Search Documents

By John E. Butler

Due to the present economic climate, particularly the depressed copper market, conventional mining, milling and flotation operations have been suspended. However, due to the apparent amenability of the ore to 'natural' leaching, investigations have been initiated into establishing an in-situ leaching operation as a preferred alternative to conventional operations. Cement copper production has been developed in parallel with the leaching trials and is presently at the rate of approximately 3,000 tonnes of contained copper per annum. Testwork includes controlled leaching of ore both in the laboratory and in-situ following blasting.

Jan 1, 1981

By Robert R. French

Commercial grade gypsum beds up to 16 feet thick is present in southwestern Indiana. The major deposits are found at a depth of 350 feet to more than 500 feet below the surface. The ore body averages about 75 to 95 percent gypsum. Two companies are currently exploiting a deposit which underlies an area of several square miles near Shoals, in Martin County. Another deposit has been located in southwestern Owen County but has not been developed. The Indiana Geological Survey is currently drilling in Greene County and is considering further exploratory work in Perry end Dubois Counties.

Jan 1, 1965

By D. E. Munson

The Waste Isolation Pilot Plant (WIPP) Project was established in 1975 by the Department of Energy (DOE) under Public Law 193 to develop the necessary technology for safe disposal of radioactive wastes from the defense programs of the U.S. The technology development involves extensive theoretical, numerical, and laboratory programs, as well as construction of the WIPP facility in southeastern New Mexico for in situ testing and waste storage demonstration. If after the demonstration, the facility is found to comply with regulations of the Environmental Protection Agency, then the facility will become a repository for Transuranic (TRU) waste. The underground portion of the facility is 655 m beneath the ground surface in massive natural salt deposits of the Salado formation, as shown in Figure 1.

Jan 1, 1991

By D. M. Stephens

Feeder-Breakers were an unknown but much needed piece of machinery when U. S. underground coal mines started converting to more efficient belt haulage of the R.O.M. coal as compared to conventional methods that the 1950's offered. These simple electromechanical machines offered efficiencies in three areas: (1) they contained a surge hopper that allowed a "load' of coal to be dumped without delay; (2) this material was fed horizontally by a drag chain conveyor into a rotating carbide pick breaker that broke all oversize material into a beltable size, and (3) it fed this broken material onto the belt conveyor at a rate conducive to its design. Since its introduction, the Feeder-Breaker has evolved from that first low capacity, low breaking force machine to today's model capable of breaking materials up to 5 MOHS in hardness and having throughput capabilities exceeding 3,000 TPH with availability in the 90 percentiles.

Jan 1, 1985

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Chloride ions and their interactions with two organic smoothing additives – Cyquest® N-900 and HydroStar® 4208 – during copper electrodeposition were explored using cyclic voltammetry and electrochemical impedance spectroscopy. The results revealed that chloride ions, up to a concentration of 40 mg/L, depolarized the copper deposition reaction. A combination of chloride ions and Cyquest N-900 inhibited the depolarization reaction during copper electrodeposition. It is proposed that the chloride ions acted as bridging ligands between copper and Cyquest N-900. Addition of HydroStar at a concentration of 2.5 mg/L depolarized the copper deposition reaction when no chloride ions were present. This behavior did not change with the addition of chloride ions at the concentrations tested, indicating that chloride ions and the polysaccharide do not interact.IntroductionElectrowinning is a major production method used to obtain high-purity copper. In modern tankhouses, copper is electrodeposited onto stainless steel blanks and then stripped, washed and bundled for delivery. Significant improvements in the quality of electrowon copper have been made over the last few decades. Additives, temperature, current density, electrolyte concentrations and agitation are known to influence the quality of copper electrodeposits (Jenkins and Eamon, 1990).The influence of chloride and organic additives on copper electrodeposition has been the subject of considerable research. The addition of small quantities of chloride and organic additives has been recognized to significantly improve the properties of copper electrodeposits. These additives are critical in the prevention of dendrite growth and the production of smooth, dense cathode deposits.Chloride ions have been reported to catalyze the copper reduction reaction and assist in the production of uniform deposits (Lakshmanan et al., 1977; Sun and O’Keefe, 1992). Moreover, it is generally agreed that chloride ions depolarize the copper deposition process at low (several millimolar) chloride concentrations. This is because chloride ions catalyze the reduction of copper (II) ions to copper (I) ions (Cu2+ ? Cu+ + e-) in the rate-limiting step of this process (O’Keefe and Hurst, 1978; Ilgar and O’Keefe, 1997; Hebert, 2005; Shao, Pattanaik and Zangari, 2007)."

Jan 1, 2016

By Amy McBrayer, Andrea Brickey

Limited research has been conducted related to the development of mathematical optimization models for production scheduling at large surface coal mines using the area, i.e., strip, mining method. Increased economic and technical challenges have led to a new interest in production schedule optimization models for these type of mining operations like those currently applied to model underground and open pit mines. While area mines share similar characteristics to both open pit and underground metal operations, neither an open pit nor underground production scheduling model adequately depicts an area mine mathematically. We present an integer programming model with blending constraints and discuss the challenges and opportunities related to the implementation for area mines as well as future research in area mine production scheduling.

Jun 25, 2023

By Grover H. Emrich

Pennsylvania,, due to its location in the humid east, is fortunate to possess within its borders large quantities of water. Most of the State is drained by three major river systems-the Ohio, Susquehanna and Delaware. This abundant supply of surface water has been widely utilized throughout the State, but today other sources of water must be developed due to the increasing demands for water, die largest undeveloped source of water in Pennsylvania is ground water. Pennsylvania is also fortunate to possess extensive coal resources. These coal resources have contributed measurably to the development and prosperity of the States Coal and water's - two valuable resources - have been necessary for the development and industrialization of Pennsylvania, The State needs both resources but can no longer afford to develop one while adversely affecting or destroying the other, We are aware of the effect of coal mining on surface water, but coal mining can also materially affect subsurface water, This effect will according' to the local geologic conditions.

Jan 1, 1965

Mine planners must select a single pit for design with the knowledge that the grades on which this selection is made are uncertain. This uncertainty is often ignored through the use of deterministic models of grade. This makes the mine planner?s job simpler but does not necessarily lead to the ?correct? or ?best? selection. Grade uncertainty is typically modeled with conditional simulation, which generates multiple possible realizations of grade that are equally probable (or improbable). M ethods for incorporating grade uncertainty into mine planning to date have either been perceived as being too complicated, not accessible or too time-consuming. This paper proposes a simple and efficient modeling approach to incorporating conditional simulation into pit optimization, which would be able to be applied in currently commercially available software. An example for R esolute M ining Ltd.?s Syama gold project in M ali shows the range of ore, grade and value outcomes associated with generating pits through a variety of methods.

Jan 1, 2013

By A. Arik

1his paper presents a modified ordinary kriging technique referred to as the "Nearest Neighbor Kriging" (NNK). The method is a simple and practical tool to use when the ordinary kriging (OK) results are unreasonably smooth, especially when estimating recoverable ore reserves for deposits with skewed grade distributions. NNK is robust and globally unbiased like OK. However, it is more advantageous over OK because it can control some of the smoothing and conditional bias which have been the major pitfalls of OK in many grade estimation cases. The paper details the methodology of NNK and its application to a gold deposit.

Jan 1, 1998

By Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources, and resistors. An analogous approach is outlined here for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The modeling technique proposed uses five basic (non-reducible) elements: the H element, the Q element, the D element, the R element, and the N element. These elements are characterized by their (a) pressure gain or loss, (b) air quantity, and (c) pressure-versus-quantity relationship, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine ventilation networks.

Jan 1, 1996

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) has been regulated by the U.S. Mine Safety and Health Administration since 2002 in underground metal and nonmetal mines. To demonstrate regulatory compliance, DPM samples must be collected and later analyzed by the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method, but the FLIR Airtec DPM monitor can serve as a complementary engineering tool. The monitor is a handheld instrument that offers near-real-time measurements of elemental carbon (EC), which is a primary constituent of DPM. As part of an ongoing field study, the monitor was used to survey EC in an underground stone mine. This effort was aimed at determining spatial and temporal DPM variations in several key locations. The results of prolonged area monitoring—that is, lasting several hours — revealed that DPM concentrations were diluted substantially as air moved away from the primary production zone, but that concentrations could vary quite a bit in a single location from day to day and between seasons. DPM concentrations were generally lower in winter than in summer, which is consistent with increased natural ventilation airflows during winter. Using a modified sampling cassette, an attempt was also made to sensitize the Airtec monitor to allow for “spot-checking” of EC concentrations — that is, measurements made in several minutes. Preliminary field data showed that the sensitive cassette performed well in terms of providing accurate data that could be useful for rapid assessment of DPM. IntroductionDiesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It largely consists of elemental carbon (EC) and organic carbon (OC) (Birch, 2003). The World Health Organization International Agency for Research on Cancer classified diesel exhaust, including DPM, as a carcinogen (World Health Organization, 2012). It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition and retention in lung tissue. Because DPM exists in both the micro- and nanoparticulate ranges, it can bypass typical autoimmune defense mechanisms that keep larger particles out of the respiratory system (Ristovski et al., 2012)."

Dec 1, 2016

By Fulian He, Jianhang Chen, Dongdong Chen, Shoubao Zhang

"The Wangjialing Coal Mine is the main colliery of the China Coal Huajin Energy Limited Liability Company. The average thickness of the coal seam in District 201 is 6.21 m. Fully mechanized longwall mining was used in this district. The ventilation roadway of panel 20102 was influenced by the retreat mining of the adjacent panel 20104. Therefore, large deformation and severe roof falls occurred in this roadway, seriously influencing the safety production of this coal mine. To support the roadway, cable truss was proposed to strengthen the reinforcement of this ventilation roadway. First, numerical simulation was used to optimize the reinforcement parameters, including the cable installation angle, cable length, and eccentric distance. Based on numerical simulation results, in-situ tests were conducted in the ventilation roadway of panel 20102 with the cable truss technology. In-situ monitoring results showed that the roof-to-floor convergence and the convergence of roadway on two sides were within the safety range. Furthermore, no apparent separations occurred in the roof. These indicate that based on the designed parameters, the cable truss system can effectively maintain the roadway stability under the severe influence of the adjacent longwall mining.INTRODUCTIONCable bolts are flexible tendons composed of multi steel wires, which are wound into a strand (Chen, Hagan, and Saydam, 2018). They were initially introduced in the hard rock mining industry in the 1960s. Later, they found rapid application in coal mines to maintain the stability of excavations (Wang et al., 2015).The standard cable bolt is composed of seven steel wires with a diameter of 15.2 mm. Laboratory and in-situ tests showed that there is a low bonding capacity between the standard cable bolt and the grout (Craig and Holden, 2014; Chen, Hagan, and Saydam, 2018). Then, modified cable bolts are developed based on the standard cable bolts. They are improved by changing the surface geometry of standard cable bolts, such as birdcaged cable bolts (Hutchins et al., 1990) or nutcaged cable bolts (Hyett et al., 1993). Further tests proved that modified cable bolts have better mechanical interlock and friction between the cable bolt and grout, leading to larger load transfer capacity of cable bolts.Although cable bolts have been used for many years, failure of the cable bolting system still occurs. A common failure mode is the damage of surrounding confining medium while the cable bolt is still hanging in the roof, which is caused by the bond failure of the cable/grout interface (Hutchinson and Diederichs, 1996). To prevent the cable bolting system from failing, the cable truss system is more widely used in mining engineering."

Jan 1, 2019

By George A. Savanick

The objective of this paper is to review advances in the art of borehole (slurry) mining made by the Bureau of Mines. The introduction gives historical and general background information on borehole mining. The borehole mining concept is defined and justified in terms of economics, health and safety, the environment, and resource conservation. This is followed by a description of the design of a prototype borehole mining tool (BMT) developed by the Bureau of Mines. Included are design drawings and performance specifications. The next section describes the application of the BMT in the extraction of metallurgical coal from steeply pitching seams near Wilkeson, Wash., during 1975-76. The field test showed that the BMT produced coal at the rate of 8 tons per hour (tph) (7,272 kg/hr) from a depth of 88 feet (26.8 m) and was effective in producing coal as far as 15 feet (4.6 m) from the center of the borehole. The data are used as a basis for an economic analysis of borehole coal mining and for the suggestions for the design of a second-generation borehole coal mining tool. The following section describes Bureau efforts in applying borehole mining to the extraction of uraniferous sandstone at Rocky Mountain Energy Corp.'s Nine-Mile Lake site, Natrona County, Wyo. BMT design changes appropriate to uranium mining are described along with production, reliability, and reclamation data taken during 1977-73. The field test revealed that the BMT produced 900 tons (81.8x105 g) of uraniferous sand at an average race of 8 tph (7,272 kg/hr) from a depth of 75 (22.8 m) to 90 (27.4 m) feet and created a cavity 25 feet (7.6 m) in radius. These data are used as the basis for an economic analysis of borehole mining of shallow uraniferous sandstones. Reclamation data included will be the results of backfilling experiments conducted at Nine-Mile Lake during 1978. The most significant of these data were that backfill was emplaced at the rate of 16 tph (14.5x103 kg/hr) and that 90 percent of the material extracted from a cavity can be backfilled.

Jan 1, 1979

By J. B. Lott

The authors' company has recently undertaken a development programme aimed at exploring the relationships between the variables of greatest importance in the design of mixer-settlers for metallurgical solvent extraction applications. Such applications vary from relatively small scale plants treating copper mine waters, nickel containing effluents, etc., where the total flowrates may be of the order of a few hundreds of gallons per minute, to very large scale plants treating several thousands of gallons per minute of leach liquors containing copper, uranium or other metals. This paper outlines the physical and mechanical factors which must be taken into account when designing mixer-settler systems for large scam. solvent extraction plants. The performance of the equipment will also be dependent upon the chemistry of the system, including the kinetics and thermodynamics of the ion exchange reaction itself, the effect of impurities flocculants, surfactants, temperature, etc., but these will not be dealt with here. Much of the laboratory work has been carried out using copper containing solutions and either LIX 64* or LIX 64N* as the solvent dissolved in various grades of kerosene. For simplicity, all the graphs and tables of results which are presented and discussed here will refer to the LIX-copper system, although the conclusions will in many cases be generally applicable to other systems also. The LIX-copper process is now sufficiently well known to obviate the need for a full description, however, an outline flowsheet of the process is shown in Figure 1. The ultimate objective of a laboratory programme for a particular extraction application is to provide data upon which a mixer-settler system can be designed to handle a given throughput of leach liquor and extract from this liquor the maximum quantity of metal for the minimum cost. In other words, the objective is to determine the design and operating parameters which achieve the optimum balance between capital and operating costs. * Trade-marks for General Mills solvents.

Jan 1, 1971

By D. J. Torpy

With copper at its host depressed price in several years, producers are looking at every opportunity to cut costs in order to continue operating. Some of the measures that have been applied by different companies include reduction in manpower, high grading, and in some cases partial shutdowns. The most beneficial cost cutting measure implemented by Southern Peru Copper Corporation was to steepen the slope of the final pit limit from a conservative 37 degrees to an average of 48 degrees. By doing so, substantial cash outlays were saved. Southern Peru Copper Corporation (SPCC) operates two open pit copper mines and concentrators in the southern part of Peru, about 150 kilometers from the Chilean bordar. The Toquepala Mine went into production in 1960 and the Cuajone Mine in 1976. Both mines use shovel, truck and train operations. The trains, which haul ore to the crusher or waste to the dumps, are loaded either directly by shovels or by a transfer system. The Toquepala Concentrator treats an average of 43,000 tons per day and the Cuajone Concentrator an average of 55,000 tons per day. Concentrates are shipped via a 200 kilometer railroad to the port city of Ilo where the SPCC smelter is located. The annual production in the smelter from both mines is 290,000 tons of blister copper.

Jan 1, 1987

By Edward S. Plotkin, Gary A. Almeraris, Thomas F. Peyton

The lining of the tunnel and shafts for a new section of New York City's- water system required extensive components to produce, deliver and place a continuous tunnel linning. The project placed approximately 153,000 CM (200,000 cy) of concrete for 5,340 M (17,520) of drill and blast 7.3 M (24 ft.) ID tunnel, located at depths of 152 M (500 ft.) to 213 M (700 ft.) . This section of tunnel will be connected to the surface water distribution system via four shafts of varying diameters ranging from 5.8 M (19 ft.) ID to 1.5 M (5 ft.) ID . All work was done beneath the streets of Manhattan under the rigid constraints of the City of New York and the Bureau of Water Supply regulations.

Jan 1, 1987

By S. Liu

A general account of nitrogen-generating systems, including the surface fixed, surface-mobile and underground-mobile types is presented. These systems have recently been adopted in coal mines in China to prevent and extinguish fires. The paper stresses nitrogen -injection technology and relevant systems of monitoring and stopping air leakage.

Jan 1, 1998

By J. Organiscak

A majority of continuous mining machines employ a water spray system and a machine-mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine-mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays and scrubber airflow on dust and gas levels, while using a 12.2-m (40-ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1-m (20-ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complement the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off-curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010

By J. A. Bradbury

N. A. Degerstrom, Inc. has constructed and operated a processing plant approximately five miles north of Soda Springs, Idaho for processing a byproduct phosphate treater dust from Monsanto's elemental phosphorus plant, also located in Soda Springs. The plant is designed to produce agricultural-grade phosphoric acid, gallium, and silver. The design capacity of the plant is 54.4t (60 st) of treater dust per day, which can produce 16,326t (18,000 st) of phosphoric acid, 6,600 kg of gallium, and 6,033 kg (194,000 oz.) of silver per year.

Jan 1, 1993

By Roger Storry, Arnaud Hochart, David Harris, Olivier Martin

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands under the main shipping channel in Biscayne Bay. Five cross passages (CPs), spaced at 200m centre to centre, provide emergency access between the two tunnels, as shown in Figure 1.The CPs were constructed by open-face excavation methods but the particular geological conditions at the project site (loose and variable carbonate sedimentary strata with very high permeability) required specific ground treatment solutions to provide safe excavation conditions and to ensure the long term serviceability of the permanent works construction. Where access allowed, ground treatment was performed from the ground surface using deep-mixing techniques; however, at two locations (CP2 and CP3) surface access was restricted and ground treatment by freezing, performed from the tunnels, was required. The CPs are 12.3m long with an excavation diameter of 5.8m and are located up to 30m below the water table partly or wholly within the Key Largo limestone (termed Layer S7 in the ground model). Layer S7 is a coralline limestone having a metastable honeycomb structure and high variable porosity. At CP2 the upper portion of the excavation was within the overlying Anastasia Formation limestone (Layer S6), comprising a highly permeable coquina. The geological profile along the project is shown in Figure 2.This paper presents aspects of the freeze design and the risk mitigation necessary to successfully achieve the construction of the CPs in the unique geological conditions."

Jan 1, 2016