Search Documents

By A. Ayoubian, V. Nasri

This Tunnel Connection project will include construction of two short tunnels to connect the existing subway tunnels (Red and Blue lines) in the northern loop area of downtown Chicago through a new station. The Southeast Tunnel will connect the Red Line to the new station below the intersection of State and Washington Streets and the Northwest Tunnel will connect the Blue Line to the new station below the intersection of Dearborn and Randolph Streets. The connection tunnels are located in a very dense urban area of downtown Chicago and under several important historical buildings. Both tunnels are curved at the intersections and located at a depth of about 7.5 m below ground surface in saturated soft clay with an average undrained shear strength of approximately 25 kPa. The design calls for minimizing surface disruption and ground displacement while maintaining normal operation of the existing subways during the construction of the connections tunnels. This paper presents mining and cut and cover tunneling alternatives for the project.

Jan 1, 2007

By Joseph Ribak

Grunerite asbestos (amosite) has been shown in epidemiological and experimental animal studies to cause lung cancer, mesothelioma and pulmonary fibrosis commonly referred to as asbestosis. An overview of the human and experimental animal studies describing the health hazards of grunerite asbestos (amosite) is presented. Of the many human studies describing the health hazards of asbestos, only three factories using mainly, if not exclusively, grunerite asbestos (amosite) have been studied. The first is a series of reports on a cohort of 820 workers from a plant located in Paterson, NJ. Among this cohort, 18.7% died of lung cancer and 17 mesotheliomas occurred. The Paterson factory closed in 1954 and moved to Tyler, Texas where it operated until 1972. Among the 1130 former workers in the Tyler plant 6 mesotheliomas were reported with 15.8% lung cancer mortality. The third grunerite asbestos (amosite) exposed cohort was an insulation board manufacturing facility in Uxbridge, United Kingdom. Here 17.1% of the workers died of lung cancer and 5 mesotheliomas occurred. The lung content from 48 Uxbridge workers was analyzed by analytical transmission electron microscopy for mineral fibers. The relationship between grunerite asbestos (amosite) concentrations in the lung correlated with grades of fibrosis and asbestos bodies and was lower than the concentration found in the cases with malignant tumors. The lung cancer cases contained more grunerite asbestos (amosite) than mesothelioma cases, and in the cases of non-alignant disease the concentrations were still lower. In both types of malignancies the concentration of grunerite asbestos (amosite) was very high-over a billion fibers per gram of dried lung tissue. Occupational exposure to airborne concentrations of between 14 and 100 fibers of grunerite asbestos (amosite) per milliliter after 20 year latency causes marked increases in lung cancer, mesothelioma and pulmonary fibrosis (asbestosis). © 2007 Elsevier Inc. All rights reserved. Keywords: Grunerite asbestos; Amosite; Mesothelioma; Asbestosis

Jan 1, 2007

The purpose of the 3DOPT Program is to determine, starting from drill hole data, the optimum economic mining limits for an open pit. The economic limits are defined as those which maximize total profit, i. e. total mineral value mined less the total mining and milling costs, subject to the restriction imposed by the pit slopes. To accomplish this, the program employs the following: (1) A three dimensional matrix of equal sized blocks in order to file the engineering data and the cost/value data required to develop the profit figure for each block of ore/waste. (2) A graph algorithm developed specifically for optimizing these profits.1

Jan 1, 1966

By Kentaro Kuraji

INTRODUCTION Background Tokyo, the capital of Japan, is one of the largest cities of the world. As many as 33 million people live in Tokyo and three neighboring prefectures although the city occupies only 0.6% of the area of the country. The network of Metropolitan Expressways serves as a major artery for daily physical distribution in Tokyo. The Central Circular Route of the Metropolitan Expressway (MECCR) is located innermost among the three circular routes in Tokyo (Figure 1). Once completed, MECCR is expected to drastically mitigate traffic congestion in the central Tokyo area and provide drivers wider varieties of options in route selection. Alleviating congestion is estimated to reduce 400,000 tons of carbon dioxide emissions annually. The eastern and northern sections and part of the western section of MECCR have been completed with the total length reaching 33 km. The western section will be extended southward by approximately 4 km in the spring of 2010. An 11-km-long western section of MECCR that is currently being constructed is composed mostly of tunnels. A large number of power supply, gas supply, telephone, drinking water and sewerage pipes have been placed under the Yamatedori avenue along which MECCR is being constructed. The shield tunneling method has therefore been adopted for constructing tunnels along the route. The method involves the advancement of a shield tunnel boring machine (TBM) through the ground simultaneously assembling segmental rings within the shield. The method not only enables the building of highway tunnels more quickly and efficiently than other methods but also minimizes the effects of construction work on the surrounding area and the environment. Constructing the tunnel using the conventional cut-and-cover method might have required large amounts of time and cost because relocating the numerous objects buried under the Yamatedori avenue might have been necessary during tunnel construction. It was also considered desirable to place the tunnel at a depth of 30 m or more from surface to prevent tunnel construction from adversely affecting railways because the tunnel was expected to cross eleven railways and subways. This is one of the reasons for selecting shield tunneling as an effective method. The shield tunneling method was finally adopted for a length of 7 km in the 11-km western section of MECCR. The shield tunneling method was also employed in the Ohashi Tunnel located southernmost in the 11-km western section of MECCR. This paper describes the construction of the Ohashi Shield Tunnel.

By Christopher Snee

??care has to be taken that the design is driven by sound geological reasoning and rigorous engineering logic rather than by the very attractive images that appear on the computer screen.??Hoek 1999 Design of a cavern is inextricably linked to the engineering geology of the site. The importance of sound geological reasoning will be illustrated by transportation projects in New York City where there are proposals for at least 11 caverns. These caverns have been the subject of advanced exploration techniques and geological interpretation but even so the raw data falls short of the sophistication of modern numerical methods. This paper will give geological explanations for the engineering characteristics of the rock in New York City which will provide guidance for practitioners when approaching cavern design in New York and elsewhere.

Jan 1, 2008

By P. K. Das, S. K. Singh, C. C. Chang, E. C. Wang, R. B. Roberts

As part of the New York City’s redevelopment of the far west side of mid-town Manhattan, this project will add 1.5 miles of twin bored tunnel to No. 7 Subway Line. The proposed alignment extending from the Times Square Station west beneath 41stStreet turning south under Eleventh Avenue and terminating at 25th Street will include two new stations. The tunnels and station caverns will be primarily constructed in the Manhattan Schist, and will pass in close proximity to several major overly ingstructures. This paper discusses the lithology and structural discontinuities of rockmass along the project alignment, tunnel and cavern rock loading, groundwater hydrology, groundwater quality, groundwater treatment and sustainable design.

Jan 1, 2005

By A. Wahab Khair, John G. Oldsen, John C. Stankus, Song Guo

During the last several years, implementation of trusses, in lieu of wood cribs, has been successful for supplemental tailgate support in the Pittsburgh seam. This paper reviews, the truss support system provided by the new high strength 0.6" tensioned cable truss, which is now also being used in cribless tailgates. Cable loading and roof deformation were monitored to evaluate roof and floor performance. The test results indicate that the cable truss system successfully controlled the roof and floor during the first and second panel extraction. This paper will describe the advantages of cable trusses and their load transfer mechanism as well as mine evaluation.

Feb 24, 1997

By W. James Marold

The New Croton Aqueduct (NCA) was the first major water supply tunnel for New York City. The 50-km (31-mi) long tunnel has 33 open shafts 6 m (20 ft) to 121 m (397 ft) deep. The tunnel and shafts are lined with brick and mortar, with cast iron lining and pressure covers in six pressurized shafts. Details of the 1895 construction are provided and compared to modern construction techniques. The paper provides rehabilitation techniques for the shafts and pressure covers, including grouting, epoxy lining, temporary bulkhead design and installation and placement of tremie concrete 98 m (320ft) below the water level in a 122 m (400ft)deep shaft using a Remote Operated Vehicle (ROV) to monitor the placement.

Jan 1, 2008

By H. Fayed

Two-phase (water and air) flow in a self aerated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). A 0.8 m3 model is considered. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Because of the lack of circumferential periodicity in this machine, the entire machine is modeled and unsteady simulations are conducted in the whole volume of the bulb. Uniform bubble diameter is specified, and the effects of bubble diameter are determined by conducting simulations for three diameters of 0.5, 0.7, and 1.0 mm. The unsteady air flow rate through the machine is predicted as an outcome of the simulations. Air volume fraction contours and velocity field in different parts of the machine are presented and discussed.

Jan 1, 2012

By Rafael C. Castro

As part of its risk management plan, the South Central Connecticut Regional Water Authority (RWA) is assessing the condition of its system of raw water conveyance tunnels and connecting pipelines. In 2006, the RWA inspected one of the system?s main tunnels, a 4-mi, 1950s-era tunnel that had not been inspected since its construction. The inspection team prepared extensively for the unknown conditions in the tunnel, and the inspection was completed safely and successfully. This paper describes the team?s pre-entry preparations, dewatering and ventilation efforts, surface-to-tunnel communication, access, physical inspection of the tunnel, and the lessons learned throughout the process. Additionally, this paper will preview planning for the subsequent inspections.

Jan 1, 2008

By Keith A. Heasley, Lee W. Saperstein

This paper investigates the use of backfill zones and yielding pillars for subsidence control. The investigation begins by choosing an appropriate subsidence predictive technique to simulate the proposed subsidence-control schemes. Two case studies are performed in order to delineate the accuracy and utlility of the chosen predictive technique and then the results of these case studies are used to establish appropriate sets of regional site parameters. Next, a detailed analysis of the major variables affecting the outcome of the subsidence-control simulations is conducted and graphical displays of the exact sensitivity of the surface subsidence to these variables are given. Finally, alterations to the surface subsidence that are expected from using two major subsidence-control techniques are presented. The first technique to be assessed is a backfilled pillar centered longitudinally in a panel. With this arrangement, a minimal amount of backfill material can produce substantial decreases in vertical displacements. The second technique to be assessed is the use of yielding gate pillars to reduce the sinuosity of the transverse subsidence over adjacent panels. With proper design, this technique can greatly curtail surface strains and help minimize remedial drainage control.

Jan 1, 1986

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article is based on research report data from minecost.com and Metalytics Pty Ltd which detail the specific carbon dioxide emissions for 208mines producing 90% or more of western world copper, zinc, lead and nickel in 2007. The copper and nickel mines also include Norilsk in Russia, KGHM in Poland and Kazakhmys in Kazakhstan. This is the first time that such information has become available.

Jan 1, 2009

By Staff

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several stages—basic (mining), intermediate processing, manufacturing of finished goods and construction. The estimated growth rate for the real GDP of the United States for 2006 was 3.2 percent. The nominal GDP was about $13.2 trillion. The value of minerals mined in the United States in 2006 rose significantly because of increased unit price for some metals—particularly copper, zinc and other base metals. There was also a significant reduction in metals stocks. Infrastructure expansion and manufacturing in China and India have been absorbing a significant portion of world output. Domestic production increased for some industrial mineral materials, mainly cement and construction sand and gravel. Production of crushed stone declined less than 1 percent in 2006 compared

Jan 1, 2007

By S. Fawell, H. R. Manouchehri

The main electrophysical properties, i.e., dielectric constant and electrical conductivity, of pure calcite, quartz and wollastonite mineral samples were measured and their triboelectric charge attributes were investigated by contacting minerals particles with different tribochargers made from different materials. In addition the energetic work function values for mineral samples were estimated due to their acquisition charge. Besides, the behaviour of triboelectrically charged of different particle size fractions of mineral samples were inferred. Finally an attempt were made to translate the findings from single mineral systems to a real carbonate ore. The results exposed good prospects to beneficate the examined minerals by triboelectric separation.

Jan 1, 2002

By J. J. Gresham

Homestake’s first links with Australia were established in 1934 but it wasn’t until 1961 that the company established a formal presence in the country. After involvement and success in iron ore and nickel, Homestake made a strategic investment in the Kalgoorlie gold operations in 1975 and now owns 50% of Kalgoorlie Consolidated Gold Mines, operators of Australia’s biggest gold mine. In 1998 Homestake acquired the major Australian gold producer Plutonic Resources, is now firmly established as Australia’s second largest gold producer and is actively seeking further opportunities for growth in the Austral-Asia region. Homestake’s success in Australia has been the result of important strategic alliances, timely investments, a long term commitment to the region and perseverance during periods of depressed commodity prices.

Jan 1, 2001

By J. Drzymala

Particle beneficiation tests are often conducted to determine how the recovery of a key component of a particle mixture varies with overall product yield, i.e., the separation curve. The results can be misleading when an attempt is made to determine the effect of feed grade by comparing separation curves representing different feed grades or key component concentrations. This is a shortcoming of the conventional recovery versus yield diagram, which may not appear to be affected by feed concentration. To overcome this shortcoming, a method is presented for transforming and normalizing the recovery and yield coordinates so that the separation curves representing dif-ferent feed concentrations are directly comparable.

Jan 1, 2007

By Steve Kral

The mining industry in northern Ontario is known mostly for its huge nickel deposits. Inco’s and Falconbridge’s nickel mines in the Sudbury Basin are the best known. And with nickel prices being what they are, interest in the region continues. And how. Inco and Falconbridge want to merge. Teck Cominco wants Inco, but without Falconbridge. Xstrata made a hostile bid for Falconbridge, which Falconbridge rejected. And, in June, Phelps Dodge trumped them all when it made an approximately US$40-billion friendly offer for Inco and Falconbridge in a two-part deal.

Jan 1, 2006

By J. C. Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult because a slope will transverse through many different types of strata. Over the past three years, Keystone Mining Services, LLC, an affiliate company of Jennmar Corporation, has developed a new methodology designated the ?Stress, Geologic, and Support Design System (SGSsm)?. This patent pending method analyzes the stress, geology, and support design for a mine slope. It has been successfully applied in various new slopes across the United States. This paper will detail the main concepts of the methodology including: (1) Analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) Primary and supplemental support design; (3) Long term support design in the form of steel square sets or arches, and (4) Validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.