Search Documents

By S. Majumder

The longwall face supports are provided to prevent the caving of the immediate roof at the working face. The thickmess of the immediate roof may be obtained from the working height and the average bulking factor. A strong bed, capable of withstanding maximum bending moment among the beds within the above roof, can be identified. The load on the strong bed may be obtained by finding out the overlying beds that will rest on the former during sagging. The limiting span, L, for this unsupported loaded bed, as a beam with built-in ends, can be calculated. The support density required at the supported span (face to goaf edge), a, during the first fall, is now estimated with a view to have a safety factor 2 at the face end, when bending failure occurs at the barrier end. However, the above value is inadequate to provide necessary safety margin against bending failure at the face end, during the subsequent cavings as cantilever, for L/a less than 20.6. d For the latter case a separate expression is derived.

Jan 1, 1986

By John A. L. Dr. Campbell, James W. Haskew, F. Hoy Lee, Elliott P. Dr. Doane

Emissions of particulates, unburned hydrocarbons, nitrogen oxides (NO[ ]) and carbon monoxide (CO) from diesel engines are of concern in mines, particularly underground mines. All these undesirable products except NOx are the result of incomplete combustion in the cylinders. Various approaches to achieving more complete combustion in diesel engines have included different fuel compositions, use of catalysts, fuel additives, engine modifications, and oxygen-enriched intake air. The present study shows that injecting minute quantities of primarily platinum group metal catalysts into the intake air of a Deutz/MWM D916-6 mine diesel engine substantially reduces emissions in the exhaust. The catalyst injection system, which was developed by National Fuelsaver Corporation (Robin. 1981), transfers catalyst compounds in solution to a stream of air bubbles by a process called Bubble Fractionation (Lemlich et al.. 1966, 1968. 1970). The amounts are so minute that concentrations in the engine exhaust should be well below OSHA/NIOSH Time Weighted Average (TWA) exposure limits at steady state, a fact that was confirmed by analysis of collected particulates in the exhaust. When the catalyst injection was used along with a pleated paper filter to remove exhaust particulates, the filter operating life was shortened greatly. Therefore, this system is not recommended for use on diesel engines equipped with a water scrubber and a filter. It does offer a practical and relatively economical way of reducing exhaust emissions from other diesel engines, such as those in outby mine service

Jan 1, 1995

By R. J. Pugh

The surface chemical sites on several fillers (quartz, feldspar, calcite and granite) were studied by the adsorption of well defined acid and basic probe molecules (benzoic acid, benzyl alcohol, ethyl benzoate, pyridine and benzyl amine) from cyclohexane. The results provided a wide variation of adsorption data, emphasizing the extensive range of site heterogeneity on the filler surfaces. In addition, it was shown that the acidic probes were strongly adsorbed on all of the minerals, thus indicating that the basic surface sites dominate the acidic ones. Also, through FTIR studies with vapor-phase probes adsorbed on orthoclase, it was possible to identify the nature of specific sites and the type of bonding occurring between the filler surface and the probe molecule. These types of surface analytical techniques could give useful information for predicting the adsorption functional groups on dispersants, dyes, thickeners, etc. and could lead to enhanced interfacial bonding between the filler and the matrix.

Jan 1, 1993

By Robert Snow, Yingxue Yu, Patrick Zhang

The FIPR/SAPR process is FIPR's third approach to develop a viable alternative to the Crago "Double Float" process for phosphate flotation. SAPR stands for Single-collector, All-anionic Phosphate Recovery. The FIPR/SAPR process - offers a universal flowsheet for any anionic reagent system and flotation feed of varying sizes. For an unsized or fine flotation feed, the FIPR/SAPR process consists of the following steps: 1) high-solids conditioning with an anionic collector; 2) anionic rougher flotation, with the rougher concentrate sized at 48 (or 65) mesh and the +48 mesh recovered as a final product; and 3) cleaning flotation of the -48 mesh fraction from step 2. In a variation of step 2, the rougher concentrate from the first two cells may be collected as a final product, and the rougher concentrate from the last two cells sized at 48 or 65 mesh. The new process was tested with a blend of anionic collectors, achieving single-digit Insol at 85 + % recoveries.

Jan 1, 2002

By S. I. Nozhko, V. N. Guliy, A. A. Zolotarev, L. M. Luyshnia

The study of the apatite deposits of the Aldan Shield shows wide spread of the Precambrian apatite-carbonate ores and possibilities of using them for extraction of apatite. Dependency of flotation on ore minerals was studied according to the following scheme: preparation of the monomineralic samples of anhydrite, gypsum, chlorite, serpentine, phlogopite, apatite; mixing them in apatite ore of the average composition; followed by flotation. Another series of the experiments was conducted to ascertain a dependence of flotation activity of the different minerals on the different flotation reagents, which were used as collectors. It has been shown that apatite from silicate-carbonate ores is most extractable because it has the biggest size of grains and is the most free of inclusions. Beneficiation of the sulphate-containing apatite-carbonate rocks is possible when flotol - 7.9 is used as a collector. Meanwhile, the use of the tallaktam leads to an increase in the sulphate recovery. The estimation of individual technological features of the layered Mghydrosilicates and their influence on the process of beneficiation has been examined using samples of apatite-dolomite ore (P205-8%) with the addition of the phlogopite, serpentine and chlorite. The results show that there is little influence of the chlorite presence on the flotation while the serpentine presence leads to a decrease of the flotation, because of its high specific surface area.

Jan 1, 1993

By Cheryl M. McInnes, Graham J. Sparrow, James T. Woodcock

Three composites, assaying about 3 g/t Au and 0.75% Cu, were investigated. Each contained oxide copper minerals, iron oxides, and silicates. One composite also contained copper and iron sulphides. Maximum gold extractions by thiourea leaching were obtained after copper removal by acid pre¬leaching at pH 1.5 and redox potentials of 400 mV (Pt versus SCE). Best thiourea leaching conditions were pH 1.5, redox potentials over 200 mV, and 0.4% thiourea. This gave 90% gold extraction in 2 h with thiourea consumptions of 25 kg/t. Lower potentials gave poorer extractions. Ferrous iron additions before leaching halved thiourea consumptions. Longer leach times and the presence of sulphide minerals sometimes resulted in reprecipitation of gold.

Jan 1, 1989

By E. Pardo-Igúzquiza

Most mining applications of geostatistical simulation are to the simulation of quantitative variables, such as grade. In many instances the occurrence of quantitative variables and the values they take are controlled, at least partially, by qualitative, or categorical, variables. Examples include quartz-vein controlled gold orebodies and stratigraphic silver/lead/zinc deposits. In these cases a realistic simulation must include geological controls on the spatial distribution of the simulated quantitative variables. This paper describes extensions to, and algorithms for, the truncated plurigausian method of simulating categorical variables. The categorical variables are modelled as indicator random functions that represent the presence/absence of the variable at spatial locations. Stochastic images of the distributions are obtained by truncation of realisations of two Gaussian random functions simulated at the same locations. Parameters required are the thresholds for truncation of the Gaussian variables and the covariance structure of each Gaussian random function. These parameters are estimated from the experimental proportions of each variable and indicator direct and cross semi-variograms. A detailed case study is shown in order to illustrate the procedure, to discuss the results and to present the algorithms for plurigaussian simulation.

Jan 1, 2002

By B. (Manas) Das

Rock characterization for geotechnical purposes using the microhardness technique is discussed in this paper. The concept of rock characterization and its steps are logically developed. The geotechnical properties should be functionally tethered to the technological problems for characterization. The overriding geotechnical concern is rock mass stability. The important factors in this respect are rock properties, structural discontinuities, ground water, field stress, temperature and technological factors. The rock properties are the primary factors and the other factors generally affect rock properties. Of the rock properties the strength and elastic properties can form a basis for rock characterization. The microhardness technique can provide these two properties. Study on coal shows that the microhardness impressions can be used for this purpose. On the basis of this study coals of all ranks can be divided into distinct geotechnical groups. The details of these are discussed in this paper.

Jan 1, 1986

By J de Cuyper, E. J. Parkins, H. L. Shergold, W. Freyberger

The paper is divided into two parts. The first part describes an investigation of the effect of temperature on the conditioning and flotation of an ilmenite ore with a 1:l oleic acid-fuel oil mixture as collector. During conditioning the pulp underwent characteristic changes of flocculation, deflocculation and dispersion which were monitored by measuring the power consumption of the conditioner motor. Optimum flotation results were obtained at the end of the deflocculation period. High ilmenite recoveries were obtained at high temperatures and high concentrate grades at low temperatures. The second part of the paper describes a study of the effect of temperature on the adsorption of oleic acid at the ilmenite/water interface. At high adsorption densities it was chemical and exothermic. Contact angles showed that the hydrophobicity of the collector-coated minerals increased with an increase in temperature.

Jan 1, 1976

By Jean-Michel Rendu

The semivariogram is one of the most important tools available to the geostatistician for the analysis of mineral deposits. To be complete, a semivariogram study must include a minimum of three parts which are highly interdependent. These are: calculation of the semivariogram, mathematical modeling, and geologic interpretation. The known factors and conditions which controlled or influenced the distribution of mineralization within the body being studied should be considered in the analysis .of the semivariogram. The presence and characteristics of successive phases of mineralization, the chemical and physical properties of the host rocks and the mineralization should all be considered. This requires close and continued communication between the geologist and the geostatistician prior to and during the semi-variogram study. Geologic stationarity is needed if meaningful semivariogram results are to be obtained. The first step is, therefore, to determine whether the mineralization can be analyzed as a whole or if different geologically homogeneous sections must be defined and evaluated separately. Different methods can be used to calculate an experimental semivariogram from known sample values. The method chosen will depend not only on the anticipated and actual statistical properties of the deposit, but also on its geologic characteristics.

Jan 1, 1982

By R. Karl Zipf, Z. T. Bieniawski

Based on the premise that understanding the fundamental mechanics of fine fragment formation in coal will lead to reducing coal dust problems in mines, a thorough study of the mechanics of crack propagation in coal was undertaken. Two approaches were considered in an attempt to understand and quantify the fracture process as it relates to fine fragment formation. In one approach, theoretical models are used which describe the size of the fracture process zone which may relate to the amount of structural damage and fine fragment formation on the new crack surface. The other approach is based on the relationship between crack tip stress intensity and new surface appearance for mixed mode crack propagation. Preliminary observations with a scanning electron microscope support the premise that fine fragment formation is related to fracture surface appearance and fracture initiation conditions. An experimental program designed to supply the input parameters for these approaches is presently underway. The experimentation features mixed mode fracture toughness testing, using a special mixed mode testing rig, and fracture velocity measurements with a crack propagation gage. The interpretation of this data via the approaches discussed will provide further under- standing of the mechanics of fine fragment formation in coal.

Jan 1, 1986

By R. B. Coleman, T. P. McNulty

HISTORICAL PERSPECTIVE Environmental protection is not a newcomer to the minerals industry, there having been numerous examples dating from decades ago. Sometimes the awareness of a need for preservation or restoration derived from the ethics and principles of the engineers and management responsible for development and operation of a property. On the other hand, pressures to clean up industrial messes frequently were applied by special interests such as farming and ranching, recreational and conservational groups, and local governing bodies. Mineral industry environmental controls in this century have therefore been a patchwork of good intentions and bad, clean operations and dirty ones. The Hoboken siphon converter for converting copper matte while effectively capturing sulfur dioxide at a relatively high concentration was developed in Olen, Belgium in 1928, a full sixty years ago. The alternative was closure of the Hoboken smelter by Belgian government health officials who had become intolerant of sulfur dioxide emissions which were causing serious respiratory ailments in the river valley in which Olen is situated. As early as 1958, the Anaconda Company had a full-time botanist on its metallurgical research staff with the responsibility of learning how to vegetate the extensive tailings deposits at Anaconda, Montana. By that time, considerable progress had already been made in restoration of Silver Bow Creek, which at one time was “dead” for as far as 40 miles down- stream from the point of entry of acid mine drainage in Butte.

Jan 1, 1989

By J. E. Gebhardt, P. E. Richardson

External control of the electrochemical potential of a bed of mineral particles was investigated by the US Bureau of Mines as a method for controlling particle interaction with organic collectors and, thus, flotation response. A cylindrically shaped, 200- to 300-g bed of sulfide mineral particles was used as the working electrode in an electrochemical-flotation cell. In a pH 9.2 sodium tetraborate buffer, chalcocite floated with ethylxanthate at applied potentials [=] - 0.25 V (versus the standard hydrogen electrode) ; pyrite floated at potentials [=] 0.15 V. Differential separation of a chalcocite-pyrite mineral mixture was obtained by controlling the potential, but the flotation response of the mixture did not follow the behavior predicted from measurements on the individual mineral beds. Chalcocite dissolution products had a deleterious effect on chalcocite-pyrite separation by activating pyrite so that it floated below the potential (~ 0.13 V) at which xanthate is oxidized to dixanthogen. A pyrite bed activated with a copper(II) sulfate solution exhibited a flotation response with a potential dependence between that of chalcocite and pyrite. Pyrite dissolution products had no effect on chalcocite flotation.

Jan 1, 1988

By J. A. McKeown, B. M. Sanders, A. Dadgar, R. H. Sergent

This paper describes the leaching of gold with Geobrom® 3400 from a very rich (6.2 kg/tonne) black sand concentrate and its subsequent recovery by ion exchange resins and solvent extraction. The dissolution of gold from black sand ranged from 94 to 96%. Gold loadings and recoveries of nearly 100% were achieved by both ion exchange and solvent extraction methods. The kinetics and equilibrium of loading gold onto ion exchange resins and its elution from the resin were studied. The commercial ion exchange resins PAZ®- 4, DOVEX®- 21K, and Amberlite® XAD- 7, and Great Lakes Chemical experimental GLR-30 were evaluated in this work. Diethylene glycol dibutyl ether was used in all the solvent extraction work for gold recovery from Geobrom leach solution. The consumption of Geobrom was about 130 kg per tonne of the concentrate processed. Therefore, the cost of lixiviant to extract 3.11 x l0-2 kg of gold from the black sand was only about $1.00. Based on the electrochemical regeneration of bromine, the economics of bromine process vs. cyanidation were investigated.

Jan 1, 1990

By V. A. L. Breguncci, A. H. Martins, C. P. Ribeiro Jr.

This work presents experimental results for the recovery of gold present in alkaline cyanide solutions by using the electroelution technique of strong-base anionic polymeric resins IRA 402-CL from Rhom and Haas-Brazil Ltd. loaded with gold. This technique of electroelution of anionic polymeric resins is based on the removal of metal ions adsorbed to the resin, resulting from a potential difference applied between the cathode and anode in an electrolytic cell. The electrolytic cell was composed of an aqueous solution with suitable chemical characteristics and an anionic polymeric resin bed loaded with gold. The resin used in the experiments was loaded using synthetic alkaline gold cyanide solution with 1.0 g/L of gold. The variables studied were electroelution time, cathode current density, distance between cathode and anode and the electrolyte chemical composition. Statistical methods made it possible to establish the optimum conditions that would achieve satisfactory gold recoveries by the electroelution technique. The statistically predicted response for the resin loaded with gold by percolation was 16.5% gold recovery, 2.0 A/m2 cathode current density, 20-mm distance between electrodes and 6.0 hrs electroelution time. For the centrifuging system, the statistically predicted response was 7.41% gold recovery under the following conditions: 0.25 A/m2 cathode current density, 1-mm distance between electrodes, 3.5 hrs electroelution time and 10.9% NaOH in the electrolyte chemical composition.

Jan 1, 2002

By Gary A. Kordosky, R. Brantley Sudderth

The solvent extraction process as it applies to the recovery of metals from solutions on a comnercial basis is described. The four types of classes of sol vent extraction reagents are explained: 1) solvation, 2) acidic, 3) ion-pair, and 4) chelation, and examples of each type of reagent system are given. The uranium and copper extraction examples, using the ion-pair and the chelate reagent types respectively, are presented in greater detail to illustrate the more subtle aspects of reagent evaluation and selection. Practical experiences in the laboratory and at some operating plants are a1 so discussed.

Jan 1, 1986

By E. R. Bollinger, N. S. Tanious, R. D. Beckett

The US Bureau of Mines developed hand-made, steel-fiber-reinforced concrete (SFC) blocks for building mine cribs. To ensure wider usage of these cribs, US Steel Mining Co. initiated a joint development and evaluation program with Burrell Construction Co. to mass produce SFC blocks of reasonable dimension, weight, and cost. Small specimens and full-size cribs were evaluated to determine their compressive strength and post failure characteristics. After testing and adjusting of various concrete mixtures, a final formulation was selected that gave a nominal crib strength of 22 MPa (3200 psi) and a nominal modulus of elasticity of 6.9 GPa (1.0 x 106 psi.) These SFC cribs can support 6.4 times as much as a wood crib with the same load-bearing area. The SFC crib was proven to be an economical and effective roof support system through various underground installations.

Jan 1, 1987

By Zong-Xian Zhang, Charlie C. Li

It has been observed that the rock debris of a strain burst event are often in the mode of tensile fracture. Seismic waves could create tensile fractures in the material nearby reflecting surfaces, such as at the boundary of the fracture zone and the rock surface of an underground space. The fractured rock could be ejected to the space when the seismic waves are powerful enough. The average ejection velocity of the ejected rock is a measure of the magnitude of a burst event. The ejection velocity is directly associated with the released energy from the seismic waves and with the strain energy stored in the rock prior to the burst. In some cases, the seismic wave induced tensile fracture and the energy conversion occur in successive moments during bursting. In this paper, tensile fracture caused by seismic waves is investigated through an 1D model. The relationship of the average ejection velocity of the ejected rock in a rockburst event is analytically established with the energy of the seismic waves and the strain energy stored in the rock.

Apr 26, 2022

By R. Wu, R. Howell, J. Dase

Turquoise Ridge is an underground gold mine located in the Potosi Mining District, approximately 64 km northeast of Winnemucca, Nevada. Turquoise Ridge Underground is accessed via two shafts and a system of internal ramps and utilizes underhand drift and fill mining methods with cemented rockfill. The mine also employs mechanical mining as well as sill benching as mining methods. Ground conditions at Turquoise Ridge Underground are poor, and the Rock Mass Rating (RMR) may be less than 20, or very poor, in ore headings. Current production rate is 2,700 tonnes of ore per day. Key challenges in increasing production levels and reducing costs are the development of sufficient stoping areas and the transition from top-cut development to undercut stoping. Completion of the infrastructure development in the North Zone is necessary to achieve and optimize higher production levels. The #3 Shaft project is well underway and is expected to be commissioned in mid. 2022. The shaft will drastically decrease the haulage requirements in the North Zone

Mar 2, 2022

Those who have had an occasion to apply geostatistics to the estimation of ore reserves are familiar with the conventional approaches of estimating average grade of quality values for arrays of regular grid squares or blocks. Further, the technology to perform geostatistical analysis and prediction for irregular two-dimensional areas has been available in a practical, readily useable form for some time. However, the generalization of this technology into three dimensions has been hampered by lack of a suitable geometrical characterization for realistic, three dimensional shapes and volumes. The extension of these estimation techniques into three dimensions has now been made possible by a successful integration of the volume modelling capabilities of 3D Component Modelling with proven 3D Geostatistical Techniques. The result is a powerful new technique for mineral ore reserves estimation in a practical, useable form. The technique allows direct geostatistical estimation of grade and quality values for precisely defined, irregular, realistic, geological, and mining shapes or volumes. This paper describes the two technologies, their integration and their application in practice to the estimation of mineral ore reserves. The paper closes with a discussion of the benefits provided by the new approach, in terms of accuracy, efficiency and practicality.

Jan 1, 1991