Search Documents

By N. Djordjevic

The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice - not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape.

Jan 1, 1997

By R. L. Garrett

The quality of mineral additives used in a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally wed minerals are bentonite, barite, barite/hematite blends, and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity and gel strength and to provide a low permeability filter cake. A multimillion dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason oil companies using these materials sometimes set their own quality standards beyond those already specified in APZ Spec. 13A. Also discussed in this paper are the current standardization activities of API Committee 13 on these minerals.

Jan 1, 1988

By Marvin Barnes

The Sacaton mine is a relatively new open¬pit copper mine owned by Asarco, Inc., which has been in production only a few years. The mineral deposits consist of two ore zones; a western, near-surface zone minable by open-pit methods, and a deeper eastern zone which will have to be mined underground, probably by block caving. The copper deposits are related to small quartz monzonite intrusives implaced into Precambrian granites. Both rock types act as hosts for the copper mineralization, which has been secondarily enriched sufficiently to constitute ore. In the western zone the enriched supergene chalcocite has been subjected to postenrichment oxidation processes with partial destruction of the chalcocite blanket. The deeper eastern chalcocite zone has not been as severely affected by later supergene processes. Several mineralogical populations are represented in the total copper deposit. Leached capping overlies the chalcocite enriched zone, and in the western ore body there is a very irregular interface between the leached and enriched zone, which is complicated by oxide copper minerals irregularly distributed. Primary lower-grade chalcopyrite mineralization occurs below the enriched zone. When mining commenced near the top of the enriched zone, considerable difficulty was encountered in correlating the actual grade of ore in place with the estimated grade of the mining blocks. The mineralogical complexity and fairly wide spacing of diamond drilling made reliable grade estimation of individual ore blocks a difficult procedure.

Jan 1, 1979

By F. M. Doyle, S. Duyvesteyn, K. Sreenivasarao

Toxic metals entering surface or ground water from sources such as metal finishing shop spills and abandoned mines can pose a significant threat to public health and the environment. Ion flotation and similar foam separation techniques show great promise for treating dilute, metal-contaminated solutions, and could also be used to treat effluents from many minerals and metallurgical processing operations prior to discharge. In ion flotation, an appropriate collector is added to the solution to form hydrophobic complexes with the metal ions. These metal-bearing species are then removed by flotation, usually with trace addition of a frother to stabilize the foam. In an effort to better understand the underlying scientific and engineering principles that determine the performance of ion flotation, the removal of Cu(II), Pb(II), Cd(II), Cr(II) and Cr(VI) has been studied using laboratory scale flotation columns in batch mode. The effects of the superficial air velocity, solution and froth height, nature of the collector, collector: metal-ion ratio, ionic strength and several frothers at low concentrations on the flotation kinetics are reported. Finally, results are presented on methods that might allow regeneration of collector and recovery of by-product metal from the foam product.

Jan 1, 1995

By David J. Brown, Richard C. Fountain, Marc V. Hurst

The Central Florida Phosphate District, one of the most productive phosphate districts in the world, has been mined principally within Polk and Hillsborough Counties, Florida. Recent development is extending the district southward into Hardee, Manatee, and DeSoto Counties. This area is known as the Southern Extension. The combined area of these two phosphate-bearing areas encompasses about 2,000 square miles. Structurally, the district and its Southern Extension lie at the southern end of the Ocala Arch and are flanked by the Hillsborough High to the northwest. South of this area is the South Florida Embayment. The Osceola Low lies to the east. The phosphorite within the Central Florida Phosphate District generally dips very gently (<0.1°) to the south. The boundaries of the central Florida Phosphate District are generally defined by thinning of the phosphorite due the adjacent structurally high areas to the north, west, and east, and by increased clay, CaO, and MgO content reflecting lithologic differences to the east and south. The Bone Valley Member of the Peace River Formation and reworked sediments of more recent age were the primary ore-bearing horizon in the Polk-Hillsborough County area. As those reserves are depleted, the less desirable phosphorites of the Peace River Formation are being exploited in the Southern Extension.

Jan 1, 1993

By R. Venugopal, T. C. Rao, M. Vanangamudi

Introduction The kinetic approach, to understand a process in detail, has been extensively used in the unit operations of many engineering systems. In green pelletization, the kinetic studies have been mainly oriented towards quantifying the growth mechanism (Kapur and Fuerstenau, 1964; Sastry and Fuerstenau, 1977; Capes and Danckwerts, 1965; Kapur and Fuerstenau, 1966; Kapur, 1972) and in a few cases, relating the rate of growth with added liquid content (Kapur and Fuerstenau, 1964; Newitt and Conway-Jones, 1958). Studies on the kinetics of green pelletization, in terms of the order of the kinetics are virtually non-existent. Sastry and Fuerstenau (1970) classified the agglomeration process into "free in-space" (dilute particle system) and "restricted-in¬space" (highly dispersed particle system) and noted that the former is a second-order process while the latter corresponds to a pseudo first-order rate process. The present paper attempts to describe the kinetics of green pelletization, in terms of order of the kinetics, using pyritiferrous shale as the material system. Experimental Pelletization experiments were carried out using -100 mesh pyritiferrous shale, in a laboratory disc pelletizer, at four intervals of pelletization time (15, 20, 25 and 30 min). The green pellets obtained were size analyzed. The size distribution of pellets has generally been represented by a single parameter such as the mean granule diameter, ratio of maximum and minimum pellet diameter, etc. In the present study, the d50 (50% passing size) of pellets has been considered to represent the size distribution of pellet. Kinetic equations The process of size enlargement is considered analogous to chemical reaction and a general kinetic equation of nth order for growth of pellets is given as

Jan 1, 1990

By D. S. Choi, D. L. McCain

INTRODUCTION Coal is forecast to be an increasingly important and economical source of energy for the future as the supply of oil and gas declines relative to overall energy demand and perhaps in absolute quantities produced. With the decline in productivity, especially in underground mining, in the early seventies coinciding with the need to produce greater quantities of coal for market, a gradual change from room-and-pillar mining to longwall mining has been taking place in the United States. Consolidation Coal Company (Consul) produces about 50 million tons of coal per year with approximately 66% being from underground mines. Most of the mines are located in the Appalachian Region in the States of Pennsylvania, West Virginia and Virginia, and in Ohio and Illinois. Coal is produced by the room-and-pillar mining method with continuous mining machines in addition to an increasing number of longwall mining faces. Continuous mining machines will continue to be used for driving longwall development entries as well as in areas where partial extraction must be practiced in order to support the overburden rock because of surface structures or in areas that cannot be subsided, or where unfavorable geologic conditions limit the application of the longwall mining methods. ROOM-AND-PILLAR MINING METHOD Some background in the room-and-pillar mining method may be helpful to provide perspective. This method has been widely practiced since the beginning of coal mining in the region. It is a flexible system because it can provide either partial or nearly complete extraction, and coal pillars can be left where needed to support surface structures or oil or gas wells or because of unfavorable geologic conditions (Choi, Dahl and McCain, 1980).

Jan 1, 1983

By John C. Schneider

During the past decade, operators and researchers have worked toward a better understanding of the mechanisms operating in flotation. As reported by W. J. Trahar in 1981, this work commenced with the operators determining a relationship between recovery and particle size. They defined three particle size ranges, that being fine, intermediate and coarse. It was noted that the fine and the coarse ranges had slower flotation rates than the intermediate range as demonstrated by their lower recoveries.

Jan 1, 1998

By D. M. Sloan

While surety capacity for the mining industry continues to shrink, States are demanding greater financial certainty for closure/post closure obligations. To combat these demands, larger mining companies are pursuing a Mining Surety Reinsurance Program that requires a significant up front capital contribution. This paper outlines an alter-native program for middle market mining organizations. The program utilizes a “Blended Finite Risk” environmental insurance solution with surety acting as the “front” in states where insurance is not an acceptable form of collateral. Marsh proposes creating separate programs for each State requiring surety. The reason for separate programs stems from each states’ different surety rules. Insurance companies typically require at least $5 million in future value remediation liabilities for finite risk programs. Since most middle market mining companies have obligations that fall below this threshold, the Blended Finite Risk Program contemplates combining several companies closure/post closure liabilities to accomplish the minimum amount required by the insurance company. Why use a Blended Finite Risk Program? One of the primary benefits is the financial assurance that funds will be available for planned remediation. For example, the financial assurance may be required by a government agency. The certainty may help facilitate a merger or acquisition. Additionally, the funds may be part of a CER-CLA PRP settlement. In all cases, the insurer providing coverage would be a secure independent 3rd party. A Blended Finite Risk Program also provides a long-term solution – up to 30 years and in some select cases longer. The benefit to a state or the BLM is the removal of financial uncertainty. An insurance company writing the policy would have an AA or AAA balance sheet. The hardening of surety markets coupled with the tightening of financial assurance requirements in many states have necessitated the posting of 100% collateral. This program substantially reduces these collateral requirements.

Jan 1, 2004

By Samuel Frimpong

In this paper, the authors present a typical mine profitability model. The method of generating system moments is used to examine the sensitivity of the profitability function to changes in the dependent variables, and to express the expected risk associated with undertaking the project in a predicted economic and technical environment. Profitability of a mining venture is a function of many variables ore grade, capital and operating costs, milling efficiency, ore reserve tonnage and annual tonnage, equity - loan structure, tax regime, etc. Estimates of the expected value and the variance of the profitability function are obtained by calculating the partial derivatives of the function with respect to the dependent variables, using the Taylor series expansion method to the second order. Sensitivity analysis is carried out by examining the effects of each variable on the profitability function, which is determined by the magnitude of the product of its partial derivative and variance. An appropriate probability density function, based on the expected value and the variance of the profitability function, is assumed to estimate the expected risk associated with the project. This expected risk is a measure of the area under the profitability density function below the appropriate, selected discount rate or the cut-off net present value (NPV). The results are compared with those obtained by using the Monte Carlo simulation technique, and they show that either of the two methods could be used to evaluate the probability of project failure or success with no significant difference.

Jan 1, 1992

By A. Peppas

Perlite is a naturally occurring siliceous rock, which can be expanded from four to twenty times its original volume when heated at a temperature close to its softening point. The expanded perlite is characterized by increased sound and thermal insulating properties. However, the conventionally expanded perlite products have high porosity and low mechanical properties that limit the range of their applications in the construction and chemical industry. The present work aims at the development of new closed porous microcellular material from perlite with enhanced mechanical and physical properties to be applied in new applications, like joint compounds, functional fillers for special paint types, special blasters and mortars, artificial marble. For the production of these new materials a vertical electrically heated furnace with six different heating zones and controlled gradient temperature profile was used. The effect of major process parameters, like temperature and air flow, on the quality of the produced materials was studied using Greek perlite from Milos Island. The quality of the new products was evaluated in terms of their bulk density, compression strength, water and oil absorption, surface area and pore volume. The experimental results show that the produced materials are characterised by improved mechanical and physical properties compared to the conventionally expanded perlite products.

Jan 1, 2006

By G. Schmelzer

The disposal and reintroduction into recycling of residues produced by today&apos;s industrial society is not only a problem of much public debate in the countries concerned but also an increasingly prominent topic in science and research. In the treatment of most types of waste, ecological as well as economic considerations are important factors. In view of this, not only will future expenditures for treatment and processing become more significant but also, on the other hand, the savings and profits resulting from recycling. The situation described above reflects the inherent problems in the treatment of solid residues produced by waste incineration plants. The incineration of municipal waste produced approx. 2.7 - 2.8 million tonnes of solid residues in 1993 in the Federal Republic of Germany, which in part included still considerable amounts of organic and inorganic pollutants that could potentially be released into the environment. The most significant of these in terms of volume is incinerator ash at approx. 2.4 million tonnes. Through the use of innovative processing techniques, attempts are being made to convert the residues into a form that remains environmentally neutral over the longest period of time possible. One such group of techniques includes smelting technologies. After it has undergone specialised treatment, mineral incinerator ash is converted into environmentally neutral and reusable glass (vitrification) since, besides a reduction in the volume of the residues by approx. 90%, the main goal is a complete immobilisation and destruction of inorganic and organic pollutants respectively. These glasses, after they have been reshaped, are resold as commercial products such as damming or form glass.

Jan 1, 1995

By Etienne Simode

When a fire breaks out in a mine access road, the hot smoke, due to heat transfer with the surrounding strata, progressively cools as it moves forward. Depending upon the resulting temperature distribution, the density of the fluid changes. This change will bring about: Firstly, a variation in the resistance of the roads, a static factor which will affect ventilation flow rates; Secondly, the appearance of extensive aerodynamic driving loads in the vertical and angled roads, a dynamic factor which can have an extensive impact on ventilation. Because of the appearance of combustion and distillation products, the vaporization of water, which wets the timbering and strata, and the expansion of gases, fluid rates can at times be increased tenfold in the area of the fire. These disturbances may cause explosions and ventilation inversions, which fill other working areas with smoke toxic to workers, and which can come up upon rescue teams from behind. Due to the progressive heating of the surrounding rocks, which will slow down heat transfer, these dangerous conditions change over time. At the Lorraine Basin Coal Mines, programs have been set up and employed for the computer simulation of these phenomena over time. They serve to anticipate or to understand such phenomena, the input data being the characteristic parameters of the mine ventilation network, the operating curve of the main fans, and measurements or estimates of some temperatures. Two programs, employed together, have been developed for these studies: One program, called RESO, calculates the distribution of flow rates and pressures throughout the entire network; The other, called FEUMIN, determines smoke temperatures over their entire path.

Jan 1, 1980

By Gerrit V. R. Goodman, Fred N. Kissell

The issue of miner safety in case of an underground mine fire has been extensively examined by both government and industry. These efforts have intensified in recent years following a number of fatal fires at underground coal mines. As a result, there is an increasing interest in the reliability of coal mine escapeways during a mine fire. This paper discusses the use of fault tree analysis for evaluating escapeway reliability. A fault tree is developed using standard logic formulations. It is later evaluated using commercially available software. The computer model uses Boolean reduction to obtain the minimal cut sets and minimal path sets of the tree. A brief analysis is also conducted to determine the occurrence probability of the TOP event. This study shows that fault tree analysis is a viable means of analyzing escapeway reliability. The cut and path sets reveal those event sequences leading to fatalities. Such information is useful in safety training and accident prevention. The probability of the TOP event shows the frequency of occurrence for fatalities in an underground mine fire. The usefulness of this value, however, is limited by the accuracy of the data for the initiating events. For mining events, the data is difficult to estimate precisely.

Jan 1, 1989

By Todor P. Stefanov

The thermal draught within ventilation networks of underground mines depends to a great extent on the shafts depths and degree of change of ventilating air density. When the topology and space orientation of a ventilation network are constant, the dynamics of thermal draught is determined mainly by the variations of the heat- and mass-transfer processes in the openings. This conclusion follows from the well known basic theoretical notions about the thermal draught-aerostatics and thermodynamics [1]. Quantitative evaluation about the influence of heat- and mass-transfer processes on dynamics of thermal draught could be made through: direct mine measurements, special experiments and with the aid of mathematical models. The first two methods produce sufficiently accurative results, however it is very difficult to perform such studies, particularly when these processes are evaluated within a large scope and multifactor aspects. Mathematical models of thermal draught allow to overcome easily these difficulties. The degree of accuracy of results, obtained by this method, depends to a great extent on the degree of approximation achieved by the model to the real heat- and mass-transfer processes. In this paper, with the aid of Bulgarian developed method, algorithm and computer program V WT-4 - for complex evaluation of ventilation parameters in active mine ventilation networks [2], the authors investigate some changes in the thermal draught. Basically, the method is an iterating evaluation of an open set of equations, which represents relationships between the following basic parameters of a mine ventilation network: [ ]

Jan 1, 1980

By Giovanni Toniatti

Brazil is a country with continental dimensions. It hosts many different varieties of terranes and geological environments in its 8.5 million km2 (3.28 million sq miles). This mineral endowment has been important for the country&apos;s economic and social development process since the early colonial period, leaving Brazil with a legacy of almost 400 years of mining tradition. Mining in Brazil started in the early 17th century with diamond and gold discoveries. The made the country the leading producer of both for more than a century. This phase faded by the late 18th century when the alluvial deposits were depleted. It finally yielded to competing countries where technology and capital were being applied more efficiently. This period of mining dormancy lasted from the late 19th century until the first decades of the 20th century when Brazilian mining picked up. There was growing pressure on mineral resources by the affluence of the industrial society. The fast-growing demand resulting from the two world wars had brought the Brazilian mineral wealth back to the scene. This second Brazilian mineral boom made the country a leading producer of iron and manganese ore, quartz crystals and other strategic minerals. This expansion in Brazil&apos;s mining industry provided the basis for the country&apos;s industrialization process. This was led by the Brazilian steel and petroleum industries. Unfortunately, the thrust provided by this modern industrial basis was not properly used as a lever for further industrial development. The upstream industrialization process was not supported by the proper development of the raw materials supplying basis. The resulting industrial model was heavily dependent on imports of raw materials. It did not support the economic growth and faced fierce industrial competitiveness and sophistication that emerged with the postwar economic boom.

Jan 1, 1997

By I. Ehie, Y. P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15% to a maximum depth of 46 m (150 ft). Pit orientations along the true dip (dipline), along the strike (strikeline), and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas and also to furnish data for the computer simulation models. A dragline microsimulation, a shovel/truck simulation, and a surface mine cost analysis models were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and seam pitch. The productivity (m3/h) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity. Larger size trucks were preferable to smaller size trucks in the pit con¬figuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip for the mining condition studied.

Jan 1, 1987

By Winfield G. Wright, Greg P. Meeker, Philip L. Verplanck, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

A really extensive acid sulfate-altered and mineralized rock in the southeast Red Mountains area is noted for its association with naturally occurring and mine-related acidic and metal-rich waters. Integrated geologic and aqueous geochemical studies demonstrate that the degree of metal mobilization and acid production in natural waters correlates well with the type of hydrothermally altered rock and structural features in which these water interact. Quartz-sericite-pyrite, quartz-alunite, and argillic alteration assemblages are associated with some of the most naturally acidic, high-metal waters in the study area; calcite-bearing propylitic rocks are related to the most pristine waters and buffer sulfate-rich, acidic waters produced by pyrite oxidation. Trace metals in natural waters are mostly derived from enargite, zinc-rich tetrahedrite and sphalerite. Pyrite oxidation contributes very little with respect to base-metals in these natural waters.

Jan 1, 2000

By M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya, K. You

The friction factor is one of the more difficult parameters to determine in ventilation planning. In practice, this can be estimated from published factors such as those of McElroy. The problem with this approach is that the selection requires some judgement, and the estimated values offer no more than guideline accuracy. This study, examines the effects of four factors on the coefficient of friction for a simulated mine airway. The factors are: airway cross-section, asperity height, flow direction, and cross-cut spacing. The study includes the modeling of a mine airway and the evaluation of the results from 13 experiments on flows of air over rough surfaces. The model, physically represented by a wind tunnel, includes a rough surface section which can be modified to simulate mine airways of various shape and asperity height. Most of the experiments were performed under controlled flow conditions during which the Reynolds number was varied between 50,000 and 300,0000. Based on this study, the friction factor for a mine opening was found to depend not only on the size and shape of the surface asperities but is also affected by the orientation of them in relation to the flow direction.

Jan 1, 1991

By P. Mousset-Jones, G. Danko

Rock thermophysical properties, i.e. heat conductivity and thermal diffusivity, were obtained for reference values at the Waldo Test Mine for mine fire simulation purposes. An in situ measurement method was chosen since it could include the effect of rock fractures. The REKA method (Rapid Evaluation of k and alpha) was used because it can measure conductivity (k) and diffusivity (alpha) simultaneously within an eight-hour measurement period. A total of six measurements were taken in three different holes, and at two different depths from the collar of the hole. Each measurement provided an averaged conductivity and diffusivity for a volume of rock of approximately one cubic meter. The boreholes were driven into the upper and lower limestone, two at right angles to and one parallel to, the stratification of the rock. Significant representative conductivity and diffusivity values were obtained for the whole mine by averaging the six measurement results. The thermal properties for the band of shale in between the two limestones were not measured in situ, but only in the laboratory. Problems were encountered in the evaluation because of unexpected heat conduction on one side of the symmetrically built probe. A modification was made to the previously developed evaluation method together with further testing and correction, before the final results were obtained. As expected, the in situ and lab- oratory measured values of k and alpha compared favorably, since the in situ rock was dry and relatively unstressed.

Jan 1, 1989