Search Documents

By Alfred Haack, Günter Girnau

INTRODUCTION From 1967 to 1976 in the Federal Republic of Germany about loo km tunnels and 125 underground stations were constructed for municipal and commuter railways solely. Additional a remarkable amount of road tunnels and sewers were built. In 1977/78 a further 27 km railway tunnels, 3.5 km road tunnels and 65 km sewers and utility lines were under construction. This shows an enormous volume of tunnel construction work. In connection with this activity various technical research and development programmes have been carried out. They deal with nearly all fields of underground works as for example soil and ground exploration, excavating and lining techniques, calculation and last but not least waterproofing problems. It is impossible within the framework of this report to touch on all the problems. Therefore, only one problem area with its different aspects will be discussed: waterproofing systems and their last developments in Germany, especially, joint sealing with special consideration of the waterproofing of concrete segmental tunnel lining (1)

Jan 1, 1979

By Duk-Wom Park

INTRODUCTION he most important information required for the engineering design of structures in rock is its inherent rock properties. Without providing adequate parameters on the rock property, high quality of the engineering design cannot be expected. Many laboratory rock testing methods have been developed, but they are mostly for testing intact homogeneous rock without appreciable discontinuities. In reality, the intact rock properties do not represent the behavior of rock masses because rock masses include irregularities such as joints, cracks, interlayers, variations in mineral compositjon, etc. In general the type and intensity of the rock defects may be much more important than the type of rock which will be encountered (Terzaghi, 1977; Bieniawski, 1984). In-situ rock testing can provide better information on rock parameters, but it takes a tremendous amount of effort, time and cost. In recent years, numerical modeling techniques are gaining popularity as a design tool for structures in rock bodies due to the enormous progress in computer technology (Wang, 1985; Kripakov and Melvin, 1983; Park and Ash, 1985), but it is quite dangerous to use numerical techniques without having proper input data. Bieniawski (1984) states as follows: Some design methods such as numerical techniques have outpaced our ability to provide the input data necessary for the application of these methods. In order to provide an adequate amount of input data, an extensive testing program may be required, thus major efforts in time and expenses are commonly spent, In this paper, a new rock testing method, which utilizes the principles of laser holographic interferometry, is introduced. This method requires only a few minutes to measure the modulus of elasticity and quality of a rock core sample, which does not have to be cut or ground. The Poisson's ratio can also be measured in a few minutes from a sliced rock specimen. HOLOGRAPHIC INTERFEROMETRY Principles of Holographic Interferometry In 1948, Gabor invented holography, which is the technique of reviving three dimensional images using a monochromatic light source. A full demonstration was not made then because a clean monochromatic light source was not available. Later, in the early 19601s, the laser was adopted as a monochromatic and coherent light source (Leith and Upatnieks, 1963). Since then, applications have been made in many different fields ranging from crime prevention to three dimensional television. In this technique, an image is usually recorded by means of constructing a hologram which is a record of the interference pattern formed on a high resolution photographic system as shown in Figure I. A beam splitter divides the laser beam into two beams: (1) an object beam which is expanded while passing through a beam expander and illuminates the object, and (2) a reference beam which is expanded and illuminates the holographic plate. Subsequent to an exposure, the holographic plate is developed and illuminated by the expanded reference beam. The original scene of the object is revived in a three-dimensional image. The entire instrument should be placed on a vibration free environment. The wave fields reflected by the object in two slightly different configurations can be superimposed to form an interference fringe pattern. Thus, it is possible to measure the displacement that took place between the two configurations. This method is called holographic interferometrv. There are two methods of achieving this phenomena. The first is the double exposure method, wherein two exposures of the object are made prior to developing the film. The first exposure represents the original condition and the second, the disturbed condition. The second method is the real time holographic method. In

Jan 1, 1986

By R. Woods

"Comments on the paper ""Formation of hydrogen peroxide by chalcopyrite and its influence on flotation,""by A. Javadi Nooshabadi and K. Hanumantha Rao (Minerals & Metallurgical Processing, 2013, Vol. 30,No. 4, pp. 212-219)The formation of hydrogen peroxide from water during the grinding of chalcopyrite in a nitrogen-sparged environment, as reported by Javadi Nooshabadi and Rao (Minerals & Metallurgical Processing, 2013, Vol. 30, No. 4, pp. 212-219), is questioned on the grounds that oxidation of water by the mineral is unlikely to be thermodynamically feasible. It is argued that it is more likely that any peroxide that had been formed would have been generated from residual oxygen in the nitrogen-flushed system than from the oxidation of water.The formation of hydrogen peroxide by finely divided pyrite had been reported by a number of authors (Borda et al., 2001; Borda et al., 2003; Cohn et al., 2006; Schoonen et al., 2006; Schoonen et al., 2010; Jones et al., 2011; Javadi Nooshabadi et al., 2013). That hydrogen peroxide is formed in the presence of oxygen in solution can be comprehended from wellestablished mechanisms. Pyrite in aerated solution is known to oxidize by an anodic process that is coupled with the cathodic reduction of oxygen (Holmes and Crundwell, 2000). The latter process has been shown to occur through the formation of hydrogen peroxide (Biegler et al., 1975; Ahlberg and Broo, 1996). The pH dependence of cathodic oxygen reduction at other sulfide minerals, including chalcopyrite (Biegler et al., 1977; Rand, 1977), implies a similar mechanism at these surfaces."

Jan 1, 2015

By Hassan El-Shall, Rosana M. Macedo Borges, Ponisseril Somasundaran, Regis Stana, José Renato B. Lima, Patrick Zhang

The phosphate fertilizer industry is a large activity in Brazil because the soil has a phosphorous deficiency. The phosphoric acid that is produced is extensively used in the production of fertilizer. It is produced by reacting phosphate carbonaceous rock with sulfuric acid, generating phosphogypsum as a by-product. In 1991, there were about 29 million tons of phosphogypsum stored in Brazil. This has increased to an estimated 280 million tons in 2001. While the phosphogypsum is used in the cement industry and also in agriculture, the quantity used is much less than the production rate, and the stockpiles are still increasing. The radioactivity of this waste may not allow its continued use as a construction material and some other uses. However, Brazilian phosphogypsum contains a smaller quantity of radioactive materials than is reported for phosphate rocks from other countries. One important reason is the geological origin of the Brazilian apatite. All the large deposits being currently mined are igneous, not sedimentary, as is the majority of the phosphate rock produced around the world. An extensive study is being conducted to characterize the phosphogypsum generated in two production facilities in Sao Paulo state to develop safe uses for this waste and determine the environmental impact caused by the present method of phosphogypsum disposal.

Jan 1, 2002

By Akira Usui

Ferromanganese crusts on topographic highs in the western Pacific Ocean are believed to be potential resources of cobalt, nickel and platinum. Earlier shipboard geological and geophysical studies by Japanese organizations have focused on mapping of distribution of thickness and metal contents of the deposits when estimating the total reserves. This paper summarizes our attempt to obtain more feasible data of distribution patterns and configuration of the deposits which are important parameters for resource evaluation at some seamounts in the South Pacific Ocean. Morphology of the seamounts and micro-topography of the sea floors are described using shipboard acoustic remote sensing, deep-tow sonar images, and TV/camera. [ ]

Jan 1, 2008

By Paul F. Richardson

Liquids containing suspended solids are encountered in most mineral processing applications. Solids levels cover a very wide range, from ppm levels in cooling water systems to slurries containing greater than 70% solids. When the aqueous phase is recycled or further processed, a solid/liquid separation process is used. Chemical additives used to carry out this process are called coagulants and flocculants. In other cases, one seeks to control or modify the properties of the suspension. Dispersants are chemicals used to aid in suspending solids in a liquid as well as to control the properties of the resulting suspension. Dispersants find a range of uses in mining and mineral processing such as scale control, filter aids, flotation aids, and slurry viscosity modification. Materials used as dispersants include inorganic salts, alkalies, organic surfactants, and polyelectrolytes. This paper discusses the use of dispersants in mineral processing, with an emphasis on control of slurry viscosity. The mechanism of dispersion and factors that affect the choice of dispersant will be discussed.

Jan 1, 1986

By L. W. Stanger, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Douglas N. Halbe

Gold mineralization at the Mercur Mine was controlled primarily by structure and secondarily by lithology in Mississippian-age sedimentary rocks. Gold was localized where Sevier-age high angle northeast-striking faults are intersected by younger northwest-striking fault zones. The Lulu Graben is a northeast- striking fault zone composed of a south-dipping master fault coupled with subsidiary or antithetic faults. The Twist Fault zone, a sinuous, low-displacement , north-striking zone of fracturing, bisects the graben. Large- tonnage disseminated ore bodies formed east of the Twist Fault zone within silty, thin-bedded, bioclastic carbonates. West of the Twist Fault zone, gold was restricted to rock near peripheral faults surrounding a subvertical collapsed pipe developed within the graben. An overlying thick carbonaceous shale capped the ore zone. Presence of abundant limited- displacement faulting and of hydrothermal jasperoid is associated with cartonate-hosted disseminated gold. Conversely, increased fault displacement and widespread brecciation are associated with reduced dissemination of gold into normally receptive carbonates.

Jan 1, 1990

By John R. Keith

Keith, John R. 1968. Relationships of lead and zinc contents of trees and soils, Upper Mississippi Valley District. Preprint, Fall 1968 Meeting, Soc. Mining Engineers of AIME. Lead and zinc contents of elm, maple, and oak trees and of soils in which the trees grew were determined in samples from the Upper Mississippi Valley mining district, and from an area outside but contiguous to the district. The lead and zinc analyses of plant materials served to differentiate the mineralized and non-mineralized areas. Stems contained about two times as much lead and about 2-5 times as much zinc as did leaves taken from the same stems. Lead and zinc analyses of all soil horizons could be used to differentiate between the two areas. Soils at most sample sites in the mineralized district seemed to be more reliable than plants for geochemical prospecting and are a more practical sampling medium. Soil samples from areas with thick loess cover, however, failed to indicate the presence of mineralized bodies whereas tree samples from the same sites contained anomalous amounts of lead and zinc. It is suggested that in areas of thick loess cover plant samples could be used in prospecting for lead and zinc.

Jan 1, 1968

By Susan T. Bagley, Kenneth L. Rubow, David H. Carlson, Bruce K. Cantrell, Winthrop F. Watts

Permissible exposure limits (PELs) have been established for gaseous pollutants, carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), nitrogen dioxide (NO2), and some gas-phase hydrocarbons emitted in diesel exhaust. There is, as yet, no PEL recommended for diesel exhaust aerosol (DEA), nor is there a standard method for sampling this aerosol. The University of Minnesota and the U.S. Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size-selective inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were made in underground coal mines that use diesel equipment. The mine mean DEA concentrations for the five mines surveyed, determined with the PDEAS in the haulageway, was 0.89 mg/m3 with a standard deviation of 0.44 mg/m3. DEA contributed 52 % of the respirable aerosol at this location. In three of the mines filter samples were collected for DEAassociated polynuclear aromatic hydrocarbons (PAHs) and biological activity determinations. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust. In general, the PAH and biological activity levels were similar for all three mines, and indicate that up to 25 % of the haulageway concentrations may be contributed by outby diesel vehicles. Measured concentrations of CO, C02, NO, NO2, and SO2, were well below regulated levels. INTRODUCTION Diesel exhaust contains pollutant gases, such as carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and gas-phase hydrocarbons, as well as DEA. Much of the health-related concern focuses on DEA and associated organic compounds (Watts, 1992a). A wide variety of these PAHs have been identified and some are known carcinogens and/or mutagens. The U.S. Mine Safety and Health Administration (MSHA) has proposed new PELs for these and other contaminants (MSHA, 1989). MSHA has also published an advance notice of proposed rulemaking to establish a separate PEL for diesel particulate (MSHA, 1992). The U.S. Bureau of Mines has collaborated with the University of Minnesota to develop and field test a PDEAS. The PDEAS is a three stage sampler based on the MSA' personal respirable dust sampler. It utilizes a respirable cyclone preclassifier followed by a 0.8 µm cut point impactor and afterfilter operating at a flow rate of 2 L/min. Respirable aerosol greater than 0.8, µm in size is collected by the impactor while DEA, less than 0.8 µm in size, is collected by the afterfilter. Hence, gravimetric analysis of the afterfilter permits measurement of DEA concentrations. This development and laboratory evaluation of the PDEAS were described previously by Cantrell (1990) and Rubow (1990). During field tests of the sampler, numerous air quality measurements were made in continuous miner sections of five underground coal mines that use diesel haulage equipment. These air quality measurements included levels of selected PAH and biological activity associated with DEA collected in the intake and haulageway areas of three of the five underground mines, and CO, CO2, NO, and NO2 in two of the mines. The objectives of this paper are to present the DEA and associated pollutant concentrations measured in these mines and to assess the impact of diesel face-haulage equipment on underground mine air quality. MINE DESCRIPTIONS The mines used for the PDEAS evaluation were designated J, K, L, N, and 0. Mines K, N, and 0 are located in the Western United States, while mines J and L are located in the East. Each mine produces high volatile, bituminous coal with shift production levels varying from 500 to 2000 tons/section. Seam heights varied from 1.5 to 3.0 m. Mines K and N use continuous mining to develop longwall panels. The others are strictly room-and-pillar operations using continuous miners. The number and types of diesel-powered vehicles used at these mines were described by Watts (1992b). Mines J, K, N, and 0 use diesel power to assist in a wide range of activities in addition to coal haulage. These included road maintenance, personnel and materials transport, lubrication, and welding. Mine L used only three diesel-powered shuttle cars to haul coal. SAMPLING AND ANALYSIS METHODS Aerosol Measurements Aerosol samples were collected in the mine portal area, the clean air intake to the continuous miner section, the haulageway one crosscut inby from the feeder breaker and belt, in the return airway, and on selected personnel. The haulageway sampling site was located near the point where the diesel-powered shuttle cars turn around to dump their loads. Additional respirable and DEA samples were collected and have been reported by Haney (1990).

Jan 1, 1993

By G. J. Lindenburg

The Velvet mine is located in the Big Indian district of the Colorado Plateau. The general area, also known as the Lisbon Valley district, is about 65 kilometers southeast of Moab, Utah and about 120 Kilometers southwest of Grand Junction, Colorado. As shown by the slide, the Velvet area is typical of the high desert of the southwest United States. The elevation at the decline collar is 1,967 meters above sea level. To date, the Velvet has produced 1.5 million kilograms of U308 and 2.1 million kilograms of V205. The current production averages over 4,000 metric tons of ore per month. Access to the Velvet mine is by a 1,160 meter long decline. Fresh air is supplied through the decline and a 152 centimeter cased borehole. Contaminated air is removed by two 152 centimeter cased boreholes. The east side of the mine is mined using a conventional room and pillar method; whereas the west side is mined as combination conventional and random room and pillar,

Jan 1, 1983

By Yuting Xue, Khaled Mohamed

The failure of coal ribs is a major hazard in underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have been working on the development of an engineering-based rib control method. A user-friendly standalone application, called Design of Rib Support (DORS), is being developed to ease the calculations of rib support. DORS can estimate the Primary Rib Support Density (PRSD, ton/ft2) for development loading. However, it still needs to take account of another key factor, bolt length, in rib support design. The bolt length can be estimated from the rib fracture depth, and this study focuses on the coal rib fracture depth analysis with numerical modeling and artificial neural network. A total of 331 FLAC3D simulations with different mining scenarios and rib conditions were conducted for this study. Machine learning was then used to predict coal rib fracture depth under different conditions. Based on the numerical simulations, the parameters for mining scenarios and rib conditions were collected as features for machine learning, and coal rib fracture depths were collected as the target to predict. Good data correlation (r-square) was obtained with the use of an artificial neural network. The

By J. B. Hiskey

INTRODUCTION The extraction of gold and silver from ores, concentrates, and various metallurgical products can be achieved by a number of hydrometallurgical techniques. The solvation properties of alkali cyanide solutions on gold and silver were recognized 200 years ago. A cyanidation process for leaching gold from its ore was patented in 1887 and 1889 by MacArthur and Forrest. The solvent action of thiosulfate on gold and silver was observed over 100 years ago. Recently, several patents have been issued for processes using ammonium thiosulfate as lixiviant for precious metals, Berezowsky, et. al (1978) and Kerley (1981). Tozawa and and coworkers also examined the dissolution of gold in ammoniacal thiosulfate solution. Thiourea leaching of gold and silver initially discussed by Plaksin and Kozhukhova in 1941 but has received only limited attention since that early work. Use of thiourea as an alternative to cyanide was the topic of several papers presented at the 1981 AIME annual meeting In Chicago, Illinois. Hiskey provided a review of the fundamental chemistry of the dissolution of gold and silver in acidic thiourea solutions. Pyper and Hendrix reported on the leaching of a finely disseminated gold ore using thiourea as a lixiviant. The review article(6) previously presented was fairly comprehensive covering Important contributions to the chemistry of thiourea and the processing of gold and silver with acidic thiourea solutions. A search of the technical literature was made to determine recent (since 1981) progress and developments in applying thiourea to the processing of gold and silver. This review reveals that Soviet and Eastern European scientists are continuing to make major contributions to our understanding of thiourea/precious metal systems.

Jan 1, 1984

By J. Girard-Dwyer, J. Johnson, J. Whyatt

The choice of fragmentation method is one of the most fundamental aspects of mine design, and often has a major impact on the safety and economic viability of an operation. Almost exclusively, underground mining operations rely on either mechanical excavation or drill and blast techniques to extract rock. Each of these fragmentation methods has distinct advantages and disadvantages, and each is appropriate, and economic, for different mining conditions. However, the choice of fragmentation method can have a pronounced effect on the amount of damage created in the rock mass surrounding the opening. This paper reviews a number of case studies where both mechanical excavation and traditional drill and blast were used in underground mines. Ground support requirements in the mechanically excavated areas are compared to the support requirements in the blasted sections in order to demonstrate the potential safety and cost benefits of the various fragmentation methods.

Jan 1, 2003

By M. A. Rodrigues da Silva Enríquez

One of the rare consensual points among different resource-based economic analytical approaches refers to the strategic role of rent from mineral extraction, as a decisive tool to ensure that the temporary wealth generated in the present can turn into permanent income in the future. For this reason, evaluation, distribution and use of mining rent plays a central role in the sustainable development of mining cities. Brazilian legislation provides for this at the municipal level by means of participation in the financial results of mineral extraction accomplished in these municipalities, with the Financial Compensation for Mineral Exploration (CFEM). CFEM is a type of ad valorem royalty, which charges taxes of up to 3% of the net revenue of mineral production. However, legislation does not establish how these resources should be used. Therefore, there is wide variation in the use of CFEM income among Brazilian mining cities. A study from a sample of the 15 largest mining cities in eight Brazilian states made possible identification of two main patterns with regards to the use of CFEM which were labeled "sustained use" and " the pitfall of the single treasury." In that regard, this article discusses the pressuring factors that contribute to these patterns, as well as the institutional arrangements which may be more favorable to inducing more sustained use of CFEM.

Jan 1, 2011

By B. R. Utz

The goal of the DOE Coal Preparation Program is to provide industry with the scientific and engineering knowledge base to produce economically competitive and environmentally acceptable clean coal products for both existing and new markets. The DOE/PETC in-house program continues to conduct fundamental, exploratory, and applied research in the areas of physical, chemical, and microbial coal beneficiation to assist in meeting these goals and objectives. The Coal Preparation Division now has a new Coal Preparation Process Research Facility that allows continuous bench-scale testing of emerging coal cleaning technologies and ancillary coal preparation equipment at feed rates up to 1,250 kilograms (1.25 tons) per hour. Bench-scale and laboratory-scale research projects at PETC cover areas such as 1) the use of micronized-magnetite for fine-coal, 2) heavy-media cycloning, 3) fine coal reconstitution, 4) development and testing of coal preparation process flowsheet simulators, 5) dry coal beneficiation using electrostatic methods, 6) tracer methods to determine the efficiency of density-based separations, 7) selective oxidation of organic sulfur, and 8) microbial removal of pyrite and organic sulfur from coal. This paper will discuss several of these research areas.

Jan 1, 1993

By Kadri Dagdelen, Thys B. Johnson, Salih Ramazan

Long-term production scheduling design is a very important part of mining because it determines the economic outcome of a project There have been many attempts to solve the optimum pit scheduling problem, but there has been no success in developing a scheduling method to give optimum results in maximizing net present value of a mining project. Open pit production scheduling problem can be formulated as a mathematical programming problem and solved using Mixed Integer Programming technique. However, it is not possible to solve the formulation within a reasonable time since the number of integer variables required for the mathematical model is too great to do that by today's available computer technology. There- fore, a methodology is required to combine, or aggregate, the mining blocks and to decrease the number of integer variables in scheduling without losing the optimality. Therefore, the fundamental tree concept was developed in this paper to combine the blocks. A fundamental tree is defined as any combination of blocks such that: 1. the blocks can be profitably mined, 2. the blocks obey the slope constraints and, 3. there is no subset of the chosen blocks that meets 1 and 2. A Linear Programming (LP) formulation is developed as a mathematical model to find a set of fundamental trees that exist for a deposit. Since the blocks are combined to form the fundamental trees, the number of variables required for the scheduling model is decreased significantly. This decrease in the number of variables makes it possible to mathematically formulate the multi-time period scheduling problem as a Mixed Integer Programming (MIP) model. A case study is performed on a multi-mineral copper deposit in Peru, South America. NPVs of annual after-tax cash flows generated based on the schedule provided by the "Fundamental Tree Algorithm" is compared with NPVs resulted from the schedules coming from three of the computer packages presently available to the mining industry. These are Mintec's M821V, Earth- work's NPV Scheduler, and Whittle's Milava open pit mine schedulers.

Jan 1, 2002

By Chi M. Phan, Anh V. Nguyen, Geoffrey M. Evans, Graeme J. Jameson

Surfactants are used to control the interfacial properties of the gas-liquid and liquid-solid inter- faces inflotation. This paper investigates the dynamic adsorption of surfactants at the gas-liquid intelface. The dynamic adsorption process was modeled by considering the surfactant mass transfer to the gas-liquid interface by dimion and the Langmuir and Frumkin adsorption isotherms. The numerical computation was applied to solve the non-linear governing equations. The dynamic adsorption was measured in tenns of the dynamic surface tension using the pen- dant drop method. The theoretical modek were compared against the experimental data obtained with non-ionic (Dowfroth 250) and ionic (sodium dodecylbenzene sulfate, SDBS) surfactants. The theoretical results agreed well with the erperimental data for SDBS, but not for Dowfrother 250, especially for the initial stage. Reasons for the variation in results are given in the paper.

Jan 1, 2005

By Anitava Ghosh

A computer program has been written to simulate ground vibrations induced by multiple- hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosive charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g.,velocity, attenuation, single-hole input pulse), or by back-calculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties encountered are backcalculating individual input pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shorn to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included, improved input pulse determination and propagation laws, and more detailed verifications with field results are required in order to make the program more directly applicable to practical situations.

Jan 1, 1986

By D. C. Rotherham

The Kidston gold discoveries were originally made about 1907, and by 1934, 1.76 Mg (62,000 oz) of gold had been produced from placer and lode mining of higher grade, most¬ly oxidized gold ore. As mining in the lode ore penetrated deeper, costs increased and the world gold price stagnated. The lode or underground production averaged close to 6.9 g/t (0.2 oz per ton) Au for the 201 kt mined. No mining or development took place from 1934 until 1965. Kidston's high grade ores were exhausted by 1934. From 1965 to 1976, exploration had developed 3 Mt of about 3 g/t (0.88 oz per ton) Au. Placer Pacific acquired rights to the property in 1976 and began a geologic and engineering study of the district. It was clear that the deposit had the potential for becom¬ing a large-tonnage, low-grade producer. However, explora¬tion had to discover the tonnage and grade and engineering needed to solve the obstacles of production costs. Bulk material handling problems were addressed by Placer's wide experience in open pit mining, and the increase in work index accompanying deeper ores was handled by Placer's metallurgists. The matter of power for the operation was solved by engineering studies. These showed that power could be generated and brought in economically. The price of gold also increased after 1976, and this helped in the economic analysis. The Kidston discovery since 1976 is really a combination of good exploration geology and careful engineering plan¬ning that overcame the obstacles presented by ore characteris¬tics and the location of the deposit. The attached paper by Harry Mustard is an extract of his honors thesis and explains the deposit geology.

Jan 1, 1990

By D. W. Fuerstenau, P. C. Kapur

A new method is proposed for measuring the grindability of solids and the energy efficiency of grinding mills. The method is based on a similarity law of fracture mechanics for elastic materials in conjunction with the self- preserving character of the size distributions formed when feed particles are comminuted individually in compression. The single-particle grindability index reflects more closely the inherent resistance of a solid to size reduction than the grindability indices currently in vogue. The performance of grinding mills is evaluated in comparison with the single-particle breakage mode, which has the highest energy utilization or efficiency of all mechanical grinding routes. For a given set of stipulations, the performance index of the commonly used ball mill when grinding dolomite is found m he only 21%. compared to 44% for the high-pressure roll mill, a newly-invented energy-efficient mill. The difference is also reflected in the energy consumed per unit mass offines produced when closed-loop grinding circuits are simulated, which shows that the high-pressure roll mill circuit is invariably more energy-efficient than the ball mill circuit, provided the energy input per pass through the mill does not exceed a prescribed limit. Theoretical upper bounds on the yield of the ground product in a desired size range and lower bounds on the energy investment are calculated from the single-particle breakage mode which has, apart from the highest energy utilization efficiency, a minimum dispersion in size of the comminuted particles. Data on theoretical hounds for seven minerals/ores are presented. It is argued that it is unlikely that a grinding mill can be designed and a comminution circuit constructed whose performance exceeds these bench-mark values.

Jan 1, 1995