Search Documents

By N. Ahmed

The collection of hydrophobic particles in the froth phase in flotation has been studied. A continuous flotation cell was developed, in which the froth phase could be isolated from the pulp zone. Hematite particles, d80 = 87 µm, were floated in the pulp, using a conventional oleate collector, while glass spheres of similar diameter, d80 = 82 µm, were introduced in wash water added to the froth. Four samples of glass spheres, with contact angles between 0 and 82 degrees, were used. The results indicate that the efficiency of collection of the hydrophobic particles in the froth can be very high. The process is strongly influenced by the hydrophobicity of the particles and the surface area available for attachment in the froth. Recommendations for the flotation of particles in the froth phase are made, especially regarding the desirable hydrophobicity as reflected in the contact angle, the froth depth, the solids concentration in the feed to the froth, the air rate and the wash water rate.

Jan 1, 2001

By John Chadwick

In the drive for faster development advance rates, railbound systems can be advantageous, in the right application. Skanska BS, the contractor to mine-owner VSK Mining, is driving an adit access deep into the Volouské Urchy Mountain in Slovakia to access the Gemerská Poloma talc deposit, some 70 km (43 miles) west of Ko?ice, the economic and cultural center of eastern Slovakia. Skanska began driving the Stolna Elisabeth drift in February 2007, extending 25 kg/m (50 lb/yd) rails (with 750 mm or 30 in. between sleepers) into the mountain to provide the main haulage to bring talc ore and waste out of the new mine once it gets into production. It will also be used for personnel transport, and is now almost complete. As a second egress and for ventilation, a 2.5-m- (8.2-ft-) diameter shaft of about 300-m (984-ft) depth will be sunk from surface down into the orebody. Stolna Elisabeth is a 4.2-km- (2.6-mile-) long drift mined at a cross section of some 11 m2 (118 sq ft). The finished profile is 3.2-m- (10.5-ft-) wide by 3.6-m- (11.8-ft-) high. It has been developed on a very slight incline so that water runs down it to the portal. The portal is 450 m (1,476 ft) above sea level and the end of the tunnel is 475 m (1,558 ft) above sea level. Much of the rock through which it has been developed is magnesite with a compressive strength of 150 MPA. The drilling jumbo is an Atlas Copco twin-boom Boomer 282 Raildrill drilling 42- to 45-mm- (1.6- to 1.7-in.-) diameter holes to a maximum length of 2.5 m (8.2 ft), depending on ground conditions. This is a drill jumbo that Skanska has used successfully on a number of projects during its life. The condition of the rock through which this drift has been driven is extremely variable. Five classifications of A1 and A2 and B1, B2 and [ ] B3, where A1 is the most competent rock and B3 is the worst, have been established. The amount of support used, of which more later is determined by the classification of ground conditions. At the time of the author?s visit, the project it was about 40 days ahead of schedule, thanks to high advance rates. For instance 6 m/day (20 ft/d) was the plan for the advance to be achieved in B1 rock, but sometimes the crews have achieved 8 m/day (26 ft/d) ? which is the average for the whole project ? in those conditions. In A1 the best advance rate achieved is 12 m/day (39 ft/d). The loading unit is a Häggloader 9HR-B on crawler tracks with a pony track to run on the rails. This allows the unit to be towed up and down the drift along the rails. To load from the face, the Häggloader lowers the foot of its onboard conveyor system to the floor and the backhoe pushes material on to it. This digging arm-conveyor combination produces uninterrupted, optimal volume loading of the haulage unit, without spill ? a technique offering load capacities as high as 180 m3/h (6,356 cu ft/hour). Further-more, as an electrically powered machine, it offers great

Jan 1, 2009

By Paul Headland

The Washington Suburban Sanitary Commission (WSSC) has recently completed design for the Bi-County Water Tunnel Project. The project will include a 10-foot diameter, 5.3-mile long hard rock tunnel located within the Piedmont Physiographic Province in Montgomery County, Maryland. The rock formations present along the alignment are comprised of igneous and metamorphic lithologies. This paper presents the steps taken to characterize the complex geology along the tunnel alignment into a single ?Engineering Unit? based upon the intact rock and rock mass properties. The Rock Mass Rating (RMR) system is planned to be used as the basis for dividing the ground into three ?Excavation and Support? classes. This RMR approach was selected to establish contractual baselines as presented in the Geotechnical Baseline Report (GBR) and is intended to facilitate management of the ground support characterization during construction.

Jan 1, 2008

By E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. This is especially true in surface and underground coal and stone mining where large, noisy equipment predominate. Workers in coal preparation and stone processing plants have also been found to be subject to high sound levels that could potentially cause NIHL over prolonged periods of exposure. National Institute for Occupational Safety and Health (NIOSH) researchers have been conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by river dredging. Little is known about the noise environment and worker exposures in these environments, where processing and mining equipment similar to coal and stone are employed. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to identify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges, in several surface mine sand and gravel operations and in the processing facilities. The locations where workers are likely to be overexposed and were found to be most susceptible to noise overexposures are reported. Results indicate that there are areas on the dredges (crane, suction pumps, and diesel engines) where sound levels greater than 90 dB(A) are present. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration (MSHA) Permissible Exposure Level (PEL) of 90 dB(A) TWA8, laborers, mechanics, oilers, helpers, pickers, and greasers are the workers likely to be exposed to hazardous sound levels and thus develop NIHL over time. Knowledge of the equipment noise, area sound levels, and worker dose levels is information that management and employees can use to reduce exposures. Exposures can be reduced in certain areas through administrative controls and through engineering controls applied to the noisiest equipment.

Jan 1, 2008

By D. Denton, L. Buckingham

The dry grinding and leaching circuits of the Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs. Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes. The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper. The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility. Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike.

Jan 1, 2001

By J. D. Miller, C. L. Lin

Appropriate software and hardware necessary to adapt a x-ray CT analyzer for determination of coal washability has recently been developed and sucessfully tested for well characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed x-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink-float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined.

Jan 1, 2001

By William H. Langer

Large amounts of limestone fines co-produced during the processing of crushed lime-stone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point sources such as cement manufacturing. AWL reactants are readily available, inexpensive and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid. This reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities to within about 10 km (6 miles) of the coastline. The majority of U.S. coastal power-generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufacturers and research scientists. There is a concern that CO2 generated from human activities is contributing to climatic and environmental changes. Approximately one-third of anthropogenic CO2 emissions come from burning fossil fuels to generate electricity. Each power plant is capable of emitting several million tons of CO2 annually. A variety of other industrial processes, such as cement manufacture, oil refining, and iron and steel production, also emit large amounts of CO2. The level of atmospheric CO2 can be reduced by capturing CO2 from point-source emissions and storing or sequestering it in isolation from the atmosphere (U.S. Department of Energy, 2003). In 1999, G.H. Rau and K. Caldeira proposed a geochemistry-based method that is referred to as accelerated weathering of limestone (AWL) in a paper titled ?Accelerating carbonate dissolution to sequester carbon dioxide in the ocean ? geochemical implications.?

Jan 1, 2009

By J. Wright

Since the 1960’s toroidal conductivity has been used to determine the Alumina to Caustic ratio of the digester discharge liquor stream. In recent years the application of ceramic materials have allowed the sensors to moved upstream to provide tighter control of the process. In the Bayer process, dissolving the aluminum contained in bauxite ore in caustic soda and converting it to aluminum oxide produces alumina. An important parameter of the process is measuring the alumina to caustic ratio in the digester discharge stream. The A/C ratio at a given caustic concentration is a measure of the degree of saturation of the alumina in the plant liquor. The aim in the process is to achieve a high A/C ratio. There is however a limit where precipitation will occur if the A/C ratio is too high. For many years conductivity has been used to determine the A/C ratio. Conductivity of discharge liquor is related to the caustic concentration. The change in the caustic concentration is in the same direction of the change of solubility of the alumina. Controlling the conductivity through adding additional bauxite ore and varying the dilution flow can increase plant yield.

Jan 1, 2001

By Michael Rehbock-Sander

The Gotthard Base Tunnel (GBT) is 57 km (35 miles) long and consists of two par-allel single-track tubes with an ex-cavation diameter ranging from 8.8 to 9.5 m (28.8 to 31.2 ft). These are interlinked by cross-passages every 312 m (1,000 ft). Two multifunction stations (MFS) are located in the sections Sedrun and Faido, at one-third and two-thirds of the entire tunnel length (Fig. 1). These will be used for the diversion of trains to the other main tube via tunnel crossovers, for the housing of tech-nical infrastructure and equipment and for potential emergency stops. To reduce construction time, the GBT was divided into five sections and was excavated from several sites simultaneously. The tunnel was excavated from the two portals, Erstfeld in the north and Bodio in the south, and also from three intermediate attacks, with their corresponding access tunnels, in Amsteg and Faido and two vertical 800-m (2,624-ft) deep shafts in Sedrun.

Jan 1, 2012

By Z. T. Bieniawski, José Miguel Galera, Benjamín Celada

TBM case histories from over 400 tunnel sections are analyzed presenting a comprehensive application of the Rock Mass Excavability (RME) index (Bieniawski et al.2006). The paper introduces two new adjustment factors, called the Factor of Tunnel Length and the Factor of Crew Effectiveness, which were established to represent more realistically the interaction of the rock mass characteristics, the TBM parameters and the performance of the crew operating the machine. A new correlation is provided for predicting the average rate of advance of double-shield TBMs working specifically in the double-shield mode.

Jan 1, 2007

By James F. Kvitkovich, George V. Weisdack

Longwall mining techniques were introduced into U.S. bituminous coal mining operations in the early 1960s. These techniques were gradually adopted by many mines during the 1970s. By 1983, considered to be the peak of the longwall mine census, there were 118 active longwall faces in 79 coal mines throughout the United States. Beginning in 1984, longwall faces began a decline in numbers that has continued to the present day (Fig. 1). The geographic distribution of longwall faces today is shown in Fig.2 according to region. A breakdown of recent longwall mine production by region is shown in Table 1. An approximate breakdown of present longwall face installations by product (metallurgical and steam) is shown in Table 2.

Jan 1, 2005

By Bernhard Leist, William D. Leech, Johann Kröyer, Holger Evers

Landsvirkjun—the national electric power company of Iceland—is building the Kárahnjúkar Hydroelectric Project in eastern Iceland. Two glacial river systems will be dammed and channeled through a series of tunnels into a 690 MW underground powerhouse. The Project has a total of 73 km of tunnels to be excavated of which mosthave been completed. From three access adits, three large diameter (7.2 m to 7.6 m),main-beam, gripper-type, Tunnel Boring Machines (TBMs) are being used to complete50-km of the waterway tunnel. Using the TBMs was a first in Iceland to excavate the complex Icelandic basalt formations, which consist of inclined layers of hard basaltic flows with weaker scoriaceous and sedimentary interbeds. Faults, fissures and dykes that frequently cross the lava flows posed both geologic and hydrogeologic difficulties to the TBM tunneling. This paper describes the extreme challenges that the men and equipment had to endure to complete the tunneling, including the harsh winter weather on the surface and the cold, abundant ground water inflows within the tunnels.

Jan 1, 2007

By Keith Jones, Michael Francis

Contract 240 of the Channel Tunnel Rail Link comprises construction of twin4.7 km long running tunnels through a densely populated area of East London. The tunnels were constructed by EPBM in Sands and Sandy Clays, passing 4.4 m below the existing London Underground tunnels, and at depths of 20–30m below ground level beneath the Great Eastern railway lines into London Liverpool Street and a series of railway bridges and hundreds of buildings. This paper describes how the project team managed the challenges relating to the issue of settlement: mitigating settlement effects, prioritising the structures to be assessed, controlling resource expenditure by incentives and flexible response to urgent work relating to unforeseen events such as ground collapse and discovery of unusual structures.

Jan 1, 2005

By Steve Kral

U.S. mines are among the most efficient, productive and safest in the world. Much of that efficiency is due to the high-technology equipment and processes available to the industry. The U.S. mining industry can produce more material now with fewer people than it could a few decades ago. And that material can be produced more safely. However, the workforce is growing older and fewer young people are filling the holes created by retirements. Even though mining is one of the highest paid occupations in the United States, young people believe they can find jobs that pay almost as well without the risks and the often remote locations associated with mines.

Jan 1, 2002

By Florian Häckel, Ulrich Schwarz-Schampera, Benjamin Bühring, Katja Schmidt, Dieter Garbe-Schönberg, KoschinskyM Andrea

"The Vanuatu island arc and its adjacent back-arc basins form part of the southern New Hebrides subduction system in the southwestern Pacific Ocean within a triangle defined by the Solomon Islands, New Caledonia and Fiji (Meffre & Crawford 2001). The back-arc region east of the volcanic front is characterized by three structural depressions namely Vate, Erromango, and Futuna (from N to S), also known as the Coriolis Troughs. Earlier studies of lava compositions reveal the occurrence of highly evolved alkali-rich dacites as well as ankaramite basalts within the individual troughs (McConachy et al. 2005).Here we present the first mineralogical and geochemical analyses of hydrothermal fluids and precipitates (sulfides, sulfates, Fe-oxyhydroxides), sediments, and volcanic rocks, sampled during the "Coriolis Volcanism and Vents" (COVOLVE) cruise SO229 in July 2013 aboard the German R/V Sonne. The samples were retrieved during several ROV Kiel 6000 dives directly from the newly discovered active vent sites at the neovolcanic Nifonea Ridge, and from multiple sites at water depths ranging between 200 to 2800 m within the Vate and Futuna Troughs as well as from the shallow water Epi Caldera NNE of the Coriolis Troughs (Fig. 1)."

Sep 1, 2014

By Larry F. Drolet

Charleston, SC is anything but boring. The city was founded in 1670 and has played a significant role throughout the history of the United States. Located along the coast of the Atlantic Ocean in the southeastern United States, Charleston was a vital city in America?s early existence. Charleston?s coastal location has helped the city become the fourth largest cargo port in the United States and earn the 2011 designation as the number one travel destination in the United States by the Conde Nast Traveler Magazine. Part of Charleston?s charm and beauty can be attributed to its historic structures and churches that line nearly every sidewalk, roadways that were laid out based on the width of horse carriages, great weather, southern hospitality and coastal living. Now imagine the challenges of installing new, or re-placing aging infrastructure, in this setting. Every shovel full of dirt, every stick of pipe and every roadway sub-surface has its own historic story to tell. For engineering minded individuals, Charleston?s infrastructure has almost as fascinating a history as its more visible surface structures. Charleston was among one of the first American cities to construct separate sanitary and storm water drainage infrastructure. This concept has roots dating back to the city?s founding and is a credit to the foresight of its founding fathers who understood the basic health differences between sanitary and storm water.

Jan 1, 2013

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology for supporting the Industry 4.0 has become the target of academic research in many sectors. This study reviewed the trends of open-source technology, its forms, and some industrial applications. As a case study using open-source hardware and software for the mining industry, this study proposed a low-cost environmental monitoring system for non-metallic underground mines to support mine safety and occupational health issues. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device. An open-source software, MIT App Inventor, was used for developing an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a non-metallic underground mining site to assess the performance of the system in both mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors still exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology for supporting the Industry 4.0 has become the target of academic research in many sectors. This study reviewed the trends of open-source technology, its forms, and some industrial applications. As a case study using open-source hardware and software for the mining industry, this study proposed a low-cost environmental monitoring system for non-metallic underground mines to support mine safety and occupational health issues. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device. An open-source software, MIT App Inventor, was used for developing an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a non-metallic underground mining site to assess the performance of the system in both mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors still exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors

By Scott Ellenbecker

The formation in Newmont Mining?s Phoenix Mine near Battle Mountain, NV contains high levels of abrasive quartzite as well as gold, copper and silver. Newmont started mining operations at Phoenix (formerly Battle Mountain Gold) three years ago and the planners knew they were working with a challenging geological formation. But as it turned out, it was more challenging than anticipated. Mine manager Mark Evatz said, ?Anything that touches Phoenix rock wears fast. The rock fights back here.? To contend with the hard conditions, Newmont uses Atlas Copco?s Pit Viper 271 (PV-271) blasthole drill. Because of the hardness of the rock, drilling at Phoenix requires hammer drilling and the mine uses Atlas Copco TD65 hammers with 171 mm (6.75 in.) bits. The mine?s PV-271?s are outfitted with a single 41 m3/min (1450 cfm), 2.4 MPa (350 psi), oil-flooded air compressor. Phoenix has six Atlas Copco PV-271 drill rigs plus an Atlas Copco DML and a DM45 midrange blasthole rig. The mine?s goal is to keep 3.6 Mt (4 million st) of muck in inventory to stay ahead of the shovels and support needed operational flexibility (ore control related). Drilling efficiency has been a continuous point of improvement since operations began at the mine. The single-pass depth capability of 16.5 m (55 ft) on the PV-271 helped with that. Originally, the plans called for 6-m (20-ft) bench heights, supported by 7-m (23-ft) drill depths, and time spent moving from hole to hole was eating up productivity. Drilling on that plan resulted in drilling an average of 14 m/h (47 ft/hour). When depths were changed to 13-m (44-ft) drill depth, supporting blasting of 12-m (40-ft) benches, they were able to use the single pass capacity of the PV-271. Performance increased to more than 18 m/h (60-ft/hour) an hour. Although the drill depth change largely supported the improvement, other aspects of continuous improvement associated with improved knowledge of the Pit Viper drills helped as well.

Jan 1, 2009

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008