Search Documents

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance within the system is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation. Upgrades to the primary ventilation system are often required. The use of booster fans underground is a potentially practical alternative to the addition of shafts and surface fans. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room-and-pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is the most popular and practiced mining method in underground hard rock mines. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason is the unavailability of free faces as compared to opencast bench blasting. The geological and geotechnical parameters change gradually even within the stope itself. So, the blast design parameters should be planned according to the scenario of the upcoming ring. The blast design parameters like burden, toe spacing, inclination of blastholes, diameter of blastholes, charge density of explosive, etc., play an immense role in the rock damage. For the proper breakage of rock, the movement of burden is the prime objective. To study this, an explicit dynamic based modeler of M/s Ansys was used. The burden values were varied from 20 to 65 times of blasthole diameter to assess the optimum burden value during the study. The models were simulated for the rock having uniaxial compressive strength as 35 MPa and 102 mm blasthole diameter. Three holes were simulated having depth around 14–14.5 m. Different blast design parameters and respective blast-induced ground vibration have also been measured at the experimental site. The core samples of the rock present at the experimental site have been used for the evaluation of geotechnical parameters. These geotechnical parameters were used in the simulation models. The volume of rock excavated along the free face has been calculated in each model by varying the burden. It has been found that the burden value can varies from 35 to 40 times blasthole diameter (3.6–4.1 m) to achieve a greater volume of rock along the free face for 102 mm blasthole diameter and rock of 35 MPa uniaxial compressive strength.

Dec 22, 2023

By M. Sunkpal, K. C. Kocsis

"An underground environment with high air temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to a series of heat-related illnesses such as heat exhaustion, heat cramps and heat stroke. The majority of the metabolic energy of a mine worker results in the production of heat. If the human body is to maintain thermal equilibrium, then this metabolic heat must be transferred to the ambient surroundings at the same rate. The heat loss from the human body occurs through a combination of heat transfer processes, such as respiratory heat exchange, convection, radiation and evaporation. If the heat loss from the human body to the ambient surroundings is less than the metabolic heat produced, the excess will be accumulated within the human body, which will result in a rise in the core and skin temperatures. This can ultimately lead to a heat-related illness or a combination of heat-related illnesses. This paper aims to discuss major heat-related issues and provide an overview of various mine ventilation and cooling systems, which can be employed to overcome high levels of heat and humidity in underground mines. In this paper, the effects of heat exposure on the health, safety and productivity of the mine workers are also highlighted. IntroductionMining in the United States remains one of the most hazardous industries, despite significant reductions in fatal injuries over the last century (Coleman and Kerkering, 2007; Saleh and Cummings 2011; Jacklitsch, Musolin and Kim, 2016). Occupational health hazards within the mining industry include hazards that are physical, such as traumatic injury or hearing loss; chemical, such as silica or diesel particulate matter; biological; ergonomic; and psychological (Donoghue, 2004; Saleh and Cummings, 2011). The effects of some of these hazards can be diagnosed immediately, while many, like black-lung and silicosis, will have long-term effects on the health, safety and life quality of mine workers (Donoghue, 2004; National Institute for Occupational Safety and Health, NIOSH, 2000). Among these hazards, exposure to heat and humidity can significantly affect the safety, health and productivity of mine workers, particularly in deep and hot underground mines (Roghanchi, Sunkpal and Kocsis, 2015). Short-term acute heat exposures can cause a rise in the core temperature of the human body, which can result in a heat-related illness or combination of heat-related illnesses. Adverse long-term chronic heat exposure can generate serious occupational heat-related illnesses, such as cardiovascular diseases, mental health problems and chronic kidney diseases. High core body temperatures coupled with dehydration can generate negative behavioral effects such as physical fatigue, irritability, lethargy, impaired judgment, loss of dexterity and loss of concentration (Xiang et al., 2014)"

Jan 9, 2017

By C. D. Iles

The philosophy used in designing and writing Duval's Sierrita mine design programs is discussed. The Sierrita Incremental Design system (SID) is reviewed with emphasis on Pushback Extraction Design (PED). FED is a method by which predesigned pushbacks are sequenced into an optimized period-by-period design that can be directly utilized in daily operations as well as intermediate and long range planning. The advantage of SID is that it provides a practical, mineable open pit design. PED is not a theoretical design system; it is in operational use.

Jan 1, 1981

By M. Scaggs

"Respirable dust in underground coal mines has long been associated with lung diseases, and regular dust sampling is required for assessing occupational exposures. At present, respirable dust concentration and crystalline silica content are commonly determined, but considering recent and yet unexplained increases in the incidence of lung disease amongst miners in specific geographic regions, more information about specific dust characteristics is urgently needed. While particle-level dust analysis is ideal, it is impractical for large numbers of dust samples because it is both time and cost intensive. Thermogravimetric analysis (TGA), however, is an alternative option, which offers the ability to determine the total coal to mineral mass ratio in a dust sample – analogous to proximate analysis of bulk coal samples for determining ash content. Here, preliminary development of a TGA method for this purpose is presented. The method is being developed to evaluate dust collected on mixed cellulose ester (MCE) filters using approved permissible sampling equipment. INTRODUCTION Based on the particle size, airborne mine dust can be classified in three categories: inhalable dust (< 100 µm in size), thoracic dust (< 25 µm in size), and respirable dust (< 5 µm in size) (Ramani et al., 2003). The World Health Organization (WHO, 1999) defines inhalable dust particles as those which can be breathed into the nose and mouth, and thoracic dust particles as those which can penetrate airways of the head and enter the airways of the lung. On the other hand, respirable dust particles can penetrate beyond the terminal bronchioles into the gas-exchange regions (alveoli) of the lungs (WHO, 1999). Hlavay (1992) reported that the seriousness of the damage in the lungs and respiratory tract is based on amount of dust remaining in these organs, and the amount of dust depends on the extent of dust exposure, the size distribution of the dust particles, and the capability of the body for dust elimination. Inhalation of respirable coal dust by miners can cause a disabling and potentially fatal lung disease which is called coal worker’s pneumoconiosis (CWP). Silicosis is another fatal lung disease caused by inhalation of respirable silica dust. In CWP and silicosis, dust particles deposit in the lungs, damage the lung tissue, and ultimately cause scarring which cannot be reversed (Colinet, 2010). While overall incidence occupation-related lung disease amongst coal miners in the US has been declining for over 40 years, it appears that there has been a recent increase in specific locations in Central Appalachia (CDC, 2006; Pollock et al. 2010; Suarthana et al., 2011). Although this trend is yet unexplained, one theory is that particular dust characteristics in these locations may be a factor (Hassan and Lau; Page & Oraniscak 2002). For example, several studies have indicated that different coals may generate different amounts of respirable dust (e.g., see Page, 1993 and Litton and Page, 1994), and the surrounding geology may also play a role in terms of the types of dust particles generated. Although respirable dust concentration and crystalline silica content are commonly determined as part of regulatory compliance sampling, more information about specific dust characteristics (e.g., size, shape and composition) is urgently needed."

Jan 1, 2015

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a com- plex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of the the more common evaluation tests made on coal and how the test results are applied in commercial practice. Parameters used to select coal blends for wet and preheated charges should also be of interest.

Jan 1, 1980

By Glenn E. Hoffman

Relax: the world today is not running short of many mineral commodities, even though prices are spiraling upward. Einstein?s observation still holds true that everything is still relative, as long as one can pass on the incremental costs of production to the consumer. However, a strong consensus exists among many of the companies comprising the minerals processing industry that it is becoming increasingly difficult to find the easy-to-mine, high-quality resources that make juicy profit margins, which shareholders like. For the most part, the resource cherries have all been picked, and established mineral processing companies that are exhausting their reserves, or in the process of looking to add reserves so as to create longevity for their company, have no recourse but to look long and hard at what were once considered the dregs of the earth. Even end users, such as steel companies, are now looking to become ?miners,? to establish captive iron ore resources. Owning a captive resource facilitates a dependable supply of feed materials, which translates into effective cost control and a guarantee for a thriving sustainable business in the future.

Jan 1, 2012

By L. L. Chasko, D. W. Alexander

Researchers from the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research conducted an assessment of the effects that ground control mesh might have on rock and float coal dust distribution in a coal mine. The increased use of mesh to control roof and rib spall introduces additional elevated surfaces on which rock or coal dust can collect. It is possible to increase the potential for dust explosion propagation if any float coal dust is not adequately inerted. In addition, the mesh may interfere with the collection of representative dust samples when using the pan-and-brush sampling method developed by the U.S. Bureau of Mines and used by the Mine Safety and Health Administration for band sampling. This study estimates the additional coal or rock dust that could accumulate on mesh and develops a means to collect representative dust samples from meshed entries.

Jan 1, 2014

By Harold J. Schock

This paper describes an experimental method for the monitoring of diesel-generated exhaust gas pollutants in a dead-ended drift for the purpose of assessing the effect of control approaches. Experiments were conducted to determine the relative merits of these ventilation configurations: no auxiliary ventilation, induction ventilation at the entrance to the drift, and ventilation of the dead-ended drift with positive displacement tubing. The drift used in this experimental work was approximately 105 ft. (32.0 mf long and slightly downsloping, with an average height and width of 8 ft. (2.4 m) and 28 ft. (8.5 m1 , respectively. The data were gathered for assessing these ventilation methods and for gathering data to support a computer model of the dispersion and mixing processes. For this drift, it was found that ventilation with positive displacement tubing provided the best removal of diesel-generated pollutants. Induction ventilation appeared to be the least effective of the three methods examined. A comparison was also made between personal monitoring and area monitoring. Results of this analysis showed that in regions of high concentration gradients, it was not possible to get good agreement between point sampling and personal monitoring. In well-mixed areas, good agreement between the two methods of monitoring was obtained.

Jan 1, 1980

By Megan Badonie, Devlon Shaver, Evan J. Owen, Virginia T. McLemore, Jakob Newcomer

Critical minerals are becoming more important in our technological society because they are used in many of our electronic devices, batteries, and magnets. In New Mexico, low to moderate concentrations of critical minerals are found in Late Cretaceous coal and related strata in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, REE, and Critical Minerals) program. The New Mexico coal, humate, and clinker deposits are relatively low in REE (<325 ppm TREE), Li (<90 ppm), V (<168 ppm), Co (<51 ppm), Ni (<108 ppm), Zr (<557 ppm), and many other critical minerals compared to normal economic deposits. Some of these rocks are enriched in Al2O3 (<40%) and Sr (<3740 ppm), both critical minerals. Common minerals hosting the critical minerals in these rocks include clay minerals, zircon, and rutile/anatase. As the demand for some of these elements increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Ultimately, economic potential will most likely depend upon production of more than one commodity, maybe even from coal, humate, and clinker deposits.

Feb 1, 2024

By Staff

"In 2014, the estimated value of total mine production of nonfuel minerals in the United States increased. The quantity of production increased for most mineral commodities mined in the United States, as did prices. Notable exceptions were the declines in prices for most precious metals. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Following the reduction in construction activity associated with the 2008- 2009 recession that continued through 2011, the construction industry continued to expand in 2014, with increased production and consumption of cement, construction sand and gravel, crushed stone and gypsum, mineral commodities that are used almost exclusively in construction. Other segments of the nonfuel minerals industries increased as well. Trends in other sectors of the domestic economy were similar to those for industrial mineral production (Table 1).Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals. Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. The materials with the highest unit values, usually metals, tend to have very low production rates compared with those of many low-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the minerals industry in general, the value of production is used rather than tonnage produced. Although the value of metals and industrial minerals mined in the United States are similar, if tonnages are compared, construction aggregates dominate, dwarfing the production of all other minerals combined.Mineral industry performanceThe estimated value of nonfuel mineral raw materials, including metals and industrial minerals, produced at mines in the United States in 2014 was $77.6 billion, a 3.5-percent increase from $75 billion in 2013 (Table 2). Net exports of mineral raw materials and old scrap were $15 billion (Fig. 2). Domestic raw materials, along with domestically recycled materials, were used to process mineral materials worth $697 billion. These mineral materials, including aluminum, brick, copper, fertilizers and steel, and net imports of processed materials (worth about $41 billion) were, in turn, consumed by downstream industries with a value added estimated to be $2,530 billion in 2014.In the United States in 2014, mine production of each of 14 mineral commodities was worth more than $1 billion. These were, in decreasing order of value, crushed stone, copper, gold, cement, construction sand and gravel, iron ore (shipped), industrial sand and gravel, molybdenum concentrates, phosphate rock, lime, salt, zinc, soda ash and clays (all types)."

Jan 1, 2014

By L. L. Chasko, D. W. Alexander

Los investigadores del National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research han evaluado los efectos que la malla de control de suelos podría tener en la distribución de polvo flotante de roca y carbón en minas de carbón. El creciente uso de mallas para controlar el desconchado o caída de material del techo y las vigas introduce superficies elevadas adicionales para recolectar el polvo de roca o de carbón. Es posible que el potencial para la propagación de explosión del polvo se incremente si el polvo flotante de carbón no es convertido en inerte de manera adecuada. Adicionalmente, la malla podría interferir con la recolección de muestras representativas de polvo cuando se usa el método de recipiente y brocha desarrollado por la U.S. Bureau of Mines y usada por la Mine Safety and Health Administration para muestreo de banda. Este estudia hace una estimación del polvo de roca o carbón adicional que pudiera acumularse en la malla y desarrolla un método para recolectar muestras de polvo representativas atrapado en las mallas.

Jan 1, 2014

By Donald C. Strimbeck

The Bureau of Mines, U.S. Department of the Interior, is conducting research and development on a coal-burning gas turbine. This work includes the development of (1) turbine blades resistant to coal ash erosion, (2) equipment to feed coal under pressure to a turbine, (3) an efficient combustion system, and (4) equipment to remove coal ash from the gases that drive the turbine. Initial emphasis is being placed on testing the first turbine ever equipped with blades designed specifically for use with coal as the fuel. Operating tests with this turbine are now in progress. This paper describes the Bureau&apos;s coal-burning gas turbine development program and progress on this operating test.

Jan 1, 1964

By J. Robert Denny

The impact of the computer revolution--so pervasive in some industries--has been less startling in the mining industry. Computer techniques have been used successfully to provide drill hole calculations, contour maps, and a variety of conventional maintenance scheduling, and accounting applications. But it is our experience that the real economic payoffs lie in the engineering application of computers to mine planning and the use of systems engineering techniques for mine operations. Since 1964, Newmont Mining Corporation has been engaged in systematic research and development of computer techniques in a variety of mine planning applications. The general objective in using computers has been twofold: first, to arrive at a viable, near-optimum plan for mining a particular orebody, and second, to decrease the financial investment by reducing the man-hours required for mine planning. Three major phases in the evolution of these computer techniques for mine planning are discernible. In phase one, the machine capability for duplicating manual drafting and contour mapping was developed. The necessity of including all recognized geologic characteristics is obvious. Capability for properly incorporating structure, stratigraphic trends, and other geological features was a significant aspect of phase one development.

Jan 1, 1970

By N. K. Bohidar

Evaluation of the stability of a structure under given boundary conditions requires accurate knowledge of the state of stress as well as the mechanism of failure at the critical state of stress. This paper represents a part of the research done by N. K. Bohidar during 1965-1968 for his Ph. D. research in Mining Engineering at the University of Utah. It summarizes the determination of internal stress and failure phenomena around cylindrical openings in viscoelastic media subjected to lateral restraint and vertical uniaxial load. The conditions of lateral restraint and viscoelastic nature of the media represent conditions associated with subsurface openings in rocks. The financial assistance provided to the project from the University of Utah Research (Uniform School Fund), W. C. Browning Scholarship Fund, Earth Science Research Fund, and D. C. Jackling Loan and Scholarship Fund is gratefully acknowledged. The authors also acknowledge the assistance of S. Siugh, W. Jones, and K. McCarter during the project.

Jan 1, 1970

By Ping Zhang, Shahram Mozaffari, Andreas Ylmefors

The risk associated with mining induced seismicity and the related rock bursts has become one of the major threats to the safety and sustainability of mining at the Kiirunavaara mine. The causes of mining induced seismicity at the Kiirunavaara mine are very complex and have affected our understanding on the source mechanisms of seismicity and further the mitigation of the seismic risk. Detailed analysis of historical mining induced seismicity at the Kiirunavaara mine was conducted. The focus of this analysis was placed on the classification of large seismic events and the evaluation of the influential factors on the classified seismic events. 145 events with local magnitude larger than 1.5 that occurred between January 1, 2011 and March 31, 2021 were analyzed. For this analysis, seismic events located in the hanging wall were not included, as these have not been observed to cause large damages to the mine itself. It was found that the magnitude of the events had good correlation with the stress change in relation to the production location. The seismic events were classified as mining-front associated, ore-pass associated, mining-front and ore-pass associated and others, according to their hypocenter location. Most of the mining-front associated events, concentrated around the production levels and slightly above and below them, generally correlated with shear cracks, and most of them occurred when the ore flow between two production levels started. The numerical modelling showed that slip of the geological discontinuity, due to unclamping between hanging wall and footwall, could be the major causative mechanisms, which further supports this finding. The ore-pass associated events are located close to the ore passes. Large seismic events located between ore passes have the source mechanism of both fault-slip and non-shear, but events located at the outer side of ore passes were all fault-slip type. By checking with the ore pass scanning data, it was concluded that the most of the events located between ore passes could be pillar bursts. An elastic core concept has been then used to define a critical pillar width. The paper is not intended to be prescriptive but rather to initiate discussion of the possible classification of seismic events at the Kiirunavaara mine and to present new perspectives of the causes of the seismicity for improving the present seismic risk management.

Apr 26, 2022

By Alexander N. Winchell

"THE MICHIGAN COPPER DISTRICT.Location. The copper mines of Michigan are all in the north¬ern part of that state on the Keweenaw Peninsula, which extends from the (Michigan) mainland for about seventy miles northeast¬erly toward the middle of Lake Superior. The mines occur in a belt or zone occupying the central portion of the peninsula from end to end.. The most productive mines for many years past have been those located not far from the city of Houghton in&apos; the central part of the zone, in a section extending about ten miles southwest of Houghton and fifteen miles northeast. The most important mines in order of.location, from the northeast to south¬west, are the following: Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet. and Hecla, Osceola, Franklin, Quincy, Hancock, Isle Royale, Superior, Baltic, Trimountain, and Champion. The first three named are in Keweenaw county and all of the others are in Houghton county. Still farther to the southwest are the Lake, Mass, Adventure, Michigan, Victoria, and White Pine mines. These are in Ontonagon county.History. The exploitation of these copper mines extends back into prehistoric times. There is little evidence that the American Indians carried on mining operations in this region in the period shortly before the advent of white men, but there is abundant evidence that the ancestors of the Indians, •or some earlier inhabitants of the region, carried on primitive mining operations. For example, Mr. S. O. Knapp, Agent of the Minne¬sota Mining Company, in the winter of 1847-48, made the first discovery of prehistoric mining. This event is described as fol ,lows by Foster and Whitney : Location: As shown on the accompanying map, the Mar-quette district extends from the region of Marquette on Lake Superior westward for about forty miles. The main basin of the district is only about three to six miles wide, but outlying areas which are commonly regarded as belonging to the same mining unit, make the north and south dimension of the district about twenty miles. The most productive portion of the area is in the vicinity of Negaunee and Ishpeming, .about ten miles from Mar¬quette, but important mines are found also all along the range as far west as Michigamme and also to the south in the fold known as the Republic Trough. Comparatively recent developments indicate that important ore bodies have been developed in the outlying Swanzy district about eighteen Miles nearly due south of Marquette.The Marquette Iron District.History: The first discovery of iron ore in the Lake Supe¬rior region was probably that made in 1844 near the site of Ne-gaunee by the government surveying party in charge of William A. Burt, sent out under the direction of Douglass Houghton. This surveying party was using a solar compass, invented by Mr. Burt, and noticed variations in the direction of the magnetic needle at various times and places, but. on the 19th of September, while running the east line of Township 47 North, Range 27 West, the needle varied from its normal position until it stood nearly at right angles thereto."

Jan 1, 1920

By Kenneth W. Luke

In the development of the ultimate pit limits for a narrow ore body, pa¬rameters necessary in the design of a functional, or working, pit become highly sensitive factors in the determination of ore reserve levels and their associated waste to ore stripping ratios. Through the use of geologic cross sections, ore reserves can be roughly calculated by utilizing a straight line approximation for pit wall slopes. The optimum position of the pit floor can be substantially altered from such a preliminary design though with the introduction of functional mining parameters, such as a ramping network, and working bench heights, berm widths, and bench to bench wall angles. Originally a computer program was developed to quickly evaluate changes in cross-section pit design with minimal alteration of input data. After developing a satisfactory technique of cross-section evaluation which incorporates working mine parameters, an optimization algorithm, or procedure, was developed and included in the program to eliminate much of the tedious manual decision-making required in determining the optimum location of the pit floor on each cross section. Optimization in this case implies the maximum profit pit. When pit and processing costs are defined or hypothesized, this computer program can be used to design the maximum profit pit, constrained by the recognized functional mining parameters. A second way of stating the optimization is that the program can be used to develop a pit design which minimizes waste stripping at any desired ore reserve level. The basic method of cross-section evaluation parallels present manual methods. Program input is a combination of data obtained directly from cross sections developed for, geological interpretation and pit design parameters selected by the mine planner. As a result it is easy for the mine planner to comprehend what the program is accomplishing, and thus participate in the development of the computer assisted design.

Jan 1, 1971

By Deepak Malhotra

This paper discusses the need for periodic auditing of mineral processing flowsheets and the potential benefits a company can gain from a study of this nature. A carefully designed flowsheet auditing can have a significant impact on the metallurgical performance in the plant. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1986

By S. R. Dindarloo

"Truck-shovel systems are the dominant material loading and haulage machinery in open pit mining operations. Optimal selection, sizing, and allocation of this capital intensive equipment is highly desirable for both achieving production targets and improving the mine’s economics. In this study, discrete event simulation technique was applied for modeling material transportation in Golegohar open pit iron ore mine in Iran. Direct observation of the material loading and haulage for duration of three months resulted in statistical modeling of the operation in the form of probability distribution functions. These probability models were used as the inputs of a stochastic simulation model constructed in GPSS/H simulation language. The model was validated through comparison with the actual operation and was used to test different what-if scenarios and sensitivity analysis of the current system. Some modifications in the number of trucks, shovels, and dispatching strategies were proposed. Simulation resulted in considerable improvements in the mine’s production and economics.INTRODUCTION There are three different mechanisms of discrete, continues, and hybrid material transportation in open mines, including but not limited to: i) in-pit crusher and conveyor belts (hybrid), ii) slurry piping (continues) and iii) truck-shovel system (discrete). Although, each mechanism has its advantages, the truck-shovel system is the dominant method of material loading and handling in open pit mines owing to its high production rate, excellent flexibility, relatively low operating and capital costs, and good maintainability. General objectives of optimal equipment selection include: i) meeting the long and short term requirements of production rates, ii) human & equipment safety, iii) environmental protection, and iv) economic operations (Figure 1).The two most important decision factors on a truck-shovel system selection and sizing are the equipment geometry and size. Geometry (equipment width, weight, turning radius, swing angle, etc.) is mostly controlled by mine’s designs and layouts, as well, as operational constraints. After selection of a favorable geometry based on the constraints; the next step is to select the equipment manufacturer. Once the geometry and manufacturers are selected; the next step is to decide on models (e.g. Bucket size) and required number of each unit"

Jan 1, 2015