Search Documents

By Robert C. Freas

The Northeastern United States is the most highly urbanized region in North America. It is also an area with a tremendous appetite for stone products. Within this context limestone has truely become an "urban ore". Its uses extend from traditional aggregate markets to lawn and garden, archetectual, chemical, agricultural, industrial, and environmental applications. This paper looks at both the occurance and uses of limestone in the northeast, and briefly examines changing patterns in consumptive use.

Jan 1, 1985

By Jacob L. Mathis, Todd Tharpe, Jonathan Steflik, R. M. True

In June 2022, Louisville MSD completed a 6.5 km (4-mile), 6.1 m (20-foot) finisheddiameter CSO conveyance and storage tunnel system located along the Ohio River in downtown Louisville, Kentucky. During construction, the Ohio River Tunnel alignment was expanded 2.4 km (1.5 miles) into areas where natural gas was detected. Without delaying construction, the project team developed and implemented a natural gas risk mitigation strategy to safely excavate the tunnel via TBM and install concrete lining. The risk mitigation strategy included the installation of gas-vent borings, increased tunnel ventilation, retrofitting tunneling equipment for “gassy” operations, and modifying the project specific HASP.

Jun 13, 2023

By James S. Browning

The Mineral Resources Institute of The University of Alabama conducted research on the removal of sulfur from coal using a combination of gravity concentration and flotation methods. The research utilized the gravity and centrifugal force capabilities of the Humphreys spiral to remove part of the pyritic sulfur and ash. Flotation of the Humphreys spiral coal concentrate removed additional sulfur and ash to yield products that conform to Federal air quality standards for sulfur oxide emissions. The clean coal products recovered by the combined process contained 7.7 to 8.0 percent ash, 0.12 to 0.16 percent pyritic sulfur, and 0.78 to 0.96 percent total sulfur. Pyritic sulfur rejection by the process was about 95 percent. In addition to obtaining good recoveries of high quality coal the tests demonstrated that the pyrite in the wastes could be isolated as enriched flotation products by the combined gravity - flotation apporach. Pyrite concentrates analyzing 25 to 33 percent sulfur were recovered. Potential benefits of the pyrite flotation step are recovery of a product of possible market value and the elimination of the pyrite from the waste ash which could be a potential acid water problem when impounded.

Jan 1, 1981

By M. Westerstrand

It is known that the water chemistry of the process water during ore refinement can affect product quality, such as iron pellet strength. The main objective of this study was to quantify the amounts of major elements, such as Ca, Mg, Na, S and Cl carried by process water and by magnetite grain surfaces to the end product, iron ore pellets made from magnetite ore from the Kiirunavaara Mine in northern Sweden. In addition, the amount of colloids (0.22µm ? 1kD) in the process water was examined by ultrafiltration. The amounts of various elements sorbed to the magnetite surfaces were estimated by leaching with Milli-Q water, MgCl2, NH4-acetate and Na-acetate. Total dissolved solids were between 1,446 and 1,775 mg/l, dominated by Ca, S, Na and Cl (89%). The colloidal fraction was less than 3% for major ions. For Ca and Mg, sorption to magnetite surfaces was a much more important transport mechanism for the pelletizing process than evaporated process water, but for Na, Cl and S process water was an important carrier.

Jan 1, 2010

By J. Gustavson, E. Mallard, F. Pirkle

The Sales Comparison Approach to estimating the value of a mineral property must always be attempted1 . In addition to other parameters, the approach depends heavily on the availability of transaction data. The consideration for the mineral property must be in form of cash, cash equivalent or other consideration. In other words, “What dollar amount did the property sell for?” Mineral properties are generally real estate, albeit frequently buried deeply under the overlying surface real estate, unless the property may be a quarry. In some states, transactions must be recorded in county courthouses, and the sale consideration must be included. In such cases, the appraiser’s job is made easy. In other locations, the sale considerations are withheld in the courthouse data; but occasionally a local transfer tax is collected and recorded. Again, the appraiser’s job is made easy by back calculation with knowledge of the legislated transfer tax percentage. The worst problem occurs when the consideration for a mineral real estate sale is totally withheld. That may occur in so-called nondisclosure states. A recent map2 of ten non-disclosure states in red is shown below. For the full color code, please refer to the footnote

Mar 2, 2022

By N. K. Dumakor-Dupey, G. B. Sakyi-Addo, K. J. Bansah

"Artisanal and small-scale mining (ASM) occurs in many countries around the world, and provides a source of livelihood to many impoverished local people in areas where it occurs. This paper reports the role of female participants and reasons why they engage in ASM. Field visits were made to 12 ASM sites located in the Tarkwa Mining District of Ghana to conduct interviews with male diggers and female participants. It was observed that over 100 women between the ages of 18 and 50 participate in ASM for survival. They engage in ASM largely because they have no alternative employable skills and income sources. These female participants depend on ASM to sustain the lives of their dependents. INTRODUCTION Artisanal and small-scale mining (ASM) conventionally involves use of rudimentary tools (such as picks, shovels, chisels and hammers) to exploit precious minerals and metals from the ground. It has been a major source of livelihood to many impoverished local people for more than a century. In many instances, it is the only source of income to indigenous people who have no alternative employable skills. The World Bank estimated that more than 100 million people around the world benefit from ASM which largely occurs in developing countries in Asia, Africa, Oceania, and South and Central America (World Bank, 2013). Cobalt, which is used in lithium-ion batteries to power cellphones, laptop computers, and electric vehicles, is largely produced by artisanal miners in Congo (The Washington Post, 2016). In Sudan, ASM is a significant contributor to the national economy, accounting for about 85% of total gold extracted yearly from 2010 to 2015 (Ibrahim, 2015). Also, according to the Embassy of Sierra Leone in Washington DC, USA, 90% of mineral export in Sierra Leone can be attributed to thriving artisanal diamond mining in the country (Sierra Leone Embassy, 2016). In Ghana, the ASM sector was recognized by government as a multimillion industrial activity, and through a series of initiatives, it was legalized by promulgating the Small Scale Gold Mining Law of 1989 (PNDCL 218). Presently, artisanal mining is widely practiced in two forms: licensed (registered), sometimes referred to as formal ASM, and unregistered (informal or illegal) operations, popularly called “galamsey”, a name believed to have been derived from “gather and sell” by ancient miners who could not communicate in the English language with European/British miners. The ASM sector in Ghana, like other countries, has seen a rise in female participation over the years. A report by the International Labour Organization (ILO) indicated that women account for about 15% of total workforce in ASM in Ghana, and up to 50% in Africa (ILO, 1999). Other researchers have also estimated women participants in ASM to be between 30 and 70% in Africa (Hinton et al., 2003a; Hinton et al. 2003b; Hilson, 2002). Presently, there is no reliable data from Ghanaian authorities on number of females engaged in ASM. However, data obtained from 15 ASM sites suggest that at least 40% of the employees are women. It is expected that a similar trend exists across ASM operations in Ghana."

Jan 1, 2017

By Jamal Rostami, Omid Frough, Wei Hu

Characterizing the abrasiveness of soil/rock and the allowable wear of hard-facing products in various conditions is a critical factor in selection of the best material for certain applications related to drilling and excavation in mining and construction industries. The Soil Abrasion Index test machine at Colorado School of Mines (CSM) is one of the recently developed unique systems capable of testing soil/crushed rock abrasion under various conditions, such as dry, wet, and saturated settings. It is also capable of testing the performance of various types of hard-facing materials in a given geo-material. This paper studies the wear properties of different hard-facing materials in various crushed rocks from a surface mining operation in the iron range region of the USA. The hard-facing materials include regular and hardened steels and six different specialized hard facings, based on chromium carbide. The soil/rock include a standard sand and two rock samples from the surface mine. Fourteen abrasion tests were conducted, where the weight loss of each hard-facing material was measured over timespans up to 1 h of testing. The results show the distinct performance differences between the steels with 17 HRC and 43 HRC hardness and the hard-facing products for this application. The results show the possibility to evaluate the abrasiveness of different rocks at a mine or construction site and the performance of various hard facings in similar working conditions. This is a practical solution for selection of the cutting tool or reinforcement of bucket lips and truck beds for comparison of relative wear life between different wear-resistant materials.

By Osvaldo A. Bascur, J. P. Kennedy

Companies have installed powerful desktops for their personnel and instrumentation and control systems in their plants. These desktops are, in many cases, connected to a company intranet. Still, process engineers have to obtain their data manually. Engineers use process calculations from manually calculated averages from the plant; field operators collect equipment data on log sheets; and maintenance engineers collect critical information on log sheets. All of this information resides in individual machines. What are the strategic tools that will enable collaboration between them? How can operators, engineers, and managers access plant information to proactively increase their effectiveness in process troubleshooting, plant debottleneclung, aligning with business strategic and customer demand, satisfying environmental and safety regulations, developing capital projects, and implementing control strategies? A nonintrusive environment at the desktop is required to provide the process information to these workers. How can value be added to MS Windows technologies with the legacy systems at a minimum cost? There is no straight answer; however, there is a proven framework to leverage the large investments in new technologies. Objects and components are changing the way everyone relates to their computer and networks. Three examples will be described to demonstrate paradigm change. Today, process engineers can access data at the required level of detail for analysis of critical process variables at their desk or remotely. 1. Process Troubleshooting and Analysis: The engineer can develop an inferential calculation, trigger a process advisor to deter- mine the behavior of the units for the last day, and get the population of a set of batches (heats, blocks, rolls, sheets, etc). 2. Process Control and Optimization: The engineer can connect to a process simulator at steady state or a dynamic simulator of the process to evaluate new control strategies or process unit line-ups and use the process simulator as a process observer for fault diagnosis. 3. Collaboration with Accounting and Maintenance: The engineer can review reconciled data and the process mass balances, suggest maintenance cleaning or recalibration of flowmeters, and evaluate key control performance of all advanced controls.

Jan 1, 1999

By K. Yatsunami

NKK has developed a new cold bonded pellet process. The features of this process are; 1) it is a continuous process with 10 hours curing. 2) Products can be used as materials for various metallurgical furnaces. 3) Various kinds of slag are used as binders if necessary. 4) The quality of products is excellent. The pilot plant completed in 1981 is now being successfully operated. We are also constructing a commercial plant at our Niigata works. We produced cold pellets containing carbon as material for ferroalloys (Si-Mn), by pilot plant and used them in furnaces. Consequently, considerable economic advantages were obtained.

Jan 1, 1984

By I. R. M. Chaston

Abstract. This paper puts forward the concept of 'radial' plant layout where all crushing, milling and treatment operations are preferably concentrated in one central area and these separate stages are connected by radiating conveyors to and from outside storage areas. This system is contrasted to the more customary system of 'linear' plant layout where the crushing, milling and often the treatment operations follow one after the other in separate buildings. The radial system simplifies and improves contral and supervision to a very considerable extent and can lead to a form of continuous plant operation with the separate sectors shutting down in succession for necessary maintenance while maintaining the overall plant operation. The paper is illustrated with example: from past and recent diamond treatment plant practice in South Africa which demonstrate the reduction in plant labour achieved by this system. Previous objection to this type of layout on the grounds that it inhibited plant expansion are shown to be unwarranted. Radial Layout for Increased Treatment Plant Productivity A great deal of time and trouble is spent by highly qualified and experience( metallurgists in developing the right treatment process for a given ore. This process is then often expressed in a treatment flowsheet of the type shown in Fig. 1 which shows a typical diamond plant. This flowsheet, when completed, is commonly handed over to the mechanical engineers who then design the layout of the equipment indicated on the flowsheet and produce the working drawings upon which the detailed construction of the treatment plant will be based. It is an unfortunate fact that the tedious and time-consuming juggling of equipment and inter-plant transportation is often left to hard-working draughtsmen who, however capable' in their field, lack practical experience in the day-to-day operation and maintenance of the treatment plants they design. As a result many plants have been produced which, while they satisfy the requirements of the flowsheet with minimum capital requirements, cost far more than should be necessary to op¬erate and maintain. It is often possible to change individual items of equipment which do not achieve the performance required of them, but it is usually extremely expensive to change the basic layout of the plant if this should be found to be unsatisfactory. It should therefore be recognised that great care and attention should be spent on consideration of the basic layout of any treatment plant and that the views of both designers and operators should be fully regarded before settling upon the inevitable compromise dictated by the varying requirements of process-engineering and economics. It is unfortunate that this important subject receives such scant regard in the standard ore dressing text books and hand-books, being usually dismissed in a few paragraphs.

Jan 1, 1977

By R. W. Bruce

The normal practice for processing complex sulphide ore has been to grind with steel balls and/or rods in steel mills before flotation. Little thought had been given to the effect of grinding media on flotation selectivity of copper-lead -zinc ore until 1960 when Rey and Formanek(1) published their experiments on sphalerite floatability after grinding in a porcelain mill with ceramic pebbles. The studies by Rey and Formanek had a pronounced effect on the milling of copper-lead-zinc ores in Canada and possibly throughout the world at a time when autogenous grinding was creating a great deal of interest. The impression was created, and possibly still exists with some mill men, that grinding an ore in the absence of steel will result in a loss of selectivity between copper, lead and zinc minerals. This is in spite of the fact Rey and Formanek's experiments showed that the "naturall floatability" of sphalerite was not apparent after grinding in a porcelain pebble mill in an alkaline pulp.

Jan 1, 1976

By James E. Lawver

During the past century, the Florida Phosphate Industry has established an enviable record of innovative technology in nearly all aspects of mining and beneficiation. A notable exception is the lack of technology to improve the present practice of storing waste clay in earthen dams. The rule which has been adopted by the Department of Natural Resources states, "Since storage of clay wastes for long periods of time interferes with expeditious reclamation and since above grade storage of clays takes otherwise useful land out of production and raises potential health and safety problems, below grade storage and rapid reclamation techniques are encouraged." The two waste products from the beneficiation plant are clay slimes (-0.1 mm in size) and sand tailings. The sand tailings do not present a problem since the tailings rapidly dewater to a dry weight of about 100 pounds/ft3 and make good land fill. By contrast, disposal of waste clay slimes is a formidable task. The basic problem is simply that the waste clay not only dewaters very slowly, but also that the ultimate solids content is very low and in most cases the volume of the clay greatly exceeds the available volume of below ground storage of the mined land.

Jan 1, 1984

By R. Bryce, T. J. Doughty, K. Stoll

Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Ca6Al2(SO4)3(OH)12•26H2O Ettringite readily precipitates in high pH water and by doing so, removes sulfate from impacted waters. The SAVMIN process, piloted in South Africa, is one method to produce ettringite. In this process, aluminum hydroxide is the aluminum source. The Cost Effective Sulfate Removal (CESR) process is similar to SAVMIN, but uses a proprietary aluminum source instead of aluminum hydroxide. Outotec and Veolia also have their own versions of the process using their specialized process equipment. TWC patented a version of ettringite precipitation using metallic aluminum as the aluminum source for ettringite formation. The benefit of using aluminum metal is that no additional ions are added to the process. At high pH, the raw aluminum corrodes in water causing hydrogen gas generation as the water is chemically reduced. This reaction is shown below:

Jan 1, 2019

By Nikhil Dhawan, Shrey Agrawal, Ashwini Kumar

The current study investigates sericite clay as an alternative source of potash and alumina. The alumina and potash content in the sericite is approximately 35 and 10%, respectively, compared with 50–55% in bauxite ore. Muscovite and illite phases are stable, and direct leaching is found to be ineffective. Here, planetary ball milling was performed, which provided dissociation of stable phases to relatively reactive phases. The milling led to a five-fold increase in the surface area, resulting in enhanced leaching kinetics even at low acid concentration. The statistical design obtained optimal conditions of 8 h of milling followed by leaching in 1.73 M HCl at 75 °C, yielding 82% alumina extraction in precipitate with 85% purity in γ-alumina form and 63% potassium dissolution in sylvinite phase. The yield of the precipitate was ~65–68%, and the acid leach residue contained primarily silica.

By S. G. Britton

"Strategies to improve performance in mining production, maintenance and mineral processing operations have evolved over time from straightforward time studies of individual machine performance in the 1960s-1970s to more sophisticated and better focused statistical and financial tools that have emerged in the 1980s-1990s. These newer strategies fall under the broad descriptive category of operational excellence.Operational excellence is the term that embodies a number of performance evaluating strategies, the most popular and relevant to mining include the following:• Six sigma for addressing errors within mining or milling process and work standards.• Lean manufacturing to optimize organizational and operational performance through continuous improvement.There are other strategies that can be applied as well and this paper is not focused on a review of the pros and cons of any one strategy. However, the common threads in these strategies embody the expectation that expected results from these efforts can be quantified and that value will positively benefit the targeted work process, organizational unit, equipment deployment or time schedule when applied to it as part of continuous improvement efforts.The priority for proceeding with any one or more of these efforts is based on the calculated net value of the required resources to make the change versus the estimated value gained. The practice is identified as the value mapping process.This discussion summarizes the value mapping process methodology used at a mature uranium mine and mill in northern Canada to work through the myriad of potential improvement efforts available through the operational excellence process for continuous improvement."

Nov 1, 2016

By C. I. Basilio

The mechanisms involved in the adsorption of modified thiol-type collectors on sulfide minerals have been investigated in the present work. These collectors belong to the broad classes of thionocarbamates, thioureas, thiophosphates and thiophosphinates. They differ significantly from the traditionally used thiol-type collectors, such as xanthates and dithiophosphates, in terms of structural features that involve either the introduction of an additional oxygen donor or the alteration of electron densities on donor atoms. Electrochemical studies suggest that the adsorption of these classes of collectors is probably the result of a coupled reaction of the EC-type, involving an initial electron transfer step (E), followed immediately by a chemical reaction (C). Thus, the overall adsorption process is controlled by both the E, and pK of the system. The role of structural features in changing the interaction of the donor atoms with sulfide minerals is also discussed.

Jan 1, 1991

By C. E. Golson

Modern concrete technology emphasizes the basic qualities required of an acceptable aggregate: it must be clean, sound, homogeneous, and of a size gradation resulting in a concrete of the desired physical qualities at a minimum cost. In the case of coarse aggregates, crushing, scrubbing, and screening will usually provide the required material, although beneficiation is often necessary in order to eliminate unsound or deleterious fractions. Beneficiation is also applicable to fine aggregates,( but the processes most often employed are washing, classification, and dewatering.

Jan 1, 1959

By William Lodding

That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Thus Mackenzie (1) and Bartha (2) reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding, and existing strain may be released by the same process, as shown by Holt et el. (3) All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze by the use of thermal analysis some effects produced in grinding. In differential thermal analysis (DTA) one measures all thermal changes occurring in a substance during heating or cooling. Chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and in thermal conductivity, strain release, etc. By thermo gradmetric analysis (TGA) on the other hand only chemical changes involving weight loss or gain are recorded. Similarly gas evolution analysis (GEA) will register only reactions involving gas evolution, including water vapor, and oxidation-reduction. By performing two or all three of these thermal methods of thermal analysis simultaneously and on the same specimen one can separate the different effects registered and by difference evaluate their magnitude.

Jan 1, 1966

By J. L. Roll

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) and the regulations promulgated for that "Act" have resulted in changes to surface mining operations in order to comply with the stringent federally enforced reclamation requirements for prime farmland. In many instances the operator has modified surface mining operations to meet the prime farmland requirements through changes to mining equipment operation, addition of new equipment targeted for reclamation or the use of totally different mining techniques. The major challenge to mine operators has been how to use existing mining equipment to meet the requirements of the "Act." Freeman United Coal Mining Company opened the first new large surface coal mine in Illinois following passage of the "Act." The Industry Mine, located near Macomb, Illinois started mining operations during March of 1982 and was required therefore, to meet all of the requirements of the "Act" including prime farmland restoration. At the Industry Mine a shovel and a cross-pit bucket wheel excavator (wheel) are used for overburden removal and the wheel is addition- ally utilized to assist in reclamation operations. The wheel mines the subsoil thereby elliminating scraper placement of that subsoil and the attendant compaction problems with scraper placed subsoil. The wheel is used to convey topsoil stock- piles from the highwall to the mined overburden in order to lessen scraper traffic and possible compaction on the graded overburden during top- soil removal and replacement. Close control of the operation of the wheel yields more uniform wheel spoil ridges which then require less grading prior to topsoil replacement.

Jan 1, 1986

By S. K. Kawatra

The use of inferential particle sizing for a closed wet grinding circuit control has been practiced for several years. This paper presents a review of some inferential sizing equations developed for pilot and industrial plants using regression analysis. An analytical development is then presented showing how the general inferential sizing model arises from the nature of the classifier model. The relation between the general sizing model and the individual equations is then discussed.

Jan 1, 1982