Search Documents

By C. H. Cheh

The amount of fines in run-of-mine coal has been increasing and coal quality has been deteriorating as a result of the increased use of mechanized and continuous mining methods. Removing the mineral matter and pyritic sulfur from coal prior to combustion will lower transportation costs, improve power plant performance and reduce sulfur dioxide emissions. Since physical cleaning methods can only remove individual particles of mineral matter and pyrite, it is necessary to crush and grind coal to fine sizes to separate these contaminants so they can be removed by deep cleaning processes. The increased portion of fines in run-of-mine coal together with attempts to increase the mineral matter removal efficiency have stimulated interest in fine coal cleaning technology. However, there are many problems to be solved before fine coal cleaning can be applied to power plant coals. These problems include: 1. coal cleaning plant capacity is reduced when conventional cleaning circuits are modifies to deep clean coals; 2. existing equipment and technology is not suitable for cleaning fine coal; 3. coal recovery is reduced; and 4. fine coal is difficult to dewater, dry, handle, transport and store.

Jan 1, 1982

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and point cloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion point clouds with millimetric precision, capturing the structure of the rock mass. The automated point cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors such as site specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using discontinuity set extractor (DSE). Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time. The analysis determined that the automated mapping algorithm was able to identify the same discontinuity sets that had been manually mapped. The automated mapping software mapped an excessive amount of smaller fractures, which caused the comparison of both mapping techniques to be unsuccessful in terms of trace length and spacing.

Mar 19, 2021

By M. E. Rossi

This paper discusses the use of Conditional Simulation (CS) models to provide mill feed grade profiles for different time periods. The conventional approach of classifying block estimates as ore or waste generally does not adequately represent dilution, lost ore and the anticipated grade control data, including variability of mill feed from the pit and possible stockpiles. The detailed simulation of grade control practices can be done, but at the Pre- or Feasibility stage of the project may be impractical, since drawing dig limits on multiple benches is tedious and time consuming. Using the Feasibility Grade Control (FGC) method as developed by the Centre for Computational Geostatistics (CCG, University of Alberta-Edmonton), the CS models can be processed quickly to establish dilution and lost ore, and predict daily or short-term feed to the mill. The simulated nodes can be aggregated into selective mining units with adequate representation of likely geometries to be recovered from the pit, to mimic anticipated selectivity. An example from a large copper deposit is shown. The study provides an estimated stream of tonnages and grades fed to the plant by mining periods of interest and based on a specific mine design and schedule. The resulting cash flows support the economic and financial analyses of the Feasibility Study; also leads to improving mine schedules; and aids in developing blending schemes if necessary. INTRODUCTION The conventional approach of separating mineralized material into ore or waste categories does not always include a realistic amount of dilution and ore loss. Also, often it does not provide a good estimate of the grade that will be fed to the mill. If the grade control estimates are unbiased, they will over the long run represent the long-term average of grades fed to the mill; but the anticipated variability of mill feed from the pit and stockpile sources may be misrepresented. Some references on traditional grade control implementations can be found in Chunnett (1982); Davis et al. (1989); Srivastava et al. (1992); and Nowak (1992). Alternative methods based on economic variables improved significantly on the purely grade-based control methods, see Douglas et al. (1994). Further developments involved the use of geostatistical conditional simulations (CS) and profit models, which in several cases have been successfully implemented (Aguilar and Rossi, 1996; Rossi, 1997; Deutsch et al., 2000; Norrena and Deutsch, 2002; Neufeld, 2005; Jewbali and Dimitrakopoulos, 2009). But they can be impractical, mostly due to the lack of understanding of the methodology involved; even if semi-automatic dig limit drawing is implemented, there is always a need for is tedious and time consuming checking and corrections, even if using a single profit model derived from the simulated grades.

Jan 1, 2019

By Ronald L. Wiegel

In a mineral processing plant there are a number of routine decisions which are based at least in part on the plant's metallurgical performance. Among these are those related to: 1) equipment functioning properly 2) suitable operating conditions 3) reagents achieving desired results 4} determining operating response to changes in ore 5) defining circuits offering potential for improvement A step beyond the routine, are the periodic management evaluations of operating supervision and technical assistance, which are based largely on profit -a direct function of are availability, metallurgical performance and operating costs. The "yardstick", excuse me -"meterstick", by which performance is best measured is the plant metallurgical balance, which tells not only what was produced but how it was produced. Since this metallurgical balance is directly related to both plant profits and individual rewards, it is only reasonable to make that "meterstick" as precise as humanly possible.

Jan 1, 1978

By R. A. Ynchausti

In January 1993, Pyramid Resources began implementation of a supervisory expert control system at a U.S Cu concentrator. The objective of this control system was to improve plant profitability through unit operation optimization and integration. This paper documents the key aspects of the project, including: economic and associated benefits, system architecture, concepts of implementation, process control strategies, practical aspects of implementation and conclusions. The implementation of expert control at this concentrator has resulted in an estimated benefit of $50,500 per day. This is a net result of improved tonnage, reduced reagent consumption, improved concentrate grade and reduced energy per ton produced.

Jan 1, 1995

By Charles W. Daugherty

INTRODUCTION The Washington Metropolitan Area Transit Authority's (WMATA's) rapid transit system, Metro, ultimately will comprise 162.5 km (101 miles) of line divided among 10 routes. As shown in Figure 1, about 24 km (15 miles) of the system will consist of mined rock tunnels distributed along the A, B, C and K Routes. The structural construction contracts for all of the A, C and K Route rock tunnels are complete and trains are running in about one-third of them. A contract for construction of rock tunnel section B-9, the southernmost third of the B Route, was awarded on June 27, 1980. The final design of Sections B-10 and B-lla, the remainder of the rock tunnel portions of the B Route and the Metro system, are well advanced and should be under con¬struction by 1982. Of Metro's 87 stations, 11 will have been constructed by mining in solid rock, a not inconsiderable achievement, since each structure must be over 183 m (600 feet) long, wide enough to accommodate two trains and one or two passenger platforms, and high enough to achieve a stable arching action without encumbering columns. With the passage of years, some original priorities have been reordered, and ways have been sought to streamline and simplify this most complex of Metro structures without grossly violating the architectural standards that make it unique. This paper will summarize that search, and describe the design and construction aspects of the resulting product, the dual chamber rock tunnel station.

Jan 1, 1981

By C. Feng, W. Song, B. Moudgil, P. Zhang, W. Xiao

Separation of dolomite from phosphate is the most challenging problem in phosphate mineral processing. Over 50% of the future phosphate reserves in Florida contains too much dolomite to process using the current industry practice. The FIPR Institute has collaborated with worldwide experts in the field to address this issue. As a result, the industry is now offered with three feasible options. Optional 1 involves crushing and grinding of high-dolomite phosphate pebbles followed by dolomite flotation at slightly acidic pH using a new collector that does not require phosphoric acid as a phosphate depressant, achieving a final concentrate analyzing less than 0.9% MgO at about 87% P2O5 recovery. Option 2 offers three methods for reducing MgO content in the concentrate from the Crago process, including adding a dolomite depressant in the rougher flotation step, dolomite flotation of the cleaner concentrate, and scrubbing the cleaner concentrate in quartz sand. These methods could reduce MgO content in the final concentrate by 20-40%. Option 3 is a gravity separation technique using an innovative separation jig, and may well be the ultimate solution to the problem. INTRODUCTION Magnitude of the Dolomite Problem With the depletion of the higher grade, easy-to-process Bone Valley deposits, the central Florida phosphate industry has moved into the lower grade, more contaminated ore bodies from the Southern Extension. The phosphate deposits in the Southern Extension may be divided into two zones: an upper zone and a lower zone. The upper zone is readily processable using the current technology, but the lower zone is highly contaminated by dolomite. Geological and mineralogical statistics (Hassan and Bogan, 1994) show (Table 1) that more than 50% of the phosphate resource would be wasted if the lower zone is bypassed in mining, and about 13% of the resource would be wasted if the dolomitic pebbles in the lower zone were discarded.

Jan 1, 2019

By R. Michael Craig

The flood basalts of the Columbia Plateau in eastern Washington State are under investigation for suitability in siting a deep geologic repository for high-level radioactive waste. To support safety and feasibility evaluations of the proposed repository construction and operation, an assessment is necessary of the potential for inflow of groundwater to the repository excavations from the surrounding saturated rock. Preliminary estimates of inflow are presented using simple models appropriate to the current understanding of available data. Both normal and bounding analyses are presented.

Jan 1, 1986

By J. C. Haptonstall

The Bismark Mine is located in northern Chihuahua, 150 km southwest of Ciudad Juarez. The ore deposit was discovered in 1979, and was placed in production in 1992. The production rate is about 2400 tpd from an ore reserve of 8.5M tonnes. Grades average about 8 % Zn, 0.5 % Pb, 0.2 % Cu and 50 g Ag per tonne. Substantial inflows of water into the under-ground mine complicate the operation. Complex metallurgy poses another challenge for the operators. Bismark was operated through a joint venture, Minera Bismark, S.A. de C.V., with U.S. and Mexican partners, but since early 1993, it is wholly Mexican-owned and operated.

Jan 1, 1994

By R. E. Lindstrom

The mineral bastnasite is utilized to describe alternate processes for the extraction and separation of the rare-earth elements by solvent extraction. The rare earths can be acid-leached directly or fused with NaOH before acid leaching. Cerium, the major constituent, can be recovered by fractional precipitation, fractional leaching, or solvent extraction with tri-nbutyl phosphate. The latter process is capable of producing 99.5-percent pure CeO2 at 98+ percent recovery. Lanthanum is subsequently recovered by fractional precipitation or solvent extraction with a nitrogen-based extractant. A 20-stage mixer-settler operation with a primary amine extractant results in a 95-percent pure La203 fraction at 96 percent recovery. Europium is amenable to extraction from most of the remaining rare earths with an organophosphate extractant. Selective stripping of the europium, followed by reductive precipitation, produces high-purity Eu203. Another possibility for europium purification involves the differential extraction of europium with an amine followed by a sub- sequent reducing strip. Separation of the remaining elements is more difficult but can be accomplished with amine or quaternary ammonium extracts. Typical separation factors achieved are 3. 8 for praseodymium-neodymium and 10. 5 for neodymium-samarium.

Jan 1, 1967

By R. K. Clifford

The formation of elemental sulfur on the surface of sphalerite in aqueous systems was investigated. Hallimond tube flotation tests showed that unoxidized sphalerite did not float well without a collector. Flotation recoveries of greater than 95 percent were obtained without the use of a collector or frother after the sphalerite had been reacted with oxygen under pressure and water at pH 2.8 at room temperature. High flotation recoveries also resulted when sphalerite was reacted in acidic solutions in the presence of platinum sponge, titanium sponge, 316 stainless steel, copper turnings, or [10-5M++]. Conditions which produced high flotation recoveries of sphalerite yielded contact angles of 37° to 40° and also produced elemental sulfur. The increase in elemental sulfur on the surface of sphalerite was detected by elemental sulfur extraction with petroleum ether, electron spectroscopy for chemical analysis (ESCA), and the electron beam microprobe. The quantity of elemental sulfur formed was insufficient to be detected by infrared or Raman spectroscopy, or by the optical microscope or by the scanning electron microscope. An electrochemical type reaction for the production of elemental sulfur in acidic solutions was proposed. The cathodic reduction of oxygen was the slow step which needed to be catalyzed. A chemical type reaction which produced H2S rather than elemental sulfur was evident in non-oxidizing conditions.

Jan 1, 1974

By Todd Minoski, Matthew McElhinney, Mark Morris, Mark Mazzella, Joseph Bright, Morgan Sears, Craig Compton

To promote the safety and health of U.S. mineworkers, researchers with the National Institute for Occupational Safety and Health (NIOSH) are currently involved in gathering additional field data from the nation’s underground coal mines. The purpose of this field study was to monitor ground movement and changes in pressure during mining where conditions include a thick parting in the coal seam. To accomplish this, three arrays of field instrumentation were installed in the wraparound bleeder of a room-and-pillar panel at the Maple Eagle mine located in southern West Virginia. Borehole pressure cells (BPCs) were used to monitor the change in pressure in pillars located adjacent to the gob. Roof extensometers were installed to measure roof sag at various horizons in the immediate roof, while rib extensometers were installed to measure displacement of the in-seam parting as mining progressed. Additionally, visual observations and manual measurements were taken during subsequent site visits. The repeatability of results, important from a scientific perspective, was accomplished by successfully obtaining field measurements from two nearly identical instrumentation sites. The data collected indicated that the front abutment extent at the edge of the panel was approximately 200 ft, corresponding to a distance of 9– 10 times the square root of the depth. Yielding of the slabbed pillar began when the pillar line was approximately 290 ft outby the instrumentation sites. This was followed by load shedding onto the abutments and the measurement of small amounts of roof sag in the No. 1 entry. Instrumentation data, as presented in this paper, can be used to better understand stress redistribution, pillar performance, and roof/rib displacements. Additionally, this data is suitable for assisting in the calibration of numerical models. Insight gained from applying these models can be used to make better engineering-based judgments for conditions that could potentially be encountered in the future.

Jul 1, 2023

By George K. McCord

It is a pleasure to participate in this Fall meeting of the Society of Mining Engineers to discuss energy conservation trends in the cement industry. Energy is the "life blood" of American industry, and the ability to use available energy resources efficiently may well determine the future of our nation and of its industries. The Federal Energy Administration has classified cement manufacture as one of several energy-intensive industries in the U.S. and has selected the Portland Cement Association to make a detailed study of possible energy conservation measures. Member companies of the Portland Cement Association represent about 85% of the cement producing capacity of the United States and 100% of Canadian capacity. Stated briefly, the purpose of the Association is to extend the uses of portland cement and concrete through research and development, market promotion, education, and public affairs work. PCA's general offices and research laboratories are located in Skokie, Illinois. Our staff of engineers, scientists, and research personnel make the PCA uniquely qualified to perform an energy conservation study of the kind requested by FEA.

Jan 1, 1975

By H. K. Lin

Elemental sulfur is founded to be the predominant sulfur-containing species in a leaching residue resulting from ferric chloride leaching, under given conditions, of a chalcopyrite concentrate. The mineralogical study of the leaching residue which consists of 52% elemental sulfur reveals that the sulfur formed at the end of leaching process is in the form of discrete crystal rather than coating film. Flotation has been applied to recover the sulfur successfully using xanthate as a collector. Dispersants arc needed to prevent the mechanical entrapment of silicate and quartz by sulfur. Very high recovery of sulfur with satisfactory grades can be achieved with a relatively simple notation scheme.

Jan 1, 1991

By Xiaochao Shu, Kun Wang, Fanwei Meng, Rui Tao

Rapidly searching for carbonatite-related rare earth element (REE) mineralized systems is of paramount importance to explorers, because these systems provide the world’s most significant supply of REE. Biotite and barite are suitable indicator minerals that can offer reliable elemental geochemical information used for REE exploration. In this study, we provided an elemental geochemical dataset of biotite and barite from Cenozoic REE deposits in the eastern Tibetan Plateau, and compared the obtained data to those of biotite and barite forming in other geological settings. The F (i.e., fluorine) contents in carbonatite-hosted biotites are highly variable, with biotites from mineralized carbonatite complexes having much higher values (1.05–2.37 apfu, where apfu = atoms per formula unit) than their counterparts from barren carbonatite complexes (≤ 1 apfu). It is therefore believed that the presence of high-F biotites can be regarded as a sign for predicting REE reservoirs. Barites in REE mineralized systems contain much higher (even one or to orders of magnitude) total REE contents (ΣREE >100 μg/g) relative to those species forming in carbonate-hosted fluorite-barite deposits and open marine environments. This means that the high ΣREE concentration of barite can serve as an effective index for REE exploration. The above information is integrated into a REE exploration program in which the areas with strong local tectonism along cratonic edges are priority exploration targets, and high-F biotites and REE-rich barites can serve as direct indices for rapidly identifying carbonatiterelated REE mineralized systems at a strategic distance from other geological settings.

Jun 9, 2023

By J. Villeneuve, M. A. Reute, E. Verhoe

The objective of EU waste policy is to reintroduce used materials into the economic cycle, especially by recycling, or to return them to the environment in a useful state or at least a harmless state. To support decision-making in complex systems, the standardised ISO 14040 life cycle assessment (LCA) method can be used to quantify and to interpret the environmental repercussions of (changes in) a product system from cradle to crave related to a functional service unit. The use of the standardised LCA method at European level can be characterised as a damage-oriented or top-down method, which is often used in product design. Winning, extraction and processing of metals are part of the interconnected worldwide metals production system linked to product design, manufacture and recycling. This complexity cannot be dealt with using LCA. This paper will discuss a dynamic model that deals with this complexity, at the same time providing detailed bottom-up insight into the complex web of materials referred to as Metal Ecology. An example on the replacement on lead in solders will be discussed to illustrate this.

Jan 1, 2005

By E. Tarshizi

Research was conducted to develop a simulation and animation model for an aggregate (sand and gravel) mine operation. This model can assist the mine engineers to investigate and consider the various options of haulage systems which are critical for the mine operation productivity. Discrete-event system simulation studies can be used for the typical haulage issues that mining engineers are often faced with: using truck fleet haulage, conveyor belts, or a combination of both. The simulation has identified some strengths and weaknesses in the current loading and hauling fleet of the mine, and has resulted in some suggestions for improving the system. The simulation includes animation of the operation. Animation is needed to enhance the benefit of any mine simulation model. By combining the visual power of animation with a mine simulation, a complete picture of the mine system is obtained and displayed. The mine is modeled and animated using GPSS/H® and PROOF Professional®, both of which have shown great applicability in discrete mining simulation projects.

Feb 23, 2014

By James Lett

The role of pre-conditioning in a caving operation has multiple benefits, ranging from assisting with improved caveability, normalising fragmentation and improving draw point hang-up frequency. At Newcrest Mining’s Cadia Operations, both the Ridgeway Deeps block cave the Cadia East Panel Cave have utilised pre-conditioning using hydraulic fracturing. Seismic response data inside and outside the pre-conditioned volume show the benefit of treating the full caving block. Cadia East has further developed pre-conditioning to mitigate developing seismic hazards associated with major structures (fault-slip events) and managing mine-wide seismic hazards in new caving operations where the potential for large damaging seismic events exists due to high stresses and hard competent rockmasses. A case study reviewing the impact of pre-conditioning to mitigate seismic hazard associated with fault slip is presented. Cadia East operation undertook a targeted hydraulic fracturing program and reduced the overall number of large events as an example of the benefits of pre-conditioning. This paper will review the application of Hydraulic Fracturing at Cadia and discuss the geotechnical and seismological parameters of seismic events that occur within and outside of pre-conditioned rockmass volumes to demonstrate the benefits that Hydraulic Fracturing bring to future caving operations.

Apr 26, 2022

By C. N. Savage

An industrial minerals review involves an attempt to assemble field and statistical data which are obscure, elusive and incomplete. Often, when me statistical data are available, combining or lumping of commodity values conceals the value of specific items. Personal knowledge of the minerals known to occur in the area of concern, combined with whatever available published data may be compiled, together with careful use of several extrapolation methods, may yield an acceptable summary review of the industry. However, it is particularly hazardous to speculate on future trends and economic aspects because of the many unpredictable variables which may affect the industrial minerals business. Among these variables are the effects of diverse geological conditions, the impact of technological changes (including new uses for minerals not formerly considered industrial types), changing socio-economic factors (including growing environmental controversy), use of substitutes and even recycling of some of the industrial minerals (for example, building materials, lime, etc.). My main objectives are to reveal, as accurately as I can, the state of the in¬dustrial minerals situation, and the effects of possible future developments on this industry in Idaho. Where the words...industrial-tyke minerals, .are used in this discussion, reference is made to selected metallic and nonmetallic minerals and related materials, as well as rock (Table I). Industrial minerals known to be present in Idaho may be listed under general use categories as in Table 1. Some of these commodities are being marketed, have been marketed in the past, or occur in potentially marketable quantities. Mineral fuels are neither mentioned, nor are they considered important in Idaho. Based upon our present knowledge and lack of known, economically valuable occurrences of these commodities, they are considered insignificant (Idaho Bur. Mines and Geology, 1964). Information used for this study is from several sources. Most of the statisti¬cal information should be credited to the U.S. Bureau of Mines Minerals Yearbooks,

Jan 1, 1971

By R. Benito

This paper describes the development of a life-of-mine schedule (LOM) for one of the world's largest known sedimentary copper-cobalt districts located in the Katanga Province, Democratic Republic of Congo (DRC). A particular feature of the Tenke Fungurume LOM schedule is the considerable number of pits/phases for scheduling, each competing to provide the best ore available to a capacity-constrained process facility. This paper discusses the LOM scheduling objectives and constraints, data preprocessing steps such as ore binning, block aggregation and clustering analysis as a scheduling aid, the mine scheduling approach and results and conclusions. Mining Engineering, 2011, Vol. 63, No. 8, pp. 39-47. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011