Search Documents

Gold cyanide equilibrium adsorption isotherms in the loading range typical of operating carbon-in-pulp/carbon-in-leach plants have been established and the effect of various cations and the presence of copper cyanide species quantified. It was found that the equilibrium loading of gold was enhanced by the presence of sodium or calcium, with calcium having an order of magnitude stronger effect. The presence of copper has an adverse effect on the equilibrium loading of gold. A unified model was developed to predict the effect of sodium and calcium concentrations in solution and the competitive carbon adsorption of copper on the equilibrium loading of gold on carbon. A satisfactory agreement between the measured gold equilibrium loadings and the model results was obtained over a wide range of solution conditions.

Jan 1, 2010

By Ralph M. Stricklen

The need to move large tonnages of slurry has grown as mines have become larger. As existing tailing depositories are filled up, new mines developed, or environmental requirements dictate, it becomes necessary to transport tailing particularly over longer distances. A typical slurry transport system is shown in Figure 1A. Figures 1B, 1C and 1D show sketches of the system auxilliary components: feed box, receiving sump and drop box, respectively. There are two basic types of slurry transport systems, packed flow and slack flow. Packed flow is typified by a pipe running full; slack flow by a launder or pipe running less than full. Slack flow in launders or channels is also referred to as open channel flow. Generally slack flow slurry transportation involves a flow with less than 65 per cent solids, and there is an upper limit on particle size, depending on the slope of the system.

Jan 1, 1984

By Larry Diaz

A single stage ball mill-cyclone circuit was extensively tested for its reactions to step changes in three controllable variables: feed rate, water to cyclones, and water to the ball mill. A series of carefully designed tests are to be carried out in order to determine relationships between the various ball mill and cyclone parameters. Cyclone overflow particle size distribution is to be continuously monitored during the tests using an ultrasonic device. Other circuit variables that are to be measured and recorded are feed rate, ball mill mass flow, cyclone feed and overflow densities, cyclone feed sump level, water flows, etc. Once the circuit performance is defined, two types of grinding circuit control systems will be evaluated: (a) mass flow-based; (b) particle size- based. Results obtained by each approach in terms of feed rate and cyclone overflow size distributions are discussed. The high sensitivity of continuous particle size measurements to grinding circuit disturbances is emphasized.

Jan 1, 1971

By R. Asamoah, K. B. Owusu, G. Abaka-Wood, W. Skinner

The hostile nature of industrial autogenous (AG)/semi-autogenous (SAG) mill operation necessitates the need for robust and reliable online measurements. Mill slurry density is regarded as a critical variable and requires a suitable range for grinding efficiency. In this work, mill acoustic sensing of five different slurry densities (50, 60, 70, 80 and 90 wt.% solids) was investigated using a laboratory-based AG/SAG mill. The results showed that slurry density of 70-80 wt.% solids gave the highest mass of -75μm particles and similar acoustic intensity. The mill acoustical level increased continuously coupled with energy reduction as a function of increasing slurry density, an indication of potential realtime measurement.

Mar 2, 2022

By Peter L. Siems

Humid tropical environments pose many problems for mineral exploration. The problems result from thick lateritic soils, dense vegetation, seasonally heavy rains, deep chemical weathering, few outcrops and thick saprolites. Although geochemical exploration should be potentially a useful technique in these environments, it appears from the scarcity of reports in the literature that insufficient attention has been paid to developing procedures that are specific to the needs of humid tropical areas. For this reason, the authors believe that this account of a geochemical study in a tropical coastal area on the edge of the Brazilian shield is of general interest and importance for potential geochemical exploration surveys in similar areas within the tropics. The objective of the geochemical study was to develop a practical technique of reconnaissance geochemical prospecting for copper deposits in Brazilian tropical coastal lowland areas. In order to achieve this objective, information concerning the secondary dispersion of copper in these areas was required. Consequently, an orientation survey was designed to provide this information. The present account contains details of the geochemical study and the information about the secondary dispersion of copper that was acquired during the course of the orientation survey. Location and Climate The field area is on the Atlantic coastal lowland of Brazil at latitude 13°S. It lies approximately 10 kilometers south of Maragojipe, a city of 15,000 inhabitants; this city is on the western side of the Bay de Todos os Santos about 45 airline kilo¬meters northwest of Salvador. (See Fig. 1) A good gravel road from Sao Felipe to Sao Roque do Paraguay crosses the southern part of the field area. The climate of the area is hot and moist, and is without prolonged dry periods. The mean annual rainfall is about 1600 mm (63 in.) and the greatest precipitation occurs during the winter months of May and June and the summer months of December

Jan 1, 1972

By R. R. Givler

Since the 1860's the good ole days, oil has been nozzle fed to burners under pressure atomizing the oil into droplets -- 1960's has produced vaporized oil that burns oil with the flame color and consistancy of gas -- If you can tell the difference by looking at the flame, gas or oil I?ll buy the lunch. First, we must ask, "Why all the excitement about Blue Flame?" This question is best answered by you after you have studied the principle of operation and see the result. I will attempt to explain both of these so that you can draw your own conclusions.

Jan 1, 1975

By V. N. Kelly

The ability to link geological sections on a graphics screen to form three dimensional geology representation was implemented at Kidd Creek in 1987. This technique affords an opportunity to optimize metal estimation in ore at the Kidd Creek copper, zinc and silver mine, by applying enhanced interpretation methods. On a series of geological sections varieties of ore are outlined. These are linked from section to section to form polyhedra which closely simulate the three dimensional shapes of the different ore types referred to as mintypes. The orebodies are divided into zones, referred to as domains, that approximate the function of variograrns, for which' preferential continuity of mineralization has been estimated for distances in the width, strike and dip directions. These distances define ellipsoidal volumes of influence. The domains are also linked into polyhedra. Both types, coded by ore variety and zone, are mapped into the block model. Tonnage and metal values are calculated for ten-foot cubical cells of the block model by any of several estimation methods under domain control. In estimating the metal grades for a cell the predetermined search ellipse is applied to select only those drill hole assays of the same mintype as the cell designation. Once grade estimations have been determined for the cubical cells comprising the model, a wide range of stored information can be viewed. For example, in plan at any row elevation or on vertical section at any azimuth, as either printed values for the cells or as contoured data. This flexibility is of particular value in checking and refining the geological interpretation to better conform to ore types and grades actually mined. Combined with three dimensional geological modelling, and correctly chosen domains, the use of mintypes implants essential geological control into the system and prevents assays for one ore type from affecting grade estimation in adjacent ore types. The three dimensional geological modelling and block model segments provide information which is effectively applied to the stope design, production, planning and control parts of the system.

Jan 1, 1989

By B. Kolonja

This paper considers simulation of truck dispatching system designs using maximum expected production of the truck-shovel system as the measure of performance. Two methods are utilized, multiple comparisons with the best (MCB) and the combination of MCB and the variance reduction technique known as common random numbers (CRN). These two techniques are compared via simulation experiments. The results show that the combined procedure of MCB with CRN is the superior tool to reduce the total number of replications needed to ensure the specified probability of correct selection over the finite number of designing systems. In this case study, MCB with CRN reduces the variance by 29% and the number of required replications by 48%. Also, the MCB with CRN procedure narrowed the confidence interval by 18%.

Jan 1, 1994

By Patrick B. Kenny

Generally speaking, it is safe to address this conference as a conclave of Engineers, Owners' Agents, Governmental Representatives, and Contractors. As a group, we have assembled here to learn of our compatriots engaged in similiar underground operations throughout the United States and the World. We are here to learn of improved methods, higher technology, and better management. Through the acquisition of this knowledge, we each hope we can improve our own particular services, products and projects. This session is dedicated to a discussion of "Costs". The most apparent reason for a discussion of costs at this level is to expose subjects affecting costs and propose methods to reduce them. From that premise a contractor can identify three areas of discussion: design considerations, contract considerations, and governmental considerations. A fourth area of consideration is an introspective view of the contractor's role in the design construct process. Unnecessary costs and risks attributable to these areas are contributing excessively to ever increasing project and system costs. DESIGN CONSIDERATIONS On April 20, 1977 the Metropolitan Sanitary District of Greater Chicago accepted proposals for the Tunnel and Reservoir Plan on Contract A and Contract B. This letting called for construction of over 33 km (21 miles) of the Mainstream Tunnel bored at 9.75 m (32 ft) to 10.67 m (35 ft.) in diameter. Also included were all the appurtenant collecting and regulating structures. The proposal allowed the

Jan 1, 1979

By Ted D. Johnson

INTRODUCTION The tailing dam is part of the SOHIO L-Bar Uranium Mine and Mill located about 70.8 kilometers (44 miles) west of Albuquerque in northwestern New Mexico. The dam location is shown on Figure 1. The tailing dam is one of the last upstream method dams permitted in the industry. Design and construction aspects of the project, as well as operation and maintenance considerations, are reviewed herein. Since initial construction, SOHIO Western Mining Company and Woodward-Clyde Consultants have developed several modifications and improvements in the dam's operating and monitoring procedures. This work has been done in coordination with the New Mexico State Engineer's Office and in accordance with recommendations in a report done for the Corps of Engineer's Phase I Dam Inspection Report. Modifications and improvements described should be of particular interest to owners and operators of other tailing dams utilizing the upstream method of deposition. The tailing facility was designed for a 10-year life to provide an ultimate storage capacity of 6 1/2 billion kilograms (7 1/2 million short tons) in an area of about 180 acres. A plan view of the tailing dam is shown on Figure 2. The tailing consists of approximately 75% sand size material and 25% fines (material passing the No. 200 sieve). The tailing dam includes a small earth starter dam with raises of the dam accomplished using tailing deposited by upstream method techniques. The starter dam is a homogeneous embankment about 610 meters (2000 feet) long, a maximum height of 12 meters (40 feet) and 2 1/2:1 (horizontal to vertical) upstream and downstream slopes. The starter dam contains an internal drainage system which includes a near vertical chimney drain connected to horizontal finger drains. A typical section through the maximum height of the starter dam is shown on Figure 3. A small confining dam, approximately 1.6 meters (5 feet) high, is constructed beyond the limits

Jan 1, 1980

By G. Hwang, S. Park, H. Kim, J. Choi, P. Seo

"In the mineral processing, clay minerals have negative effects on the flotation of valuable minerals. In this study, we investigated how the floatability of malachite (CuCO3·Cu(OH)2) is affected by presence of the clay minerals in the fundamental aspects. Flotation experiments were conducted by using Na2S and PAX (potassium amyl xanthate), and the floatability of malachite was compared between the cases in the presence and absence of clay minerals. The results showed that floatability was greater in the absence of clay minerals than in the presence of clay minerals and decreased with increasing weight percent of kaolinite under same conditions applied. In addition to examine how clay minerals affect malachite floatability, we conducted flotation experiment with changing clay adding order. The results indeed showed that malachite floatability was affected by clay adding sequence. INTRODUCTION The demand of copper is growing as industrial development increases, but mineral resources are limited. Therefore, studies for Cu oxide flotation are being conducted to improve their recovery(1-3). However the mining industry is well aware of the difficulty in treating copper ores in the presence of clay minerals(4). Clay minerals have unique properties and these properties may affect flotation. In the previous studies, the effect of slime coating of clay minerals on flotation was investigated(4-6). For example, Zhao and Peng (2014), Peng and Zhao (2015), and Arnold and Aplan (1986) found that clay slime coating on chalcopyrite, chalcocite and coal surfaces through the electrostatic attraction reduced surface hydrophobicity and then depressed the flotation. Other researchers have also reported clay minerals have impact on pulp rheology. Especially in the case of bentonite, pulp viscosity increased with increasing amount of bentonite and the higher pulp viscosity have deleterious effect on copper recovery(7, 8). However, these studies only focus on slime coatings and pulp rheological behavior. Forbes et al. attempted to decoupling rheology and slime coatings effect on flotation but this study has limitation that individual role of two clay species either attached to mineral or suspended in bulk solution was excluded(9). Hence, in this study, we aimed to investigating the effects of individual clay (suspended and attached) on malachite flotation."

Jan 1, 2016

By D. W. Smellie

This paper is a review of technological progress in mining geophysics during the past decade. This has been the most significant period in the history of mining geophysics. Among the already existing; techniques, instruments for ground -magnetic and electromagnetic prospecting, were developed that are more, portable and faster to operate. Induced polarization equipment came into widespread use. Airborne instruments of various types became available and were used to survey large areas. Drillhole instruments were developed and have had some use, and it is to be hoped will be used to a greater extent in the future. Two revolutionary new methods, the AFMAG and INPUT, were developed. The wisdom of attempting to cover such a broad field in a single paper might be questioned. There is the inevitable problem that each topic must be discussed very briefly. However, while papers describing individual instruments have appeared, many have yet to be described in the technical literature. The evolution of the ground magnetometer and electromagnetic instruments has not been discussed. It is only recently that a review article has appeared on airborne EM. The existence of review literature on some topics has meant that they are given less emphasis in this review than those topics inadequately covered. It will also be observed that stress is laid on "chose instruments that are generally available to the mining industry rather than those developed by individual exploration companies for their own use.

Jan 1, 1963

By Joseph E. Schiller

As part of the Bureau of Mines research on identification of asbestos fibers, a method was discovered for removing asbestos fibers from water. This report describes this process and its theory of operation. The surface charge of amphibole minerals in potable water was found to be negative, and in common with most other silicate minerals, the isoelectric point of amphibole asbestos fibers lies in the pH range 4 to 6. Magnesia is one of the rare oxides with a high isoelectric point of about 11. The surface of magnesium oxide will, therefore, be positively charged in water at pH 6 to 6, while the electric charge an. amphibole asbestos fibers is negative. Because of the electrical attraction of these oppositely charged solids, it was possible to remove negatively charged asbestos fibers from water by percolating water that contained suspended-asbestos through a porous bed of magnesium oxide particles. A bed of 100/200-mesh MgO was added to a glass tube with a cotton plug. Aqusous suspensions of 1 to 10 ppm cummingtonite asbestos (amosite), crocidolite, and chrysotile were percolated through this porous plug of MgO. Even though chrysotile is positively charged below pH 11, MgO is an effective filter medium for removing it. The highly basic MgO appears to cause the chrysotile to flocculate and attach to particles within the bed. Scanning electron photomicrographs indicated that essentially complete removal of the fibers from water was accomplished. Other materials tested as contact filter media and found to be ineffective or only partially effective were sand, calcite, carbon, diatomaceous earth, and cellulose. Acidic alumina collected amphibole fibers but not chrysotile fibers.

Jan 1, 1980

By M. Moats, J. Young

Short term laboratory cell electrorefining experiments were performed to examine the impact of electrolyte composition, current density and temperature on deposit structure, roughness, and adhesion to 2B mill finished 316L stainless steel. Copper electrodeposits were produced using synthetic electrolytes with thiourea and the continuous addition of glue. Deposit structures were evaluated using X-ray diffractometry. Surface roughness was measured using profilometry and analyzed using scaling analysis. Finally, an internally developed method was used to measure the force required to remove the electrodeposited copper from stainless steel to determine adhesion strength.

Mar 2, 2022

By Y. C. Kim

An alternate development drilling strategy to the one currently in use at the nine was investigated using geostatistics for a portion of the pit. The study area consisted of 4,000' x 5,000' in plan and 1,080' in elevation. The massive orebody, the three-dimensional nature of the problem, and the location of ultimate pit limit in the study area all created some unique problems in devising the development drilling strategy, as compared to the two-dimensional tabular deposits such as coal deposits. Rather than using the confidence interval of the global reserve estimate as the main criterion for development drilling, the confidence interval of short and medium range mine planning blocks was used as the objective. Based on somewhat arbitrarily selected level of confidence, the results from this study showed that a total of 50 DDHs rather than the planned 62 DDHs is sufficient in the study area, if the selected confidence levels are acceptable to the management. This paper also emphasizes the importance of the particular objectives being used in development drilling and how they influence the "optimai" place- ment of the development drill holes.

Jan 1, 1981

By N. R. Hasenmueller, V. Rajaram, R. K. Leininger, D. D. Carr

The content of the paper by V. Rajaram does not fulfill the expectations of the title. But Rajaram submitted the article in October 1983, and he could not have foreseen the numerous developments that would occur before his paper was published more than two years later. Nevertheless, Rajaram failed to mention the interest in oil shale development in southern Indiana beginning in late 1979 and continuing through the present as a result of special financial encouragement of three oil shale projects in May and August 1984 by the Indiana Energy Development Board and the Indiana Corp. for Science and Technology. A session at the 1985 Eastern Oil Shale Symposium in Lexington, KY, Nov. 18-20, 1985, gave the current status of oil shale developments in the eastern United States. Speakers at this session reported on the three Indiana projects. First, Gary D. Aho, Cliffs Engineering Inc., spoke on a feasibility study by Cliffs Engineering and Allis Chalmers for a site-specific pilot plant using the Allis Chalmers process. The plant site is in Clark County, IN, on property of the Midwest Energy Resources Co. The project is funded by $240,908 each from the Indiana Energy Development Board/Corp, for Science and Technology (EDB/CST) and the US Department of Energy (DOE) and $120,454 from the corporate sponsors (total $602,270). Completion is scheduled for mid-1986. Next, Edwin M. Piper, Stone and Webster Engineering Corp., discussed the American Syn-Crude/Indiana Oil Shale Project. This effort followed the completion of two smaller projects funded by the Indiana EDB/ CST: "Testing of Indiana Oil Shale in a Petrosix Pilot Plant" (total funding by EDB/CST at $50,000) and "Assessment of the Petrosix Process for an Indiana Shale Oil Plant" (total funding by EDB/CST at $100,000). The status at the time of the report at the Oil Shale Symposium was that a request for an extension of time for securing nonfederal support had been submitted to the US Synfuels Corp. The proposal included building an 11-m (36-ft) diam retort in south-eastern Indiana to process the New Albany Shale and to produce 366 m3 (2300 bbl) of shale oil per day by the PETROSIX process. The Indiana EDB/CST had contracted with Stone and Webster at $401,100 from EDB/CST and $245,835 from Stone and Webster for activities to advance the project in the negotiations with Synfuels Corp. At the time of the report, this project was the only eastern oil shale proposal that was still on the agenda of the Synfuels Corp. As a result of Congressional action in late December 1985, federal support from the Synfuels Corp. is no longer possible. Finally, Victor H. Carr, Eastern Shale Research Corp., described his firm's project, which is jointly supported by DOE ($227,749) and the Indiana EDB/ CST ($73,850) and is entitled "Feasibility Study to Determine Suitability of an In-Situ Process to Recover Hydrocarbons from Eastern Shale." An area in Scott County, IN, had been chosen, but not a specific 9 x 15-m (30 x 50-ft) site. One burn of a small in situ retort is contemplated as part of the project. Besides these three projects, several reports on shale research were presented. Joseph Damukaitis, American Syn-Crude Corp., reported that a pilot plant using the hydrogenation-extraction (H-E) process (described at the 1984 Eastern Oil Shale Symposium) was 94% built and would go through shakedown with oil shale but would then shift mechanical devices to process coal mine waste. Current status of research on the HYTORT process was then presented by Raymond C. Rex, Jr. Oil shale beneficiation research at the University of Alabama/Minerals Research Institute was reported by R. Bruce Tippin. Scott D. Carter discussed continued research on fluidized-bed retorting of shale at the Kentucky Center for Energy Research Laboratory. Carl E. Roosmagi of DOE, Morgantown, reported on the oil shale research at the Morgantown Energy Technology Center (METC) laboratory. Henry J. Gomberg, Ann Arbor Nuclear Inc., discussed "Radiation Combined with Donor Solvents for Extraction and Up-Grading of Kerogen." Aurora M. Rubel and coauthor Eileen Davis presented results of research at the Kentucky Center for Energy Research Laboratory under the title "The Effect of Shale Particle Size on the Products from the Bench Scale Fixed Bed Steam Pyrolysis of Kentucky Sunbury Shale." Lastly, Maria Rockwell, Technical University of Nova Scotia, presented "Processing and Up-Grading of Low Grade Nova Scotia Oil Shale for Potential Use." A review of shale oil prospects by Gerald Parkinson in Chemical Engineering for Feb. 3, 1986, covers both western and eastern projects and includes a report that the US DOE is funding a few relatively small projects; most of the fiscal 1986 budget of $12 million for shale oil is for fundamental research. Projects include a $3.2 million three-year contract with Hycrude Corp. (Chicago) for development of the HYTORT process and a $1.2 million three-year contract with the University of Alabama's Mineral Resources Institute on beneficiation of eastern oil shale by froth flotation. The report incorrectly states that current projects include a total investment of $466 million in a pair of 18-month technical and economic feasibility studies for proposed projects in southern Indiana. The correct figure is $468,657 [$240,908 for the Cliffs Engineering/

Jan 1, 1987

By William Hustrulid

INTRODUCTION The Idarado mine lies high in the San Juan Moun¬tains on the divide between the Uncompahgre and San Miguel Rivers and consists of a consolidation of a number of old and prominent mining properties through which course some famous and very produc¬tive veins. Among the better known are the Smuggler, Tomboy, Montana-Argentine, Black Bear, Liberty Bell, Virginius, Flat, Barstow, and Japan, as well as many others. Most of these veins have been extensively mined over the past century and in the last three decades the Montana-Argentine and Black Bear veins have been the backbone of the Idarado mine; therefore, the descrip¬tion of the veins is limited to them. Access to the mine is through either the Treasury tunnel, whose portal is below Red Mountain Pass on US Highway 550 at an elevation of 3244 m (10,643 ft), or the Mill Level tunnel entrance 3.2 km (2 miles) east of Telluride, CO, at an elevation of 2761 m (9060 ft). The Treasury tunnel intersects the Black Bear vein 2643 m (8670 ft) from the portal and the Mill Level tunnel intersects the Argentine vein 2179 m (7150 ft) from the portal. Mining is by shrinkage stoping from slusher sublevels. The size of the scope blocks varies somewhat, but the standard size is 67 to 76 m (220 to 250 ft) long and 61 to 76 m (200 to 250 ft) high. The mine ranks either first or second in Colorado in yearly production of gold, silver, copper, lead, and zinc. It is 9.6 km (6 miles) from the Red Mountain plant to the Pandora plant, via interconnecting drifts and raises. There are engineering offices at both plants as a matter of convenience. The Red Mountain plant in¬cludes the company general offices, warehouse, carpen¬ter and machine shops, and mine change room. The Pandora plant consists of the mill and assay office, ma¬chine shops, and mine change room. The flotation mill has a capacity of 1632 t/d (1800 stpd), making a bul¬lion product and separate concentrates of lead, copper, and zinc. HISTORY OF THE MINE The Montana-Argentine vein was first extensively worked by the Tomboy Gold Mines Co., Ltd., a British concern. This company mined the stoped areas above the Ophir level between 1910 and the late 1920s and most of the stoped areas above the 2100 level between 1900 and the late 1920s. Gold was the principal ore metal mined. The area between the Revenue and Ophir levels was mined chiefly by the Revenue Mines Co. between 1900 and 1910. The ore was worked from the Revenue tun¬nel, which portals in Canyon Creek. Gold and silver were the chief metals recovered. The stopes between the 1700 and Revenue levels, as well as some higher stopes, were mined by Telluride Mines Inc. during the 1940s. The Mill Level tunnel was driven by that company from 1945 to 1948. Lead and zinc then became economically more important than the precious metals. In 1953, Idarado purchased Telluride Mines, which merged with the parent company in 1956. The Black Bear vein was first extensively worked by the Black Bear Mining Co. in the 1900s and by the Colorado Superior Mining Co. from about 1914 until snowslides at the mine camp [altitude 3750 m (12,300 ft)] terminated the company's operations in 1924. Leasers operated at intervals until 1934. The Treasury tunnel, formerly the Hammond tunnel, had been started before 1900 and reached the 1646-m (5400-ft) mark early in the 1900s, at which time activity lagged until the late 1930s. In the early 1940s, Idarado extended the Treasury tunnel from its heading at 1646 m (5400 ft) to the Black Bear vein and established a raise connec¬tion with the 600 level, the lowest level in the old mine. Since completion of initial work in the mid-1940s, systematic development of the mine, both in the driv¬ing of new headings and the utilization of older open¬ings, has resulted in the present extensive network of workings. GEOLOGY Introduction The oldest rocks of the area are the Precambrian metamorphic rocks, the Uncompahgre formation which are massive quartzites, some phyllites and slates, and dolomitic or limestone beds. West-dipping Paleozoic and Mesozoic strata lie on the Uncompahgre formation. These units are separated by a major angular uncomformity from overlying, essentially horizontal, Tertiary formations that include the basal Telluride conglomerate and several thousand feet of overlying volcanic rock. Intrusive rocks, mostly Tertiary in age, are common in the area, and are in the form of dikes, stocks, and sills. Dikes are very closely associated with some of the ore veins (Mayer). Description of Veins The Black Bear and Argentine veins range from 0.6 to 7.6 m (2 to 25 ft) in width, but in most places are 1.5 to 2 m (5 to 7 ft) wide. They vary in character from a well-defined tabular structure between sharp "frozen" walls, or gouge seams, to an irregular zone of quartz and quartz-sulfide stringers. Many gouge seams within the veins make the veins blocky and loose. Common gangue minerals in the veins include quartz, pyrite, rhodonite, chlorite, sericite, clay minerals, epidote, calcite, adularia, rhodocrosite, fluorite, and specularite. Quartz constitutes 60 to 70% of the veins and varies widely in character, ranging in color from clear through white, gray, and green, to amethyst. Chlorite, sericite, the clay minerals, and fine-grained quartz are common alteration products of the vein walls and of wall rock fragments in the veins. Epidote is an altera¬tion of the dike or, less commonly, of tuff-breccia. Calcite, adularia, fluorite, and rhodocrosite, which are wide¬

Jan 1, 1982

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts (CCB). Alkaline combustion byproducts are gaining increasing usage for acid mine drainage (AMD) mitigation as research leads to a better understanding of their beneficial applications. Since January 1997, Mettiki Coal has been injecting alkaline flue gas desulfurization material from Virginia Power's Mt. Storm Unit No. 3 wet limestone scrubber into abandoned portions of the active Mettiki Mine.

Jan 1, 1998

By C. E. Capes

INTRODUCTION In the coal industry, ever greater amounts of fine coal must be processed due to the need to crush to finer sizes for impurity liberation in low cost physical cleaning processes. Fine coal processing is a major problem for the industry, both through the cost of disposal of reject fines and through the mining cost of lost coal values. Of the available disposal methods, impoundment has always been the most popular. In many cases, when the coal fines were of sufficient quality, froth flotation and expensive filtration methods were used to recover the coal in these waste streams. The coal fines are not always of a marketable quality, however, and flotation, due to poor yields and difficult dewatering, has always been an expensive and not necessarily profitable process. The oil agglomeration method is increasingly important as a technology for the treatment of fine coal-in-water suspensions. These fines can be preferentially wetted and agglomerated by many different oils mixed with the suspensions. Ash-forming impurities remain in suspension and are rejected when the agglomerates are recovered, for example, by screening. Agglomeration-based methods provide perhaps the only practical means for upgrading extremely fine coal to useful products on a large scale. As with froth flotation, oil agglomeration relies on differences in the surface properties of coal and impurities to effect separation. Whereas flotation be- comes less effective with particles finer than 200 mesh (0.075 mm) or coarser than 50 mesh (0.3 mm), there appears to be no lower limit on particle size for oil agglomeration while particles % in. (3.175 mm) diameter or larger can also be treated, if desirable. In addition to this ability to clean a broader size range of coal particles, oil agglomeration can produce a dense, coarse granular product of acceptable strength and low water content without the need for vacuum or thermal drying. The preferential wetting of solid surfaces by immiscible liquids has been utilized, if not fully understood, for a long time. Indeed Gaudin,229 in tracing the ancestry of froth flotation, refers to a 15th century oil-pulp kneading procedure in which water-wetted particles were freed under water from an oiled mass. An understanding of the physical chemistry involved in such

Jan 1, 1991

By Sebastian Avalos, Julian M. Ortiz

The long-term mine scheduling is the optimal decision on how to extract and process the mining reserves. The resulting plan is mainly driven by economic, metallurgical, and geological factors. Accounting for their uncertainties leads to a robust solution and the feasibility for economic-risk quantification. In this work, we model the spatial uncertainty of grade distributions of multiple correlated elements, by using a multivariate morphing transformation. The result is a set of multivariate geostatistical realizations of the grades, which honor the conditioning data, the direct and cross variograms, and the multivariate statistical distribution, inferred from a set of samples. These models are the input in a reinforcement learning framework, adopted to train a deep neural network that considers the grade uncertainty and leads to an optimum mine plan after training using deep Q-Learning. Mining and processing capacities, as well as economic parameters and metallurgical constraints, are incorporated as the reinforcement learning environment rules. The method is validated on a real deposit, providing insights for future applications.

Jun 25, 2023