Search Documents

By Mike Lewis

"Descending several stories down a metal staircase into a shaft spanning a quarter city block -- soon to become Roosevelt Light Rail Station in Seattle, WA -- visitors are greeted with four perfectly round, precast concrete-lined horizontal holes leading deep into the earth. The sound of water trickling out from a small drainage trough can be heard over the faint echoes of construction within. Upon entering, the light is dim, but the air is clear with barely a dust particle flowing through the sunbeams. This type of air quality is only accomplished with diligent controls, and JCM Northlink, the company in charge of building the Northgate Link Extension Project, is taking those measures seriously.Commissioned by Sound Transit, JCM is a joint venture of three companies: Jay Dee Contractors, Frank Coluccio Construction Co. and Michels Corp. The tunnels JCM constructed are intended to provide fast, reliable underground rail service, as well as relieve one of the region’s most congested traffic areas. The $440 million project will connect the Northgate, Roosevelt and University District neighborhoods north of Seattle to the downtown corridor and SeaTac airport further south.The scope of this project includes excavation for two light rail stations, boring of two parallel 5 km- (3.3-mile) long light rail tunnels in six runs and the construction of 23 cross passages. Begun in 2014, Sound Transit estimates that crews excavated more than 382,000 m3 (500,000 cu yds) of soil and installed 7,352 precast concrete tunnel liner rings during the shaft construction and boring phase. Now that tunnel boring is complete, JCM is in the process of constructing the cross passages, which act as maintenance areas and escape routes for passengers. Throughout the entire process, the company has utilized atomized mist to control particle emissions.“Our dust control needs change at every phase of the project and don’t go away until the project is fully complete,” said a JCM safety representative. “We found that different dust suppression technologies were needed at different intervals, but atomized mist seemed to fulfill our needs at every step.”"

Jan 9, 2017

By L. Barry Phelps

The application of an open-pit Materials Handling Simulator (OPMHS) to analyze mine planning and scheduling problems in large surface mines is discussed. The mine chosen for this application employed a large stripping dragline working in tandem with a shovel-truck haulback system for removing overburden. Large bottom-dump trucks were employed behind a coal loading shovel to transport the exposed coal out of the pit. Specifically, the current operations and the recommendations for short term and long term improvements were simulated on OPMHS. The effects of changing the operating parameters of the equipment on the total system were evaluated. Several alternatives were also studied for the best use of the existing equipment if the current operating parameters could not be improved upon. The results of the application are discussed.

Jan 1, 1978

By Eduardo Poltronieri Trés, Anderson Denadai Thomazini, Rodrigo Boyer Fernandes, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Maycon Athayde, Rossano Augusto Pilon Nunes

The fundamental importance of comminution by high-pressure grinding roll (HPGR) technology to efficiently increase the particle surface area lies in lower energy and water consumptions for iron ore pellet feed production. This study compared the ball wet milling process with the innovative HPGR processing technology for hematite-goethite ores. Green-pellet balling and induration processes were simulated on the bench and pilot scales.

By QUANWEN PU, Yonggang Wei, Bo Li

With the advancement of industrial science and technology, more and more catalysts are used. The spent catalysts produced are solid waste products, which cause environmental pollution if they are not treated. At the same time, the spent catalysts contain some precious metals such as platinum in concentrations that are often higher than in their ore resources. Therefore, the recovery of valuable metals in spent catalysts is a hot research topic at present. However, due to the complex structure of the spent catalysts, dealing with them is a lengthy process. The first step of recovery, enrichment of the spent catalyst, becomes particularly important. In this paper, a pressure solution method is investigated for this purpose, in which the alumina carrier is dissolved and platinum is enriched in the leaching residue.

By Marshall D. Himes

The Pima mine, 39,000 ton per day copper mine, is located 17 miles south of Tucson, Arizona. The mine is in a sequence of Paelozoic and Mesozoic sediments striking east-northeast and dipping southeasterly intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian(?) dolo¬mites, limestones, and sandstones have been altered to talc-silicate skarn, marble and quartzite. The overlying Mesozoic Triassic(?) clastic sediments have undergone some recrystallization and hydro¬thermal alteration. The clastic metasediments are divided into three distinct lithologic units, lithic arenite, arkose, and inter¬bedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar and quartz, with or without sericite and chlorite). The porphyry has undergone potassic alteration. Dominant structures are an east-west post mineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. Two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast and the other striking northeast, dipping northwest. Mineralization is predominantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are lens important amounts of magnetite, hematite, sphalerite, galena, tennantite and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1972

By S. Natansohn

A prevalent technique for the recovery of silver from wastes generated in silver-tungsten electrical contact fabrication is electrowinning. Such scrap is placed in a permeable plastic basket which constitutes the anode compartment and this basket is suspended in a larger cell in which the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits out. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand ppm, necessitates additional purification of the deposited Ag and its removal would therefore be advantageous. The elimination of the W impurity would also extend the operating period of the cell with corresponding increase in the Ag output and savings in labor costs.

Jan 1, 1982

By Franklin B. Woodbury

As part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic needs, the U.S. Department of the Interior's Bureau of Mines is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed with a prototype monitoring system. A Californium-252 neutron source and a thermal neutron capture- gamma ray spectra analysis method was utilized to measure the amount of iron and the percent solids in the process slurries. The concentrate and tailing streams in a 410-kilogram-per-hour (900- pound-per-hour) pilot plant employing a selective flocculation and cationic flotation process were monitored. The results obtained showed that the thermal neutron capture-gamma ray reaction can be used to provide process control parameters.

Jan 1, 1979

By P. Eger, D. Green

"The Soudan Mine was Minnesota’s first iron mine, operating from 1882 to 1962. The mine was donated to the State of Minnesota in 1963 and became a state park in 1965. The mine discharge contains elevated copper and cobalt concentrations and has been treated with an ion-exchange-resin-based system since 2009. The system includes flow equalization tanks, bag and cartridge filters, a carbon tank and two commercial ion exchange tanks. Although effective, the system’s high cost, inefficient removal of suspended material and substantial maintenance have been ongoing and troublesome issues.In November 2012, we initiated a pilot test using a peat-based sorption media. This media is produced from raw reed-sedge peat through a patented, low-temperature carbonization process that produces a hardened granular sorption material. The granules are uniform, have high hydraulic conductivity and maintain the high metal affinity of natural peat.Mine water was pumped through the peat-based sorption media without any pretreatment. Copper input concentrations typically ranged from 30 to 60 µg/L but increased to a high of 364 µg/L in the summer of 2013. Since startup, more than 60 million L (16 million gal or 32,000 bed volumes) have been treated, with average removal rates of 75 percent for particulate copper and 60 percent for dissolved copper. Backwash is required at about 4,000 bed volumes, but with a combination of air sparging and high-flow backwash, the suspended material is removedfrom the media.One tank of the peat-based sorption media was found to remove copper similarly to the first four components of the existing system. By reducing size and complexity, reductions in operation and maintenance costs are possible. A comparison of the estimated costs indicate that replacing the four initial components with the single media tank has the potential to reduce annual operating costs by more than half from around $163,000 to $70,000."

Jan 1, 2015

By Robert B. Tippin

A number of recent studies 1-4 suggest that steelmaking expansion might be achieved more economically by a combination of the prereduction furnace and the electric steelmaking furnace rather than through new blast furnace construction. Supergrade concentrates would be the first step in an evolving technology which bypasses the blast furnace and in which the concentrates are first made into pre¬reduced pellets and then used directly in electric steelmaking, Prereduced pellets made from superconcentrates should not only be competitive with scrap, but should be a preferred feed for the electric furnace because of the absence of such residual elements as copper and nickel. Furthermore, geographic areas remote from present steelmaking centers may find the electric furnace to be an economical method of providing local steel requirements. The development of successful methods of producing superconcentrates may also be expected to find application to conventional blast furnace burdens. The need for methods of increasing grade of domestic concentrates will become increasingly urgent in the face of competition from high grade imports. Only a small percentage of domestic iron ore production can qualify as superconcentrates, (Superconcentrates for the purpose of this investigation are limi¬ted to those concentrates which contain a maximum of 2 percent S'02). During the last several years the Twin Cities Metallurgy Research Center of the Bureau of Mines has directed research efforts to develop methods of manufacturing superconcentrates from present standard grade products by cationic flotation, screening, and magnetic separation.

Jan 1, 1971

By H. Huang, R. N. Gow

"The reactivity of an enargite mineral electrode was investigated spectroelectrochemically under conditions typically found in alkaline sulfide leach solutions, with pH 11-13 and Na2S additions of 50 and 250 gL-1. A bulk enargite electrode was cycled between 0 and -1,000 mV for each set of solution conditions. Raman spectroscopy was used to determine and compare surface formations against species in mass-balanced EH-pH diagrams generated using STABCAL. Previously, it was determined that arsenic could be selectively leached under alkaline conditions at an average solution potential of -300mV, across the pH range 11-13. Operating under such conditions allowed for the selective leaching of arsenic with elemental sulfur formation. From several of the voltammograms obtained during this current testing, the formation of elemental sulfur appeared at increasingly reducing conditions with increasing sulfide concentration. At high concentrations, copper started to dissolve, possibly as a bisulfide complex, reducing the selectivity of the leach, unlike previous studies. However, the presence of the higher sulfide concentration is also anticipated to prevent passivation by consuming any surface formation of elemental sulfur. This study provides insight into the operating parameters of alkaline sulfide leaching in regards to the selectivity of arsenic leaching, as well as guidance for control of reagents and solution potential and, of course, the need for water treatment afterwards.IntroductionEnvironmental limitations on the pyrometallurgical processing of arsenic-bearing concentrates have forced operations to consider other solutions. Attempts to hydrometallurgically process enargite (Cu3AsS4) fall into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under basic conditions. The authors believe that the selective leaching of arsenic is more amenable because it produces a solid copper phase, preferably chalcocite (Cu2S) or covellite (CuS) that could then be processed using conventional methods already in place in the copper and gold industries. Potential leaching methods include alkaline sulfide leaching (Achimovicovica et al., 1999; Anderson and Twidwell, 2008a,b; Tongamp et al., 2009 and 2010), hypochlorite leaching (Vinals et al., 2003; Curreli et al., 2005; Mihaljovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and acid leaching (Gow et al., 2014b) with or without fine grinding to mechanically activate the enargite surface and increase normally slow leach reaction kinetics (Achimovicova et al., 1999; Balaz et al., 2000; Balaz and Achimovicova, 2006). In this study, the reactivity of enargite under alkaline sulfide leach conditions was examined."

Jan 1, 2015

By NEHA PANDEY, V.K. REDDY KALLAM, SUNIL KUMAR TRIPATHY, ARIJIT BISWAS

This work discusses the sulfur dioxide (SO2) leaching of low-grade ferruginous manganese ores to selectively recover manganese (Mn) as manganese sulfate (MnSO4), followed by electrowinning of the purified MnSO4 to produce electrolytic manganese dioxide (EMD). The effects of the leaching process parameters on Mn recovery were studied, and the leaching duration and SO2 flow rate were found to have significant effects. Under the optimum conditions derived for grade 1 ore (with total Mn content of approximately 17.16 percent), the specific SO2 requirement (SSR) — that is, the SO2 flow rate per gram of Mn in the leach slurry — was calculated to be 0.014 L/min. At the SO2 flow rate calculated using SSR for grade 2 ore (with total Mn content of approximately 26.29 percent), a Mn recovery rate of 94 percent was realized. Electrowinning of the purified MnSO4 generated after leaching resulted in EMD with 88.01 percent purity and a γ structure.

Sep 1, 2022

By Bo Hyun Kim, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health have tested the finite element code, UT3PC, with LaModel to evaluate their results using know case studies. The purpose of the testing was to demonstrate the usefulness and limitations of these programs in evaluating mine layout design. Both of these software packages are simple to use and free for public download. Their use by mine engineers, along with other tools, such as empirical methods, can enhance the assessment of a mine layout design. LaModel can model mining layout on a mine scale or, at least, on a multiple-panel scale. However, this software has limitations in calibrating to conditions at many coal mines in the western United States. The UT3PC software models smaller parts of a mine and is used to evaluate the design of pillars, shafts, or drifts; but the software calculates all components of the stress tensor and provides stresses, displacements, and safety factors throughout the model volume. The two codes are used to evaluate design of one known case, and UT3PC is used to evaluate another case. The results and approaches demonstrated in the testing are intended to aid mine engineers in evaluating site-specific problems and to show that these tools can provide useful information to the mine engineer in evaluating mine layout design.

Jul 1, 2023

By E. Gutierrez, P. Gillies

Asset Maintenance Readiness (AMR) provides a tailored reliability and maintenance strategy specific to operational needs. AMR delivers reliability and maintenance foundations for the plant and equipment before start-up. Having a dependable reliability and maintenance strategy before start-up is critical, particularly in those first weeks and months during ramp up to stable production. The Asset Maintenance Readiness is the integration of Reliability and Maintenance Engineering analysis/studies at the earliest stages of the new Production System concept and design and during the Capital Project CapEx phases; adding this analysis to the Capital Project CAPEX cost, will have an impact of 2% to 3% of total project cost, but will deliver a good compendium of benefits far from the AMR costs, and those results will be shown upon commissioning and during the life cycle of the plant.

Mar 2, 2022

By Volkan Arslan

This study aimed to remove the contaminants in quartz sand by using an eco-friendly method and to obtain high-purity quartz. For this purpose, ultrasound-assisted acid leaching was applied. Equal amounts of a mixture of diluted hydrochloric and oxalic acids were used as the solvent. Response surface methodology (RSM) was used for optimizing, modeling, and predicting the experimental parameters. The correlation coefficient ( R2) of the proposed quadratic model for the relationship between iron removal yield and test parameters was calculated as 0.9731 and it was determined that the predicted and actual values were compatible. Finally, optimization experiments were made and optimum experiment conditions were revised and determined as 83.38 °C of leaching temperature, 196.35 min of leaching time, 2.86 M of acid concentration, and 202.24 W of ultrasound power. Under the optimum conditions determined after optimization, the highest yield of iron removal was determined as 95.08%. Under the optimal parameters, the SiO2 content of the concentrates increased from 97.841 to 99.907% and the Fe2O3 content reduced from 0.225 to 0.011%.

Jul 12, 2021

Satisfactory means of managing growth in boom towns is a concern in mineral, energy and other large industrial developments. This session will include examinations of socioeconomic impacts, major issues such as social disruption, case studies, methods of managing growth, and concerns involving Indian lands. Innovative methods will be offered to assist the public, government, and industry in finding solutions to managing growth in rapidly growing communities.

Jan 1, 1979

By F. L. Jackson

When using perlite as an insulation, it is important to determine the requirements for different applications as this influences the processing of the perlite. In cryogenic applications, perlite properties of low density and fine particle size are desirable, while Loose fill insulation applications require similar properties and water repellency. However, in perlite insulating concrete applications, a coarser particle, of higher density, is required to provide improved compression strength. The essential properties of perlite including, particle size, density and surface treatment are discussed in relation to the various insulation applications. Also typical mineral processing and manufacturing techniques are reviewed

Jan 1, 1983

By K. A. Perry, R. Q. Eades

The University of Kentucky conducted inerting tests and angle of ejection tests on three types of rock dust. A newly developed hydrophobic dust was compared against typical dry and wet dust applications. This new product is designed to alleviate respirable dust concerns for dry dusting and caking issues with wet dusting. Samples for both test types were prepared in a laboratory and subjected to temperature and humidity cycles that are typical of an underground coal mine. Inerting tests were conducted in a 38-L chamber with a 5-kJ Sobbe igniter. Angle of ejection testing was conducted at the University of Kentucky Explosives Research Team’s laboratory in Georgetown, KY. The results of these tests indicate that the newly developed dust has improved results for flame suppression and ejection compared with typical wet dust applications. The significance of these results is discussed with regard to existing respirable dust regulations and the issues associated with caking.

Jan 1, 2016

By K. D. Luxbacher, E. C. Jong

Perfluoromethylcyclohexane (PMCH), a member of the perfluorocarbon tracer group of compounds, has been shown to be a viable supplement to the widely used tracer gas sulfur hexafluoride (SF6). This viability stems from the fact that PMCH can be used concurrently with SF6 while maintaining adequate chromatographic separation and comparable sensitivity during analysis. However, the release of PMCH in an underground mine ventilation system is challenging due to its physical characteristics. While SF6 exists as a gas at room temperature and pressure and can be accurately released by a variety of means, PMCH exists as a volatile liquid at room temperature and pressure, preventing it from being deployed in a similar manner. One method to release PMCH is to use a permeation plug passive release vessel (PPRV), which allows for the controlled release of the gas. This paper presents the results of a study evaluating various preparation techniques, plug thicknesses and plug materials of an aluminumvessel PMCH release source, so that a source appropriate for the mine scale may be developed.

Jan 1, 2015

By William J. Almas

Operating uranium mill tailings containment and mill decommissioning activities are regulated by the Nuclear Regulatory Commission (NRC) and the Environmental Protection Agency (EPA) through numerous regulatory mechanisms. Reduction of radon emissions from tailings disposal areas, remedial actions to return groundwater to baseline constituent concentrations, and 200-to 1,000-year stabilization of tailings are major focus areas of regulation. The cumulative economic impact and uncertainty associated with regulation are very significant and will hinder future development of uranium milling facilities.

Jan 1, 1991

By A. K. Bhasin

The movement of solid particles in a liquid represents an area of interest in many fields of science and technology. Knowledge of the behavior and characteristics of solid-liquid suspensions is of great importance to many areas of mineral processing. In order to characterize a solid-liquid system, the following factors must usually be considered: a) density of the liquid b) rheological properties of the liquid c) density of the solid particle d) size and shape of the solid particle e) volume fraction of solid particles f) relative motion of solid particles and liquid phase Other variables such as the effect of the containing vessel walls, Brownian movement, inter-particle friction, fluid slip and electrostatic effects, are important in special circumstances. Thus it is evident that a complete theoretical treatment is not possible covering all situations. Studies of the kinematic behavior of solid particles in a liquid have been approached by two methods: 1) Assessing the movement of a single particle and extrapolating to a multi-particle system; 2) Modifying the continuum mechanics of single-phase liquids in such a way as to account for the presence of solid particles. The first approach in general utilizes the method of particle mechanics. Extension to a multi-particle system gives rise to very complicated mathematical computation. The creeping motion equations do, however, furnish a practical, useful basis for achieving a uniform treatment and a better understanding of the phenomena. This approach is useful in the study of sedimentation and hindered settling processes.

Jan 1, 1971