Search Documents

By D. C. Ridenour

The pressure system of ventilation with large diameter bore holes has been very effective in the ventilation of two gaseous mines, the Olga No. 1 and No. 2 Mines in McDowell County, West Virginia. The No. 4 Pocahontas Coal Seam on the Olga property lies 580 feet below the valleys. The seam is very gaseous as well as dry and dusty, which makes good ventilation all the more essential. Irregular and often extensive areas of the coal seam have been replaced with impervious shales and sandstones in "Fault" or "Want" areas. The replacement materials have sealed the methane in the coal seam and thus increased the quantity of gas that must be handled as mining is done. Often the No. 5 Pocahontas Seam comes down to meet the No. 4 Seam at the Faults and considerable methane is sometimes released from the upper seam. The factors mentioned, together with the irregular and unpredictable lateral shape' of the faults, result in long narrow stringers of coal that are very gaseous and difficult to mine. So far as the Olga Coal Company is concerned, the most effective ventilation under the conditions outlined has been the use of large diameter bore holes with a pressure ventilation system. The ventilation of a mine can be accomplished in two fundamental ways. The mine atmosphere maybe reduced below atmospheric pressure by an exhaust fan; or it may be raised above atmospheric pressure by a pressure fan. In either case, the coursing of the air is so planned as to have the haulage and traveling ways on intake air. While the majority of the coal mines in the United States, no doubt, use the exhaust system of ventilation, there are several advantages of the pressure system which are extremely beneficial.

Jan 1, 1960

By R. J. Pruett, P. I. Prescott

Ground calcium carbonate (GCC) is used in the paper, plastics, paint, rubber and caulks and sealants industries. The favorable properties of GCC include high whiteness and brightness, low hardness and outstanding rheology in water systems. The quality of calcitic GCC ores, which includes chalk, limestone and marble, is dependent on calcite purity and the nature and quantity of the impurity minerals. Wet and dry grinding are used in the processing of GCC. Ore processed by optical sorting, flotation and/or particle-size classification has higher brightness and lower abrasion characteristics. GCC markets are a function of the product's properties, purity and cost.

Jan 1, 1997

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985

By Louis J. Jansen, D. E. Ranta

Techniques utilized to incorporate geological data in computer modeling and ore reserve estimation have undergone considerable evolution during the past fifteen years. Computer analysis and evaluation of two precious metal deposits are presented as examples of innovative computer techniques developed at Asarco. The first is a gold deposit occurring in a steeply dipping Precambrian greens tone sequence. The second is a manto-like manganiferous silver deposit occurring in a relatively flat sequence of Late-Paleozoic sediments. In both deposits, four sub-horizontal zones of geological influence are evaluated.

Jan 1, 1992

By C. Caceres

Fibre reinforced shotcrete in combination with other types of support systems is becoming the leading support method for underground excavations, especially those present in low quality rock masses. Sudden or rapid ground support failure can expose workers to safety hazards, damage to equipment and others resulting in production interruptions that will impact the cost of operation. Knowing the peak and post-peak strength characteristics of the support system over time are of major importance. Round Determinate Panel Testing of fiber reinforce shotcrete is the primary test used by the mining industry to determine strength characteristics; however, the tests are costly and significant manpower is required in a mine environment to build, store, handle and test the panels. For these reasons numerical modeling can result in an effective method to produce realistic results. This paper examines the strength characteristics Round Determinate Panel tests and its ultimate application in underground excavations, using Itasca?s three dimensional particle flow code (PFC3D).

Jan 1, 2010

By Richard D. Harvey

Petrographic properties of carbonate rocks are useful guides to the utilization of these rocks in SO2-scrubbing systems. High porosity and fineness of grain are thought to be the principal properties that contribute to high dissolution rates of the rocks in the scrubbing liquor. Lake marls and chalks are the major types of carbonate rocks that have these properties. Lake marls are composed mainly of equant grains of calcite (mean grain size generally less than 4 microns) weakly agglomerated in- to larger, porous particles. The marls commonly consist of 80 to 90 percent CaCo3 as calcite and aragonite. Impurities are, for the most part, quartz silt and organic matter. The average pore volume for samples of lake marls (1- to 1.2-mm particles) is about 0.50 cc/g, which corresponds to a porosity of about 57 percent. The mean size of pores in these marls is generally between 1 and 2 microns in diameter. Surface areas of lake marls range from 0.8 to 6.8 m2/g. Chalks have grain sizes and shapes similar to those of lake marls, but they generally have smaller amounts of quartz and organic matter and minor amounts of clay minerals. Pore volumes differ from one chalk formation to another; the 1- to 1. 2-mm particles average about 0.20 cc/g, which corresponds to a porosity of about 35 percent. The mean diameter of pores in chalks tested ranges from 0. 15 to 0.76 micron. Surface areas of chalks range from 3. 2 to 20. 1 m2/g. In the United States lake marls are restricted largely to Pleistocene- age sediments that occur in the states around the Great Lakes. Chalk and chalky limestones are restricted mainly to the Upper Cretaceous and Tertiary strata in the Kansas-Nebraska-Colorado area and in the south- eastern states, from Texas to Florida. Results of laboratory tests of the relative dissolution rates of samples at pH 6 and 44°C indicate that, in addition to many lake marls and chalks, oolitic aragonite, pelecypod shells, and carbonate waste sludges from certain industrial plants also have high dissolution rates.

Jan 1, 1974

By D. Tao

Coal is a major source of energy in the U.S. and more than 51% of the electricity used in the country is generated from coal. Coal cleaning prior to combustion is necessary and often accomplished using wet physical processes at coal preparation plants to remove impurities such as ash, sulfur, mercury. However, the resultant clean coal product still contains a significant amount of impurity due to the fact that impurities are not well liberated from coal particles ranging from several millimeters to inches in size at which wet cleaning processes take place. A cleaner coal product can be obtained if a cost-effective dry process is developed to further clean pulverized and thus better liberated fine coal at the power plants prior to its combustion. The benefit of such a process is a significant reduction in the cost of expensive post-combustion chemical cleaning processes such as flue gas scrubbing employed to meet the stringent environmental air quality regulations. In this study, a novel rotary triboelectrostatic separator (RTS) was investigated for its application to dry cleaning of fine coal samples acquired from the power plants in the state of Illinois. The pulverized fine coal contains well liberated ash and pyrite minerals and is an ideal feed to the triboelectrostatic separator for further cleaning without the use of water or any chemical reagents. The proprietary rotary triboelectrostatic separator (RTS) is characterized by an innovative high efficiency rotary charger, charger electrification, laminar air flow, and specially designed electrodes. Compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator offers significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range, etc. Testing with several fine coal samples has demonstrated that this technology can significantly reduce ash content with a process efficiency similar to or better than froth flotation. Important process parameters such as charger rotation speed, injection and co-flow rate, feed rate were investigated for their effects on separation performance.

Jan 1, 2010

By B. A. Kennedy

The instrumentation, monitoring, and prediction of a major slope failure at the Chuquicamata mine are described. In December 1967, pre-existing tension cracks on the south end of the east wall of the Chquicamata mine began to open. Various forms of instrumentation were installed for continuous monitoring. These systems included tension crack stakes, crack extensometers, linear extensometers, tape and transit lines, sliding wire contacts, and a seismograph. From the information obtained, the failure date was accurately predicted some five weeks before failure, enabling the mine to reroute truck and rail access; hence, causing a minimal mine shutdown of two and one-half days and preventing any injuries to persons or damage to equipment. The shape and form of the sliding mass are analyzed, as are the possible modes of failure.

Jan 1, 1970

By D. F. Symonds

INTRODUCTION Dense medium processes have been used to separate coal and ores for over a hundred years. In fact Sir Henry Bessemer first patented a process in 1858. In recent years, their importance relative to other gravity dependent processes has increased. This is particularly true in the coal industry where over 60% of all preparation plants operating in 1984 in North America (1) contained either dense medium vessel or cyclone circuits. In addition, the stringent product quality demands of the consumer, together with increases in mining costs, dictate that the cleaning circuits be both predictable and efficient. Dense medium systems are the most predictable and efficient of all gravity- dependent processes. The majority of the text of this chapter will be concerned with dense medium applications as they relate to the coal industry. However, the techniques and calculation procedures can be applied, in general, to all non-coal minerals (such as diamonds, marginal iron and lead-zinc ores and gravel) which take advantage of a difference in specific gravity between the saleable product and the reject. The object in dense medium cleaning is to produce a liquid whose effective specific gravity is between that of the concentrate and the reject. In which case the lighter product will float to the surface and the heavier product will sink to the bottom. Unfortunately, this simple process becomes complicated by the following practical necessities: (a) collecting and removing the float and sink products from the medium without disturbing the free settling effects; (b) maintaining and controlling the specific gravity of the medium; (c) separating and reclaiming the medium once the products have left the separating vessel; and (d) separating finer sized particles which take longer to fall through the dense, and often viscous, medium. As a result of the last issue (item d) two main types of dense medium separators have evolved: dense medium vessels and dense medium cyclones. Dense medium vessels are essentially large baths through which the dense medium flows at a relatively slow velocity. The lighter products float to the surface and are carried out of the vessel by the medium flow. The heavier products sink to the bottom of the vessel and are physically transported out either by means of a conveyor (usually a chain conveyor) or a rotating, lifting arrangement (Figure 1). They generally

Jan 1, 1986

By G. S. Austin, L. A. Brandvold, J. Renault

A series of tests were run on soil samples collected near the site of a Socorro, NM lead smelter that was abandoned more than 98 years ago. Three 30.5- x 30.5-m (100-X 100-ft) squares provided 13 samples each. As described in Part I (this issue), each sample was divided into seven splits according to particle size. A mineralogical examination of the fine-size fraction of Pb-contaminated soils failed to reveal crystalline Pb compounds. These authors conclude that Pb is present as amorphous phases or is adsorbed on the surfaces of soil particles. Site vegetation contained elevated Pb levels that increased with increasing Pb amounts in the soil. However, the biological absorption coefficient (BAC) indicates that some of the site's Pb is unavailable, or the plants are able to limit their uptake. Of the vegetation tested, rabbit bush showed the greatest increase of Pb levels in its roots, whereas levels in creosote were highest in the foliage. In cactus, the Pb levels varied. The amount of Pb due to dust incorporated in plant tissue is almost negligible compared to the amount absorbed through the plant vascular system.

Jan 1, 1994

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

6.1 INTRODUCTION A surface structure will suffer damage when the additional stresses induced by ground deformations associated with surface subsidence, plus the original stress introduced by construction de¬sign, exceed the strength of the structural elements. In this con¬text, there are two methods available for preventing and control¬ling surface structural damage: one is to strengthen the structure and the other is to design the mining operations such that ground deformations at the structure site can be reduced to an acceptable level. Mining operations include panel layout and mining tech¬niques. These methods are detailed in this chapter. It must be noted that most prevention/control methods men¬tioned in this chapter are used in the countries where the reference papers are cited. In the United States, the coal operators are not required to take those measures mentioned in this chapter. Some of the methods described in this chapter cannot be implemented with¬out changes in the current mining practice as permitted by laws. In addition cost of implementing those methods are not considered here. 6.2 PANEL LAYOUT As shown in Figs. 2.9, 2.10, and 2.11, permanent ground deformations in a subsidence basin mainly concentrate near the edges of the underground opening, and can be divided into four zones. A structure located in different zones will be subjected to different types and magnitudes of ground deformations. In laying out the panels, Table 5.1 and Figs. 2.9, 2.10, and 2.11 could be taken into consideration. Attempts could be made to avoid placing the structure on a location where the ground deformation to which that structure is sensitive is at its maximum. Therefore rational design of the panel is the simplest way to reduce structural defor¬mations. Panel design involves the determination of panel dimension, panel edge location, direction of face advance, and use of yield chain pillars. A. Panel Dimension Since longwalls in the US employ a multiple-entry system, where rows of chain pillars are left unmined, subsidence over those chain pillars is usually smaller. Therefore, whenever possi¬ble, the panel dimension could be designed such that a major structure or structures are over those unmined chain pillars, be¬tween adjacent panels, or some distance beyond both ends of the panels. At the center of the supercritical final subsidence basin, a structure will not be subjected to any final or permanent ground deformations. In order to create such a condition, the panel width must be such that the structure will be located beyond the major influence zone of the final subsidence basin, the minimum dimen¬sion of which must be: [ ] where L is the width or length of the final mined out gob, t is the width or length of the structure to be protected, h is mining depth and [ ] s is the angle of full subsidence. B. Panel Edge Location Wherever there is a permanent panel edge, there are large ground deformations induced on the surface on both sides of the permanent panel edge. Therefore whenever possible the panel di¬mension should be designed such that the permanent panel edges could be located in the areas with the least impacts. In terms of permanent edge location, it is best to eliminate any permanent panel edge under a structure or groups of structures. If this cannot be done, the panel should be lengthened to reduce the number of permanent panel edges, or narrower multiple panels advancing in the same direction in a staggered manner could be employed. If the structures are located in Zones II and III, the longer dimension of the structure must be parallel to the nearest perma¬nent edge (Fig. 6.1). But in Zone IV, the longer dimension should be tangential to the corner of the permanent panel edge. If the structure is inclined to the permanent panel edge, it will be sub¬jected to twisting and shearing. C. Direction of Face Advance The direction of face advance should be parallel to the long axis of the structure. But if the structure is to be located at or close to the center of the final subsidence basin, the direction of face advance should be perpendicular to the long axis of the structure. Careful choice of the direction of multiple face advance is the most effective way to reduce structural deformation and thus dam¬age. This applies the principle of overlapping and cancellations of ground deformations, due to multiple face advance, at the right time and at the right intensity, e.g., opposing tilts, concave and convex curvatures, tensile and compressive strains are induced simultaneously on the structure to be protected by two or more faces. D. Use of Yield Chain Pillars In US longwall panels there are generally two or three rows of stiff chain pillars between the panels. The combined width of the chain pillars ranges from 100 to 350 ft(30 to 107m). depending on mining depth. In general, surface movement above the chain pil¬lars after the panels on both sides have been extracted is much smaller, as compared to that in panel center. Thus in order to create critical or supercritical width of opening and eliminate sur¬face bumps over the chain pillars, yield chain pillars may be em¬ployed (Jarosz and Karmis, 1986). However if yield pillars are to be used, it must be designed such that it yields totally right after the panels on both sides have been extracted. Unfortunately cur¬rent yield pillar design techniques cannot predict when and how much it will yield. In summary, whenever possible attempts could be made to lay out the panel in such a way that surface structures are located above chain pillars between panels or above solid coal beyond both ends of the panels. In those areas the surface structures will most likely be unaffected, or if affected, the damage is so minor that no remedial measures are necessary. 6.3 CONTROLLED MINING TECHNIQUES Several mining techniques are available for reducing the sur¬face ground deformations of specific types. Regardless of tech-

Jan 1, 1992

By T. J. Jr. DeMull, F. G. Miller, J. P. Matoney

For some time a need had existed in the minerals processing field for a relatively efficient separator that would treat high tonnages of particles in the intermediate size range, i.e., those particles too large for froth flotation and too small for conventional gravity-type separa¬tors. Among those devices developed to meet this need are the centrifu¬gal specific gravity separators. These devices employ centrifugal acceleration to assist gravitational acceleration in separating light¬density minerals from heavy-density minerals. In the category of centrifugal specific gravity separators are the heavy-media centrifugal separator and the water-only cyclone. The two major centrifugal heavy-media separators, i.e., the heavy-media cyclone and the DynaWhirlpool, as well as the water-only cyclone, are discussed in terms of: design features, operating variables, operat¬ing data, and flowsheet design criteria. Examples of plant applications are given in the field of coal processing as well as the processing of other minerals such as iron ores, potash, and tin. Finally, the subject of the staging of centrifugal separators and their use in combination with other separators is discussed. PRINCIPLES For coarse sizes of minerals, efficient specific gravity separations have been possible for many years with open-bath vessels using the natural settling velocity or buoyancy of the particles. These bath ves¬sels process ore by utilizing micron-size solid particles suspended in the slurry fed to the separator. The inclusion of these particles in the slurry increases the effective density of the separating fluid to allow particle separations to be made at densities greater than that of water. However, if vessel size is to remain within economical limits, the particles processed in the bath vessel must have high settling rates in a IG gravitational field. Because of this requirement, heavy¬medium bath vessels are usually restricted to processing +V4-in. sizes. To extend efficient specific gravity separation to smaller sizes, the gravitational acceleration of particles is replaced by centrifugal acceleration. The settling of a small particle in a fluid in a centrifugal force field is similar to that found in a static bath except that the acceleration due to gravity, g, is replaced by a centrifugal acceleration where v, is the tangential velocity at radius r: V=kdm(P-P,), V'. (J) µ In more practical terms where the particles settle in a suspension of finer particles comprising the heavy media and with an effective suspension density p" V = kdm' (P P ) . v'. (2) U r To date the most effective use of this principle has been obtained with devices that rotate a liquid or suspension within a stationary enclosure in order to create centrifugal force. Cyclones are the most common devices used for this purpose, because they generate centrifu¬gal forces far greater than the force of gravity and therefore not only have high capacities but can treat finer sizes than bath-type vessels can. The two main types of cyclones used by industry are the heavy-media cyclone and the water-only cyclone. Also quite widely used is the DynaWhirlpool, which, though based on the same princi¬ple, differs in design from the conventional cyclone. HEAVY-MEDIA CENTRIFUGAL SEPARATORS Like the bath vessels, the heavy-media centrifugal separators em¬ploy media composed of micron-size particles suspended in water. However, the centrifugal force generated in these separators accentu¬ates the difference in settling rate between particles of different density and thus makes possible separations of finer size particles than can be treated in bath vessels. The two most common heavy-media centri¬fugal separators are the heavy-media cyclone and the DynaWhirlpool. Heavy-Media Cyclone Although cyclones were originally developed for use as classifiers or thickeners, it was later found that they could also effectively serve as heavy-media separators.63. 64, Design Features Fig. I I is a schematic of a typical cyclone developed to serve for any one of the following purposes: as a classifier, thickener, or specific gravity separator. The cyclone consists of a cylindrical section joined to a conical section, usually having an included angle of between 14° and 25°. Feed enters the cyclone tangentially through an orifice attached to the cylindrical section. The overflow orifice is located in the base plate of the cylindrical section. The vortex finder, a tube attached to the overflow orifice, extends into the cyclone from the base plate of the cylindrical section. The underflow orifice is located at the apex of the conical section. As some medium together with mineral particles is fed through the feed orifice, a vortex with a hollow air core extending from the overflow to the underflow orifice forms in the cyclone while hollow spray discharges form at each of these orifices. Under the influence of the centrifugal force, high specific-gravity particles move through the medium to the wall of the cyclone and descend in a spiral flow pattern to the underflow orifice. Those particles in the feed stream, lower in specific gravity than the feed medium, follow the major portion of the flow to the center of the core where they are caught in the high-velocity upward central current and are carried out through the overflow orifice. Fig. 12 shows a family of curves that illustrates how materials of varying specific gravity are recovered by a cyclone. Since the specific gravity of the medium is 1.40, the particles of 1.40 sp gr actually act as part of the medium and, regardless of the particle size, split between the underflow and overflow of the cyclone in proportion to the volume split of the medium. Particles higher in specific gravity than 1.40 are recovered in the underflow of the cyclone at increasing rates as the difference in specific gravity increases and the particle size increases. Particles lower than 1.40 in specific gravity are dis¬charged through the overflow orifice at increasing rates as the specific¬gravity difference increases and the particle size increases. However, all the curves originate at the fluid-flow ratio point for the finest particles of any gravity. The fluid-flow ratio is defined as the ratio of the rate of fluid flowing from the underflow to the rate of fluid

Jan 1, 1985

By Erich U. Petersen

Chemical zoning studies of mineralization can be useful in guiding exploration efforts. They permit one to determine the limits of mineralization and to correlate mineralized intervals in drill holes. Fahlore minerals are well suited for zoning studies because they are common minerals found in a variety of deposits, exhibit chemical diversity, and record the chemical evolution of migrating hydrothermal fluids. Zoning information in the form of metal ratios preserved in fahlore minerals was used to determine ore body limits in the Orcopampa precious metal system, Peru, and to correlate between multiple ore horizons in a sediment hosted massive sulfide (SHMS) currently under investigation. The current generations of electron microprobes provide the most efficient, accurate and economic way to analyze the tens to hundreds of sample required to successfully describe and use zoning information at the mine scale.

Jan 1, 1991

By T. Vandergrift, J. Sturgill, W. Gerhard, J. Carrick

As surface minable coal is depleted, many operators look to high-wall mining to extend reserve life. Recent advances in highwall mining equipment have greatly improved productivity, clean coal recovery, and attainable penetration beneath the highwall. Somewhat lagging have been systematic design approaches for ensuring web pillar and overall highwall stability. This paper presents an overview of the design, planning, and field performance of a multiple-seam highwall mining application in southwest Wyoming. The safety and efficiency obtained to date is attributable to the careful geotechnical and operational planning described herein. Field confirmation of performance and suggestions for improvement are also discussed.

Jan 1, 2004

By Colin J. Douch

New Zealand has been a significant producer of gold for over a century. Total recorded production is over 850 tonnes. There were three major periods of production: the first and biggest was between 1860 and 1880, the second was between 1895 and 1920 and the third was between 1930 and 1945. After 1945 gold production fell continually until 1980 when the major upward adjustment in gold price led to renewed interest. There have been important new developments in each of the known gold-rich areas: Westland, Otago and Coromandel and exploration for gold in these areas and in previously unprospected regions has reached unprecedented levels. In Westland over 140 gold processing plants are each producing between two and six ounces a day from low-grade placers. A major gold dredging operation will soon be producing over a tonne of gold annually and other new dredges are proposed. There are still vast reserves of gold-bearing gravels in Westland and prospecting is continuing to reveal new resources. In the Reefton area there is renewed interest in gold-bearing quartz reefs which were the source of over a million ounces of gold between 1900 and 1951. New large opencast reserves are now defined.

Jan 1, 1988

By Jiang Su, Michal Uhrin

"The use of composite linings, consisting of permanent sprayed primary and secondary linings with a sandwiched spray applied waterproofing membrane is expected to improve efficiency and reduce lining thickness, but it also brings complex primary-secondary lining interaction. This issue is further complicated by the uncertainty regarding the long-term behavior and parameters of the sprayed concrete–sprayed membrane interface.This paper aims to address this issue by presentation of a series of numerical analyses of a typical shallow SCL tunnel in soft ground with a range of design assumptions on the interface behavior: (1) compression only; (2) compression and tension; and (3) compression, tension, and shear.The results demonstrate that the assumed interface behavior has a significant impact on the primary-secondary lining interactions. A design approach of ignoring the tension and shear bond at the interface may not be conservative particularly for serviceability. This paper explains the rationale behind these conclusions and discusses the implications for design.INTRODUCTIONSprayed Concrete Tunnel Lining SystemsSprayed concrete linings (SCL) have been used in conventional tunneling for decades. However, details of SCL systems may differ to a large extent depending on ground conditions and specific tunneling methodologies.In hard rock conditions, for example, drill and blast excavation is typically supported by rock bolts and sprayed concrete (NGI 2014). Such tunnels are usually designed fully drained and the above-mentioned support elements considered permanent without the need for a further inner liner. Therefore, there is no structural interaction between separate lining shells to consider.In conventional tunneling in the European Alps, a double shell lining is typically utilized, consisting of an outer (primary) sprayed concrete lining and an inner (secondary) cast-in-place concrete lining, separated by a waterproofing system. The primary lining normally includes rock bolts and may include other support elements. The waterproofing system is usually based on a plastic membrane and a geotextile fleece. The tunnel may be designed fully or partially drained or fully undrained. Although there are two structural lining shells interacting, investigation of such interaction is generally irrelevant to designers because the primary lining is considered only temporary (fully sacrificial in the long term). An overview of reasons for this assumption is given, for example, by Lemke (2014). The secondary lining is designed to resist all foreseeable loads on the tunnel. The primary lining may, in reality, interact structurally with the secondary lining during the life span of the tunnel. However, since the secondary lining design must cover all possible (extreme) scenarios, investigation of such interaction does not bring any value to the design."

Jan 1, 2016

By Vasiliki Founta, Andrew J. Whittle

"This paper describes the development of a 3D finite element model for predicting ground movements caused by construction of 7.1 m diameter twin bored tunnels for the Crossrail project in London using Earth Pressure Balance (EPB) machines. The model uses the commercial FE code, Plaxis 3D, to represent the face pressure, conical shield, grouting process and activation of precast segmental concrete lining systems through a set of boundary conditions that advance through the soil mass along a prescribed trajectory. Soil behavior is described using the Mohr-Coulomb soil model with input parameters calibrated from laboratory element tests. The analyses focus on the performance of the EPB tunneling machines in greenfield conditions beneath Hyde Park, where the tunneling occurs within deep layers of relatively uniform London Clay. The model predictions are in good agreement with surface and sub-surface vertical settlements measured at a well-instrumented section, but tend to overestimate the measured lateral displacements towards the tunnel. Ongoing studies are focused on the role of soil behavior and the approximations in FE model predictions of tunnel-induced ground deformations. Introduction Since their introduction in the 1970’s, closed-face Earth Pressure Balance (EPB) machines have become widely used for soft ground tunnel construction. The EPB design relies on a screw conveyor system to regulate the pressure of the excavated soil/spoil within the head chamber and hence control stability at the face of the machine. One of the key design issues in the application of EPB machines is to establish how control parameters, including the advance rate, face pressure and grouting processes (used to compensate for the tail void at the rear of the shield and to infill gaps between the precast lining rings and surrounding soil) affect and/or control the far-field ground movements. For closed-face systems, short-term deformations are associated with ground losses at the face, overcutting and ploughing of the shield and poor control of grouting in the tail void; while long-term deformations can occur due to consolidation and creep within the surrounding soil (and are closely connected to the seepage boundary conditions;e.g., Laver & Soga, 2012). The control parameters for advancing the EPB machine can have a significant effect on the magnitude and distribution of the far-field deformations. Therefore, analyses of the ground response to tunneling require accurate modeling of the soil stratigraphy and constitutive behavior as well as the construction process. Finite element (FE) methods have been used to simulate tunnel construction since the early 1980s, but only a few studies involved three-dimensional modelling of mechanized tunneling (e.g., Finno and Clough 1985; Bernat and Cambou 1999; Swoboda and Abu-Krisha 1999; Dias et.al. 2000; Melis et.al. 2002; Kasper and Meschke 2004; Möller 2006). In order to get a better understanding of the effect of the construction process and soil properties on the development of the ground deformations more comprehensive models of tunnel excavation and tunnel support are required in order to capture the 3D nature of mechanized tunneling and the effect of construction parameters such as advance rate, face and grout pressure."

Jan 1, 2016

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019

By L. M. English

A basic model was developed to help assess methane control needs for the longwall mining of coal in gassy areas. Rather than depending on reservoir and rock mechanical theories, it uses an empirically determined gas emission rate as an input, and it operates on the assumption that, within a specific region and zone, gas emissions will be relatively equivalent for uniform incremental volumes of gob created by mining. The computer program divides longwall panels into segments, keeps track of the face advance and generates emission rates and volumes for both the entire panel and for individual zones within the panel by summing values for all undermined segments. This model can aid in the determina¬tion of the number, size and location of vertical wells or other methane-control applications that are needed for gob gas control.

Jan 1, 2000

By J. A. Dos Santos

"INTRODUCTION Dramatic reduction in energy use and environmental impact can be achieved with sandwich belt high angle conveyors that serve as the vital link in any IPCC (In-pit Crushing and Conveying) system. These high angle conveyors are not new at all, but have not found wide use in IPCC systems where they can realize the greatest advantage. Reduced energy consumption and environmental impact, with IPCC systems, was already realized in the 1970s. With the bulk material haulage limited to conventional open trough conveyors the most direct path out of the open pit was precluded, requiring low angle spiral ramps and/or deep slots and/or tunnels through the high wall of the open pit. These excavations, to accommodate the low angle limitations, represented undesirable impact on cost and on the environment. Against this backdrop, a major study in 1979 sought to develop high angle conveying systems that could continuously haul the mined bulk material directly out of the pit, along the high wall – the shortest distance between the two end points. Between 1979 and 1982, that study developed sandwich belt high angle conveying systems that utilized all conventional conveyor equipment including smooth surfaced rubber belts that could be continuously scraped clean. These systems had all of the positive features of conventional conveyors but overcame the angle limitation. By hugging the bulk material between two belts, the material’s internal friction could be developed to facilitate conveying at any high angle up to 90 degrees (vertical). After an intense testing period (about one year) on the first large scale prototype system, commercialization began in 1983 with the installation of a 60 degree incline system at a western United States coal mine, elevating 2000 t/h of coal to a train load out system. It did not take a long period of scrutiny and acceptance before this high angle conveyor found use in the most rugged requirements of an IPCC system. This was only the second commercial sale, and after more than 150 commercial installations, it remains arguably the most significant high angle conveying system. In 1984, a copper mine in Serbia, already using pit perimeter crushing and conveying, decided to move their primary crusher deep into the pit and to use a sandwich belt high angle conveying system to elevate the ore continuously, directly out of the pit, along the high wall to the pit perimeter where it then transferred to a conventional conveyor for the remaining haul to the plant. The system had significant features including 2000mm wide belts that elevated 250mm coarse ore, at 4000 t/h, over six 15-meter high benches for a total 90 meters of net lift. The system was able to reduce the truck haulage fleet by ten 200 ton trucks realizing great cost savings, zero emissions to the air and greatly reduced traffic congestion in the pit. The system operated successfully until 2002 when the mine shut down. Many successful sandwich belt high angle conveyors followed with the current count of commercial installations at more than 150. Despite the great success with this system, its use has not been repeated as part of an IPCC system."

Jan 1, 2018