Search Documents

By P. J. Best

Due to its low mine production costs, competitive rail rates and low sulfur content, the Southern Powder River Basin (SPRB) now commands 30 percent of the U.S. utility coal market. In 1996, production exceeded 260 million tons, a growth of 110 million tons since 1989 and 15 million tons over 1995. Continued growth is expected as the second phase of the Clean Air Act Amendments (CAAA) looms. This growth will be the greatest in the southern part of the basin, where coal quality is higher. This article is an overview of supply and demand issues affecting markets for SPRB coal. It reviews the current markets for SPRB coal and addresses future prospects for market expansion.

Jan 1, 1998

By John C. Edwards, F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were con- ducted in a 180 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.1 3, and 0.06 m/s were determined at 30, 60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

Jan 1, 1997

By Dale A. Shay, Roy R. Cellan

The Santa Fe Mine, located in west central Nevada, began leaching ore in 1988 and completed ore processing in 1995. Homestake Mining Company has completed final reclamation of the site, including remediation of bare surface soils resulting from the oxidation of sulfide minerals and migration of acidity in the mine waste repositories. The need to remediate oxidized sulfides and mitigate resultant acidity at the Santa Fe Mine emphasizes the economic, reclamation, and environmental advantages for understanding and pre-planning for management of potential sulfide wastes during mine planning phases. The lack of pre-planning by mining companies for sulfide waste management was common in the 1980's due primarily to mining of reserves characterized largely as oxide deposits and to the common opinion that low moisture regimes in arid or semi- arid climates would not allow for significant acid generation. Since the 1980's, operational experience has shown that sulfide wastes, deposited randomly in waste dumps and without adequate planning for final reclamation success, can create final reclamation problems that are very costly to remediate. While mine waste characterization, waste management plan compilation, and in-pit selective waste handling procedures add operational costs, the reclamation experiences at the Santa Fe Mine are indicative that pre-planning and management is worthwhile both in actual overall cost efficiency and in successful reclamation of the mine site. The reclamation program at the Santa Fe Mine shows Homestake's continued commitment to the successful management and reclamation of their mine sites.

Jan 1, 2000

By D. S. Kimbal

The McCoy/Cove mine is located 48 km (30 miles) south of Battle Mountain, Nevada, USA, in the Fish Creek Mountains at an elevation of 1548 m (5080 ft), see Figure 1. Joseph H. McCoy first discovered gold at this location in 1914. This discovery led to the Gold Dome Mine which produced the first gold from this area in 1928. After the Gold Dome era, the land remained relatively dormant until Houston oil and Minerals Corporation purchased the claims from the Summa corporation and defined an ore body at the present day McCoy pit. In 1986 Tenneco Minerals (formerly Houston oil and Minerals corporation), sold the McCoy mine and adjoining claims to Echo Bay Minerals corporation. The Cove ore body was discovered soon after the sale to Echo Bay. Echo Bay expanded the heap leach operation and built the present mill which began processing ore in the fall of 1989.

Jan 1, 1993

By Richard Keith Corbin

INTRODUCTION The purpose of this paper is to assist explorationists and entrepreneurs in deciding whether to invest in gold mining concessions in lesser developed countries (LDCs) and, if so, in deciding which LDCs provide the best opportunity. The first decision is difficult in the face of common notions that foreigners are not welcome - only their money; that the best gold deposits were worked out long ago; that even if you survive the mal- aria, and in spite of 51% control by a national partner, you manage to profit from a new discovery, they will tax your operation to death, or worse yet, nationalize it. Close scrutiny of what happened to foreign investors in LDCs during the “Mexicanizationt” of the 1930's through the "Zambianization" of the 1970's shows that many of these concerns are well-founded historically. But the trend of knowledgeable writers over the past decade seems to be away from this gloomy foreboding, and towards a cautious optimism, based on recently perceptible metamorphoses in certain LDCs' conditions and attitudes. If the explorationist or entrepreneur decides to seize on this apparent opportunity, the second decision -- which of these certain LDCs to invest in -- is doubly difficult, because of the formidable tasks of coming up with a rating system to provide rational comparison, and then gathering enough current, reliable information to apply. To assist in these tasks, a suggested rating system and case studies, respectively, follow a brief review of recent writings on the subject

Jan 1, 1987

By Malcolm J. McPherson

Observations of environmental parameters in mines have traditionally been made by means of hand-held instruments, these being employed as a basis to ensure that atmospheric conditions in the mine remain within limits commensurate with safety, to safeguard the health of personnel, and to ensure that statutory requirements are met. Thus, starting from the first flame safety lamps of the early nineteenth century, numerous portable instruments have been devised over the years to indicate levels of dust, temperature, humidity, and concentrations of gases including oxygen, methane, and carbon monoxide. Similarly, portable instruments have been used to measure air velocity and pressure. For routine monitoring purposes, hand-held equipment suffers from many disadvantages. Readings are intermittent, often with long delays between successive observations, making short-term trend analysis impossible. Portable instruments are more liable to damage; they are labor intensive and provide a very limited amount of information either for control or planning purposes. The 1960's and 1970's have seen an accelerated development of mine environmental monitoring equipment. Alarm methanometers to give localized audiovisual signals became more common. These were followed by a variety of instruments which gave local, then local/remote continuous records, particularly of methane concentration and airflow. More sophisticated transducers and transmission systems were developed allowing further parameters to be monitored. This led to a proliferation of paper strip and chart recorders which had to be maintained and inspected regularly for trends and abnormalities.

Jan 1, 1979

By F. M. Doyle, Jun Li, Milton E. Wadsworth, Ximeng Zhu, E. Peters

The electrochemical behavior of pyrite in borate/sulfate solutions was investigated using cyclic voltammetry. Three anodic peaks at approximately -0.8 V, -0.1 V and +0.5 V (SCE) were detected along with their corresponding reduction peaks. The first two peaks correspond to the oxidation of surface products. The third peak corresponds to the direct oxidation of pyrite with reaction products FeO oxides. sulfate ion and partially oxidized sulfur intermediates present as a surface film of polysulfides and So. The Few oxides and sulfur intermediates were reduced to ferrous hydroxide and HS during the negative-going scan. The HS interacted preferentially with Fe(OH), on the surface to form FeS. Excess fenous hydroxide continued to reduce to metallic iron. During the return positive-going scan, metallic iron was oxidized to ferrous hydroxide and FeS was oxidized to pyrite. These reactions are characterized by a unique double peak observed in the region -0.8 to -0.65 V. The growth kinetics of the surface sulfur film formed during anodic oxidation were studied using chronoarnperomeay. Potentiostatic measurements were well correlated by a paralinear rate equation, suggesting the formation of an intermediate passive film, associated with the simultaneous dissolution of the outer layer of the film. The reaction rates were affected by applied potential, solution pH and temperature, but were independent of electrode rotation speed. A reaction kinetics model which fitted well with experimental results, was developed.

Jan 1, 1993

By D. Kwak, S. Han, J. Kim, Y. Lee

"INTRODUCTION In carbonate rocks, it is difficult to characterize due to the high degree of heterogeneity in pore geometry. Carbonate rocks have various types of pore systems such as fractures and vugs, and this heterogeneity should be considered for more realistic prediction of oil production in carbonate reservoirs. This study carried out water flooding experiments using five carbonate rock samples in order to observe the change of physical properties. Firstly, qualitative and quantitative analyses were conducted for each carbonate samples by use of XRD and XRF to evaluate the mineral content. All samples are mainly composed of CaCO3 and after that, the ICP experiments were carried out for the water passing through the carbonate. As a result, it was possible to measure the quantity of CaCO3, MgO, Fe2O3 component in water and due to this effect, the permeability of carbonate was altered especially in the front part of the core. Finally, after the carbonate was saturated by 30 API crude oil, water injection to enhance the oil recovery was repeated and it was confirmed that the oil-producing characteristics are different depending on the dissolution characteristics of carbonate rock samples. CORE SAMPLE ANALYSIS Porosity and Permeability Experiment Porosity and permeability were measured. The procedures are as follows (Figure 1). 1. Measure the diameter and length of the dry core using Vernier caliper. 2. Put the core in the core holder, run vacuum pump until the inlet and outlet pressure gauge equal. 3. Saturate the core using ISCO pump to inject water at 650 psi 4. Measure the amount of water and calculate the porosity 5. Set up the outlet pressure at 500 psi. 6. The flow rate measure when the equilibrium 7. Calculate the permeability through Darcy’s Law. 8. Cutting of core upstream and downstream about 13cm, and measure the each of permeability."

Jan 1, 2016

By C. G. Treworgy

Geologists at the Illinois State Geological Survey are evaluating geologic and land use conditions that affect the minability of coal to determine how much coal is available for development using current technology and mining practices. Coal resources are being evaluated for selected 7.5-minute quadrangle study areas. In a central Illinois study area, more than 25% of the deep-minable resources were limited from development by unstable roof conditions resulting from thick unconsolidated sediments overlying thin bedrock overburden. In some southern and southeastern Illinois study areas, geologic conditions associated with a paleo-channel limit the minability of significant resources of low-to medium-sulfur coal. Some features which were thought to limit mining, such as areas of closely-spaced oil wells, have been found to have minimal impact on the amount of coal recovered.

Jan 1, 1995

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are sometimes large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy/Bureau of Mines- sponsored subsidence study currently underway at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County), West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar retreat mining. The initial findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water bevels at shallower depths.

Jan 1, 1985

By Milka Madahana, John Ekoru

Particulate matter is one of the leading pollutants in the mines and in the communities in the areas near or surrounding the mines. The availability of large Clinical and environmental data sets obtained from the mines has brought about the need to use better approaches to analyze the collected data. Prediction and control of particulate matter concentration in the mining environment is essential in minimizing air pollution and protecting the respiratory health of mine workers. The main objective of this research work is to analyze datasets obtained from a mining area using machine learning techniques which will then be followed by the real-time estimation of dust particulate in the mines. Datasets collected over 8 years in an hourly sampling rate from an open cast mine is cleaned and analyzed for trends and patterns. Artificial Neural Networks (ANNs), Support Vector Machines and decision trees techniques are applied to analyze and predict the particulate concentrate. The estimation of particulate concentration using Artificial Intelligence will significantly contribute toward the development of quantitative tools to be used in correlating of cause and effect of dust concentration in mines. The results obtained in this work will form a sub-unit of a respiratory health monitoring system for mine workers. The system is essential in the collection, analysis, and tracking of mine workers’ respiratory health, thus it forms part of an early intervention system for mine workers. From the existing theory, we expect the Artificial Neural Network will perform much better than previously used classical models.

Jun 25, 2023

By Y. Guan

The adsorption of zinc species onto silica in ammonical solutions has been studied. Adsorption isotherms reveal that increasing adsorption occurs as the solution pH is made more alkaline. Fr-IR spectroscopy revealed that the adsorbed species is a zinc ammine complex.

Jan 1, 1993

By Adrian C. Dorenfeld

The lesser developed countries (LDC's) may be classified into two categories: 1) oil producers, and 2) non-oil producers. The non-oil producing LDC's, as a class, are at present in very difficult financial straits. (1) Since the quadrupling of world market crude oil prices in 1972, an ever greater share of the LDC's export earnings have gone to pay for oil imports, in-stead of national reinvestment. The LDC's inter-national debts--much of it to pay for oil--have soared to record levels, with consequent limits for future credits. (1) Again, this inhibits future national investments, and there does not seem to be an end to the future increase of Organization of Petroleum Exporting Countries (OPEC) prices. Indeed, some of the economic difficulties in some metal markets--particularly the imbalance of production vs. markets for copper, can be traced indirectly to the OPEC cartels' heavy-handed impact on copper producing LDC's which must produce copper at any price to meet their oil bills. (2) Among the major oil importing LDC's are the Philippines and South Korea. 50th nations have substantial cement industries. The South Korean industry is geared for major export markets in the Far East. Both nations have ambitious plans for economic growth in order to accommodate burgeoning populations with ever increasing expectations for high standards of living. These plans had some success, more or less, until the high OPEC oil cartel charges had to be borne. Now, in common with all oil-deficit areas, the Philippines and South Korea are seeking lower cost sources of energy. Both countries have coal deposits. In the case of the Philippines, the reserves are in scattered, relatively small deposits. Most of the coal deposits are faulted, folded and, in general present formidable production problems for limited reserves. Nonetheless production has been on the order of about 70,000 to 150,000 tons per year in the last 30 years. Prior productions (1920-1941) varied between 9,000 Co 150,000 tons per year. (13)

Jan 1, 1978

By M. Z. Rashad

The purpose of this work is to determine the influence of sample length or size on the value of variance (Semivariogram) to select the suitable length that is required to the geostatistical computations of ore evaluation. Three cases in Ghorabi Iron Ore were studied. The first one was on the iron fraction (Fe%) at which the semivariogram gave an evidence to good continuity of the fraction in the ore. In this case, the length of sample has not important influence. The second case was for the Mn% component of the same area where the semivariogram has a nugget effect. The selected length for this case was 4 meters. The Cl% fraction of the ore was the third case where the anisotropic phenomena was appeared and the suitable length is 3 meters.

Jan 1, 1992

By A. G. Journel

Accurate prediction of recoverable reserves are key to the development and planning of a mining operation. Recovery functions for tonnage, quantity of metal and ore grade are defined and two approaches for their estimation are proposed. The indicator kriging (IK) approach draws on the data rank orders, whereas the multi-gaussian (MG) approach relies on a grade multi-variate distribution hypothesis. Although based on different premises, both approaches yield remarkably similar--and accurate--estimates for recoverable reserves.

Jan 1, 1984

By M. Canty

Results are presented that were gathered during pilot-and field-scale testing of an innovative technology, sulfate-reducing bacteria (SRB), designed to treat and control acid mine drainage (AMD). The project was performed under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy through an Interagency Agreement. The MWTP is implemented by MSE, Technology Applications, Inc., located in Butte, Montana. Sulfate-reducing bacteria, a common group of anaerobic bacteria, produce hydrogen sulfide and bicarbonate when supplied with sources of carbon and sulfate. Hydrogen sulfide reacts with metal ions in AMD, precipitating them as metal sulfides; the bicarbonate serves to help neutralized the drainage. Pilot-scale testing was performed within eight packed-bed reactors at a temperature representative of a field application of this technology in a northern climate, nominally 8°C. The reactors, packed with an organic substrate, were operated continuously in upflow configurations receiving AMD at a flow rate corresponding to a 5-day retention time over a test duration of 60 days. During this time, numerous physical and chemical parameters were monitored. Pilot-scale metal removal efficiencies reached 99% for zinc, 99% for aluminum, 96% for manganese, 98% for cadmium, and 96% for copper. Iron and arsenic removal was not as effective as the aforementioned metals, which was largely attributed to the high levels of iron and arsenic contaminating the organic substrate. Evidence existed that both adsorption and sulfate reduction were occurring within the reactors.

Jan 1, 1998

By Richard H. Gates

INTRODUCTION The U. S. Army Corps of Engineers is developing chemical explosive excavation as a construction technique for use on Civil Works projects. Large chemical charges are being used in multiple charge arrays in a variety of media and topographic situations to achieve actual construction projects. The target is the development of chemical and nuclear explosive excavation as an accepted cost-competitive construction technique. Military research using explosive excavation is also being conducted to apply this technique to military engineering for combat purposes and to military construction. The information gained from both the civil and military research is integrated into the overall development of explosive excavation. This research and development work is being conducted under the auspices of the U. S. Army Engineer Waterways Experiment Station Explosive Excavation Research Laboratory (EERL) located at Livermore, California. This organization was formed in 1962 as the Nuclear Cratering Group (NCG) to carry out the Corps of Engineers (OCE) portion of a joint agreement with the Atomic Energy Commission (AEC) to develop nuclear explosives for construction purposes. The AEC, through the Plowshare Division of the Lawrence Livermore Laboratory at Livermore, California, has been responsible for developing nuclear explosives, conducting nuclear cratering experiments, developing nuclear safety information, and developing methods for predicting the shape of the craters. The Army part of the program includes corollary chemical high-explosive cratering experiments, participation in the AEC's nuclear cratering experiments, and development of

Jan 1, 1997

By W. J. Miles

Diatomaceous earth or diatomite is a sedimentary rock of organic origin that is composed principally of the silicious skeletal remains of diatoms. Diatoms are microscopic single cell acquatic plants that are related to algae. Diatoms first became abundant in the Cretaceous period from about 65 to 135 million years ago. Most of the commercial deposits are of Pliocene through recent age, and are younger than 35 million years. Diatoms are still abundant in present day lakes and seas. The living diatom is supported and protected by two half cell walls or valves united by a connecting band or girdle. These valves are composed of opaline silica extracted from the water in which the diatom lives. After death of the diatom, the silicious remains settle in the lake or sea and accumulate at variable rates approaching several millimeters per year for very active diatom colonies. This accumulation of silicious sediments, after decay of the organism, burial, and uplift, can result in the formation of diatomaceous earth deposits.

Jan 1, 1987

By Adrian Fleming

Adrian Fleming is Executive Vice President of Exploration for Golden Star Resources Ltd., Denver. Adrian is an Australian who graduated in 1973 with an honors degree in geology from Newcastle University, New South Wales. His extensive international experience has spanned exploration, project development, and operations for both large and small companies in Australasia, Southeast Asia, North and South America, and Africa. Adrian has been with the Golden Star group of companies for four years and he is responsible for all exploration activity. ABSTRACT Golden Star acquired the rights to the Omai prospect in 1985 at a time when the country of Guyana was out of favor with the exploration fraternity. Subsequently in the late 1980s and early 1990s, Golden Star acquired exploration properties in Suriname and French Guiana well ahead of its competitors. Golden Star's strategy entailed identifying windows of opportunity and aggressively pursuing them. We also recognized that the Guiana Shield hosted a significant area of highly prospective greenstones which were comparable in metallogenic potential to similar terrains in eastern Canada, western Australia and west Africa. The geological skills Golden Star developed and the exploration techniques employed to explore deeply weathered rocks are described. The paper highlights the key elements of Golden Star's strategy and illustrates how some of the milestones reached by the company led Golden Star to establish an enviable portfolio of gold and diamond properties in the Guiana Shield.

Jan 1, 1998

By Donald Crowell

Due to falling metal prices and depletion of ore reserves, lead-zinc mining in the Leadville, Colorado, area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Company and ASARCO with ASARCO being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Company of Salt Lake City in conjunction with the Central Engineering Department of ASARCO. The plant was constructed by Stearns-Roger Corporation. Construction began in the spring of 1970 and the plant went onstream in April, 1971. Flow sheets and equipment lists are attached. This paper will describe the flow sheet very briefly and discuss in more detail those aspects of the design which may be of interest, particularly the provisions for expanding the capacity of the plant.

Jan 1, 1972