Search Documents

By Earl G. Hoover, V. S. Znamensky

For most geologists and miners the term asbestos refers to a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven; these fibers are heat resistant and chemically inert, and possess a high electric insulation and therefore are suitable for uses where incombustible, nonconductive or chemically resistant material is required. The US Mining Safety and Health Administration (MSHA) specifically refers to the naturally occurring minerals chrysotile, amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos as asbestos if the individual crystal fragments have the following dimensions: length-greater than 5 µm; maximum diameter-less than 5 µm; and a length to diameter ratio of 3 or greater. Since asbestos has been identified as one of the ten most carcinogenic substances (a cancer-causing agent), it has become, for many government regulatory agencies, a major issue concerning banning emissions to the environment. Very few recent issues have caused as much concern for the crushed stone industry as asbestos. Complicating the problem is the fact that several federal and state bureaus have greatly compounded the confusion because each has become involved in the asbestos dilemma. Simple solutions to a very complex problem have been proposed by these various governmental groups. In addition to governmental bungling is the fact that public interest groups have been able to use federal and state laws that have been enacted with a strong environmental bias to foment even greater complexities. Such is now the state of the asbestos problem. No con- firmed health risk has been associated with low-level exposure, namely crushed stone in an unbound form; a methodology for sampling and analyzing for asbestos has not been developed; a precise definition of what is asbestos does not exist, nor does a concensus among the various government groups as to what course of action to pursue. Pure asbestos as it is mined for commercial purposes does not exist in the properties mined by the crushed stone industry. Where the six asbestiform minerals do appear (to date we've been referring mainly to chrysotile in serpentinite formations in Maryland) the amount of the asbestiform mineral present is generally quite small. They generally appear in scattered, miniscule amounts. In the case of Rockville Crushed Stone in Montgomery county, Mary- land, the chrysotile is less than 1/2 of 1% of the rock deposit. No health risk has been identified with such minute quantities of asbestos minerals. MSHA standards for the occupational health and safety of quarry workers are being met; and there is every indication that normal background levels of asbestos, throughout the surrounding countryside, are as high or higher than levels measured on roads where the rock is used in pavement or base. The problem and the controversy lie with improper terminology on the part of so-called public interest environmental groups, aided and abetted by some governmental agencies who, to be charitable, we can best describe as uninformed. The news media frequently has fanned the issue, unintentionally we'd like to think, by quoting these misinformed authorities and not bothering to question the facts or adequately report balancing information handed to them. It is much better copy to talk about an asbestos cancer scare, than to deal with rather mundane measurements and descriptions that are hard to understand. At the heart of the issue is the improper use of the word asbestos. Instead of being confined to the geological description of the six asbestiform minerals-chrysotile, amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos-the word asbestos is also wrongly used, but too-frequently to identify many other minerals that happen to have elon-

Jan 1, 1986

By Warfield Garson

Few, if any, of the non-ionizing radiation health hazards to be found in either surface or underground coal mining are uniquely different because of their being found in the work environment. Hence, they can be considered generally for their bio-effects on the worker when found in the mining work environment. The same may not be said, however, for the lack of non-ionizing radiation and its bio-effects, particularly as it relates to underground coal mining. The term "non-ionizing radiation" refers to various forms of electromagnetic radiation of wavelengths longer than those of ionizing radiation. As the wavelength gets longer the energy of electromagnetic radiation decreases. Therefore, all non-ionizing forms of radiation have less energy than cosmic, gamma, and X-radiation. In order of increasing wavelength, non-ionizing radiation includes ultraviolet, visible light, infrared, microwave, and radiofrequency radiations. The energy frequency and wavelength range of both the ionizing and non-ionizing electromagnetic forces are shown in Table I. To convert the wavelengths of various radiations to Ångström units, one multiplies millimicrons by ten. In a vacuum, all electromagnetic radiation has the same velocity, namely 3 x 1010 centimeters per second. The natural source of radiant energy here on earth is our sun which emits radiation continuously over a wide spectrum. This radiation on average reaching earth ranges from 290 nm in the ultraviolet range to over 2,000 nm in the infrared range with a maximum intensity of about 480 nm in the visual range. You will note this falls into the visible blue wavelength and accounts for our blue sky and blue ocean and deep water effects. We are all familiar with the fact that the passage of solar radiation through the atmosphere to the earth changes the spectrum considerably because the atmosphere absorbs and scatters many of the sun's rays. The ozone in the upper atmosphere absorbs the shorter ultraviolet wavelengths and water vapor absorbs some of the infrared wavelengths. Smoke, dust particles, gas molecules and water droplets scatter the rays, especially those of shorter wavelengths. In addition to the sun, every gas, liquid or solid object at a temperature above absolute 0° radiates energy. Solid objects emit almost continuous spectra. At low temperatures only radiation of the longer wavelengths in the infrared range is emitted, but as the temperature of the object is increased, more and more of the shorter wavelengths are added. This fact is most readily demonstrated by heating a piece of steel. When a piece of steel reaches a temperature of about 1,700° Fahrenheit, it gives off radiation at the red end of the visible spectrum and appears dull red. As the temperature is further increased, the shorter rays are also emitted, until at about 2,100°F, the metal appears white, due to the emission of wavelengths throughout the entire visible range. Gasses, on the other hand, when heated emit radiant energy only at certain wavelengths, which are characteristic of their chemical structure. This latter fact is of importance in underground coal mining as high intensity gas and vapor lamps are becoming more and more utilized for illumination in underground coal mining. The biologic effect of non-ionizing radiation exposure depends upon the type and duration of exposure and on the amount of absorption by the miner. The effects of this radiant energy on the miner fall into four distinct types: (1) the heating effect of infrared radiation, (2) the effect on the eye of visible radiation, (3) the effects of ultraviolet radiation, and (4) the growing potential effects of the misuse of microwave radiation. Each non-ionizing type of radiation will be considered individually. ULTRAVIOLET RADIATION The sun is the major source of ultraviolet radiation, which is of concern in open pit and surface mining at certain seasons and in certain climes necessitating protection for the surface miners under those conditions; nonetheless, there are some man-made sources such as electric arc lights, welding arcs, plasma jets, and special ultraviolet bulbs for illumination underground that demand surveillance in the underground environment to be aware of whether the miners are at risk above the threshold limit values allowable. Since ultraviolet radiation has little penetrating power, the organs that are affected are the skin and the eyes. Ultraviolet radiation is strongly absorbed by nucleic acids and proteins, and the effects in man are largely chemical rather than thermal. Short-term effects on miners include acute changes in the skin. These are of four types: (a) darkening of pigment, (b) erythema (sunburn), (c) increase in pigmentation (tanning) and (d) changes in cell growth. Ultraviolet radiation also causes acute effects on the tissues of the eye. Overexposure can lead to keratitis, inflammation of the cornea, and conjunctivitis. Long-term effects of ultraviolet exposure include an increase in the rate of ageing of the skin with degeneration of skin tissue and a decrease in elasticity. Late effects of ultraviolet on the eye include the development of cataracts. The most serious chronic effect of ultraviolet exposure is skin cancer. Ultraviolet radiation effects are increased by some industrial materials and drugs. After exposure to such compounds as cresols, the skin is exceptionally sensitive to ultraviolet radiation. Photosensitivity reactions occur after exposure to a variety of other chemicals and drugs including dyes, phenothiazines, sulfonamides, and sulfanylureas. On the other hand, we must remember that ultraviolet radiation has an important role in the prevention of rickets. Vitamin D is produced by the action of

Jan 1, 1981

By Joel K. Waterland

GENERAL DESCRIPTION Open cut-and-fill stoping for many years was prob¬ably the most widely used mining method in under¬ground metal mines. Then for a time this method was largely supplanted by the blasthole stope. It again be¬came popular as many mines reached depths or grades where methods requiring large open voids to remain open for extended periods of time became unsuccessful, often as a result of excessive dilution. The open cut-and-fill method is very flexible and is readily adaptable to almost any ore body. The standard application requires that a slice of ore usually 2.4 to 3 m (8 to 10 ft) thick be removed from the back of the stope, and as the ore is taken down, the back is dressed and rockbolted. After the back is secured, the broken rock is removed through rock passes to the level below. When the rock has been removed, the rock passes are extended upward the height of the ore removed, the stope is backfilled, and another cycle is mined. This method is best employed in plunging ore bod¬ies with considerable vertical extent, ore areas that re¬quire selective mining, ore areas where weak wall con¬ditions exist, and ore bodies that have an ore value that will carry this relatively expensive mining method. Blast¬hole stoping, shrinkage stoping, and other mining meth¬ods that do not employ rock passes in a stope are not efficient in plunging or flatly dipping ore bodies because the footwall makes ore removal quite difficult. Since mining is accomplished by taking down slices of the back, only small areas of the wall rock are exposed at any one time, and these only for short periods. Due to limited back height, areas of uneconomic rock may be left in place, or they may be mined and the material gobbed in the stope. Because the miners in the stope must work under freshly blasted areas, the amount of ground control is usually great. The volume of rock that is broken during one section of mining is relatively small and the amount of nonproductive work required is high. This results in limited productivity for the scope and, be¬cause of the nonproductive work that must be done on a regular basis, the production from the stope may be quite cyclical. SUITABLE ORE BODIES The open cut-and-fill method may be adapted to al¬most any type of ore body with a relatively high vertical extent. The ore body must be accessible at both top and bottom as well as at regular intervals throughout its vertical extent. Although adaptable to most ore bodies, the method is probably best employed where the ore has poor con¬tinuity and where most types of bulk mining would pro¬duce excessive dilution. In areas of poor ore continuity, the capability of continuous and extensive sampling dur¬ing the mining of each cycle makes this method very desirable. This capability also minimizes the amount of evaluation sampling that must be done before mining is started. Because of the extractive system used, the size and shape of the stope may be as readily changed as the sampling mandates. Probably the only ore characteristic demanded is that the ore has strength enough to be sup¬ported through the use of rockbolts or cable bolts dur¬ing the mining and backfilling cycles. Good planning, systematic sampling, and careful supervision will pro¬duce a product with less dilution than any other open stoping method. PLANNING Evaluation Planning Once it has been decided that the open cut-and-fill method would be the most efficient for mining a par¬ticular ore body, the next considerations would probably be the availability of an economical backfill material and the selection of an efficient transport system for this material. Although hydraulically transported mill tail¬ings are the most widely used product, this is not always practical due to mill location or the quality of the tailings. In such cases, backfilling may be used. The type of backfill and the type of equipment used will determine if a floor or capping on the backfill is required to minimize dilution during ore removal. The early selection of rock removal equipment is im¬portant since equipment usually determines the amount of development work required to bring a stope into pro¬duction and the size of the openings needed. The size and continuity of the ore body will usually determine the type of loading equipment. The use of slushers or load¬haul-dump (LHD) equipment captive in the stopes will minimize the amount of development. If the ore con¬tinuity is such that a ramp system for extraction can be used, the cost of development will be increased but the flexibility of continuous mining will minimize the cycli¬cal nature of the production. The height of the mining section usually is deter¬mined by the strength of the wall rock and the amount of back bolting required. Once this has been decided, the appropriate drilling equipment can be chosen. The number and sizes of the rock passes employed depends upon the type and size of the extractive equipment and the type of backfill that is to be used. Since the miners must enter and leave the stope each shift, the level inter¬val is usually maintained at approximately 45 m (150 ft). Access from the level above into the stope must be main¬tained at all times. The employees perform all the work in the stope and adequate ventilation must be provided. Stope Planning Due to the flexibility of the method and the vari¬ability of the ore zones, layout is usually done on a stope basis. In areas where continuity is a problem, the size of the stope is usually determined by the boundary of the ore (with all of the ore within that boundary being removed). In areas of good continuity where ramps are to be used, the length of the stope may be determined by the length of time each of the cycles (preparation, back¬fill, mining, and ore extraction) requires. The ramp work is then laid out so that access to the various parts

Jan 1, 1982

By W. R. Junge

The investigation, selection, and implementation of remedial activities for large, complex mining and milling sites is dependent on the cost-effective management of tailing and waste materials. Site investigations evaluate the contaminant source areas, assess the potential release rate of contaminants, and determine the acceptable contaminant release rate for the site. Selection of appropriate remedial activities is based on evaluation of constructability, reliability, performance, effectiveness, permanence and cost. Remedial technologies available for tailing and waste material include removal, consolidation, capping and drainage control. Proper implementation and documentation of the selected remedial activities are critical to the overall success or failure of the remedial program. A step-by-step process, established at the initiation of a project, should accurately document all construction activities, monitor environmental conditions at the site, assess the performance of the remedial activities, and, ultimately certify that the remedial activities have met relevant and appropriate standards. Case histories are presented for a uranium mill at Uravan, Colorado and a lead, zinc mine at Gilman, Colorado. These case histories provide examples as to the combination of remedial technologies that have been applied at these specific sites.

Jan 1, 1989

By D. Butler

Lateral density changes in the subsurface cause a change in the vertical pull of gravity at the surface. By very accurate measurement of gravity and the practical application of common sense, a microgravity survey can sometimes detect natural or man-made voids, bedrock profiles, and geologic structures of engineering interest. This paper will give some practical guidelines for the application of microgravity surveying. Emphasis in many papers (Blizkovsky, 1979, Fajklewicz, 1983) has been on the anomaly size: herein emphasis will be placed on detectability and signal-to-noise ratios. First, some easy to use curves for anomaly valuation are adapted from Arzi (1974). Secondly, the predictable noise sources are discussed. Thirdly, representative models of abandoned underground workings are evaluated for microgravity surveying given the probable noise in the survey results.

Jan 1, 1988

By R. E. Greuer

The design of mine fire emergency plans requires that the contamination of mines by fumes, and the mutual interaction of fires and ventilation systems be pre-calculated. Several computer models were developed by the Bureau of Mines for this purpose during the last decade. The models advanced in sophistication from the transient-state simulation of fume concentrations for the early stages of a fire to the steady-state simulation of airflow rates, concentrations, and temperatures for fully developed fires, and finally to the complete transient-state simulation of fires and ventilation systems. The principal features of these models are described.

Jan 1, 1989

By R. R. Klimpel

During the period of 1973-79, an extensive period of research and development was undertaken by Klimpel and coworkers (1980, 1981, 1982a, 1982b, 1983. 1984, 1987) on the identification of a commercially viable chemically assisted approach to improving the efficiency of the wet grinding of coals and ores in tumbling media mills. The emphasis of the previous publications just listed was on the engineering use implications of controlling-slurry viscosity (rheology) in laboratory and plant scale grinding devices. In this paper, some discussion and results pertaining to the actual chemical screening phase will be presented.

Jan 1, 1988

By R. R. Graham

Echo Bay Minerals operates a 650 tpd gravity float gold circuit at their Manhattan facility. The objective of this paper was to document the gold recovery by size distribution. This was accomplished by studying the material balance of each size fraction as it progressed through each gravity Circuit separator. It proved to be an impossible task. Figure I depicts the gravity circuit. The gravity cyclone underflow goes to two duplex Pan American type jigs. The jig overflow reports to the OK Flash Float Cell. The cyclone hutch product is reground and goes to a full size wilfly table. The rougher table concentrate reports to a pilot size Wi1fly cleaner table. The cleaner and rougher table tails circulate back to the jig feed. The gravity circuit was composite sampled for two to four hours per day for four days. Each sample was taken every 20 minutes. Each composite sample was filtered, dried, repu1ped, and screened through a wet/dry screening procedure. Each size fraction was checked for gold value by fire assay fussion technique. A material balance was run on each size fraction. The tables listing the results are enclosed.

Jan 1, 1989

By Nader Shahcheraghi, Verya Nasri, Mehdi Bakhshi, Ali Haghighat

An accidental fire load is one of the major loads considered in design of segmental linings in transit tunnel. Typically, a two-dimensional coupled thermo-mechanical finite element analysis (FEA) is conducted. The conventional approach involves using standard fire curves (temperature-time curves) which can lead to a significant overestimation of fire load and tunnel lining thickness in metro tunnels. The focus of this paper is on the cutting-edge approach, using 3D computational fluid dynamics (CFD) analysis of real train fires in metro tunnels and coupled thermo-mechanical finite element analysis (FEA) to accurately and cost-effectively design fiber-reinforced concrete (FRC) segmental tunnel linings for large-scale metro projects.

Jun 23, 2024

By M. J. Blattman

The problem of measuring the amount of rock removed during a given time interval is faced by most milling operations. Many methods have been developed with varying degrees of success, dependent upon the mining method and the availability of usable data. The Rosebud Mine has been in production for nearly two years, employing several techniques to estimate monthly production from underground production stopes. The use of three-dimensional solids generated from survey data has greatly improved the reliability and confidence of monthly production reports. The authors will summarize the methodology currently being utilized at Rosebud.

Jan 1, 1999

By T. Hayes

Track-type tractors remain one of the most cost-efficient stripping tools available to coal miners. Whether they are "sweetening up" a dragline operation with pre-benching or serving as the primary stripping tool, dozers can play an important role in driving down mining costs. This paper reviews the application zone of track-type tractors. In addition, it provides tips on site set-up, equipping of tractors, and machine operation which the audience can take home and apply.

Jan 1, 1996

By L. M. English

When plotted as head vs. volume, fan curves start high and decrease in head with increasing volume while mine head curves start low and rise with increasing volume. Their intersection is the system operating point But wait a minute: Isn't head loss a negative number, a debit? And isn't fan head an energy addition, a credit? This, as every ventilation instructor knows, is often a stumbling block to student or audience comprehension. It is possible to use the intuitively correct curves -pressure losses as negative values and energy additions as positive values -and still obtain the correct operating point: adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at \\tIich the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure; with the standard approach it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel circuit or ventilation net\wrk. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1997

By F. W. Brackebusch

Paste is a high density mixture of water and fine solid particles with a relatively low water content (10-25%) such that the mixture has a consistency as measured by the ASTM slump cone test from slightly greater than zero up to nearly 12 inches (305mm). Particles of different size classes will not segregate or settle when the paste is not being agitated or when it is stationary in a pipeline. Cement may be a component of paste. Larger particles of aggregate can generally be added to a paste without greatly changing the pipeline transport characteristics. A paste may bleed water slightly when it is allowed to be motionless for periods of up to several hours, but the solids do not become so dense that the paste cannot be easily re-fluidized. The dividing line between the definition of a high density slurry and a paste is not sharp. It is a practical matter that must be considered when designing a pipeline transportation system. If the pipeline is very short, there is very little risk of plugging the pipeline with a high density slurry when flow is stopped for short time periods. With longer pipelines the mixture must remain stable without motion for periods as long as several hours to avoid pipeline plugging. The fine particles in a paste mixture can be composed of mine tailings or naturally-occurring clays, silts and fine sands. The mineralogy of the particles thus can have a wide variety from quartz and feldspar to clays, micas and even salts.

Jan 1, 1993

By D. E. Walsh

The behaviour of gold particles on a spiral was studied using radioactive gold tracers. The method allowed the effect of particle size, particle shape, pulp density, feed rate, and splitter settings to be studied. Although the method has been successfully applied to other gravity concentrators, it was found that reliable results were more difficult to obtain on the spiral. However, these preliminary results show that provided suitable precautions are taken, the technique is capable of providing valuable information that cannot be obtained by conventional studies, and could be used to better optimize spiral performance.

Jan 1, 1992

By V. F. Swanson

M&MP, Volume 6, No. 4, November 1989, pp. 190-196

Jan 1, 1990

By L. Alan Weakly

Page one is missing from book

Jan 1, 1982

By Vljay K. Chhipa

Artificial intelligence is" an emerging technology in the field of computer application. Expert system have been developed to imitate human intelligence and reasoning process. Expert systems have much scope of application in the decision making process in mineral exploration as such decisions are highly subjective and expert opinions are very helpful. This paper presents a small expert system to analyze reasoning process in exploring for uranium deposits in sandstone.

Jan 1, 1989

By Marina K. Peshkova, Izabell V. Pomorova

Computer modelling system for definition optimal way of in- vestment under condition of diverse directions of activities mining enterprises has been created. The main purpose of paper is to introduce the new scientific approach of finding effective variants of investment for mining industry under free market condition in Russia, it can be also interesting for domestic and foreign investors.

Jan 1, 1996

By W. J. Halvorsen

Means for minimizing the disadvantages of thermal drying are suggested. The other ap¬proach of substituting other techniques in place of thermal drying is also discussed. Recent devel¬opments in fine coal screening dry down to 3.2 mm (0.125 in.) and 2.0 mm (10 mesh) offer an econom¬ical means in certain cases.

Jan 1, 1988

By Garry W. Stevenson

Data from many case histories reporting tunnel boring machine penetration rates in rock with unconfined compressive strengths greater than 70 MPa (10,000psi) are summarized. The case history data are useful for comparing estimated penetration rates with historic performance in similar rock types, particularly in granitic and metamorphic rocks. TBM exhibit higher penetration rates in sedimentary rocks than in granitic and metamorphic rocks. Data for the two groups of rocks are summarized separately.

Jan 1, 1999