Search Documents

By F. Robert Hollo

Programmable controllers have achieved remarkable acceptance over the relatively few years since their introduction. They provide some unique advantages over conventional relay and solid-state logic, which they often replace. Programmable controllers are discussed in both conceptual and functional terms, followed by an exploration of their applicability to material handling tasks with particular emphasis on conveyor systems.

Jan 1, 1973

By Y. B. He

The effect of the stability and rheological properties of magnetite dense medium on the separation performance of a 6" dense medium cyclone (DMC) is studied with the use of fine density tracers. The tests in which different size fractions of magnetite are used to prepare the dense media reveal that at low medium densities (<1.5 s.g.), the best separation is achieved when using the magnetite with intermediate particle sizes (du3.2=18 11m). At medium densities above 1.5 s.g., however, it is beneficial to use coarser magnetite. With the fine magnetite dense medium, an increase in medium density results in a decrease in separation efficiency. With the coarse magnetite, an opposite trend is observed; the separation efficiency is improved with increasing medium density. An accurate cutpoint control is critical in gravity separation. The cutpoint shift for coarse feed particles is found to decrease with increasing medium stability (density). It assumes values close to zero in a highly stable fine dense medium. When the size of the treated particles is small (<0.5 mm), the cutpoint shift is mainly determined by medium rheology. With increasing medium density, a continuous increase in cutpoint shift is observed.

Jan 1, 1993

By Neal Retzer, Adam Bedell, Nick Cioffredi

The first wagon trail across Loveland Pass was built in 1869 thus starting the struggle between the Colorado Rockies and interstate travel. The 1st Pioneer Bore underneath Loveland Pass at the Continental Divide in Colorado was attempted between 1941 and 1943 and was abandoned due to ground conditions at the Loveland Fault. Construction on the nearby Eisenhower Tunnel began in 1967 and was completed in 1973. Numerous challenges associated with tunneling, including at 11,000 ft were overcome. The purpose of this paper is to summarize the history of investigation and construction challenges associated with the Eisenhower Tunnel to celebrate its 50th anniversary.

Jun 13, 2023

By R. L. Zick

The High Density Sludge Process was originally developed by Bethlehem Steel Corporation for use on acid mine drainage and diluted waste pickle liquor discharges requiring continuous chemical treatment systems. This work began in the early 1970s and was first put into practical use around 1973. To date there are approximately 15 operating systems which have been installed on mine drainage in the United States, and another 10 systems worldwide. Dense Sludge is an innovative and improved method for treating acidic metal bearing streams in a manner which minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge recycle process which forms particles that have a low affinity for water, unlike conventional metal hydroxide solids which contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations which combine with calcium ions in lime based treatment systems to form gypsum crystals. The physical form of this gypsum is radically altered when the Dense Sludge process is utilized compared to the form generated in conventional lime treatment systems. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. Slides No. 1 and No.2 show scanning electron micrographs of conventional and densified sludges illustrating these differences. The magnification used was 300X. The dense sludge particles settle faster, dewater more readily, are more easily pumped, and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered.

Jan 1, 1998

By C. Zhou, J. Srednicki

Electronic systems have been increasingly used in underground mines to improve mine safety. These electronic systems emit electromagnetic (EM) energy which can adversely impact the performance of other electronic systems nearby and thus should be characterized. Researchers at the National Institute for Occupational Safety and Health (NIOSH) characterized the magnetic fields emitted from devices that can potentially interfere with the performance of proximity detection systems (PDSs) and compared the emission levels of these devices to the susceptibility of PDSs. In this paper, we present our measurement results pertaining to this effort. Particularly, magnetic fields emitted from the different orientations of a powered air purifying respirator (PAPR) and two lite trackers are evaluated based on the RE101 protocol specified in the MIL-STD-461G standard. The results show that both devices emit strong magnetic fields which strongly depend on the orientation of the devices. At some frequencies, the maximum emission levels from the two devices exceed both the emission limit given in MIL-STD-461G and the maximum magnetic fields that a PDS can withstand without a failure. The results and findings in this paper can help the mining industry better understand electromagnetic interference (EMI) underground and provide critical scientific data that support mining-specific recommendations to address EMI-related challenges.

Feb 1, 2023

By C. P. Miller

In a study of the usefulness of geochemical and biogeochemical prospecting for nickel made about two years ago, approximately ten localities, representing several different types of nickel occurrences were sample, and about 1500 samples of plant and soil were collected. This report will briefly cover the data and results for two areas, and s summary of guides for prospecting.

Jan 1, 1959

By L. Rudolphy, P. Tähkiö

"The cPlant is a modular flotation plant which has been designed to minimize capital expenditure and risk. The plant is based on a number of standard modules, for both flotation and ancillary equipment, which can be configured to give the required flowsheet for the ore being treated. All of these modules can be rapidly deployed and erected onsite, minimizing not only engineering time and site preparation but reducing the time taken to get the plant up and generating revenue. Given the paradigm shift in flotation circuit design that has been employed in the cPlant it may allow smaller, previously uneconomic deposits to be exploited and create a more cost efficient upgrade route for existing plants. This paper introduces the cPlant and presents a case study comparing EPC cost and development timing of a cPlant against a traditional flotation circuit design. INTRODUCTION In the development of any mining project the cost associated with process plant engineering, equipment procurement and installation can affect the financial viability of a project. This is of special significance for smaller scale mining projects which perhaps don’t have the mine-life or revenue generation to justify the payback on a modern processing facility. Listening to customer feedback and understanding the challenges that small to mid-sized projects can face lead Outotec to the development of the cPlant. Modularization of mineral processing plants isn’t a new idea with a number of examples being reported in literature for gravity gold (Cabot, Trudel and Cabot, 2001; Gray et al., 2006), dense medium separation (September and Abate, 2006) and even hydrometallurgy (Saario et al., 2013). All these plants have been developed to try to improve on the traditional economics associated with fixed processing plants. Using standardized modules to construct a plant reduces engineering time and design costs which can both be beneficial to the outcome of a project. In addition the modular nature of the plant lends itself to transport to remote sites and rapid installation with only minimal site preparation required. A plant of modular design also has several other advantages over its conventional cousins. Firstly it is relatively easy to expand by duplicating existing modules. Secondly the modules can be treated as building blocks for the process and rearranged if a change in conditions requires flowsheet adjustment. Thirdly, there is potential to disassemble and remove the modular units at the end of the mine life. The ability to easily disassemble, re-pack and transport the plant to a new location not only is important to the long term environmental footprint of an operation but can also be seen as a bonus to an operator that has a number of small ore deposits. If applied in this way modular plants have the potential to create a whole new operating model for previously unviable ore deposits."

Jan 1, 2016

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By Wolfram Schnabel

Recently Lurgi has succesfully commissioned Peru&apos;s first direct reduction rotary kiln at SIDERPERU?s Chimbote works. The order included comprehensive engineering services and supply of special equipment to modify three existing cement kilns according to the SL/RN process. The kilns were cut to 62m length and installed with a slope of 2.5%. A new heating system, including shell burners, was supplied and inlet and outlet ends of the kilns completely renewed. Figure 1 shows the kilns after modification.

Jan 1, 1981

By Russell G. Hood

Rock bolting or anchoring are methods of stabilization which are not being fully utilized in California and probably in other parts of the world due to lack of understanding of the principles, or due to poor results in actual installation. The problem is greater in California because so much of the rock is either soft or badly fractured and broken. Almost any recognized type of rock bolt or anchor will perform successfully is hard, fresh rock, but the problems become many-fold when working in decomposed granites, shales, soft sandstones or other soft, highly-broken rock. There has been an enormous amount of research by manufacturers, consultants, private organizations, and governmental agencies on rock bolting. It would be impossible to discuss all the methods and philosophies of rock bolting in this paper. Therefore, with the indulgence of the experts, I will give only a very generalized coverage on rock bolting techniques. However, My main purpose is to point out some of the problems of rock bolting in soft rock.

Jan 1, 1967

By Krawiec Alfons

The threat of rock bursts along with the danger from methane gas and coal dust explosions belongs to particularly dangerous phenomena in Polish pit-coal mines. This phenomenon results mainly from the physical-mechanical properties of the rock mass as well as the geological-tectonic structure of the Upper Silesian Coal Basin. In the postwar years in Polish coal mining thanks to a multi- directional activity, a decrease of rock bursts and their effects has been noted. For example, the number of rock bursts reported in 1965 amounted to 71 in comparison to only 23 in 1974. The ratio of rock bursts calculated for 100,000 tons of coal extracted from rock bursting strata amounted to 0.08 in 1965; however, in 1974 it amounted to 0.023 /Fig. 1/. These results were obtained in face of a continually growing potential threat from rock bursts caused by the systematic increase of extraction from rock bursting strata, exploitation at gradually greater depths along with the extension of exploitation into deposits enclosed in different types of pillars and other parts of deposits surrounded by workings. Despite the achievements of science and mining practice in this field, this threat has not yet been fully studied and controlled as it should be, As a result, research on preventing rock bursts is being continually widened in Poland. This research has a complex, multi-staged and long-range character. Theory, laboratory and field work in the mines are working on a solution to the problem.

Jan 1, 1976

By G. V. Henderson

Large reserves of high calcium limestone have been outlined in the Redwall formation at Nelson, Arizona. Geologic mapping, core drilling and shallow seismic refraction studies have outlined more than 100 million tons of high quality, chemical and metallurgical grade limestone in the Mooney Falls member of the Mississippian Redwall Limestone. Well developed Karst zones in the Redwall were delineated by field mapping, seismic profiling and core drilling. Development of large reserves of high quality, thick beds of limestone near the present mine and rail facilities was the basis for the current mine and plant expansion. When completed in 1978 the planned 1800 Tpd production will represent the largest lime operation in the Western United States.

Jan 1, 1978

By R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al (III) and flotation collectors. It was found that the presence of Al (III) is necessary for good flotation of the organism whether or not Pb(II) is present when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8 and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al (III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminoproprionic acid is used as collector good flotation occurs at about pH 4 without the addition of Al (III).

Jan 1, 1990

By Evan J. Owen, Virginia T. McLemore

There are tens of thousands of inactive mine features in 274 mining districts in New Mexico (including coal, uranium, metals, and industrial minerals districts). However, many of these mines have not been inventoried or prioritized for reclamation. Many of these mines have existing mine wastes, generated during mineral production, which could have potential for critical minerals, especially since the actual mineral production was generally for precious and base metals and not critical minerals. The purpose of this project is to characterize and estimate the critical mineral endowment of mine wastes and “beta-test” USGS sampling procedures. This project is important to the state of New Mexico because critical mineral resources must be identified before land exchanges, withdrawals or other land use decisions are made by government officials. Future mining of mine wastes that potentially contain critical minerals will directly benefit the economy of New Mexico. Possible re-mining of mine wastes could clean up these sites and pay for reclamation. Furthermore, this project will include training of younger, professional geologists and students in economic and reclamation geology by the PIs.

Feb 1, 2024

By Edmund H. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence - the total absence of noise except for ones own breathing and scuffing of boots on the bottom. An underground mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working on the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur. But excessive noise is a health hazard. In recognition of this fact, our Congress included noise exposure as a part of the "Coal Mine Health and Safety Act of 1969". As Fig. 1 indicates, allowable noise exposure is established by specifying a time duration permitted at different noise levels. This is the well known "Walsh-Healey" criteria which governs noise exposure in many industries.

Jan 1, 1977

By Donald Babbitt

In 1971, during the planning and design stages of a $300 million expansion, the Iron Ore Company of Canada Ltd. through its Engineers, Canadian Bechtel Ltd., came out with a preliminary request for two (2) 10,000 LTPH belt conveyor scale systems. These Systems were to provide weighing accuracies within 2.5% of the iron ore pellets and concentrates in transit on two (2) 72" wide conveyors from the stockpiles to the ships. Each conveyor system would be fed by a rail mounted bucket wheel reclaimer, with the conveyed material moving directly to the ship loaders with no inter- mediate surge and/or storage bins between the stockpiles and the ships. The bucket wheel reclaimer discharge rates would vary from 0-9600 LTPH in cyclic periods, with the periods varying from 1-5 minutes - dependent on the level of the reclaim buckets in relation to the stockpile as well as the slewing rate of the reclaimer. There would be frequent interruptions for bucket wheel repositioning (laterally and vertically), changing ship holds, and trimming ship holds. These frequent zero flow conditions, approximately 500 per 150,000 ton ship, could last 1-5 minutes. In addition, the conveyors on which the scales were to be mounted would be over the water and subject to the wind and cold of Northern Quebec. These Systems would be in use 350 working days of the year and would load 30,000,000 LT/yr. (An average of 90,000/working day).

Jan 1, 1975

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V, 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicated that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

May 4, 2023

By A. H. Farazi, C. Quamruzzaman

The freezing and subsequent solidifying of unstable, weak (sands, silts and clays) and/or wet soil to form a desired-shape frozen barrier around a construction area are possibly the main features of the freezing method for shaft sinking. The barrier, along with strengthening the soil, provides a dry environment to ensure sustainable subsurface construction work before placing a permanent lining. The freezing method requires the installation of freezing pipes in boreholes around the construction area and the circulation of chilled salt water through these pipes and has long been a proven technique for dry shaft sinking through unstable and water-bearing seam around the world. As removing heat from the ground is the main feature of the method, an efficient thermal design of the freezing process is mandatory to ensure success of the shaft sinking operation. This applies to both the sustainability and economy of the intended structure. The design presented in this paper is aimed at figuring out the heat-removing ability and operating time of the refrigerative equipment using some simple formulae. The authors adopted a theoretical approach to determine the quantity of heat to be removed from the ground. The amount of energy for the equipment was found to be greater than that for freezing, which proved the validity of the design. The active freezing period was calculated to be 121 days. The authors followed the structural design of the freezing process they proposed in their previous work (Farazi and Quamruzzaman, 2013). Though the first coal seam in the coalfield was encountered at a depth of approximately 352 m in the subsurface, the target depth for cooling and freezing was decided to be 162 m. The formation demands extra care to nullify its risk of the temporary structure collapsing and water rushing in (Farazi et al., 2012). Discussion on the determination of refrigerative equipment parameters was excluded from the scope of this work.

Jan 1, 2014

By J. Stachurski

Flotation tests were carried out on 6 coal samples of different rank as well as their oxidized samples. A mixture of diesel oil and alcohols was used in these tests. Surface oxidation caused a distinct decrease of the flotation recovery with some improvement in the grade The reduction in the recovery increased with increasing the concentration of the oxidizing agent. The floatability of low rank coals was affected by oxidation to a higher degree than medium and high rank coals. The recovery size curves of oxidized samples mere similar in shape to that of non-oxidized coals.

Jan 1, 1990

By Gary B. Glass

In 1997, 92.3% or 235.7 Mt (259.8 million st) of coal produced in Wyoming came from the Wyodak coal zone in the eastern Powder River coalfield. The mined portions of the zone consist of one to three beds of coal with an aggregate thickness between 15 and 33.5 m (50 and 110 ft). The thickest expression is 61 m (200 ft). The delivered coal from this zone averages 0.33% sulfur, 5.12% ash and 19.98 MJ/kg (8,590 Btu/lb.). This coal zone occurs at or near the top of the Paleocene Fort Union Formation, which is overlain by the Eocene Wasatch Formation. There is also production from two coalbeds in the lower portion of the Wasatch at the southern end of the basin. Production of coalbed methane derived from the Wyodak coal zone is currently an estimated 289 Mm3/a (10.2 billion cu ft/year). This production is occurring west and downdip from the coal mines and is increasing each year.

Jan 1, 1998