Search Documents

By Thomas Oberndorfer

Recent publications indicate that there is a rising interest in the field of mining method selection, and increasing efforts are being undertaken to develop satisfying solutions. Yet, computer assistance for mining method selection (MMS), or in other, terms assistance in the (pre-)feasibility state of a project, still lags behind the computer application in other mining activities. This is true for research as well as for application. This paper is intended as a contribution to the development in computer-assisted mining method selection, and focuses especially on underground hard-rock mining. It is structured in four main parts. The first deals with general aspects of mining method. selection within the process of mine planning, and with problems and requirements which derive from this specific situation. In the second part some numerical MMS-approaches hitherto published are briefly introduced, and investigations on these approaches are discussed. Based on .these experiences, in the third part an analysis of the complex system MMS is presented. It focuses on heuristics, influencing factors, objectives, assessment-routines and mining methods, and emphasizes the essential necessity of a profound mining method description (MMD) specially developed for the requirements of MMS and numerical processing. Accordingly the fourth part of this paper presents a mining method description model developed at the Department of Mining Engineering, Montan-University Leoben (MUL), Austria. It describes the consequences of the investigation, in particular the new mining method description model, on 'the design of a MMS-system. The paper closes with a outlook on the possibilities of an successful MMS-system being realised.

Jan 1, 1992

By K. S. E. Forssberg, M. I. Hallin

In many cases, the reuse of process water in flotation plants is desirable both for plant operating reasons and for environmental protection. The main advantages are better housekeeping of fresh water and process chemicals together with the reduction of polluting species to the environment. There are however a number of problems involved in the use of recycled process water. The main problem is that recycling sometimes has a deterious effect on the process and can occur months after the start of water recycling. The Division of Mineral Processing of Luleå University of Technology has been conducting experiments on recycling of process water at various sulphide plants in Sweden for over ten years. The experiments have been carried out in pilot- and full industial scale, in collaboration with the mining companies operating the plants. Until 1988 investigations were carried out in four different sulphide plants. The objectives of the experiments were: first to document differences in the composition of the process water during recycling; secondly to investigate any changes in the pulp chemistry of the flotation circuits wich may be due to the influence of recycled water; and lastly to establish critical levels, if any. of the parameters measured. While conducting experiments of this kind several things have to be kept in mind. Normally, recycling is done by using tailings pond water as process water. This means that time effects are important, because of the time lag between water input in the tailings pond and the reclaim of that water back to the plant. As will be shown, the

Jan 1, 1989

By S. D. Morrison, J. L. Watson

It is well known that the density and viscosity of a mill pulp have optimum levels for grinding efficiency, and sophisticated control loops are employed to control pulp density in industry. However, these control loops rely on a number of plant measurements, and often the input data will not permit effective determination and control of the mill pulp density. The use of a single remote pulp density measurement has obvious advantages, and it is suggested and demonstrated for laboratory batch grinding that mill noise measurements can indicate the effective density of the mill pulp. In addition, the mill noise is shown to indicate the actual effective pulp viscosity in the mill and hence permit the identification of the dynamic rheological regime existing in the mill. It is demonstrated that mill noise increases with grind time and, at any given grind time, with increasing pulp density in the pseudoplastic range. This increase in mill noise level with pulp density is interpreted as indicating a decreasing pulp viscosity. The results show that the transition from dilatant to pseudoplastic conditions within the mill, with increasing pulp density, can be identified by this increase in mill noise. When the pseudoplastic pulp started to exhibit yield characteris- tics, the mill noise fell dramatically. The technique of mill noise analysis is then used to investigate the effect of a grinding additive on the batch grinding of two ores. With a magnetite ore, the additive was shown to increase the mill noise, and hence decrease the pulp viscosity, in the pseudoplastic region and to increase the effective grinding. The molybdenite ore, however, did not show significant noise level changes and did not show improved grinding efficiency.

Jan 1, 1987

By Joseph Fernandez, Luminita Calin

INTRODUCTION The Tunnel and Reservoir Plan (TARP), commonly known as the Deep Tunnel Project, is the daring and unique concept developed by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) as a two-phase solution to the problem of waterway pollution and basement flooding due to sewer system backups created by the combined sewer over-flows (CSOs). Phase I, primarily for pollution control, includes the tunnels, shafts, connecting sewers and structures. These Phase I facilities intercept, during wet weather events, the CSOs within the MWRDGC TARP service area. The tunnels and shafts provide temporary storage of the CSOs for subsequent treatment at Water Reclamation Plants (WRP) before discharging into waterways. Ultimately, upon completion of Phase II, the tunnels, located from 45 m(150 ft) to 100 m (330 ft) below ground, will convey the CSOs to reservoirs for storage until WRP capacity is available. Phase II, which includes the reservoirs, pumping facilities, additional tunnels and shafts, has been planned to serve a dual purpose. The reservoirs provide storage of excess flows during wet weather events, those beyond the WRP capacity. Following the wet weather events, the stored flows can be conveyed, at controlled rates, to the WRPs for full treatment. These excess flows previously would have resulted in both overflows into the waterways and eventually backups in the local sewer systems. The storage capacity of the reservoirs also will promote the full utilization of the conveyance capacity of the tunnels and shafts, which in turn results in optimizing the conveyance capacity of the existing sewer systems. Therefore pollution control is further enhanced by allowing for capture of a greater volume of CSOs and greatly minimizing backups in the local sewer systems. The TARP project consists of four systems: O’Hare, Mainstream, Des Plaines, and Calumet, covering a total area of 971 km2 (375 mi2) and serving the City of Chicago and 51neighboring communities as shown in Figure1. With only two contracts left before completion of the Phase I tunnels, the 12.7km (7.9mi) Torrence Avenue leg, to be awarded in 1997, and the 12.4km (7.7mi) Little Calumet leg unfunded as of yet, both part of the Calumet System, the pollution control phase of the project is now 86% complete (Table 1).

Jan 1, 1997

By J. H. Calder, J. C. Hower

Three lithotypes of Phalen coal from Cape Breton County, Nova Scotia, Canada, were subjected to a modified Hardgrove grindability index (HGI) test. The testing scheme differed from conventional (ASTM D-409) Hardgrove testing by, in one case, repeating the test three times prior to removing the -200-mesh fine coal from the Hardgrove mill, and, in a second test, removing fines after each of three successive Hardgrove tests. Only the first stage of the latter testing scheme actually conforms to the standard HGI test. All processed samples were analyzed petrographically by a combined maceral/microlithotype analysis. The increase in the percentage of coal ground to -200 mesh increases through the 60- to 180-mesh fractions for each of the lithotypes for the following two apparent reasons. First, with progressive grinding, more of the oversize material is close to 200 mesh (75 µm), creating a "pool" of particles ready to be ground to -200 mesh, and, second, the removal of fines from the system at each step eases the grinding at the successive step. The fines retained system shows the influence of buffering of further grinding by the particles retained in the grinding mill. The Phalen lithotypes and the series of Central Appalachian coals, evaluated previously by Hower and Wild (1994), differ in that an increase in vitrite and a decrease in trimacerite is observed in successive -200-mesh fractions in two of the Phalen lithotypes. This is the opposite of the trend observed in the slightly lower-rank Central Appalachian coals.

Jan 1, 1998

By Ralph J. Anctil, James E. Palmer

According to relatively recent estimates by the US Geological Survey and the US Bureau of Mines, there are more than 0.9 Tt (one trillion tons) of remaining identified coal resources in the seven major western US coal-producing states and about 200 Gt (220 billion tons) in the demonstrated reserve base. Considering coal's current national production level of 0.7 Gt/a (0.8 billion tpy), these US reserve and resource figures are reassuring. Given here is a preliminary analysis of geologic constraints and an estimate of their effects on mining and recoverability of western coal. Mining Constraints USGS and USBM coal figures incorporate only thickness and depth, and are "blind" to many other major geologic constraints on mining and recoverability. The most important of these geologic constraints include: • coal seams too thin or too thick for conventional mining methods; • coal seams that cannot be mined due to insufficient separation from underlying or overlying previously-mined beds; • unstable or otherwise unfavorable roof strata; • soft or heaving floor strata; • coal seams that are too lenticular or discontinuous for conventional mining methods; • coal seams in intensely faulted areas; • coal seams having high angles of dip precluding the use of conventional coal mining methods; • coal seams that cannot be mined due to proximity of water-bearing strata; and • coal quality problems such as excessive ash, sulfur, chlorine, or sodium. Coal Thickness Present USGS-USBM classification for reserve base includes bituminous coal beds more than 0.7 m (28 in.) thick and subbituminous beds more than 5 m (60 in.) thick to depths of 305 m (1,000 ft). Both of these thicknesses are less than the thicknesses now considered mineable in the western US. The lower limit for bituminous steam coal in deep mines is about 1.5 m (5 ft). For subbituminous coal, a thickness of at least 2.4 m (8 ft) is generally required. Accordingly, the Bureau of Mines reserve base includes many thinner coal seams that will not be mined in the foreseeable future. Within the Powder River Basin of Wyoming and Montana many seams-Wall, Upper Pawnee, Lower Pawnee, Cache, Manning-range in thickness from 7.6 m (25 ft) to more than 30 m (100 ft) and occur at depths to 305 m (1,000 ft). These have been included in the Bureau of Mines reserve base. However, the mining technology required to mine these thick seams does not now exist. It will require many years for development. The ultimate recoverability from these thick seams is unknown, but could be as low as 25%.

Jan 8, 1982

By Steve Kral

"Gold rush" is usually associated the western United States - California, Nevada, and Colorado. The southeast section of the nation is known more for its rice, textiles, tobacco, indigo, and cotton. This area, though, is where it all began with gold in this country. The United States' first gold rush, in fact, is said to have started with the discovery of a 7.7-kg (17-1b) nugget in the Piedmont section of the Carolinas in 1799, some 50 years before the rush to California. The Carolina gold rush continued intermittently through 1942 when the Federal Government shut down all gold operations. Strong gold prices throughout the early part of this decade and new extractive technologies spurred a small resurgence of gold operations in South Carolina. Mind you, this is not Nevada with its flood of geologists and mining companies. Nor are there any 7.7 kg (17 lb) nuggets being discovered. But Ridgeway Mining Co., a joint venture between Kennecott Corp. and Galactic Resources, has set about mining 51 Mt (56 million st) of low-grade ore containing an estimated 43.5 t (1.4 million oz) of recoverable gold. The open pit, carbon-in-leach operation is located near the town of Ridgeway in South Carolina, about 32 km (20 miles) north of Columbia. Carolina gold North and east of Ridgeway, Piedmont Mining Co. operates the historic Haile gold mine near Kershaw, SC. And Brewer Mining Co. operates the nearby Brewer deposit. Between 1829 and 1942, South Carolina gold mines produced 10 t (318,800 oz) of gold. It all began in 1799 when Conrad Reed, son of a German immigrant farmer, found the 7.7 kg (17 lb) nugget in Little Meadow Creek, NC. His father thought the rock was worthless and used it as a doorstop, so the story goes. It took nearly three years before Conrad's father decided his doorstop was indeed gold. Gold was later discovered in the Greenville district of South Carolina. And, in 1828, Benjamin Haile discovered gold in a stream that ran through his property in Lancaster County, SC. Haile's mine became South Carolina's most famous and most productive gold mine, producing more than 7.8 t (250,000 oz). At first, miners worked the stream beds of Haile's property. Later, lode deposits were discovered on slopes alongside the creeks. They would lease 4.6 ml (50 sq ft) lots and mine as deep as 7.6 m (25 ft). During the Civil War, the Confeder-

Jan 1, 1989

By S. A. Hoenig

Introduction In an earlier publication, the application of exoelectron technology to the monitoring of dry grinding in a ball mill was reported. Recently, the author has investigated the ball mill problem in more detail with the system shown in Fig.1 . Here, some of the current generated in the ore-ball-water mixture was picked up by the metal chains and served as a measure of the rate of grinding. While the mechanism of current generation has not been completely clarified, a parallel study of electrical effects associated with rock drilling indicated that the major driving force is the zeta potential*, while oxidation of the freshly fractured material provides the remainder of the current. Both of these effects are sensitive to the exposed surface area, and it might be expected that the observed currents would provide a measure of the grinding rate. This "surface area" effect allows the measurement system to be used in any type of rock or ore grinding. Some studies with sulfide copper ore indicate higher currents than those observed with silica sand, but the overall pattern of current versus grinding rate is essentially the same. Experimental Studies The experimental system was set up as shown in Fig. 1. The initial studies were done with silica sand because of its availability and for comparison with the data of reference 1. The sand was sized to an average of 425 µm (40 mesh); a typical charge consisted of 2.5 kg (5.5 lb) of sand, 0.85 L (0.22 gal) of tap water and 2.5 kg (5.5 lb) of iron grinding balls 25.5 mm (1 in.) in diameter. For a typical "run," the mill was loaded with a fresh charge of ore and operated for periods ranging from 10-60 min. During this time, the current was measured with a Keithley 417 picoammeter and a chart recorder. At the end of the grinding period, the charge was removed and sieved to recover the 425, 300, and 212 pm (40, 50, and 70 mesh) fractions which were then drained and weighed. A fresh charge was used for each test and every attempt was made to keep the draining and weighing processes uniform. *The zeta potential is the voltage developed between the surface of a solid particle and the ion solution in which it is immersed. In the case of rock/ore materials in water, the zeta potential is negative.

Jan 1, 1984

By Frank Hagar, George M. L. Robinson

NTRODUCTION The Resource Conservation and Recovery Act and CERCLA (SUPERFUND), in many instances, has had an adverse economic impact on the hardrock mining industry. Over the last few years, many abandoned and active mining operations have been added to the Environmental Protection Agency (EPA) National Priority List (NPL) . When the property is placed on the NPL the operator or EPA is required to conduct extensive environmental assessments to determine if historical mining practices have degraded the existing environmental. If degradation has or will continue, the responsible party is required to implement appropriate remedial action plans. If a responsible party is not identified, the EPA implements a cleanup program. Experience has demonstrated abandoned and active mining operations are subject to RCRA, and possibly Super- fund, if the mine has not adopted appropriate hazardous waste disposal management procedures. If off-site contamination has occurred, the operator will be required to mitigate the impacts and will be required to adopt additional procedures to minimize future impacts. Since the passage of RCRA and Super- fund, many mining operators are adopting management procedures to monitor and inventory hazardous sub- stances and wastes generated, stored and disposed on site. Many operators are in a difficult position because ore, waste rock, process chemicals or other solid waste, in many instances, can be classified as hazardous waste. If the process or other solid waste is deemed to have the characteristics of a hazardous waste, the operator can inventory and adopt appropriate, in- expensive management procedures. However, if the ore or waste rock has hazardous waste characteristics, in- expensive control technologies are impossible to implement. Since existing statutes and regulations require hazardous waste control, the operator will be required to inventory, characterize and monitor all aspects of the mining operations including but not limited to exploration, mining, ore processing and waste disposal. During this process, geological, geotechnical, geochemical, waste and ore volumes, and process materials must be tracked throughout the mining process. To accomplish this task, the most cost effective method to maintain documented and accurate records, is through the implementation of an integrated database management system. The database management system can be used to model and simulate the entire mining operation and if necessary, used to predict whether the operation is in compliance with existing regulations. The developed database can also be used to operating optimize mining and disposal costs.

Jan 1, 1987

By H. Knorre, A. Griffiths, J. Loroesch

Introduction Hydrogen peroxide is known to the mining industry as a powerful oxidant, able to attack and to destroy cyanide, the most important leaching reagent (Knorre and Griffiths, 1984; Griffiths, 1988; Griffiths, 1988). CN- + H202 => OCN- + H2O The most recent development, however, is the use of H202 as an oxidant in the cyanidation of precious metals. This application may appear to be a contradiction to the above mentioned detoxification process. This can, indeed, be the case if certain conditions are not considered carefully. Degussa has developed a new process to enable the application of H2O2, in this field without having any detrimental effect on the cyanide. The incentive to seek an oxygen supplier like H2O2 instead of air was the fact that one of the most important conditions for the fast dissolution of gold is the presence of physically dissolved oxygen in the pulp (Kydryk and Kellog, 1954; Warstell, 1987). 2 Au + 4CN- + 1 /2 O2 + H2O => 2 [Au(CN)2]- + 2 OH Complete gold recovery within a reasonable leaching time may only be achieved if the pulp is saturated with dissolved oxygen. Gold losses in leach operations mainly occur due to the following reasons: • In some cases, the saturation of oxygen in the pulp cannot be achieved by aeration due to the difficulty to transfer oxygen from the gaseous into the liquid phase. This happens, for example, in pulps with a high viscosity. In such cases, even violent aeration only results in a low concentration of dissolved oxygen in the pulp. • In any case, the starting phase of leaching requires the highest amount of oxygen. Therefore, it is especially important to raise the dissolved oxygen level to saturation in the starting phase. Peroxide assisted leach process (PAL) The intention of the process is to introduce oxygen in a liquid form. As a result of intensive research work, it could be shown that hydrogen peroxide can be used as a source of oxygen in the leaching of gold ores. To avoid side reactions, the following conditions must be applied: • Hydrogen peroxide must be diluted before it is added to the pulp. • The dosage of H2O2, must be properly regulated based on the oxygen level of the pulp. • An important part of the continuous 02-control is a special oxygen electrode, which resists the extremely abrasive action of the pulp.

Jan 1, 1989

By Guy G. Jr. Granger

INTRODUCTION Due to the current depressed state of the mining industry, many mining companies have been forced to operate at less than maximum capacity. This paper will describe how the AMAX Henderson Molybdenum Mine and Mill near Empire and Parshall, Colorado respectively have utilized operations scheduling and budgeting to achieve production targets at minimum operating costs The AMAX Henderson Molybdenum Mine and Mill have been operating most recently at approximately sixty percent of maximum capacity. OPERATIONS SCHEDULING Production Targets. The production targets are tons, operating days, tons per opera- ting day, head grade, recovery, and pounds of molybdenum. One specific objective of operations scheduling is to meet the production target for pounds of molybdenum. Present market conditions dictate that production be adjusted to match sales of molybdenum. Over-production and creation of molybdenum inventories is unacceptable. In summary, the product ion target for pounds of molybdenum must be met, but not exceeded. Capacity. The AMAX Henderson Mill single stage open crushing circuit capacity is 48,000 dry short tons per day. The AMAX Henderson Mill single stage semi-autogenous primary grinding mill circuit capacity is 38,000 dry short tons per day. All other AMAX Henderson Mi 11 circuits such as rougher flotation, regrind, cleaner flotation, lead leach, filtering, drying and concentrate handling are sized to accommodate the 38,000 dry short tons per day and pro- ducts from same. The tailing delivery system is designed to accommodate tailing from a 38,000 dry short tons per day operation. Constraints. One mill production scheduling constraint is that the mill operating schedule must be the same as mine production, ore haulage and crushing. There is a total crushed ore stockpi1e storage capacity of 240,000 dry short tons. This breaks down to 60,000 dry short tons of crushed ore over the three reclaim pan feeders for each of the four primary grinding mill circuits. However, there is only approximately 10,000 dry short tons of live crushed ore available over the three reclaim pan feeders for each of the four primary grinding mill circuits. Dozers must be utilized to re- claim and push the other crushed ore. Primary grinding mill throughput is

Jan 1, 1986

By R. E. Muller, L. G. Martin, J. M. Stonehouse

Erratic distribution of values in free gold ore bodies presents severe problems in sorting material in large scale open pit mining. However, an intense program of modern blasting techniques and less than modern gold panning results in good sorting at Houston International's Manhattan mine. Blasting technique is important. If the sample location cannot be relocated because of blasted material movement, information acquired while drilling is useless. So short benches are critical to minimize dilution. Though not very accurate, panning allows for rapid analysis. The more accurate fire assay does not provide the needed speed. Panning can be fairly accurate and errors made are mostly on the low side. Samples of mixed and broken stockpile material are used as checks on pit procedure and to develop stockpile content in¬formation. Added tonnages discovered offset the higher labor costs of this careful sorting technique. The mine is located in central Nevada's Toquima Range in the small mining town of Manhattan, 322 km north of Las Vegas. The mine has four epithermal stockwork ore bodies that are mined in two pits. The mine problem was that conventional ore control was not separating ore from waste. Assays of 6-m blast-holes were used on 5-m centers. The blastholes were relocated by stadia survey after blasting. Holes assaying above the cutoff grade were flagged and mined as ore. This system is practical and useful in high concentration ore bodies or in evenly disseminated mineralization. But it was not practical at Manhattan because of large gold particles and small ore pocket sizes. Ore pockets were often missed when drilling a grid area for blasting. Also, large gold nuggets made assay results unreliable. The probability of a nugget being contained in an assay charge is small. So most results were low, compared to actual grades mined based on stockpile samples. When a nugget found its way into a fire assay charge, the result would be far higher than the actual grade of material represented. In addition, disturbance by blasting created problems in relocating ore. Because of these problems, the grade control program was intensified in September 1979. It successfully separated ore and waste in blocked out ore areas and located more ore in "waste" areas. Known reserves mined to date have increased up to 50% on some benches. The methods used are modern blasting techniques, detailed assaying, and traditional panning of samples collected from active mining faces. These methods allow mining flexibility, to match the variable mineral occurrence in ore bodies. The united effort of the geology and engineering departments has been important to the program's success.

Jan 12, 1980

By Malcolm Reeves

The heavy oil reservoirs of Alberta and Saskatchewan include sequences of unconeolidated silts and fine sands which respond in an unusual manner when subjected to the high temperature and pore-fluid-pressure associated with steam injection and other thermal enhanced recovery techniques. Apparent transient connections are suddenly established between producers and injectore and there is an associated enhancement in oil (and sand) production. These phenomena have been attributed to local fluidization and piping processes which are known to occur in situations where high pore-fluid-pressures prevent the mobilization of intergranular friction. These breakdown processes may be associated with the penetration of tongues of the heated reservoir fluids with suspended sand into the creep sensitive intact reservoir since the viscosity ratios are sufficiently high for viscous fingering instability of the fluid-fluid interface. A program of laboratory tests has been carried out to measure the strength characteristic of saturated oil sands at a variety of temperatures and fluid pressures. These tests suggest, that in common with the coarser Athabasca sands, the Waseca sands have very little cohesive strength and show the characteristic dilational failure response of dense sands. Some special tests, devised to determine the relative ease with which samples can be fluidized, confirm the expected susceptibility of the fine- sand silts. Both piping and fluidization can be readily induced at in-situ reservoir temperatures and pressures. Analysis of stresses around wellbores suggests that fluid-pressure gradients may be sufficient to initiate piping and that backward erosion along streamlines may link producers and injectors. Such pipes may act as well “adits” gathering oil from the heated reservoir and contributing to enhanced production rates. Mechanical breakdown of the reservoir by drilling, injection and production processes provides a consistent possible explanation for the sand-cut response of production wells.

Jan 1, 1986

By Michael Chender

Introduction Clearly, many problems confront the minerals industry today. Yet, at the same time, there is too much energy spent bemoaning the negative effects of difficult economic circumstances, low metals prices, and adverse government policies. These are factors that cannot be altered by individual mineral company reactions. In fact, as we look to the future, the only thing we can be certain of is that we will continue to be faced with uncertainty. Thus, an area that demands close scrutiny and that can significantly affect a company's performance in the future is the posture it adopts to deal with uncertainty. This paper looks at how strategies are developing to deal with this issue. It also examines some of the implications that implementing such strategies have for the role of the individual explorationist. Elements of strategy Whether mineral company strategies are based on diversifying or retrenching, on emphasizing primary production or downstream integration, there seems to be increasing agreement that in the current environment strategies must have several features. They need to be information-based - developed out of access to timely and complete data and analysis about proposed directions and competitor activity, rather than simply following a current fashion. They need to be flexible - adaptable in light of changes in the marketplace and an unpredictable industry. And they need to be cost-efficient - making the most of limited resources. Whether a company is looking for gold financing opportunities, acquiring polymetallic prospects, or doing grassroots exploration for diamonds, these three elements are increasingly essential. They not only allow the company to pursue its current goals most expeditiously, but also open it to hearing and using feedback in the most constructive way. The company can then improve or change strategy as it proceeds. And it can be best positioned to take advantage of opportunities as they arise. These elements of strategy place great emphasis on the skills of the individual. The need for critical intelligence and the reduced amount of capital available to manage are making it more obvious that exploration is a "people" business. This is in accordance with a general trend in many sectors of industrialized economies, reflecting the widely discussed shift from smokestack to information-based industries. Increasing the odds There is a direct connection between successfully implementing the approaches to strategy discussed above and encouraging and improving the quality of work of the individual explorationist. To illustrate the importance of this, some commonly quoted figures on the odds of discovery success can be used. These figures are arbitrary but illustrative. Assume that one out of 100 exploration prospects actually turns out to be a promising ore body, and that one out of 1000 becomes a mine. Based on our research, chances are the most of those

Jan 1, 1986

By James J. Fallen

In this paper we are going to look at some things that may happen to the industrial minerals industry in the next decade. First, some concepts and definitions. What are industrial minerals? Not everyone agrees on an answer to this. So let's look at some of the opinions. Some say that industrial minerals are non-metallic minerals. As you well know, metallic minerals are used as a source material for metals. Copper, lead, and zinc are extracted from metallic minerals. But, some metallic minerals are also used for other reasons. Bauxite is used as a source of alumina and aluminum. It is also used as proppant in well drilling, as an abrasive, as a refractory material, and as a source of aluminum-based chemicals. So bauxite is both metallic and nonmetallic. There are other examples, too. Bastnasite is a source of rare earth metals and alloys but its concentrate is used in fluid cracking catalysts. Phosphate rock is an industrial mineral when used for fertilizer, but it is also the source of phosphorus. Ilmenite and rutile are sources for titanium dioxide pigments as well as titanium. So the nonmetallic designation is not adequate to define industrial minerals. Some say industrial minerals are called such because they are consumed in industry. How about your cat's litter box? Is that industry? Huge amounts of montmorillonite, attapulgite and other sorbtive minerals are pelletized and calcined to make animal litter. Doctors are trying to get people to cut down on their salt consumption. They are against people eating industrial minerals. When diamonds are a girl's best friend, they are not industrial minerals; when they are grinding and polishing media, they are. These examples show that industrial minerals are not exclusive to industry. Regardless, here is my list of industrial minerals: Abrasive Materials - Bentonite Antimony (Oxide) - Borates Asbestos - Calcium Carbonate Attapulgite - Diatomite Ball Clay - Dolomite Barite - Feldspar Bauxite (and Alumina) - Fire Clay Fluorspar - Pyrophyllite Fuller's Earth - Rare Earths Graphite - Salt Gypsum - Sand and Gravel Kaolin - Silica Sand Kyanite - Soda Ash Limestone - Sodium Sulfate Magnesite - Spodumene (Lithium) Magnetite - Sulfur Mica - Talc Nepheline Syenite - Titanium Dioxide Perlite - Vermiculite Phosphates - Wollastonite Potash - Zeolites Pumice There is some overlapping. Fuller's Earth takes in some attapulgite, bentonite, and other minerals, depending on the market. Some would like to distinguish industrial minerals by the market emphasis they receive compared to fuels, metallics, and precious metals. But even there, strict logic fails. Some industrial minerals are commodities. They are sold on a price basis against industry product specs, usually in large volumes. Phosphate rock, potash, sulfur, salt, soda ash, and other materials fit this category. Some are almost custom-designed for end-use and meet performance specs. These are sometimes called functional or specialty industrial minerals. Examples of these are ground calcium carbonate, water-washed kaolin, cosmetic grade talc, filtration grades of diatomite, perlite, and vermiculite. To determine prospects for the decade ahead, regardless of our

Jan 8, 1984

By Anders Sellgren, K. Hansson, A. Jedborn

In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore. from a system's point of view, slurry transportation would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alternative examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasibiliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. 1. The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then temporarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe- line, and personnel are needed. In a first phase (Fig. 2). a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1990

By K. Bragg

During the last several years considerable discussion has taken place on the long term aspects of uranium tailings management. These discussions have centered around a variety of topics which in turn lead to a variety of opinions. In order to come to grips with the various differences of opinion and points of view, the Atomic Energy Control Board has decided to prepare, as an interim measure, a list of proposed close-out criteria for uranium tailings management facilities. It is important to keep in mind that the criteria set out in this paper are proposals and are intended to initiate a continuing dialogue between the uranium mining industry and the various regulatory and government agencies. It is envisaged that this dialogue would continue for a period of from six to twelve months after which some final form of these criteria would be issued and applied to the active uranium mining facilities. In attempting to understand the reasons why the Atomic Energy Control Board has decided to propose these criteria now instead of at some future point in time, it is necessary to look at a number of existing facts. One of the most important of these is that something in excess of one hundred million tonnes of tailings currently are placed in various tailings management facilities. Furthermore, the rate at which tailings are being deposited into such management facilities is on the increase and this increase is expected to continue over the next five to ten years. The management of these tailings is currently covered under the Mine Facility Operating Licences issued by the AECB. Implied within these licences and supporting documents leading to them, are requirements for the conceptual approach to be used at abandonment. There is however, no current requirement for a detailed study on the engineering or financial aspects of such abandonment procedures. This is a gap which the Board feels must be addressed. There are, at this time, various initiatives underway both in Canada and within the international community which are attempting to address the problems and concerns of the very long term management of tailings. For example, current research in Canada which is composed of two components, one by the AECB dealing with purely regulatory aspects and a second major coordinated program under the direction of the Department of Energy, Mines and Resources and in particular by CANMET is going to deal with the technical problems. On the international scene

Jan 1, 1980

By Tim Neil, O&apos

Finnish mining traditions date back 400 years. The country was then one of Europe's major iron producers. Most of the mines in current operation, however, were started during the last 20 to 30 years. The Finnish mining industry must make do with limited resources. Deposits are usually low grade and small in size. Open-pit methods are used where possible. But thin ore bodies and harsh winters can impose severe restrictions. Underground mining is often the only option. Despite these handicaps, Finnish metal miners produce copper, nickel, zinc, vanadium, iron ore, cobalt, and ferrochrome. Ironically, the success of Finnish mining is rooted in a crisis the industry faced several decades ago. Mining costs were rising. High grade mineral deposits were nearly exhausted. It was vital that Finland develop new mining machinery and methods that afforded higher productivity. Cooperation between the Finnish mining industry and its equipment manufacturers was good. Partly as a result, the Finnish mining industry has turned itself into one of the most modern and efficient in the world. The Finns did this while continuing to meet the stringent safety and environmental requirements in force in the Nordic countries. Today, the share of domestic raw materials used by the Finnish metallurgical industry is decreasing. So the country increasingly depends on imports of ores and concentrates. To better provide these imports, Finnish mining companies have expanded their foreign operations. And, while importing raw materials, the mining industry has been exporting its technological and equipment know-how and expertise. Mining methods Conventional mining methods and machinery are used in surface mines. Drilling is the exception. It is done with Tamrock hydraulic track drills and 100 to 150 mm-diam (4 to 6-in.-diam) drill holes. Pumpable slurry explosives are used in larger open pits. Underground, sublevel stoping with open stopes is the most common mining method. It accounts for about 80% of all underground stoping. The main benefits of this method are low production costs, high mechanization, and easy control. The best productivity figures exceed 10 t (11 st) per man-hour, including all mining personnel. The development of cable bolting has made it possible to use sublevel open stoping even in relatively weak rock. Cut-and-fill methods, such as concrete-pillar stoping, inclined-wall stoping, and traditional cut-and-fill have also been used, combined with sublevel caving and room-and-pillar methods, according to local demands. Various fill materials and stabilization components have been investigated and tested for cut-and-fill methods. Sublevel open stopes are often later filled, to stabilize the surface or to allow pillar recovery.

Jan 10, 1988

By Kim W. Wright

Introduction Mining operations require maps for each phase of project development. Engineering plans, cross-sections, and isometric drawings are also needed. Maps are used for geologic interpretation, reserve estimation, permitting, property acquisition, site studies, development work, and production. Maps and drawings are essential to mining. They provide needed information. Generating these products, however, requires many manhours. The filing and organization of maps and drawings is cumbersome, due to their size. Major map changes can necessitate the production of entirely new documents and, thus, additional manhours. The volume of maps and drawings generated in the life of a single project can be extensive. For example, some utility companies have data bases containing more than a million individual maps (one reported eight million). These problems were considered necessary evils in the past. Now, with the automation of map and drawing production, improvements can be realized. Computer-aided mapping and design offers a new approach for the production, management, and storage of drawings and maps. This approach promises benefits in time management, productivity, efficiency, and flexibility. In all economic projects, the bottom line is cost reduction. And implementing computer-based mapping and design techniques can lower costs and increase project profitability. AM/FM/CAD/CAM Automated Mapping/Facility Management (AM/FM) and Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM) are becoming buzz words in the engineering world. Most relevant to mining are the concepts of AM and CAD. These terms relate to the application of computers, specifically computer graphic technology, to mapping and design. CAD refers primarily to the design of components and structures in two and three dimensions. But it can apply to the three dimensional modeling of mine workings, ore bodies, and geologic structures AM refers to the automation of conventional map production. AM/CAD systems use computers to store, manipulate, produce, and update drawings and maps in two and three dimensions. Ideally, the calculating capabilities of computers are also used in conjunction with design and drawing generation, offering capabilities not available with conventional, manual mapping and design processes. To better understand concepts associated with AM and CAD applications, the understanding of a few computer-related terms is necessary. Table 1 explains some of these terms. System Features The capabilities of AM/CAD systems are based on viewing transformations. These are the basic, manipulative tools by which AM/CAD packages generate visual representations of data. Examples include the rotation of a three-dimensional object through space, the expansion or contraction of maps to fit a given scale, enlargements of small areas on maps or drawings for detailed viewing, and the generation of cross-sections from three dimensional data. AM/CAD systems incorporate data base management in their architecture. This allows a user to modify, move, delete, or manipu-

Jan 6, 1985

By Song Jiang, Xianzhi Tan, Minjie Lian

"The ground water heat pump system lades underground hot water which can be heated or cooled by heat exchanger in water source heat pump air conditioner. This system replaces the model of heating of air-conditioning by refrigerator and boiler. In this paper, the formation conditions of hot water energy in Shan Dong are analyzed in order to achieve the purpose of energy conservation and emissions reduction by taking full advantage of water resources such as water pouring and return water of beatification during the productive process of underground metal mine. In order to analyze the issue better, the paper points out some ways and methods for geothermal water often used in underground metal mine. This paper also presents the advantages of the technology of water source heat pump that is applied into underground metal mine. Here is a case study of comprehensive utilization of water source in a certain underground metal mine in Ji Ning. This mine, according to its own actual situation, designs heat pump heat exchange system which is used for indoor heating of buildings and bath for staff. It turns out that the system can save 23% water per year, cut down 3.303 million KW electric energy, and reduce 4160t emission of carbon dioxide. It is concluded that the technology of water source heat pump has broad application prospects in underground metal mine. Therefore, the results show that it is an ideal way to change the present structure of cooling and heating source in metal mine.Introduction In recent years, overuse of fossil fuels has posed a grave threat onto the environment, which makes renewable energy a more important status in energy structure. Development and utilization of renewable energy has become an important direction. Water source heat pump technology is to use solar energy stored in water as cold/heat source to convert energy. Currently, this technology has been widely used in some advanced countries. However, due to facers of implementation technology and component costs, there is still a gap in water source heat pump technology between China and these advanced countries. According to (Blum et al 2011) that after in-depth study, water source heat pump technology has developed rapidly in China recently, and the gap is gradually reduced. Groundwater source heat pump system as a kind of high efficiency, energy-saving and environmentally friendly technology in recent years, more and more get the people's attention. At the same time, its practical application has also been rapid development. Based on (Ni et al 2015) that According to the relevant departments of the prediction, the technology will become the 21st century the most efficient heating and cooling technology."

Jan 1, 2017