St-2 meet company and government clearance standards and allow sufficient space to accommodate a ventilation pipe. The

Jan 1, 1982

By O. A. Velasquez, A. R. Kumar

"Continuous miners are often equipped with a flooded-bed dust scrubber to clean the air from close to an active underground coal mining face. However, its impingement screen is prone to clogging due to an accumulation of dust, thereby lowering the scrubber’s efficiency and potentially exposing the mine workers to higher levels of dust. Fans can compensate for the increased resistance by varying their operating parameters, but the scrubber screen needs significant maintenance which leads to downtime. The authors have proposed a suitably sized Vortecone as an alternative to the conventional flooded-bed dust scrubber system. Water is used as the filter medium, which is replaced and recycled continuously. Preliminary CFD investigations of Vortecone scrubbers have indicated higher cleaning efficacies, especially in the respirable range. This paper presents the results including the flow characteristics and capture efficacies of a full-scale Vortecone. Multi-phase flows, including free-surface modeling and particle tracking methods, have been adopted. ACKNOWLEDGEMENT The authors acknowledge the National Institute for Occupational Safety and Health (NIOSH) for funding this research project. This research is being developed with the support of a NIOSH Grant 200-2014-59922- ‘Coal Mine Dust Mitigation through Novel Scrubber Development and Numerical Modeling’. The views expressed in this paper are those of the authors and do not necessarily reflect those of NIOSH. This project is aimed at designing novel and efficient scrubbing systems for underground mining operations. The authors acknowledge Dr. Thomas Novak of the Department of Mining Engineering, the University of Kentucky for his support and encouragement. The authors also thank Dr. Sunil Vytala, CFD engineer at Cradle CFD for his invaluable inputs to the numerical models.INTRODUCTION Continuous miners are the main production machines deployed in room and pillar mining operations. These miners extract coal by the shearing action of the wethead cutting drums. Strategically placed water sprays on the drum not only cool the bits extending their useful service life, they also suppress the dust at the point of generation itself. A flooded-bed dust-scrubber (Campbell, et al. 1983) is usually integrated onto the continuous miner to arrest dust from close to the active face. These fan-powered scrubbers have an impingement screen flooded with water, which also serves as the filter element. A demister downstream of the screen removes the excess water from the air cleaned. These conventional scrubbers have been found to be very effective in alleviation of respirable dust levels underground (Chao and De-sheng 2000) (Colinet, Reed and Potts 2013). However, the inefficiencies of the flooded-bed dust scrubbers arise out of their internal components. Depending on the mining conditions, the screen may be clogged by the accumulation of the trapped dust particles. The resistance of the scrubber system is increased reducing the airflow. The flooded-bed dust-scrubber system would, therefore, require frequent maintenance of the screen and the demister (Listak 2010). Since any maintenance needs to be carried out under supported roof, this leads to loss of availability of the equipment as well. In addition to this, the continuous miner operators could be exposed to elevated levels of dust when satisfactory airflow at the face is not achieved."

Jan 1, 2018

By Robert M. Anderson

A popular perception by the public and many mining claimants, is that the 1872 Mining Law provides a statutory right to mine and extract minerals from the public lands. This perception in reality, is both true and false, depending on the mining claimants' ability to meet federal and state environmental, cultural and endangered species laws. Land use decisions and proposed legislation affect exploration and development opportunities in California. It is imperative that the mining industry involve itself in the planning process to ensure that BLM decision makers are fully informed of industry's knowledge and concerns. STATUTORY RIGHTS AND ENVIRONMENTAL CONSTRAINTS "No other problem has such a sense of urgency and poses as profound consequences to the quality of life and the creation and distribution of societal wealth as how we protect the environment. Certainly, the environment is the single biggest issue facing mining and mineral activities in the new decade. David S. Brown The 1872 Mining Law was passed, ironically, the same year the nation's first National Park was established. It is a perception that the establishment of Yellowstone National Park was the beginning of the United States' earliest environmental movement; brought on, perhaps, by the rapid clearing of land for homesteading purposes and, the concern that many acres of the public domain were being disposed of through a multitude of public land laws. While there was an effort being made to designate some special and unique public lands as parks for preservation purposes, environmental concern and awareness did not lead to mandatory identification of environmental impacts and appropriate mitigation until the passage of the National Environmental Policy Act in 1970. Consequently, it is not surprising that the original United States Mining Laws of 1866, 1870 and 1872 had no mention of environmental protection. There have been numerous attempts to repeal the 1872 Mining Law over the last 50 years for a variety of reasons. Currently, there is a perception by the general public, media and even some in congress, the mining industry and BLM that a change is needed. The environmental organizations want the industry to be more accountable for reclamation and post mining uses. In Tn nEnvironmental Agenda for the Future," leaders of America's foremost environmental organizations state that the mining law "includes no protection for the environment," and therefore, should be reformed. We can all acknowledge, as stated above, that the mining law, per se, requires no "protection. However, the Bureau of Land Management (BLM) clearly has the authority and the responsibility to fully "protect" non-mineral resources while providing for the extraction and processing of mineral resources by private industry. There are about 13 major federal laws that have indirectly or directly amended the mining laws to require Environmental, Historic and Cultural Protection." There have been many mining law case decisions about the statutory and constitutional rights of miners to explore open federal lands, "stake a claimg" and extract minerals. What needs to be fully understood is how federal laws, as enumerated on Table 1, may affect these rights. What follows is a description of

Jan 1, 1991

By J. Burrows

The Chamber of Mines of South Africa is an association of major mining corporations, gold mines, coal mines, diamond mines and other metalliferous mines. It looks after those interests of its members which can best be handled on a co-operative basis. The Chamber's activities include the engagement of labour; the negotiations of all labour matters, including minimum wage rates, with recognised trade unions and associations; the carrying out of advanced technological research; representing the industry in dealings with the government and the administration of miners' training colleges and rescue training stations. Subsidiary companies of the Chamber handle matters such as the refining of gold and other metals; the processing and marketing of uranium and the marketing of Krugerrands. The thirty-two gold mines members of the Chamber of Mines of South Africa produce approximately 694 tons of gold per annum. To achieve this they employ 430000 persons and break about 8400 kilotons of rock per month. The working revenue is approximately 4 225 million US dollars per annum and the annual working profit is approximately 2 050 million US dollars. The electric power consumed by the gold mining industry is 1650 MW, about 20% of the total power produced in South Africa, and the annual costs of this power is approximately 200 million US dollars per annum. It is estimated that about 25% of this power is used for ventilation and refrigeration appliances. Thus the annual power costs for ventilation and refrigeration is approximately 50 million US dollars. The gold bearing reef is a narrow tabular deposit situated at varying depths throughout the gold fields. The weighted mean rock breaking depths and, virgin rock temperatures range from 1 700 - 9 000 ft (520 - 2 740 m) and 68 - 113°F (20 - 45°C) respectively. The maximum virgin rock temperature at which mining currently takes place is 130°F (54.5 C). Obviously at such depths and temperatures and with such a large labour force the provision of an acceptable environment is critical and to achieve this 59 000 000 cfm (28 000 m3/s) of air is downcasted during the main shift and 122500 tons (430 MW) of refrigeration are provided. Legislation in South Africa requires that on metalliferous mines when more than 1000 persons are employed underground during any one shift the manager shall appoint one or more ventilation officers. The legal responsibilities of the ventilation officers are concerned mainly with the measurement and control of dust. In practice, this is not the main part of their work and ventilation personnel perform many other duties such as measuring and controlling the distribution of air, checking the performance of fans and cooling plants, planning air and refrigeration requirements and, more recently, measuring and controlling noise and illumination levels. Ventilation personnel are specialists who provide management with advice on all matters relating to the mine environment. At the present time there are 506 persons engaged as ventilation personnel in gold mines and a further 1744 persons are employed in gold mine ventilation departments in a non-technical capacity, for example as construction workers, filter cleaners, fire patrollers, etc.

Jan 1, 1980