Search Documents

By J. K. Pandey, ebashish Mishra, D. P. Mishra, N. K. Mohalik, S. K. Ray

The increasing demand for coal and depletion of shallow depth reserves are pushing towards deeper mining. In deeper coal mines with multiseam workings, the problem of ventilation surges many folds primarily related to air quantity requirement, heat, humidity and spontaneous heating/fire in goaved (gobbed) out areas. The paper describes the design of a new approach to improve the ventilation system of a real-life deep underground coal mine with multiseam workings. For this, the ventilation problem of one deep underground coal mine 6&7 pits Bhutgoria Amalgamated Colliery of Tata Steel Ltd. with multiseam workings has been studied in detail to determine an appropriate solution. A ventilation survey of the mine and computer simulation of the ventilation network has been carried out to reach a practical solution. Ventilation survey results have been analysed to develop a representative ventilation network of the mine for both qualitative and quantitative analysis. Further, computer simulation of the ventilation network of the mine has been performed to virtually verify the application of a highcapacity booster fan in the present ventilation circuit without disturbing the vulnerable areas. Field validation is also carried out after the implementation of the solution in the mine to determine its efficacy. Thus, the findings of this paper can be directly applied for the installation of booster fans to achieve the required air quantity in deep underground coal mines with multiseam workings having spontaneous combustion liabilities of upper seam goaved out areas.

Jun 2, 2022

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

By R. S. Conti, M. R. Krump, C. P. Lazzara Ph. D., R. L. Derick, L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, CO, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward-sloping (20%) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward-sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used, due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results.

Jan 1, 2010

By Donald I. Bleiwas

The U.S. Bureau of nines evaluated the potential availability of tungsten from 57 tungsten mines and deposits in 19 market economy countries (1). The 38 properties that were producing at the time this study was performed contain approximately 375,000 tons1 of W03 (tungsten trioxide). The total estimated recoverable resource from all properties studied, both producers and nonproducers, was 1.2 million tons W03 (demonstrated level). Approximately 143,000 tons of W03 is recoverable from producing properties with costs at or below the January 1983 market prices. The study indicates that by 1990 production from currently operating mines in market economy countries will decrease as their demonstrated resources become exhausted. Some of this potential decline may be offset by lower than anticipated levels of market demand, discoveries of additional resources at producing mines, development of other known deposits, and/or discoveries of new deposits. Development of new tungsten resources in market economy countries will likely result in costs higher than exist at currently producing properties. The People's Republic of China has been steadily increasing production and export of tungsten in various form and currently supplies about 25 pct of U.S. imports. China's tungsten mines are large, high-grade operations capable of producing at relatively low cost. These factors, coupled with China's apparent need for foreign exchange, could lead to further expansions of production and exports from China, with a consequent increased dependence by market economy countries on China for tungsten requirements and a threat to the survival of the market economy countries' tungsten industries.

Jan 1, 1984

By Walter E. Dean

Deep-sea manganese nodules are considered to be potential ores of manganese, nickel, cobalt, and copper. Considerable time, effort, and funds have been applied to the study of Se distribution of nodules on the sea floor and the location of economically important areas, but little effort has been spent in understanding the origin of nodules. Most theories that have been proposed to explain the origin of manganese nodules have been based on inorganic physicochemical processes. It is not by coincidence, however, that the area considered to be most economically feasible is in the zone of high biological productivity in the eastern equatorial Pacific Ocean and underlain by siliceous biogenic sediment. The genesis of manganese nodules and the concentration of many trace elements are intimately associated with biological processes.

Jan 1, 1982

By G. E. Agar

In the April issue of Mining Engineering there is a technical note "New size laboratory ball mill for Bond Work Index determination" written by M. Nematollahi which is very confusing. My recollection is that a description of an experimental procedure should be such that someone skilled in the art should be able to reproduce the results. Applying this test to this particular article would according to me cause a failure to be registered. There are apparently three batch laboratory test procedures referred to in the article. One of these is the traditional Bond test with all its limitations such as dry grinding followed by exclusively dry screening, two attributes which fail to simulate conventional industrial grinding. There is a second procedure (NSBM) which the author is advocating as an improvement of the Bond procedure but from the description I doubt that anyone would be able to repeat the procedure. For instance, is the grinding to be done wet or dry, if wet at what pulp density, and how is the screening to be done, wet or dry or a combination?

Jan 1, 1995

By J. O. Marsden, J. H. Gourdie, J. R. Arnold, J. G. Mansanti

During the testing and design of the Gold Fields' Chimney Creek mine, it was found that a much higher carbon loading was possible with CIC (carbon-in-solution columns) than with CIP (carbon-in-pulp). In an effort to keep the carbon handling minimized, an emphasis was put on forcing gold to the CIC circuit rather than the CIP. After considerable study, it was found that a circuit with two thickeners and an interstage leach would force 90% of the gold to CIC. Computer modelling indicates that the benefits of the hybrid circuit include higher recovery, less carbon handling, fewer leach tanks, and lower reagent costs.

Jan 1, 1990

By D. E. Larson

The U.S. Bureau of Mines has developed a image analysis methodology to correlate the energy consumed during the grinding of an ore to the mineral liberation achieved. Energy consumption values are obtained using a laboratory-scale ball mill equipped with a torque sensor, and an automated image analyzer is used to determine the liberation present in ground products. By combining liberation information with energy consumption data an appraisal can be made of the energy required to liberate the mineral(s) of interest. Results of tests performed on a complex sulfide material determined the effects of grind duration on the liberation achieved and the energy efficiency.

Jan 1, 1995

By H. Mischo, R. Ellmies

Uranium has been mined in Namibia since the 1970s. The worldwide increasing need for energy in the early 2000s has led to the development and opening of a second uranium mine in 2007 and has triggered an increased interest in uranium exploration, often referred to as “the Namibian Uranium Rush.” In all, four mining licenses have been granted by the Namibian Government, which currently has two mines in operation, a third undertaking trial mining and the fourth in project finance negotiations. In addition, highly intensive prospecting activities at additional deposits are at an advanced stage. The finalization of the strategic environmental impact assessment (SEA) on uranium mining in 2010, the first of its kind and scale in the world, has enabled the Namibian government to assess this uranium rush and its tremendous legal, socioeconomic and environmental impacts and to prepare for the different future scenarios conceivable when this article was written in 2011, including both a skyrocketing and a complete breakdown of demand scenario. The Fukushima disaster and plans of the Namibian government to significantly increase royalties and company taxes in 2011 have threatened the market situation, forcing investors to reevaluate Namibian uranium mining projects. However, with the tax and royalty increase initiative since withdrawn, most projects are back on track at this point in time.

Jan 1, 2012

By Atta Ur Rehman, Kwame Awuah‑Offei

This paper examines the effect of bucket geometry (cutting blade profile, floor profile, and blade thickness), speed, motor power output, and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scaled model of a load-haul-dump in full factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated to penetration and draft; muckpile particle size is positively correlated to penetration and negatively correlated to draft (p < 0.0014). The results show that buckets with a semi-spade cutting nose profile yield the highest penetration (mean 118.30 mm) followed by those with the spade (mean 108.88 mm), which also yield higher penetration than those straight blades (mean 95.19 mm). Bucket floor profile and blade thickness had no significant effect on penetration or draft. Also, we determined that increasing the speed and motor power output, simultaneously, can reduce bucket penetration. Thus, operators should not waste energy for no additional gain or even loss in bucket penetration. Also, the work finds speed and motor power output each combine with muckpile particle sizes to affect bucket penetration. This research furthers our understanding of the effectiveness of different bucket geometries in improving penetration and reducing draft for rubber tire loaders.

Oct 29, 2021

By Dmitriy A. Malovichko

The general theory for the description of seismic sources is briefly discussed. The effect of excavations on seismic radiation is considered. Expressions for seismic source mechanisms in terms of the geometrical and mechanical parameters of source processes are provided for the following cases: fault slip and shear failure in a confined environment, dynamic stress fracturing around a tunnel, rock fall, landslide and sudden subsidence. A classification of seismic events in mines based on source mechanisms is introduced. The classification separates blast-, slip- and crush-type events. Various approaches of analysis of source mechanisms involving forward modelling and inversion are discussed. The following examples demonstrating the utility of source mechanisms in mining are presented: forensic analysis of damaging seismic events, assessment of the increase in the depth of failure for dynamic stress fracturing around tunnels and its duration, examination of the rockmass deformation regime, assessment of deformation around tunnels using crush-type events, identification and parameterisation of weak geological structures, stress inversion from slip-type events. Finally, the requirements for seismic data to ensure high quality source mechanism solutions are briefly reviewed and future challenges in the interpretation and utilisation of seismic source mechanisms in mines are speculated on.

Apr 26, 2022

By Huiqin Yao, Dongmei Liu

The study investigated the potential use of low activity circulating fluidized bed combustion (CFBC) ash and phosphate tailings for the production of a filling material based on the cement. The phosphate tailings were used as aggregate and consolidated by cement and CFBC ash. The results showed that the bleeding rate and fluidity of all mixtures decreased with the increasing the amount of CFBC ash. The fluidity of filling slurry is highly related to the experimental factors such as the content of sulfur solid ash, B/A ratio, and mass concentration. The replacement of CFBC ash ranging from 20 to 40% led to a significant decrease in setting time and an obvious increase in compressive strength, but the above effect was obviously weakened when reducing the mass concentration and B/A ratio. The hydrated calcium silicate gel and ettringite generated from the hydration of cement and CFBC ash were the main sources of strength for the filling materials. When the recommended proportion was 1/6 binder/phosphorus tailings ratio, 76% solid content, and 40% CFBC ash replacement, the filling material still met demands on working and mechanical properties; at the same time, the utilization of CFBC ash and phosphorus tailings was maximized.

Oct 11, 2021

By K. Hanna

Early identification of adverse geologic conditions and high stress concentrations during the high-speed extraction of coal using modern mechanized long wall systems is a major challenge facing the mining industry. Often, unexpected geologic anomalies that affect rock mass quality are encountered more rapidly, leaving the mine operator with insufficient time or information to deal with the changing ground conditions. The RockVision3DTM seismic tomographic system, developed by NSA Engineering, Inc., offers substantial benefits over conventional geologic/stress-detection methods and has been used successfully in coal mines worldwide. Tomographic images, produced economically and in near-real time, are easy to interpret, allowing mine operators to deal with potential hazards on a day-to-day basis. This paper focuses on the application of RockVision3DTM technology for delineating hazards caused by stress and geologic anomalies. Case studies for two bump-prone coal mines will be discussed. For example, (1) in a German deep (>1,130 m) mine, the drilling-yield method was used to verify the effectiveness of this technology in detecting stress anomalies ahead of longwalling; (2) in a Polish mine (-500 m deep), two longwall panels 4 km apart were monitored to assess structural and stress-related factors contributing to differences in mining conditions and magnitude of structural failures.

Jan 1, 1999

By Ashish Ranjan Kumar, Steven Schafrik, Oscar Velasquez

Flooded-bed dust scrubbers installed on continuous miners use fibrous type multi-layered filters to capture dust from the airstream. Prolonged operations of the scrubber could lead to filter clogging due to dust accumulation. This results in reduced flow through the scrubber and elevated dust levels in the mine environment. This paper compares the performance of a conventional fibrous screen filter and a novel impingement type dust filter. The impingement filter is a self-cleaning system and was designed to have a resistance similar to the fibrous filter. The cleaning efficiencies for these filters were computed using iso-kinetic sampling and optical counting of coal dust particles in a clean unclogged state. The cleaning efficiency of the impingement filter also increased with an increase in particle size and was comparable with the conventional fibrous filter. The cleaning efficiency of the fibrous filter improved significantly with an increase in water flow. The non-clogging nature of the impingement filter and minimal maintenance requirement makes it an attractive alternative to the conventional fibrous type filter in mining applications. The research also proposes a term called ‘filter performance factor’ to compare the performance of different filters under similar operating conditions.

Sep 19, 2020

By Li Zhang, Jing Zhao, Chuanwei Zang, Shuanlin Wang

The application of gob-side entry retaining (GER) in steeply pitching seam longwall mining with a hard roof has always been a difficult problem. Based on the simplified roof beam mechanical model, the traditional gob-side entry retaining by packing (GERP) roof structure evolution process and its problems with use in steeply pitching seams are analyzed. Therefore, based on the unique characteristics of the gangue rolling and accumulating in the steeply pitching seam, this contribution proposes an innovative method of gob-side entry retaining by roof cutting (GERRC) in steeply pitching seam and details its technical process. The roof structures of the GERRC and the GERP are compared. Taking the Chang Gouyu Coal Mine as a case study, field experiments were carried out. This research finds that the GERRC can both overcome the impact of rolling gangue on roadside support and make the rolling and stacking gangue become a roadside support. The roof structure of the GERRC is in a one-time statically indeterminate state, which is conducive to the stability of the roadway. In the field test, the total displacement of the roadway roof and floor is 97 mm, the supporting pressure of the serried single props is less than 28 MPa, and the props have no obvious bending phenomenon.

May 6, 2020

By Ken Goering

"Bridgestone Americas opened the company’s first U.S.-based giant off-road radial (ORR) tire plant in November. The 139,000-m2 (1.5 -million-sq ft) plant, located on a 222-ha (550- acre) site in Aiken County, SC, will produce radial tire products, including 157-cm (63-in.) tires, used on mining and aggregate haul trucks.The plant, announced in 2011 as a $970-million investment, represents the largest investment that Bridgestone has made in the United States, and is also the single largest investment ever made in South Carolina. Although it had already been producing tires for a few months, the plant officially opened with a ceremony in November 2014, attended by South Carolina federal, state and local elected officials, as well as Bridgestone personnel from the United States and Japan. Prior to the Aiken County plant’s construction, all of Bridgestone’s giant ORR tires were manufactured at its Shimonoseki and Kitakyushu facilities in Japan.Kurt Danielson, president of Bridgestone’s U.S. & Canada Commercial Group, said the facility was built to primarily serve the North American mining and aggregate industries in a more efficient manner. "It’s a real change for us," he said of the U.S.-based plant at its opening ceremony. "This allows us to have a true global presence."The Aiken County plant is intended to allow Bridgestone to meet customer demand for ORR tires, Danielson said. "It really frees up our other plants in Japan to service the rest of the world, allowing us to serve our customers faster," Danielson said. "As soon as we build (a tire), we can have it to our customers."Tires manufactured at Bridgestone’s Japanese plants could spend up to a month in transit to the American continents; from initial mixing of the rubber and other compounds to being warehoused, tires manufactured at the Aiken County plant can be ready to ship in four to five days.Danielson said most of the tires built in Aiken County will be used by customers on the American continents. "We will export," he said, "but our desire is to use as much capacity as we can for the Americas."Ground was broken for the facility inSeptember 2011, when commodity prices were much different than today and global demand for tires had skyrocketed."

Jan 1, 2014

By Staff

In 2012, the estimated value of mineral production increased in the United States for the third consecutive year. Production and prices increased for most industrial mineral commodities mined in the United States. While production for most metals remained relatively unchanged, with the notable exception of gold, the prices for most metals declined. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals? contribution to the GDP increased for the second consecutive year. Trends in other sectors of the domestic economy were similar to those in mineral production and consumption rates (Table 1). After continued decline following the 2008-2009 recession, the construction industry began to show signs of improvement late in 2011 and throughout 2012, with increased production and consumption of cement, construction sand and gravel, crushed stone and gypsum, mineral commodities that are used almost exclusively in construction.

May 1, 2013

By O. M. Arafat, J. A. Finch

Since its development, the functional performance equation for ball milling (McIvor, 1988) has facilitated a new understanding of industrial circuit cause and effect relationships, leading to significant strides in operational performance. Success stories of this approach to plant circuit performance improvement are now too numerous to list. Finch and McIvor (circa 1986) also discovered that the functional performance mill grinding rate at the size of interest was the same cumulative grinding rate that is calculated from mill feed and discharge size distributions using a first-order rate equation. By calculating these cumulative grinding rates for all screen sizes, a complete ball mill model is generated (as used by Finch and Ramirez, 1981). Others in industry, Hinde and Kalala (2009), for example, have noted the same. Lacking the complexity needed to maintain their interest, most researchers have ignored this model, broadly opting instead for Epstein’s (1948) characterization of grinding as a chemical reaction, combining selection rate and breakage size distribution functions. The much simpler ball mill model has previously been incorporated into a proprietary circuit modeling program (McIvor, 2005) and used for plant improvement work (for example, see McIvor and Finch, 2007, and McIvor, 2014). Now, by combining this business-friendly ball mill model with optimization criteria from functional performance analysis, a circuit modeling system (including the needed supplementary steps to assure successful plant implementation of circuit design changes) is at the disposal of every plant metallurgist, grinding equipment/ material provider and circuit designer.

Jan 11, 2017

By Lorraine Brandt Yde

This paper describes development of a cost report that is descriptive, logically oriented, and concise. Since the costs involved relate to mining, this reporting technique could help bridge any possible communications gap between "mining men" and computer personnel, at the same time giving the computer-oriented mining individual information to assist him in his job performance. As computers become entrenched in the mining world, meaningful report assimilation becomes a major task. No one should be more capable of defining required results than the man requesting a report. If he is able to clearly state his needs and has researched his problem, it will be reflected in the computer output. During 1970, The Anaconda Company&apos;s Berkeley Pit Operation, at Butte, Montana, received many different computer-generated equipment cost reports. Up to thirty-six different components for each type (class) of pit equipment contributed cost data to the Berkeley Pit cost system files for both operating and repairs during current month, year-to-date and accumulation-to-date time periods. This reporting approach was taken to facilitate analyzing this voluminous data. SUMMARY A Major Component Cost Analysis (Exhibits 6-A thru 6-C) developed by arranging the top ten operating and repair percentages (component cost divided by total cost) in descending order, and then accumulating these percentages to a possible one-hundred percent. While tabulating the operating and repair cost percentages by equipment unit number in the current month, year-to-date and accumulation-to-date time periods, a frequency chart is constructed for each equipment

Jan 1, 1971

By Hao Zhang, Mi Zhou, Lichun Jiang, Xihong Zhang

This study investigates the roof stability of underground limestone mining in the presence of stratified joints during the excavation process. An analytical solution is derived to predict the stresses and deformation of underground tunnel structures, with the structure simplified as a double-hinge arch. The accuracy of the analytical model is validated through comparison with finite element modeling results. A parametric study is then conducted to assess the influence of different design parameters on the optimization of tunnel stability during excavation. The results indicate that the best stability of the tunnel can be achieved in engineering practices when the applied load (q) is 5 MPa and the joint inclination angle (θ) is 45°, with the roof span and thickness set at either 12 m and 8 m or 15 m and 10 m. These findings provide valuable design guidance for underground limestone mines with stratified joints.

Oct 18, 2023