Search Documents

By Libby R. Ricafort, Victorio V. Pato, R. S. Pizarro

Introduction Atlas Consolidated Mining and Development Corp. (ACMDC) started gold production at its Masbate gold mine early in 1980. This involved an open-pit mine and a 3.5-k/d (3850-stpd) carbon-in-pulp processing facility (Pizzaro and Antonio, 1981). When this operation started, the mine began stockpiling sub-grade milling material averaging 1 g/t (0.029 oz per st) gold. Furthermore, geologists estimated that there were additional low grade reserves within the ultimate pit limits. These amounted to 2.4 Mt (2.6 million st) with an average grade of 1.1 g/t (0.03 oz per st) gold. The success of low cost heap leaching prompted an investigation to determine if this tech¬nique would be applicable for the low grade Masbate ore. The findings were favorable and a series of laboratory tests were undertaken. These tests indicated the amenability of this subgrade milling ore to heap leaching. Depending on ore size, gold extractions of more than 60% were obtained. To further define operating parameters for a commercial heap leaching plant, a 400-t (440-st) batch pilot plant was built and operated. These test results were used to design the first commercial heap leaching plant in the Philippines. One design concern was the control of solutions during the rainy season. Due to the material's low grade, every effort was made to minimize capital and operating costs. To this end, surplus mining equipment from the copper operations of ACMDC and used machinery in the crushing circuit were considered. Location: The Masbate gold heap leaching operations are located on the northeastern part of Masbate Island, Philippines. This is about 480 km (300 miles) south-east of Manila. Climate: The climate is moderate with two distinct periods. The dry season runs from January through June, and the rainy season extends from July through December. During the wet season, the rainfall at the mine site averages 300 mm/m (11.8 in. per month) for a total of about 2000 mm/year (78 in. per year). However, heavy downpours in excess of 100 mm/h (4 in. per hour) can occur. Geology: Four distinct rock types have been identified in the pit area. They are tuffaceous agglomerates, andesitic agglomerates, metasedimentary rocks, and hornblende augite andesitic porphyry. The tuffaceous agglomerate occupies the northern and western flanks of the mine. Andesitic agglomerates are localized distinctly in the central portion of the volcanic plug within the mine site. The eastern boundary of the mine is occupied by metasedimentary rocks, whereas, the hornblende augite andesitic porphyry occurs as an intrusive within the andesitic agglomerate and tuffaceous agglomerate. Some areas of the pit contain high proportions of clay minerals, requiring an agglomeration step in the flowsheet. This ensures satisfactory percolation through the heaps. Ore characteristics: Gold and silver are microscopically dis-

Jan 9, 1987

According to the classification of water conservation mining in shallow coal seams in China, when the ratio of the impermeable layer thickness to the mining height is less than 18, the mining belongs to the category of special water conservation, and the strip backfilling mining method is employed. This study is based on the geological conditions in northern Shaanxi. By analyzing the stability of the impermeable layer, the stability criterion of the impermeable layer was developed. The study also investigated the compositions and properties of the backfilling materials. The results show that reasonable subsidence of the impermeable layer is allowed during mining under the basic precondition (upward cracks and downward cracks are not connected).

Jan 7, 2020

By Morteza Gharouni Nik

Flexible Dilatometer Test (FDT) is one of the in-situ test methods for determining the deformational characteristics of rock masses. In this study, several dilatometer tests have been conducted in different geotechnical phases of site investigations by means of two types of FDTs. The purpose of this paper is comparison of the performance of these two types of dilatometers and analysis of the differences in the results of the tests.

Jan 1, 2008

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers' handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

By William D. Leech

Lebanon used a TBM for the firsttime to excavate a tunnel in the country. A main beam TBM, built in 1979, bored the 3.8 m (12.5-ft) diameter by 4,020 m (2.5-miles) Madiq Tunnel. The TBM bored through karstic terrain of dolomitic limestone, limestone and marly-limestone rock having near horizontal beds with more than twelve faults crossing the axis of the tunnel. The TBM also encountered more than six major karst features, filled with various combinations of boulders, clay, void space and water. The excavation through these collapsed-breccia zones drastically slowed the TBM?s progress. When complete, which the Madiq Tunnel is a part, the Kesrouane Water Project along the coast will bring fresh and irrigation waters to the parched and heavily populated region north of Beirut. The paper will describe the tunnel geologic features, karst genius, TBM upgrades and performance, and TBM/karst difficult situations

By William H. Hansmire

The Modified Detroit River Outfall No. 2 (MOD DRO-2) will discharge treated wastewater to the Detroit River. Construction of a 6.4-m-diameter, 1.9-km-long tunnel was halted in 2003 by flooding during tunneling with an open face hard rock TBM. A new design for a higher rock tunnel, a ?Modified? design, was completed in 2007 and Notice to Proceed to the tunnel contractor was given in November 2008. Project duration is four years for completion of tunneling and start of outfall tunnel operation. This tunneling project has high groundwater pressure (5 bar), pervious limestone rock of up to 140 MPa (20,000 psi) strength, and hydrogen sulphide in the groundwater. The new tunnel will be connecting to access shafts and outfall diffuser riser shafts previously built for the now-abandoned tunnel. The new tunnel design construction contract, and initial planning to use a pressurized-face (slurry) hard rock TBM are presented.

By D. Gu

Shaft drilling is one of the most useful methods of driving shafts. This paper describes the application and development of the technique in coal mine construction in China.

Jan 1, 1993

By Jon Hurt

INTRODUCTION The entire scope of new facilities for Lake Mead Intake No. 3 includes a sub-merged intake structure, a deep tunnel beneath Lake Mead, a tunnel access shaft, Intake Pumping Station No. 3, and connections to an existing intake and water treat-ment facility, as shown in Figure 1. In March 2008 Vegas Tunnel Constructors (VTC), a joint venture of Impregilo SpA and SA Healy were awarded a $447m Design-Build contract by SNWA for a section of this work (Contract 070F 01 C1), including the 185 m deep tunnel access shaft, the 4.7 km long, 6.1 m diameter tunnel and the submerged intake. Arup, supported by Brierley Associates, is the Design Engineer for VTC. The scope of the work is shown in Figure 2. This paper will describe the design and construction on this contract, with a focus on the access shaft which is the most complete section of the work. The shaft is being sunk using drill-and-blast methods with the finallining placed as excavation proceeds. The shaft passes through a major fault zone, and extensive pre-excavation grouting for water control is required for much of the depth of the shaft.

By Karen Mikkola, Gerald Luttrell, Jaisen Kohmuench, Glen Oswald, Michael Mankosa, Tracy Westerfield

Hydraulic separators are commonly used for particle size classification and gravity concentration of minerals and coal. Unfortunately, the efficiency of these processes can be quite low due to poor equipment design and variations in feed consistency. To help alleviate these problems, an industry-driven R&D program has been undertaken to develop a new generation of hydraulic separators that are more efficient and less costly to operate and maintain. Two of the most promising technologies, the CrossFlow and HydroFloat separators, have now been tested at industrial sites. The data obtained from these sites have been used to illustrate the potential performance improvements that can be realized through the application of these high-efficiency separators.

Jan 1, 2005

By Christopher Mark

Sixty years ago, underground coal mining was the most hazardous job in the United States. Roof falls were a big part of the problem. They killed about 100 miners every year, more than all other causes put together. Fast forward half a century to 2016, which is the first year ever with zero roof fall fatalities. Just three miners were killed by roof falls during the following 6 years. How was this historic goal achieved? This paper starts with a modern analysis of the causes of the roof fall fatalities in 1968. Then it follows the reductions over time by category, using snapshots of the fatalities occurring in subsequent decades. Along the way, it evaluates the influence of the regulatory environment, changing mining methods, and better ground control technology. The paper shows that in 1968, more than half of roof fall fatalities at large mines were attributable to an inadequate safety culture. The immediate effect of the 1969 Coal Mine Health and Safety Act was to reduce the riskiest activities, like needlessly going under unsupported roof. Other hazards, like large roof falls, required technological developments before they were brought under control. Roof control plans, which the U.S. Bureau of Mines had been advocating since the 1920s, played a significant role throughout the process.

Jul 1, 2023

By Ashis Bhattacherjee, Rahul Upadhyay, Nearkasen Chau, Aditya Kumar Patra, Dhanjee Kumar Chaudhary

Heavy earth-moving machineries used in open-pit mines intensively expose the drill operators to whole-body vibration and shocks and thus to musculoskeletal disorders. The roles of an individual, machine, and rock-related factors in their exposure remain poorly understood. This cross-sectional study investigated their role among 39 drill operators from Indian iron ore mines. It shows that 70% of the operators were exposed to high levels of vibration, above the limit values recommended by ISO 2631-1. Multiple linear regression models showed that the whole-body vibration and shock exposures were strongly associated with operator’s age, drill machine model, rock’s hardness, uniaxial compressive strength, and density. The role of body mass index was close to significance (p = 0.08). Univariate analyses found that drill’s age, seat pad thickness, and seat backrest height were also strong predictors. These results help in identifying risky operators, materials and occupational situations, and in implementing appropriate prevention and intervention to reduce and monitor the exposures and health risk.

By W. Kracht

Frothers are surfactants used in floatation to aid generation of small bubbles. Studying events at the moment of bubble creation is a challenge because of the short time frame. This presentation introduces a novel acoustic approach. The technique has the resolution capable of detecting events that occur within 1-2 ms. The transition from coalescence to non-coalescence is tracked as a function of surfactant concentration and gas rate through the capillary. Results are given for some common flotation frothers and n-alcohols (C4-C8). A stress model is used to give a qualitative explanation to the observed action of frothers on coalescence prevention. Results for salt (sodium chloride) are included for comparison).

Jan 1, 2009

By C. C. Russelll, V. T. McLemore

The Metals Mining Sector of the Acid Drainage Technology Initiative (ADTI-MMS) addresses technical drainage-quality issues related to metal mining and related metallurgical operations, for future and active mines, as well as, for historical mines and mining districts. One of the first projects of ADTI-MMS is to develop a handbook describing the best sampling, monitoring, predicting, mitigating, and modeling of drainage from metal mines, pit lakes and related metallurgical facilities based upon current scientific and engineering practices. One of the important aspects of planning a new mine in today’s regulatory environment is the philosophy of designing a new or existing mine or expansion of operations for ultimate closure. The holistic philosophy taken in the ADTI-MMS handbook maintains that sampling and monitoring programs should be designed to take into account all aspects of the mine-life cycle. Data required for the closure of the operation are obtained throughout the mine-life cycle, from exploration through post-closure.

Jan 1, 2004

By J. Gentry

Chemical grouting has been successfully used for over forty years to control the movement of groundwater in a wide variety of applications including tunnels, subway systems, sanitary sewers, mines and construction projects. This paper illustrates the versatility of chemical grouts by reviewing three projects where chemical grout was utilized to address some very difficult water control challenges. The featured product is acrylamide which can be used alone or in conjunction with other types of grout such as cementitious products. Acrylamide grout is injected as a two component product that will react and form an impermeable gel when the components combine. There are notable differences between the acrylamide based products and cementitious products. The most notable and significant difference is that acrylamide is a true solution grout that contains no particulates and has a viscosity of 1-2cps. This feature enables the acrylamide grout to penetrate very small geological features that other grouts could not penetrate and to seal small cracks and fissures where groundwater seepage is occurring. The product also has an adjustable gel set time from a few seconds to several hours which enables the operator to determine the product travel before it forms a gel. When properly applied the product has a half-life in the soil of 362 years (per testing by the US Department of Energy).

Feb 27, 2013

By L. Clark

Despite near-record commodity prices, the mining industry continues to search for ways to maintain profits in these times of steadily increasing energy prices and steadily decreasing grades. The pressure is still on today’s miners to continuously improve their operations because they know that one day prices too will drop. Some, however, have seized the opportunity to employ systematic methods to reduce costs and increase the efficiency of their workforce and equipment. As a result, closer attention is being paid to scheduling and the value that could be added by defining the extraction sequence that maximizes the net present value [NPV] of a project. This paper will discuss the challenges faced by Newmont Mining Corporation [Newmont] at its operations and the application of sophisticated software tools and methods in its search of solutions to this problem.

Jan 1, 2007

By CASSANDRA L. HOEBBEL, Jennica L. Bellanca

High-fidelity, immersive training is known for its learning and logistical benefits. While other industries have used virtual reality (VR) for decades, the same uptake has not been seen in mining. NIOSH recently developed an adaptable, scalable VR training platform, VR Mine Rescue Training (VR-MRT), which has attracted significant industry interest. NIOSH is using VR-MRT to understand the barriers to adoption and implementation of VR. As a part of a larger effort to assess the effectiveness and implementation of VR-MRT, researchers have conducted pre-implementation interviews. In this paper, the authors use feedback from individuals at various implementation levels to assess the acceptability and appropriateness of VR-MRT and identify potential implementation barriers for VR more generally. Researchers also describe ongoing efforts to overcome these barriers as NIOSH works to position VR-MRT as a supplemental resource more generally for mine safety training.

Feb 1, 2025

The authors summarise the development and recent advances in the reconstruction and visualisation of three-dimensional objects from point data and describe applications to the reconstruction of orebody shapes from drill-hole and other data. In particular, Dijkstra's algorithm is proposed and implemented as a means of optimal reconstruction of complex orebody and topographical shapes from irregularly located sample data. The surfaces of the shapes are constructed from triangular tiles and the algorithms proposed by the authors are guaranteed to find the optimal set of tiles that "best" construct the surfaces on the basis of specified objective criteria. The algorithms are illustrated by applications to a complex silver/gold/zinc/lead deposit.

Jan 1, 2002

By Günther M. Volkmann

Continuous developments in tunneling require knowledge transfer between designers and suppliers to optimize the application of support systems. This collaboration allows the designer access to the latest research results, technical innovations, and support specific measurement techniques as well as the supplier?s experiences on recent projects. Project specific requirements determine the information that can be used to increase support system efficiency, advance rate, degree of safety, or decrease costs. This cooperative effort results in not only an unambiguous tender document, but also an optimized design with reduced risk that is coordinated with safe and high performance construction techniques. This paper will address the benefits of an early collaboration to both the design and the specifications in the tender document by using the A3 Hindhead project (UK) as an example.

Jan 1, 2008

Caterpillar’s 797 327-t (360-st) mining truck is currently being tested at the company’s proving facilities. Mine evaluations began in the second quarter. The unit will be commerically available in North America in 2000 and worldwide in 2001. The new model is the largest of Caterpillar’s off high-way truck line. In addition, the company has replaced its 966F series II and 970 F wheel loaders with the966G and 972G models. 797 mining haul truck Caterpillar developed the 797 mining haul truck in response to mining companies seeking to reduce cost per ton in large-scale operations. The 797 is sized to work with loading shovels used in large mining operations. And Caterpillar will match the body design to the material being hauled, to optimize pay-loads.

Jan 1, 1999

By Jimmy Thompson

The Santa Clara Valley Transportation Authority is designing the Silicon Valley Rapid Transit Project in San Jose, California. The project includes 6.9 km (4.3 miles) of twin-bored tunnels to be constructed through downtown San Jose using two earth pressure balance machines (EPBMs). This paper begins with a project description and update of the project status followed by a description of the relationship between anticipated ground conditions and EPBM requirements. Topics addressed include soil conditioning, abrasion resistance, annulus grouting, face pressure estimation, additional pressure control devices and control measures to limit over-excavation and settlement.

Jan 1, 2008