Search Documents

By Eugene V. Cilento, George B. Georgellis

The hypothesis that freshly-sheared quartz makes it more reactive in lung tissue than aged quartz was tested by its ability to stimulate superoxide anion (02-) release from single adherent pulmonary alveolar macrophages (PAM). Fresh quartz was prepared by grinding for 30 min and then used within 2 hr, while stale quartz was from the same stock but aged 15 days prior to use. Also, dipalmitoyl lecithin (DPL), the major constituent of lung surfactant coating the alveoli surfaces, was coated onto the particles. Release of 02- was measured after 40 and 180 min of direct contact with quartz dust (225 µg/ml). Fresh quartz was more reactive than aged quartz, as indicated by the 78 and 63% increase after 40 and 180 min, respectively. A time delay and suppression of 02- release was observed in the ability of the DPL- coated fresh or stale dust to stimulate PAM. These results supported the hypothesis that the natural process of surfactant coating of inhaled particles in the alveoli may play a role in their phagocytic removal by PAM.

Jan 1, 1991

By S. C. Bandis, N. Barton

During drilling of deep boreholes, local mechanical failures of the wellbore walls may occur due to the inability of the incompetent overburden and reservoir rocks to withstand drilling-induced changes of the stress environment. At present, borehole failure mechanisms in three-dimensional stress fields are poorly understood. Our experimental investigations based on 3-D physical models demonstrate the stabilizing effect of the intermediate principal stress. The latter may play a dominant role in maintaining the integrity of the stress relieving failure zone around the borehole. However, this will depend on the stress anisotropy, the angle of hole deviation and on the angle of internal friction. Our tests also indicate that the failure zone can accomodate high extensional strains. Finally, relations between the physical models and closed-form elasto-plastic solutions are discussed.

Jan 1, 1986

By Thomas F. Martin

Contract 75-124-211 extends along the Chicago River from Roosevelt Road on the south to Ogden Avenue on the north. In addition a branch tunnel runs east from approximately mid-project ending near Lake Michigan. The contract was bid on December 14, 1977 with three joint-ventures submitting bids. Of these the joint venture of J.F. Shea Co., Inc. Walnut, California, (Sponsor), Peter Kiewit Sons' Co., Omaha, Nebraska and Shea Company and Associates, Walnut, California was low with a bid of $101,976,680.00. The MSD awarded the job to the Joint-Venture on January 5, 1978 with a scheduled completion date of January 23, 1983. The project consists of the following major items of work: (1.) A 25'-0" minimum diameter Construction Shaft, 220 feet deep (2.) 13,726 Linear Feet of 30'-0" Concrete lined Tunnel in rock (3.) 6,648 Linear Feet of 13'-0" Concrete lined Tunnel in rock (4.) Seventeen concrete lined Drop Shafts varying in finished diameter from 4'-0" to 12'-0", and each approximately 250 feet deep with chambers and connections to the tunnels varying from 100 to 1300 feet in length.

Jan 1, 1979

By Ben L. Seegmiller

The basic compression-yield concept of roof support for mine roadways requires that the mine roof be placed in a state of compressive stress. The compressive stress may be achieved using a support system such as an entry truss or other specialty truss device. Furthermore, the roof must be allowed to yield, but with great resistance when abutment loads are placed on the roadway. The resisted yielding may be provided using a new yieldable steel prop, known by the trade name, YIPP~. The yieldable steel prop can allow as much as 1.5 m[5 ft] of yield, or up to approximately 40% of the opening height, while providing a resistance in excess of 60 mt[66st]. More than fifteen mining operations including coal, trona and hard rock mines have field tested the YIPPI . Present results indicate that the yieldable prop provides a cost-effective alternative to wood cribs, concrete cribs, hydraulic props and other steel prop supports. The paper describes the YIPPI including its unique principle of operation, its applications and actual field performance.

Jan 1, 1992

By H. Polat, M. Polat, S. Chander

A high shear treatment step was observed to improve flotation of coal. The effect of high shear treatment (HST) was a strong function of coal rank, however. For the low rank coals the HST produced loose, open-structured agglomerates which decreased the entrapment of ash minerals. For the high rank coals, the high shear treatment promoted detachment of low-floating particles from the agglomerates that ordinarily formed in a flotation cell. The extent of agglomeration and detachment of particles from the agglomerates was a function of the amount of dodecane and coal rank. To obtain desired efficiency of separation ethylene-propylene oxide block co-polymers were used. The results showed that the HST-flotation technique increased the ash rejection considerably for both high and low rank coals, though the mechanisms were different.

Jan 1, 1995

By Ronald B. Gabitzsch, Norbert P. Hanke

During 1982, record advances have been achieved in the excavation of vertical shafts with a V-Mole (a vertical shaft boring machine). The V-Mole, supplied by Wirth GmbH in Erkelenz, West Germany, has been used in West German coal mines since the early seventies, mainly for the construction of internal shafts. In 1981, it was brought into the United States for the construction of a series of ventilation shafts with depths varying between 512 m (1680 ft.) and 622 m (2040 ft.) excavated to 7.0 m (23 ft.) diameter. These shafts were needed for the development of coal mines for Jim Walter Resources, Inc. in Brookwood, Alabama. After a description of the mechanized shaft excavation system with the V-Mole, the conditions and parameters, such as ground, shaft dimensions, and linings are discussed. These factors are important considerations for a technically and economically feasible utilization of the V-Mole. In addition, the advantages and disadvantages of using the V-Mole technology in comparison to other shaft construction methods are evaluated.

Jan 1, 1983

By B. Whitmoyer, J. Tian, J. E. Sneckenberger, M. A. Jerabek, C. A. Chandler

A computational procedure has been developed to determine the lung volume function for the upper airways of the human respiratory system. This analytical procedure computes a person's partial lung volume from an experimental two-microphone acoustic measurement of the upper airway passages obtained through a molded tubular mouthpiece. The theoretical transfer function for the two microphone signals as well as the related acoustic impedance and reflection coefficient for the upper airways are calculated using two-channel spectrum analysis techniques. An inverse spectrum analysis scheme then converts the reflection coefficient to an impulse response from which the airway area function is extracted using an area recovery algorithm. Numerical integration of the upper airway area function yields the lung volume function for the upper airways of the human respiratory sysytem. A software program to accomplish this computation of human upper airway volumes will be described in this paper. Application of this computational procedure to the measured tracheal acoustic impedances of 15 human subjects will illustrate the program's capability toward early detection of lung dysfunction using a prototype clinical facility.

Jan 1, 1991

By Meliton M. Garcia, Satya Harpalani

This paper discusses the results of an investigation carried out in an underground mine to characterize the volatile by-products adsorbed on airborne particulates following the detonation of four common explosives including ANFO. The primary objective of this study was to determine if any organic amine compounds, particularly nitrosamines, and any polycyclic aromatic hydrocarbons were produced and trapped in the dust that a miner might inhale during the workday. The production of these substances is of great concern because of their suspected carcinogenic nature. The results of the study indicated that a large variety of the by-products are adsorbed on the particulates generated, and thus remain airborne following the detonation of explosives. The major by-products retained by the dust were bis(2-ethylhexyl) phthalate, and aliphatic hydrocarbons with carbon chains ranging from C12 to C28. One explosive, a water gel, produced the polycyclic aromatic compound, trimethylnaphthalene. No nitrosamine compounds were detected.

Jan 1, 1989

By Joaquin Marti, Peter A. Cundall

This paper reports on some recent work in which several schemes were developed to model jointed rock under high stress, with particular reference to the phenomenon of "block motion" observed during dynamic loading of underground structures. Three approaches were made, corresponding to an increasing relative importance of internal block deformations as compared to rigid block movements. The first one uses distinct element method and assumes internally rigid blocks, which can break, repeatedly, whenever an empirical crack criterion is met. In the second approach each block is allowed three degrees of freedom to deform internally. The third approach, still in the development stage, permits arbitrary deformation of all blocks, which are internally decomposed into finite-difference zones and automatically rezoned during slip to preserve the calculation accuracy on joints. The last two schemes allow arbitrary constitutive relations for the intact rock, and all three schemes permit the geometrical arrangement of joints to be arbitrarily complex, in contrast to normal Lagrange, finite-difference programs, which are unsuited to model discontinua.

Jan 1, 1979

By J. Alton Burks, Robert R. Stein

This paper focuses on the noise exposure levels of miners employed on longwall production faces. Along with the increased production from longwall units has come the potential for greater noise exposures. Typical noise levels are given for the various noise sources that are present on modern longwall faces. Exposure times have typically increased since the introduction of longwall technology in this country. Representative exposure times and patterns are analyzed. Possible solutions are presented for generalized cases. Engineering controls developed by the Bureau of Mines are explained and their potential effectiveness is calculated for the cases presented. The role of hearing protectors in an overall hearing conservation program is also investigated. Recent research performed by the Bureau suggests that the actual performance level of muff -type protectors may be less than the manufacturers ratings under certain circumstances. The use of muff- type protectors is discussed and analyzed with respect to their use on longwall operations.

Jan 1, 1992

In the early days of minimal environmental protection awareness and unreasoning economy development pressures, little attention was paid to growing environmental concerns in Fuxin colliery, especially the air pollution problem due to the long term mining activities. In order to determine air quality concentration levels, a new technique for synthetic assessment of ambient air quality by using the extension of matter-element method is proposed in this paper. The air pollutants data such as Sulphur Dioxide (SO2), Carbon Monoxide (CO), Nitrogen Oxides (NOx), Total Suspended Particulates (TSP), Particulate Matter (PM10), and dustfall collected at four different air quality monitoring stations located in four districts of Fuxin colliery is used. The results obtained indicate that TSP, PM10, dustfall and SO2 are the predominant pollutants. Other pollutants such as CO and NOx are also detected in Fuxin colliery. The air pollution comes mainly from industrial emissions, mining activities and the abandoned gangue stockpiles. Compared to those applied to other mathematical assessment methods, it is demonstrated that the extension of matter-element model is quite appropriate for air quality assessment.

Jan 1, 2006

By R. M. Damodaran

The flotation performance of Florida phosphate rock was evaluated in terms of the mixing behavior of reagents and particulates during anionic conditioning of phosphate slurries. The various conditioning variables that influence mixing, namely, solids loading, agitation speed and conditioning time, were investigated to determine their effect on reagent coating of the particles. The phosphate recovery was used to monitor the conditioning efficiency. The mixing characteristics of the phosphate feed were evaluated in terms of the ratio of the mixing power (P) to the minimum power (Pm) required to keep the slurry in suspension. It was found that mixing conditions govern the conditioning time required to obtain a high recovery. Reagentization was slower at lower P/Pm ratios. At higher P/Pm ratios, the flotation recovery was optimized, and the agitation speed was found to have no significant effect. Optimum mixing conditions were obtained for a74 wt% slurry at an agitation speed of 450 rpm (47 radians/sec). Under these optimum mixing conditions, the collector dosage required for an improved recovery was lower and the conditioning time was shorter.

Jan 1, 1997

By N. I. Aziz, B. Srinivasa Rao, R. N. Singh

The control of respirable dust and its subsequent exposure to miners is essential for improved safety in longwall mining. The extensive variation in face conditions and operations of longwall make numerical modelling an attractive approach in both the development and evaluation of dust control devices. Three dimensional finite element computational fluid dynamics code FIDAP was used to model air velocities and the effect of dust control techniques on dust concentrations at a typical longwall face. The effect of shearer body on airflow characteristics in a longwall face was analysed with both antitropal and homotropal ventilation systems. Path traces of particles introduced near the shearer drums was also simulated. Initial modelling results were validated using field trial results at three operating longwall faces. Results of simulations tallied very well with the field results.

Jan 1, 1993

By J. M. Mutmansky, Y. J. Wang

The method usually used to predict the direction of flow in a connecting airway is to conduct a survey of the two existing nodes to be connected by the new pressure airway. It is then assumed that the air will flow from the node with the measured higher pressure to the node with measured lower pressure. This paper examines this direction-of-flow problem using properties of the system characteristic curve for a two-terminal network and specifies some conditions that will ensure that the air will flow in the direction anticipated. It was concluded that the only requirement is that all characteristic curves of the fans in the network should be strictly decreasing. Five numerical examples illustrate some important proper- ties of the direction-of-flow problem.

Jan 1, 2000

By J. M. Keane

The Solution Mining review arrived too late to appear in the May issue. Solution mining, in its broadest definition, includes all forms of leaching where a lixiviant solution is brought into contact with a metalliferous or non-metallic ore and the resulting pregnant solution is processed for recovery of the valuable soluble material. Technologies such as dump leaching, heap leaching, stope washing and in situ lixiviant solution injection and recovery fit into this definition of solution mining. A publication entitled the US Gold Industry (Dobra and Thomas) reflects the major impact that solution mining techniques have had on precious metal recovery. In 1989 (the last year for which statistics are available), the United States passed Australia to become the third largest gold producing country in the world after South Africa and the Soviet Union. It is estimated that when the final figures are in for 1990, the US will probably pass the Soviet Union in gold output. If the state of Nevada is ranked as a separate country, it will rank fourth in the world in gold production for 1990. A good proportion of this increase in gold production over the past few years can be attributed to the application of solution mining technology to low-grade, precious-metal-bearing material. Solution mining techniques have also made inroads in copper production. Many operations located at former underground mine sites employ in situ leaching as an adjunct to conventional dump and heap leaching practices.

Jan 1, 1991

By Timms. Greg P., John W. Bennett

A field-based method for measuring the diffusive oxygen flux through covers placed on sulfidic waste rock dumps has been developed and applied at a number of mine sites. The technique provides a means of quantifying oxidation rates in dumps and can thus be used to assess the effectiveness of cover systems. Two instruments can be used. The first is portable and easy to set up, enabling a picture to be built up of the overall diffusive flux into a dump by making measurements at a sufficient number of locations. The second is installed beneath a cover and is preferred in situations where oxygen is consumed in the cover since it provides a direct measurement of the oxygen flux into the underlying waste rock.

Jan 1, 2000

By J. B. Hiskey, P. H. Qi

Activated carbon loaded with gold from different halide solutions was characterized by thermal analysis (TA) techniques. The mechanism of gold uptake by carbon varies from predominately adsorption for gold iodide to predominately reduction for gold chloride. Thermogravimetry analysis (TGA) and differential thermal analysis (DTA) measurements confirm the existence of adsorbed gold-halide species within the micropore structure of carbon. These results suggest that the ratio of reduced to adsorbed gold increases for gold halides in the following order: Au-I < Au-Br < Au-Cl. In the case of Au-I, TA results for the loaded carbon were compared with pure compounds of 12, Aul and Aul3.

Jan 1, 1998

By G. Schriever, H. Thiel, E. J. Foell

A long-term, large-scale, disturbance-recolonization experiment with relevance to the environmental effects of deep seabed mining is described. The study is funded by the German government and was launched in the abyssal eastern tropical South Pacific Ocean in February-March, 1989. After obtaining pre-impact baseline environmental data, a 10.8 km2 (4.2 sq miles) circular area of seafloor was disturbed using a specially designed "plow-harrow" device. An initial post-impact sampling series was carried out immediately after disturbance followed by a second post-impact sampling series six months after the disturbance. Plans call for repeated visits to the site at two year intervals to monitor the anticipated slow recolonization process until the area is inhabited by a new, stabilized community.

Jan 1, 1993

By Prasad Kummarapurugu, Maija Teijonsalo, Sirkka-Liisa Jamsa-Jounela

There has been a significant progress in the use of mathematical modeling and simulation in the minerals industry in the last decade. Process models have moved from academic world to important industrial tools. This paper reviews the status of mineral processing simulators and recent progress in simulator development and applications is discussed. The simulation for process design and optimisation is now an established technique, as evidenced by its increasing use of practising engineers through commercially available simulator software. The paper presents a systematic approach to the process study procedure for the control system development, clarified by practical case examples calculated by SimCon - a novel steady-state simulator for mineral processes. Examples of the application of SimCon in drawing flowsheets, calculating mass balances and making simulations for grinding and flotation processes are presented. At the end of the paper, the state-of-the-art and the future of computer-aided pro- cess study at mineral processing plants is discussed. Keywords: Simulators, modelling, object oriented programming, computer aided control system design

Jan 1, 1996

By C. E. Capes

Reduction in the quality of resources and attendant increase in the quantities of fines to be processed present a major economic and environmental challenge for resource - based industries. It is becoming evident that agglomeration by immiscible liquid wetting will play a significant role in the treatment of these fines. Liquid phase agglomeration can be adapted to separate solids or liquids in highly divided form from liquid suspensions and emulsions. Diverse opportunities in coal fines recovery, novel fuels technologies and oily waste water treatment are cited here. The oil agglomeration of extreme fines from coal tailings, with consequent dramatic reduction in refuse for disposal, is now a commercial reality. It is suggested that this approach can serve as a prototype for the processing of extreme fines in an economical and environment ally sound manner.

Jan 1, 1989