Search Documents

By Jim Morris, Davin Ishii

The major source of water for Southern Nevada is Lake Mead. However, the existing pump station located on Lake Mead is inadequate for one of the fastest growing areas in the United States. In order to keep up with the increasing demand for water in Las Vegas, a parallel system is being constructed. The intake for this system is being constructed approximately 68.58m (225ft) below the surface of Lake Mead. The lake tap consists of installing casing and secant piles to support the shaft collar, excavating a 21.34m (70ft) deep intake shaft, and installing a3.66m (12ft) diameter steel liner.

Jan 1, 1999

By M. C. Roberts

To assess the future markets for a mineral from a producing district, the following three aspects must be considered: the future growth of the markets, the competitiveness of the district in terms of production costs and reserve adequacy, and the competition from alternative sources of supply. This paper focuses on the first issue by developing a method for predicting the demand for phosphate from trends in the major market for phosphate products, the fertilizer and agricultural market. The paper shows how broad changes in this end-use market for phosphate has evolved over time. These trends are then projected into the future to make an assessment of future phosphate requirements.

Jan 1, 2000

By William C. Beebe, Russell E. Martin

An account of driving and concreting two 900 m railroad tunnels for the Denver and Rio Grande Western Railroad under emergency conditions. Details the importance of on-site decision making by the Owner in completing the project successfully in record time. A general description of the geology and construction methods. The Thistle Drainage Tunnel drained water impounded behind the Thistle slide and serves as permanent diversion of the Spanish Fork River and Thistle Creek around the slide area. The project involved 684 meters of 5 m horseshoe tunnel, a 5 m diameter raised shaft and 23,000 cm of cut excavation.

Jan 1, 1985

By W. Setzepfandt, J. Henneke

PREFACE Debris disposal can very often be a severe problem and major restriction on tunnel boring projects, especially for small diameter tunnels and in underground mines. Hydraulic transport could provide a suitable solution. Investigations have therefore been made in connection with a full-scale project of 4.8 km length and 2,3 m diameter, to obtain the required technical and economical data for planning an optimized transport system, e.g. for a tunnel boring drivage of 6 - 7 m diameter in underground coal mines. INTRODUCTION The Radau-Tunnel, chosen for the investigations, has been designed for transferring flood peaks between the rivers Radau and Grosse Romke in the Harz-Mountain of Lower Saxony. A DEMAG TVM 20/23 H tunnel boring machine was used to drive the tunnel on a rising gradient of 0,53 %. The rock consisted of shale and hornblende (55 %), granite (15 %), diabase (15 %), chert (8 %) and gabbro (7 %). The project has been sponsored by the Federal Ministry of Research and Technology.

Jan 1, 1981

By O. A. Bascur

The problem of setting the proper control objectives and/or having several objectives to be met in the implementation of grinding control strategies can be resolved. The design and implementation of a distributed control system for safe operation of a grinding circuit while maximizing profit is presented. An optimal recovery through- put target for a desired grind is accomplished by advanced control strategies at the DCS level. A mill load constraint control technique provides stable operation with a substantial increase in throughput, while the desired grind index is maintained by an inferential grind control technique without using a particle size analyzer. The integration of crushing/grinding and flotation in the overall design was the key to the success of the project. This synergistic effect was obtained by implementing a computer plant management system in the concentrator. The overall/philosophy was to keep the implementation simple while using new technology creatively.

Jan 1, 1991

By Frank L. Bazzanella

Se presenta una breve introducción de la concentración gravimétrica, incluyendo alguna discusión sobre los minerales mas comunes recuperados normalmente. Se mencionan las consideraciones importantes para el diseño básico de una planta de concentración y se presentan cuatro esquemas de flujo sobre las operaciones más corrientes. Las plantas estudiadas en detalle incluyen: "Climax Molybdenum Co. By-Product Plant" y "Canada Tungsten Ltd. Plant". Las plantas brevernente reseñadas incluyen: "Palabora Mining Co. Uranium Recovery Facility" y "Bridge Hill Ridge Heavy Mineral Recovery Plant of Mineral Deposits Ltd."

Jan 1, 1982

By J. Partyka, Trevor R. J. Kelly

This paper presents the results on noise testing of a fan only, as well as the results of a steel silencer and of flexible silencers that were connected directly to a fan. On-site facilities and free-field method set by the British Standards Institution were used to measure and then compare the fan only and different practical silencer configuration setups. In order to determine the fan-silencer combination that would give the maximum noise attenuation, total noise intensity, noise contributed to by the fan motor only, as well as aerodynamical noise created through air interacting with the fan parts were considered to obtain decibel readings for the octave bands. Subsequently, the optimal configuration found was the setup with flexible silencers on the fan inlet and the fan outlet. If only one silencer is used, it should be installed on the fan inlet. The aerodynamic noise affects the low frequencies. The flow noise is then overtaken at 1 kHz by the mechanical noise.

Jan 1, 1995

By Roshan B. Bhappu

In situ mining and extraction is one of the Frontier Technologies that is destined to play an increasingly important role in the recovery of metals and minerals in the future. This premise is based on increasing costs of labor and energy, increasing awareness of environmental considerations and decreasing ore grades in the United States. Up to now, in situ mining has been successfully applied to a few favorable situations for the extraction of some evaporites, copper and uranium. However, because of its unique technical, environmental and economic advantages, this versa tile technology will find broader applications for the recovery of above commodities as well as for others which are currently extracted by hydrometallurgical means. This paper traces the development of in situ mining and extraction; stresses its dependence on interdisciplinary science and engineering; discusses its theoretical, practical and economic aspects; and finally presents potential applications of this Frontier Technology.

Jan 1, 1985

By S. Mason

Many organizations are realizing that continual improvement in health and safety relies on addressing the potential for various forms of human error. Of these, rule violations are often the most frequent form associated with accidents. These occur when an individual (or individuals) deliberately contravenes established and known safety rules. They have been associated with up to 90% of the accidents and other incidents in some industries, and yet they rarely receive the systematic attention they deserve in the promotion of safety. This paper presents underlying motives that cause violations. These can vary significantly from mine to mine and from job to job. Managers need some measure of the attitudes of the violators to determine the underlying motives behind the violations if they are to determine effective strategies for promoting safe behavior. Questionnaires form the starting point to address attitudes and the motives behind rule violations. The choice of the most suitable questionnaire, how- ever, will vary from organization to organization. Guidelines on the choice of questionnaire are offered.

Jan 1, 2000

By Jean-François Bougard

It has already been said and written many times that the construction of tunnels in urban areas has proved more and more indispensable, if not vital. The subsequent development of tunnelling for 15 or 20 years has brought large and sometimes spectacular improvements in the fiel of execution methods. But, particularly in urban areas, the difficulties to be overcome have been and still remain very important. As a matter of fact, most of big cities, have been settled near rivers or lakes; therefore the geological nature of the subsoil is soft ground and the level of ground water is high. As a consequence, tunnelling is often faced with many well-known difficulties and dangers issued from decompression or loosening of the ground, sometimes accompanied by a lowering of the water table. This may compromise the safety of the excavation itself and of the workers, and also cause settlements which many severely damage nearby buildings or structures. This is the reason why it is always necessary to work out specially adapted methods and even to develop new ones. In most cases, each work is a particular one and has to be specifically studied since numerous data are to be taken into account, related not only to geology, cohesion and behaviour of the different layers concerned, ground water, the activity of it, but also to

Jan 1, 1979

By S. K. Kawatra

With the increasing importance being placed upon modernizing the coal industry as a result of recent developments in the international energy balance, computer control has been and is being instituted in many coal cleaning plants. Control techniques that are well established in many base metal industries have been adapted to coal washing. Essential to any control scheme is an accurate measure of the parameter which is to be controlled. A sensor is required that will provide information both quickly and precisely. In fine coal circuits, the critical parameter that must be measured and controlled is the per- cent ash contained in the clean coal product and tailings. Measuring the ash content of these slurry lines on a continuous basis enables the operating conditions in the circuit to be adjusted so as to obtain optimum separation efficiencies at all times. An on-line ash monitor has been developed and tested at Michigan Technological University which is capable of making percent ash and percent solids determinations instantaneously. Two radioisotopes are employed in this system to generate signals that can be related to the density and the ash content of the slurry. Such data provide a means to execute a short term control strategy.

Jan 1, 1982

By I. S. Parrish, D. W. Kappes, G. G. Austin

Micron-sized gold disseminated in lower Cambrian siltstone has been found at the Sterling mine near Beatty, NV. A shoestring-shaped body has been developed by central and fringe drifts and is being mined via a modified retreat room and pillar system. The siliceous ore crushed to 5.08 cm (2 in ) is stacked to 4.6 m (15 ft) over a layered sand, gravel, and impervious PVC base. Gold is leached using a 0.1% cyanide solution and deposited on activated coconut shell carbon. Stripping of the carbon by hot solutions of 1% NaOH and 20% Ethanol yields overall recovery of about 75% of the fire assay head.

Jan 1, 1983

By Robert J. Timko, R. Lincoln Derick

This report presents a Bureau of Mines evaluation which examined the extent of gas leakage from sealed areas in underground coal mines and measured the effectiveness of commonly used structures for controlling the quantity of gas exchange from these areas. Evaluations were performed on five abandoned areas in two operating underground mines within the same coal seam. Methane and oxygen levels inby the seals were monitored to determine if the gas leakage was unidirectional or bidirectional. Results from this and prior work dealing with minimizing gas leakage were then applied to a newly abandoned area. Also discussed are bulkhead site preparation, construction plans, techniques for monitoring the status of the atmosphere within the sealed volume, and a modified European method for controlling gas migration from the sealed volume to the active mine.

Jan 1, 1991

By William P. Barnett

In 1988, the US Department of Energy's (DOE) Pittsburgh Energy Technology Center identified three coal cleaning options for achieving flexible environmental control strategies aimed at reducing energy-related SO2 emissions. These are selective agglomeration, advanced froth flotation and advanced cycloning. Each relies on maximum liberation of pyrite and other mineral matter through feed coal comminution to fine and ultrafine sizes. The National Energy Strategy (NES) and the Clean Air Act Amendments (CAA) of 1990 are examples of the nation's commitment to a clean environment. The need to use the nation's energy resources in an environmentally sound manner presents critical challenges and opportunities for coal preparation during the next decade, particularly regarding the control of SO2 emissions. The principal challenge is the development of cost-effective coal preparation approaches for sulfur removal beyond currently achievable levels. Opportunities are provided in the form of incentives associated with a novel system of SO, allowances and a policy environment based on the proper functioning of familiar market forces. An allowance, as defined in Section 402(3) of the Amendments, is "an authorization ... to emit ... one ton of sulfur dioxide." To achieve the objective of the Clean Air Act Amendments, SO, emissions will be eventually capped at 8.12 Mt (8.95 million st) annually by controlling the number of allowances issued nationally. By permitting allowances to be bought and sold once issued, the law encourages "overcompliance" as a source of profit for owners of excess allowances. Many details concerning the administration of allowance trading are not yet written.

Jan 1, 1992

By Paul J. A. Lever

The mine environment is dynamic and operating conditions change continually and are difficult to predict. New equipment, variable geological conditions, modified layouts, and different equipment operators make monitoring and control system difficult to apply without continual software maintenance. The paper reports on algorithms that were developed, encoded with Knowledge Craft Tools, and tested on underground coal mine data to adapt to the dynamic environment. The system receives data from sensors in near real time and then identifies patterns in the data. Using a set of mode features the data is automatically checked to determine the present operating mode. When the operating mode changes from the previous shifts, the system automatically learns the new mode characteristics and uses that mode context for further data analysis. The concepts presented in this paper are applicable to a wide variety of mining scenarios, not just underground coal mining.

Jan 1, 1992

By H. Nakazawa, A. S. Malicsi, K. J. Reid, P. J. Ryan, I. Iwasaki, P. W. Weiblen

Precious metals are commonly believed to be recovered along with sulfide minerals in flotation, but a few neutron activation analyses showed that the recoveries of gold and silver were unexpectedly low. Reasons for low recoveries of platinum group metals remained unresolved due to interferences in the analyses. Electron microprobe, scanning electron microscope, and scanning Auger microprobe analyses have identified nickel arsenide minerals in the ore and confirmed a close association of platinum group metals with the arsenide minerals as minute inclusions. These results indicated a need for re-evaluation of flotation procedures that have so far ignored special problems related to arsenide minerals. The electrochemical and flotation behaviors of nickel arsenide and their application to the flotation recoveries of precious metals from copper-nickel bearing Duluth gabbro are presented.

Jan 1, 1987

The need for geological control in orebody estimation and modelling is self- evident to geologists and mining engineers engaged in practical day-to-day estimation. It is only fairly recently, however, that attempts have been made to incorporate explicitly such requirements into published accounts of geostatistical estimation; see, for example, Dowd and Scott (1982, 19841, Rendu and Readdy (1982), Dagbert et al. (1984), Dowd (1984), Benest and Winter (1984). In practice, many geological controls in automatic or semi-automatic estimation and modelling are essentially geometrical controls. The aim of this paper is to present two techniques for geological/geometrical control. Whilst the applications are new, neither technique is entirely original and both have been adapted from other fields and sources. Both techniques are, in some sense, types of estimators and/or interpolators of shapes. The first is a method for fitting spline surfaces to control orebody boundary estimation and to unroll orebodies. The second is an application of Minkowski addition to interpolate shapes such as orebody outlines or stope boundaries and to control estimations.

Jan 1, 1986

By Brian Flintoff

Basic process control is an integral part of most mineral processing plants. It is widely acknowledged to have helped many operations reduce costs and increase productivity and performance. The research community is very active in the development and evaluation of both model based and Al techniques for advanced control applications. Vendors and specialist consulting or engineering firms are in business to help deliver these solutions to the plant floor. It would seem that there is a good balance between business needs and technology, and that the industry should be moving steadily forward in an aggressive pursuit of plant-wide automation. However on closer examination one sees some systemic problems which are sewing to inhibit progress. One of the mist obvious manifestations is the gap which exists between the available technology and current This paper explores the control of mineral processing systems, with a particular emphasis on some of these problem areas.

Jan 1, 1995

By G. T. Adel, W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphulerite and dolomite, has been used to experimentally validate the model for the case of dry batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1988

By Keith G. Wallace, Robert Wise, Ian J. Duckworth

This paper describes a case study for the ventilation planning at Utah Fuel Company's Skyline Mines which are located outside Price. Utah. The Skyline Mines are currently comprised of two longwall coal mining blocks located in two different mines. A third replacement longwall block is currently being developed. Future ventilation systems for the mines were determined by establishing ventilation models developed from data collected during a detailed ventilation survey. The paper discusses the challenge to coordinate immediate ventilation requirements with long-term demands. The continuous movement of the longwall, which frequently represented the only open split in the ventilation network, resulted in cyclic ventilation demands dependent upon the length of the tailgate. A series of system configuration changes were recommended based on the results of the network modeling exercise and an economic evaluation of the various options. The scope and cost of the configuration changes, and the mead improvement resulting from these changes is discussed.

Jan 1, 1995