Search Documents

By John M. Arnold

Several years ago it became apparent to some of our people that; there was developing a very definite need for largee coal reserves in the West to satisfy- the need for fuel for the furnaces of electric generating plants with the rapid development of, the West, of both population and industry, it was impossible for hydro-electrics plants to keep up with the ever increasing demand for electricity. In 1960, Mr. E. R. Phelps, then associated with the engineering department of Peabody Coal Company, began a search for and development of coal deposits in the very remote northeast section of Arizona near the village of Kayenta. Travel to this section of the country was not easy even at this late date, and it was an eight hour drive from Farmington, New Mexico to Kayenta, Arizona, a distance of some 130 miles. The trip was over roads that even' a-horse and wagon had trouble negotiating and a four wheel drive vehicle was about the only type of transportation that could satisfactorily traverse these roads, as testify many badly beaten sedans and coupes that tried it. Since that time a very excellent road has been constructed from Shiprock; New Mexico to Cameron, Arizona where it junctions with another excellent road that runs north to Page, Arizona and the Lake. Powell area and south to Flagstaff, Arizona on highway 66. Kayenta is a small village nestled at the foot of the Black Mesa near its northeast extremities. The coal deposits of interest were on the surface of the mesa. This location presented another problem, as the only trail to the top of the mesa was intended for walking, horseback, or a brave soul In a horse and wagon. Once again the four wheel drive vehicle was about the only answer. To reach the coal deposits you must climb the mesa, which is vertical ascent of some 1,500 feet, and then proceed southward into the bowl of the mesa with an ensuing descent of some 1,000 feet, finally coming to an elevation of 6,500 feet, at which elevation the coal outcrops become apparent.

Jan 1, 1969

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020

By R. Y. K. Yang, O. Olajide, E. H. Cho

"This study focuses on partial leaching of coal pyrite with sodium sulfite in order to increase its degree of liberation from the coal matrix, which might help to increase the removal of coal pyrite, together with trace elements of arsenic (As), selenium (Se) and mercury (Hg) by froth flotation. The U.S. Bureau of Mines’ two-stage reverse flotation process was applied to further reject coal pyrite in the second stage, where pyrite was floated while coal was depressed. The results show that the leached coal flotation with sodium sulfite produced lower pyritic sulfur content in the clean coal by approximately 25% compared to the flotation of unleached coal. The synergism mechanism between the leaching and the two-stage flotation is delineated. The rejection of trace elements (As, Hg and Se) after the two-stage flotation process with unleached coal followed approximately that of pyritic sulfur (64.6%). However, after the two-stage flotation with leached coal, the rejection of Se was as high as that of pyritic sulfur (77.9%), while the rejections of As and Hg were 20% lower than that of pyritic sulfur, or followed approximately the same rejections obtained through the two-stage flotation with unleached coal.IntroductionSO2 is a reducing reagent, but when it is combined with oxygen in an acidic solution, it will become a strong oxidizing reagent for leaching coal pyrite. Sundaram et al. (2001) found that the reagent could leach coal pyrite to produce ferric iron, which, in turn, catalyzed the oxidation of SO2. Similarly, Cho et al. (2009) found that the reagent could leach pyrite as well as mercury from coal. In the present study, coal was preconditioned by partially leaching coal pyrite in water-coal slurry with sodium sulfite at 48° C. The partial leaching of coal pyrite may enhance its degree of liberation from the coal matrix and give a chance to be rejected more effectively during the flotation.The two-stage U.S. Bureau of Mines’ reverse flotation process (Miller, 1975) was used in this study. The first stage is conventional flotation, in which coal is floated while material with higher ash and pyrite content remains in the cell. Kerosene is used as a promoter to float the coal and MIBC (methyl isobutyl carbinol) is used as a frother. In the second stage, the floated coal from the first stage is depressed using a starch-based reagent, while coal pyrite is floated using potassium amyl xanthate. In this second stage, the liberation of coal pyrite from the coal matrix seems to be an important factor for successful rejection of coal pyrite."

Jan 1, 2015

By B. A. Wills

With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the very fine mineral particles in these ores. Not only is this expensive but it leads to greater losses in 'slimes'. In the early 1970's, 50% of the tin mined in Bolivia, 30% of the phosphate mined in Florida and 20% of the world's tungsten were lost in this way (Somasundaran, 1979). Gravity concentration techniques become unacceptably inefficient for particle treatment below 25-50µm, and even flotation fails in the ultra-fine range. Two approaches can be adopted to try to overcome this problem. The first involves increasing the efficiency of existing equipment or developing new slimes treatment processes. Gravity devices such as the Bartles-Mozley concentrator have been developed for this purpose and good recovery has been reported from 100µm down to 5µm. Such machines, however, have relatively low throughputs, so that large areas of plant space are generally required. Flotation is rapidly growing in importance for the treatment of ultra-fine minerals traditionally treated by gravity concentration.

Jan 1, 1986

By Xuezhong Wang, Hao Guo, Tao Tu, Qingsheng Liu

The scheelite concentrate was leached with a mixture of sulfuric and oxalic acids. Chemical compositions, mineral phases, and morphology were characterized by XRF, XRD, and SEM–EDS. Based on the results of the single-factor experiments, the response surface methodology (RSM) was chosen to optimize the leaching parameters: temperature, time, and concentrations of sulfuric and oxalic acids. The RSM results indicate that the optimum values for those parameters are as follows: temperature 72 ℃, sulfuric acid concentration 1.48 mol/L, oxalic acid concentration 0.96 mol/L, and reaction time 2 h. Under the optimal leaching conditions, the model predicts a maximum leaching yield of 99.5%, compared to the value of 99.1% obtained experimentally, that is, a discrepancy of only 0.04%. This good correlation shows that the quadratic polynomial equation obtained by the RSM optimization is reliable. The importance on leaching parameters of scheelite is, in decreasing order, temperature, time, sulfuric acid concentration, and oxalic acid concentration.

Oct 11, 2021

By C. Dan Kealy

Recent antipollution legislation for the control of mine tailings and waste-water has required an increasing number of tailings ponds. Many of these new waste-retention ponds are being constructed in congested locations, or the older ponds have reached such a size that--if failure occurs--they pose a threat to human life and public property. Although the typical tailings-disposal embankment represents--to the casual-, observer or the economy-minded mine official--a rather ugly but benign and stable pile of waste, they are in fact an extremely sensitive structural mass, retained behind the frailest of dikes. Failure of the waste mass requires only a minor change in water retention or weather conditions, erosion or piping of the ground strata, shifts in load or slight earth tremors. When failures occur, the results can be disastrous. In the U.S., we have been fortunate that, so far, pond failures have not caused loss of life. Thus, failures in this country have attracted little public attention. Present tailings-pond construction methods used by the mining industry require the barest money investment, and little engineering effort. Unfortunately, this superficial approach may increase short-term profits, but the practice may be conducive to the construction of needlessly weak structures. In coming years many of these designs will probaly become corporate liabilities. A typical pond is portrayed in Figure IA. This particular pond in Arizona is 1 mile long and 3/4 mile wide. Illustrated in Figure lB is a representative pond in cross section. This paper in concerned with two basic features common to all tailings disposal: (1) location of the phreatic surface within a tailings-pond embankment because of its influence on embankment-slope stability, and (2) prediction of

Jan 1, 1971

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

The advantage of using ammonium phosphate salt as flux is the selective precipitation of chromium(III) compounds, which are considered nontoxic and environmentally friendly. The technique in this paper is determined to have potential to be applied in the metallurgical industry, where it can be used in the beneficiation of chromite mineral ores. The higher chromium contents of chromite ores often require furnaces to run at higher temperatures of above 1,300 °C, which can cause shutdown of the ore processing plant and accumulation of the sticky chrome compounds — including toxic chromium(VI) waste — which are generated as byproducts. The other advantage of this technique is its low to moderate energy consumption compared to existing techniques.

By Douglas R. Shaw

Normal dodecyl mercaptan was evaluated as a collector for flotation of sulfide minerals and precious metals. The reagent is from the class of normal mercaptoalkanes (n-alkyl thiols), and is commercially available in the form of a mixture of n-dodecyl mercaptan and a dispersant, under the trade name Pennfloat(TM)3. Reported are results of bench-scale flotation experiments on many commercially treated base metal and precious metal sulfide ores. Dosages, points of addition, and flotation pH were among the uariables studied. Most notable results were increased copper, molybdenum, and precious metals recoveries. Dosages of dodecyl mercaptan on some ores were considerably lower than required for conventional collectors.

Jan 1, 1979

By Frederic Chavan, Hans Jakob Windier, Shane Yanagisawa, Willy Ritz

The Zurichberg twin track tunnel is the main segment of the Swiss Federal Railway's new expressline. A heavy concrete lining with a circular cross-section was chosen to cope with the swelling tendency of the surrounding rock. The 4,356 m (14,300 ft) long, 11.52 m (38 ft) diameter tunnel was driven using a shielded Robbins TBM. A 1.20 m (4 ft) wide, 25 cm (10 in) thick precast lining was placed from within the shield tail as the excavation progressed. Tunnel excavation and initial lining operation were completed in 18 months, averaging 11.86 m/day (40 ft/day) in two nine hour shifts. After breaking through, the final 28 cm (11 in) thick concrete arch lining was cast in place.

Jan 1, 1989

By SUHAINA ISMAIL, NORLIA BAHARUN, SHAIK ABDUL RAHMAN, WAN NUR SYAFIQAH ANUAR, MOHAMMAD REZAEI ARDANI

Refractory gold ore contains sulfide minerals like pyrite, chalcopyrite and sphalerite that are difficult to be directly leached by cyanidation or by lixiviants such as thiourea and halides. In such cases, it is necessary to perform oxidative pretreatment of the ore to oxidize the sulfide matrix, and gold particles can be exposed to the solution during the leaching process [1]. In recent years, hypochlorite and chloride solutions have been introduced as alternative materials for hydrometallurgical methods of gold extraction instead of cyanide solution [2]. A previous study by Hasab et al. [3] reported that the gold dissolution rate in hypochlorite solution was higher than in the cyanidation process, due to the presence of hypochlorous acid (HOCl) as a strong oxidizing agent. In a hypochlorite leaching system, the change in pH can influence the presence of oxidant species in the solution: the hypochlorite ion (OCl−) is stable in pH greater than 7.5, HOCl can be found in pH between 4.0 and 7.5, and aqueous chlorine (Cl2 (aq)) is the predominant oxidant when pH is below 4.0. As HOCl is the most effective oxidizing agent for gold extraction, pH should be maintained in the range of HOCl stability [4].

By Pan Gao, Songyang Yin, Zhibiao Guo, Jinglin You, Yuhui Li

Under the geological conditions of the interaction of upper goafs and lower working face in deep mining, coal seam mining causes a large stress concentration, which may lead to large deformation of the surrounding rock and rock burst risk. The research reported herein is aimed to utilize the FLAC3D software to establish a three-dimensional numerical model and analyze the law of the surrounding rock stress evolution during coal mining under complex geological conditions. The simulation results reveal that the peak abutment stress reaches its maximum value at 20–30 m in front of the working face, about 1.8–4.3 times the original rock stress, and the peak stress is larger in the stable mining stage. Along the dip of the working face, the peak stress occurs about 8–10 m away from the roadway side. The upper barrier coal pillar and the interval coal pillar in order exhibit stress concentration areas of 142 m and 88 m. According to the law of the deflection stress distribution of the surrounding rock in the presence of various widths of the coal pillar, a 10-m coal pillar between the roadway and the adjacent goaf could enhance the stability of the roadway. For the stress concentration area, drilling holes with a depth of 20–25 m are utilized to reduce the pressure, and anti-impact supports are installed in the middle of the roadway. Due to the varying stresses of the rocks around the roadway, partition prevention and control countermeasures are capable of efficiently preventing the instability of the surrounding rock.

Mar 22, 2023

By K. V. Raj, T. Bhowmick

"Control of fugitive dust in high latitude open-pit mines is challenging due to unique atmospheric phenomenon resulting in complicated flow regimes, and atmospheric inversion due to lack of adequate solar insolation during prolonged winter seasons. In this study, two idealized (One conical and one trapezoidal) three-dimensional open-pit mine geometries are simulated for differing seasonal conditions using the CRADLE-CFD package. The airflow is modeled using Standard Kappa-Epsilon Turbulence Model solved by RANS equations. The concept of particle tracking is used to predict the flow pattern of dust particles. For various climatic conditions, and two different pit geometries, fugitive dust particles varying in size (PM0.1 to PM10) and concentration are generated at various locations of a mine and dispersed by the airflow pattern inside the open-pit mine. The amount and location of dust particles inside the pit is reported at various time intervals. The development of atmospheric inversion during the winter season significantly affected the amount of dust retention inside the open-pit domain. While during the summer, airborne dust particles were transported outside the open-pit domain in a short time. INTRODUCTIONComputational fluid dynamics (CFD) modeling of open-pit mines is challenging. In a recent paper, Bhowmick et. al. [1] presented different constraints and challenges in developing a 3-Dimensional CFD model. In order to obtain realistic results from a simulation, however, appropriate values of various inputs are required. Simulation results of a 3D non-hydrostatic model by Shi et al. [2] showed that both the mechanical and thermal forcing are important mechanisms, controlling the development of the atmosphere inside an open-pit. Alvarez et al [3] used a CFD model for predicting dust dispersions in a medium sized limestone quarry, and presented several iso-surfaces of varying dust concentrations using ANSYS CFX. A similar study by Torno et al [4] introduced a more sophisticated parameterization of the dust sources. Flores et al. [5] used an OpenFOAM CFD simulation package to simulate and predict pollutant dispersion in an idealized and an actual open-pit mine in Chile with an intense insolation condition. The model was simulated for three different conditions: (i) air advection (10 m/s) driven mechanical turbulence; (ii) surface heat flux (240 W/m2) driven thermal buoyancy; and (iii) both air advection and surface heat flux driven conditions. The results of the simulations showed that the buoyant currents contribute to the removal of a large percentage of the dust particles. The buoyant currents modify the purely mechanical-turbulence induced flow pattern and reduce the particle residence time, commonly observed in a purely mechanical turbulent flow (non-buoyant case)"

Jan 1, 2015

By Tim Arnold

"Justified is a show on FX that takes place in Kentucky coal country. The two main characters, a cop named Raylan and a criminal named Boyd, are adversarial to the very end, yet they manage to maintain a seemingly inexplicable bond of friendship through it all. The final episode ends (spoiler alert) with Boyd asking Raylan why that is. He responds, “If I allow myself to be sentimental, there is one thing I wander back to” Boyd responds, “We dug coal together.” Fade to black.What creates these types of bonds between friends and co-workers in mining? I don’t know about you, but many of my best friends I met in mining. Certainly the people I respect the most in this world are a part of our industry. Good, honest, honorable men and women. And I am not just talking about the leaders of our industry. I am talking about great miners who taught me how to do the right thing and also be productive.I have had the pleasure to work for some great people and the misfortune of working for some of the loudest screamers. What I consider the worst butt-chewing in my life may surprise you. I once worked for a man I respected, because he showed me respect. He went on a business trip and left some instructions. For some reason, I was able to justify to myself that they applied to everybody but me, and I disobeyed them. When he returned he called me into his office and said to me: “Tim, you pissed me off when you did that.” He said it quietly and with no anger. I had lost his respect. This devastated me more than any screaming shift boss ever could have. I learned a lot about values from that conversation.Most of us will spend more time at work than we will with our families over a lifetime. It is natural that tight bonds be created at work. What I believe makes mining special is that these bonds are so strong. They are strengthened by the incredibly hard work our miners do. They work at all hours, on holidays and in all sorts of extreme weather conditions. The physical demands of the job are sometimes exhausting. Our bonds are further reinforced because the work is dangerous. Not only does management watch out for the wellbeing of their people, but each and every one of us looks out for one another. The bonds are made tight because our people are so passionate about what they do, no matter the department or profession. Finally, they are strong because of the thousands in the industry that keep doing the right thing, every day. We make great friends in this industry because of the strength of character of our people. That is why Boyd and Raylan respected one another so much."

Sep 1, 2016

By R. S. Jurani

Sunshine Mining Company's Kellogg operation is the primary silver producer in the United States, and maintaining a comfortable working environment in this deep underground mine historically has been a complex and costly problem. To improve the ventilation and cooling systems at a time of declining and uncertain silver market, it was proposed to optimize the performance of existing facilities at minimum cost. This paper discusses a 2-year, $400 000 optimization program that resulted in increased total mine airflow, cooler ambient temperatures, reduced compressed air usage, and lower energy consumption by primary fans, air compressors, and refrigeration plants, thereby saving the company approximately $650 000 per year.

Jan 1, 1987

By A. F. Agnew

Discussion by A.E Agnew Strachan's paper summarizes a wealth of data on water-storage dam "incidents" published by USCOLD and ASCE in 1988, together with a review of tailings-dam incidents published by USCOLD in 1994. The data is summarized by text and 11 histograms. The histograms present a useful compilation of these data, although the patterns within the histogram blocks did not survive the Mining Engineering printing process - so their usefulness is impaired. Unfortunately, the text discussion is too cursory and does not highlight the significant relationships among the various causes of the incidents. Four paragraphs of text and Fig. 1 were devoted to water-storage dams, but the discussion is too sketchy, and Fig. 1 is unclear. Important statistics that could be uncovered are: •the total number of dam incidents tabulated were 500+, •earth embankments constituted 73% of those in operation and •incidents related to earth embankments were 75%, of which dam failures accounted for 24%, major repairs accounted for 42% and accidents accounted for 34%. Strachan concluded that "the majority of the dam failures are associated with overtopping (p. 49), and that the majority of incidents are associated with spillway and other facility structures" - although this is difficult to discern from Fig. 1. Confusion regarding Strachan's use of the terms "dam failures" and "incidents" is compounded by his use of "failures" and "accidents" in one paragraph of his Introduction section followed by his use of "incidents" in the next paragraph. Getting to the meat of Strachan's important paper, the tailings-dam incident survey (USCOLD, 1994), the connection between Figs 2 through 11 seems obscure. First, in the four paragraphs of introductory material, one learns that "incidents consisted of failures, accidents, seepage and other incidents of performance that did not meet design criteria" (p. 50). One does learn the helpful caveat that "structures not related to mill tailings were not included in the review" - so that the Buffalo Creek (West Virginia in 1972) and Aberfan (Wales in 1966) coal-mine failures, together with the ongoing metal-mine remediation work at Summitville (Colorado) do not muddy the waters of his paper. The all-too-brief discussion of the data shown in Figs. 3 through 11 (185 dams in USCOLD plus 26 dams in UNEP) reveals the following: •Figure 3: 57% of the incidents (failures and accidents) occurred with dams less than 20-m (66-ft) in height. •Figure 4: 63% of the incidents were due to failures alone (subset of Fig. 3). •Figure 5: Active dams had 82% of the accidents and 93% of the failures. •Figure 6: Types of dams (upstream, water-retention, downstream, centerline and "unknown") separated according to incidents. •Figure 7: Breaks out the incidents in Fig. 6 by failures, accidents and ground water. •Figure 8: Breaks out incidents by type (overtopping, slope stability, earthquake, foundation, seepage, structural, erosion, mine subsidence and "unknown"). •Figure 9: Separates Fig. 8 data into active and inactive dams. •Figure 10: Separates Fig. 9 data into failures and accidents. •Figure 11: Same as Fig. 8, but broken out by tailings-dam type (Fig. 6). Figures 6 and 7 show that most of the failures are associated with upstream or "unknown" types. Figure 9 shows that the leading causes of incidents for active dams

Jan 1, 2003

By J. Hanna, R. Kalathur

Over the years, Alabama's coal industry has generated, during mining and cleaning operations, about 150 million st of fine waste coal, with this total increasing at a rate of 2 million stpy. Reclamation of the fine-size wastes (containing 20% - 60% clean coal by weight) provides, free of charge, mined and crushed feed stocks for coal recovery. Also, the removal or recovery of pyrite from the tailings should eliminate a major source of acid-water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the +100-mesh material produced commercial-grade coal averaging 7.6% ash, 0.8% sulfur and 13,471 Btu/lb. However, the coal yield, at about 31 % - 56%, was relatively low. Froth flotation, using mechanical and froth column methods, gave similar coal products at much higher coal recovery rates of 87% - 93%. This coal analyzed 10% ash and 1.1% sulfur.

Jan 1, 1993

By U. S. Geological Survey Staff

"In 2017, the total estimated value of nonfuel mineral production in the United States increased by 6 percent from 2016 (Table 1). The value of metals produced domestically increased by 12 percent and the value of industrial minerals produced domestically increased by 3 percent. Some metal commodity values (cobalt, magnesium metal and palladium) increased by more than 35 percent in 2017 from 2016 owing to higher prices.Some U.S. metal mines and processing facilities remained idle in 2017, including three primary aluminum smelters in Indiana, Missouri and Washington; a titanium sponge facility in Utah and a byproduct vanadium production facility in Utah. In contrast, new gold mines opened in late 2016 and 2017 in Nevada and South Carolina, respectively, and iron ore mines in Michigan and Minnesota restarted or operated for the full year. In addition, increased oil and natural gas drilling activity led to increased production of some industrial mineral commodities that are used for oil and gas drilling. Production of some industrial minerals, especially those used in infrastructure and residential construction, remained essentially unchanged in 2017, a reflection of the limited growth in construction activity. The production of some metals, including iron and steel, aluminum and other nonferrous metals and nonmetallic mineral products increased. Overall, mining activity trended upward as the result of increases in coal mining, oil and gas extraction and metal mining (Table 2).Discussion of mine production is commonly segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, such as crushed stone or construction sand and gravel, which have higher production quantities but are lower-valued materials. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of natural aggregates are orders of magnitude larger than those for most other mineral commodities, thus making direct comparisons based on weight meaningless (Fig. 1)."

Jan 5, 2018

By S. M. Carpenter

In an ever increasing ?carbon? society; management and growth will be measured by one?s carbon footprint (or output). Industries, especially mining, are under an ever increasing scrutiny of carbon, water and environmental mandates. These mandates are measured by the emissions caused by the combustion of fossil fuels. The fundamental building-block for any business, strategic or management decision must be based on an understanding of one?s ?footprint?. The scrutiny is most stringent for the commodities producers, power producers & fuel suppliers in the energy market. An overview of currently acceptable standards, application of those standards and nuances experienced in collecting the data necessary to analyze and complete a company?s carbon footprint will be presented. A lack of regulation, the fear and expectation of new and ever constraining rules, regulation and a change in the federal administration is a recipe for uncertainty in the marketplace.

Jan 1, 2010

By S. C. Gambrell

The practice of roof bolting in world-wide mining activities is very well known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Discussions of the mechanics involved usually originate with actual experience gained in the use of roof bolts. The use of roof bolting in mines has grown dramatically during the period after World War II. Other scientific techniques have emerged in mining research in the same period. Included in these techniques is the study of rock mechanics, which has now developed into an impressive research effort. Various means of analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that could be easily analyzed. Because of the inherent nature of rock, direct research methods frequently are not certain to provide satisfactory results, whereas indirect methods must idealize a given set of conditions in order to be useful. One of the indirect research methods is the photoelastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various configurations (1,2,3,4,5). Much of the theory used now in the design of underground openings is based on photoelastic evaluation. Unless rigorously applied, how- ever, the photoelastic technique is at best a qualitative means of evaluation. It is useful, however, for unusual examples which can be more or less easily analyzed to obtain the overall state of stress which could not be determined by other means. Little work has been done in the photoelastic analysis of rock bolting, mainly because direct research techniques have proven useful.

Jan 1, 1970

By Michael S. Moats, John Bailey Fletcher

Wear rates of grinding media can be misrepresented by marked ball wear tests (MBWT). Galvanic interactions between dissimilar grinding media can be affected by the chromium content in the media and the presence of oxygen in the environment. Corrosion, one component of wear, can be affected by many variables. Corrosion rates and corrosion potentials for modern high chromium white iron (HCWI) and high carbon steel (HCS) grinding media samples were obtained through electrochemical testing. In this study, the impact of chromium content in the grinding media and the dissolved oxygen in a simulated mill water solution on corrosion rates and potentials was examined. Increasing chromium content in HCWI above 15 weight percent increases the corrosion potential and decreases corrosion rate. Removing most of the oxygen from the solution lowers both the corrosion potential and corrosion rate of the materials tested. The electrochemical results were examined to model possible galvanic coupling effects on corrosion rates. Galvanic coupling between HCS and HCWI could cause differences in corrosion rates for almost all scenarios modeled. Based on the galvanic coupling analysis, MBWT results could be impacted by mixing HCWI and HCS in a ball mill charge. This impact is predicted to be more significant when dissolved oxygen is present in the mill water and as the chromium content of HCWI is above 15 weight percent.

Dec 21, 2022