Search Documents

By J. Linhart

In vertical airways, falling material - solids-or water - may cause undesirable disturbances in the ventilation in the airway itself and also in neig¬bouring airways unless precautions are taken to stabilize the air flow. Such cases can occur, for example, - in shaft sinking by drilling from a pilot hole, - during the filling up of shafts, and - during the introduction of water into shafts in the case of mine fires. In an airway with upward ventilation the falling material will reduce the air flow and may even re¬verse its direction. In an airway with downward ventilation the air flow can only increase, but a reversal of the direction of ventilation may result in a parallel airway. These disturbances in the normal ventilation are undesirable as it must be the aim to have ventilation that is stable in quantity and direction throughout a mine. In order to be able to prepare suitable stabilization measures one must know the pressure generated by the falling material; this pressure will henceforth be called "aeromotive" pressure. The main factors determining the influence of falling material on the ventilation are - the amount of falling material and its height of fall, - the cross sectional area of the airway, - the pressure. difference prevailing in it, - the-position of the. airway in the ventilation. network, - the air velocity, and - other parameters, e. g. the density and grain size of the falling material. To determine the aeromotive pressure-measurements have been made underground during the sinking and filling of shafts and systematic studies have been carried out during the supply of water into a staple shaft. The present paper deals first with some fundamental theoretical considerations and then describes the measuring arrangements and the results of the series of experiments that have been carried out.

Jan 1, 1980

By Carmine Nappi

This article examines some important trends in East-West trade in non-fuel mineral products, in particular the recent decline in Eastern bloc exports of such products. It relates this decline to an improvement in Soviet terms of trade; a deterioration of geological and locational conditions in Soviet mineral production; an increased integration of the CMEA-countries based on a regional pooling of resources; and a surge in demand for mineral commodities in Eastern countries coupled with a slowdown in Western economic growth. Finally, it evaluates to what extent these determinants may evolve in a different direction during the eighties and thus foster East-West mineral trade. Eastern1 bloc trade in mineral products is a subject of perennial interest in the West. When exports increase, there is much talk of the dangers of dependence on the East for critical fuels and materials. When imports increase, talk turns to the danger of Soviet dependence on Western supplies. A common fear is that the USSR may not only seek to meet its own resource needs but also deny the access of Western countries to these resources. This paper, like three other recent additions to the lite5ature on Soviet foreign trade of commodities2, tries to put matters in clearer and cooler perspective. The first section evaluates the structure of East-West mineral trade and tries to identify some important trends of recent years. The second section relies on supply and demand factors, as well on the Comecon connection (the intra-Council for Mutual Economic Assistance mineral cooperation) to explain why there has been a reversal in the mineral trade trend since the end of the seventies. The last section evaluates the factors which could stimulate East-West mineral trade in the future.

Jan 1, 1986

By Noris Del Be1 Belluz

Drilling underground in the Grasberg dewatering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are used. Pilot holes probe ahead of the tunnel development to intersect aquifers ahead of the face. And dewatering holes dewater rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, static pressures of >8.3 MPa (> 1,200 psi) have been recorded with flows from a 100 mm (4 in.) HQ core hole measured at 5,700 L/min (1,500 gpm). The waterflows can be slightly acidic, necessitating the use of stainless-steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early on to deal with these conditions. PT Freeport Indonesia (PTFI) established procedures to maintain the safety of the drill crews, to enable coring of the rock, and to maintain the safety of the miners driving the drifts. The collar gear controls the waterflows because these drill holes are a vital source of water for the concentrator.

Jan 1, 1998

By Yu. P. Astafyev

The, control of drilling and blasting is a complicated dynamic system whose aim is to ensure safety and prepare rock of required grade and the standard level of broken material reserves Unlike other processes drilling and blasting, as an object have the following features: -a large variety of drilling and blasting methods due to specific conditions of blasting, various types of drilling equipment, schemes-of blasting, types of explosives and others; -relative continuity of drilling, the character of mammoth blasts being discrete; -increased requirements to the safety of blasting;; -a great. number of control parameters, some of them having a qualitative characteristic but not a quantitative one; -availability of feedforward and feedback with other mining processes in terms of time and space. These features predetermine the hierarchical structure of an automated system of planning and control of drilling and blasting (fig.1). The system is implemented on the basis of unity of the data base and in interre lation with other problems of controlling mining operations. An automated system of this kind makes it possible to take optimal decisions actually on all the levels and stages of operations, with rock having been blasted before extraction.

Jan 1, 1986

Stratabound uranium deposits consist generally of two comingled geologic and statistical populations. Barren zones, usually having radiometric assays too low for recording on digitized logs, comprise a large portion of a mineralized stratum. In between are mineralized zones; where the grades are distributed essentially lognormally. Estimation of open-pit ore reserves requires the prediction of the tonnages of selective mining units (the smallest mined volume which may be segregated as ore or waste) and their grades within panels of convenient size for open pit planning and economic analysis. The proportionate tonnage of mineralized selective mining units within each panel can be predicted by kriging an an indicator function assigned to each composite (1 if mineralized, 0 if barren). Next, using logarithms of mineralized assays, the conditional lognormal distribution of grades of mineralized selective mining units can be found. Using this distribution and the krigedestimate of the probability a selective mining unit is mineralized, the grade and tonnage of selective- mining units above any cutoff can be predicted. A case study illustrating this two- step procedure is presented for the Imouraren uranium deposit located in the Republic of Niger. Using cross validation, the estimation procedures were checked and were shown to be adequately accurate for mine planning purposes.

Jan 1, 1979

By R. C. Karra

Mining is one of the oldest profession and second after agriculture. Unfortunately Mining is not so familiar in the society. Due to lack of recognition in the society, existence of mines in remote places and in dusty and humid working conditions, led the poor response for mining engineering. Mining engineering programs have been increasingly less attractive to the student population over the years due to negative image of mining industry. After graduating in mining engineering, there is not much problem of employment at present. In the last 10 to 15years most of the mining engineering graduates have joined software industry. Even those joined in mining industry also left with in 2 years of service. The main reason for this is not being satisfied with job, it is not only working conditions but also work environment, work culture, remote location of the mines etc. Though many were trying to leave mining profession, the recent economic slow down has prompted some of them to incline towards job safety and retained to mining job. At this juncture a systematic study was taken up to analyze the job satisfaction of mining engineers in India.

Jan 1, 2011

By Jair Carlos Koppe, João Felipe C. L. Costa, Luis Eduardo de Souza

United Nations (UN) has been leading an international committee to define the guidelines in reporting resources and reserves. The system proposed by UN is very similar to the guidelines currently in use in Australia known as JORC guidelines (Joint Organisation Reserves Committee). The JORC guidelines show major differences in relation to the Brazilian system current in practice. The important aspects differing JORC from the current Brazilian guidelines for reporting reserves is the required sampling spacing. The JORC system requires the points of observation to be closer spaced than the Brazilian system for any class of resources. All classification systems share some common aspects in terms of defining the classes of resources based on distance separating samples and on the degree of confidence or accuracy associated with the results reported. Despite of being very clear in terms of stating sample distances, all the systems of classification do not provide clear definitions on how confidence limits should be calculated. This paper proposes a geostatistical framework to measure the uncertainty associated with the reported tonnages and grades. Results demonstrate that the error associated with an estimate can be approximated using multiple simulated deposits to define confidence limits. The methodology is illustrated in a large Brazilian coal deposit and proved to be appropriate to address the issue of quantifying the uncertainty necessary to be incorporated in the systems of reserves classification.

Jan 1, 2002

By Craig Ammar

JAMIE DAVIS: Our next speaker is Craig Ammar. He's director of equipment management for Cyprus Climax Metals Company. He has, prior to this assignment, been responsible for maintenance at Bagdad Copper, Cyprus' Miami smelter, and Thompson Creek. Like Jerry, he's very shy and retiring, and doesn't have any strong opinions about maintenance. INTRODUCTION CRAIG AMMAR: The ultimate goal behind implementing a proactive equipment management process is to provide capacity assurance and ultimately increase an organization's ability to generate revenue while reducing operating costs. Targeting such lofty objectives has brought many an organization to its knees, utilizing new maintenance techniques, concepts, and technology aimed at making our lives better and more organized. The root cause of such frustration generally stems from a lack of understanding or support for the fundamentals of implementing a proactive equipment management process. There are just two types of maintenance programs, reactive and proactive. It's an established fact that you need a little of both to run an effective equipment management process, obviously more of one (proactive) than the other. Here are some telltale signs that your equipment management process is in trouble: -Maintenance is performed as a knee jerk reaction when equipment fails. -Repeated and frequent equipment failures occur, with no focus on eliminating the root cause. -Sketchy, inconsistent, unclear preventive maintenance is performed or there is no support for the preventive maintenance process. -No predictive maintenance technology process is in place, or little support for predictive maintenance exists. -Less than 50 percent of your work is generated by the maintenance group resulting from inspections.

Jan 1, 1998

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by the National Institute for Occupational Safety and Health's Pittsburgh Research Laboratory. Investigated were a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal-extraction side of the longwall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. In laboratory experiments and in a longwall field evaluation, the translucent mesh barrier was shown to provide notable dust-control effectiveness for a distance of up to 60 m downstream of the shearer, provided that the mesh barrier remained relatively parallel to the airflow. The staged spray barrier system showed marginal dust-control effectiveness in the laboratory and, therefore, was not field tested.

Jan 1, 2000

By G. A. Rowell, T. M. Barczak, J. C. Zelanko

The US Bureau of Mines conducted a multifaceted geomechanics research project at a bump-prone longwall coal mine in eastern Kentucky. This mine presented a unique opportunity to study coal mine bumps because the problem appeared to be confined to areas beneath a sandstone channel of limited areal extent. The Bureau's research plan sought to exploit the uniqueness of the site by monitoring strata behavior and longwall support reactions as the longwall face approached and passed beneath a sandstone channel. The study incorporated static pillar stress and strata deformation measurements, shield support leg pressure measurements and microseismic monitoring, as well as geologic mapping and the collection of observational data. Data collection was underway when a major coal bump occurred on the longwall face at the mine. Pillar behavior (load and deformation), shield loading and microseismic activity were monitored prior to, during and after the bump. Observations in the tailgate indicated that these pillars were failing prior to and following the face bump. Shield load data, evaluated in an effort to identify trends that could be used to forecast coal bumps, appear to provide a measure of the effectiveness of destressing operations conducted on the face (e.g. shot firing). Analyses of microseismic data revealed anomalous values associated with microseismic "energy" prior to the face bump. In addition, microseismic source-location data and underground observations provided some insight as to the sequence of pillar and face bumps.

Jan 1, 1992

By David J. Kruse

Accurate field measurements are essential when validating a conveyor design. They are fundamental in determining a conveyor's behavior, its long-term maintenance requirements, and the life expectancy/ condition of the installed equipment. Field measurements are also invaluable in forensic engineering, particularly when vital equipment has failed This paper will discuss a wide variety of data acquisition equipment, field measurement techniques and accuracies achieved State-of-the-art, custom designed monitoring equipment, as well as, ''08-the-shely instruments and sensors, will be discussed.

Jan 1, 2004

By J. Siege1, R. S. Popielak

A computer model was used to simulate the effect of leakage through confining beds on a hypothetical in situ leach operation in an aquifer with a thin mineralized section. The simulations were used to assess economic and potential environmental implications of leakage on an in situ leach operation. Four scenarios were modeled - three representing cases with different degrees of confinement, and the fourth representing a stratified ore zone under a low degree of confinement. The model simulated the travel path and travel time of lixiviant given the hydraulic conditions prescribed in each scenario. The results show that the travel path and travel times vary by about 10% for confinement ranging from nearly impermeable (essentially no leakage) to an extremely low level (thin confinement with a permeability about equal to that of the aquifer) for isotropic aquifer conditions. The aquifer thickness contacted by the lixiviant varied from 85% to 90%. Horizontally, 55% to 60% of the aquifer was contacted. The flow paths in the stratified aquifer were reduced in the vertical direction and expanded horizontally. Forty- five percent of the aquifer thickness was contacted vertically with 88% contacted horizontally. Break- through time for lixiviant traveling at mid-depth of the aquifer increased two times when the leakage was increased from nearly zero to a value representative of thin and highly permeable confinement. Leakage affects the economics of in situ mining by (1) increasing the time required to leach out the ore, and (2) increasing the thickness of the ore zone aquifer to be restored. The potential for environmental impacts appears to be minor. In all four simulations, the lixiviant did not contact the confining strata. Restoration would be limited to cleanup of the ore zone aquifer within the thickness contacted by lixiviant and within the radius of the lixiviant that traveled farthest away from the production cell.

Jan 1, 1988

By L. Adler

INTRODUCTION The purpose of this paper is to describe in engineering terms the singular and basic operational kinematics of all excavating and bulk handling equipment. The safe and efficient use of equipment will be fostered by enabling the engineer to conceptually duplicate the operators' "tasks" in directing and controlling it. A simple graphical and notational scheme will be introduced to define the essential gross repetitive motions. The significance of this effort includes filling a vital analytical gap at the work face, and in establishing direct communications between the engineer and equipment operator. Since all types and sizes of earth- moving equipment are covered, a major concern has been to integrate equipment specialties into d single encompassing discipline. Equipment types are closely related to the working conditions, and their selection and evaluation are also considered. The extension to human factors analysis is natural and predictable. Since human [actors are involved, the operational analysis can also be considered a catch-all for many subtle vagaries. BACKGROUND Symbolic modelling linked to a notational system will be developed and intensively used. This constitutes the "language of science," providing a shorthand method which gives immediate recognition, is fluent, explicit, reinforcing, unequivocal and provides limitless associations. Many examples of symbolic modelling exist in chemistry, physics, the military, engineering sciences and it is a major tool in mapping. Its use is so ubiquitous that it often goes unnoticed. On the other hand it must be realized that something is lost in simplifying and idealizing what is an extraordinarily complex occurrence. The components describing the basic operational kinematics of equipment include: (1) the vehicular motions as a rigid body and (2) the job-end motions focussing on excavating (Adler, 1985). These provide all of the components in the load-haul-dump sequence (L-H-D) , and will yield three dimensional expressions. Complex patterns can also be assembled from these simple elements. An existing equipment designation employed in earthmoving will be integrated into this approach (Carson, 1961). Along with the basic motions, corresponding working conditions will be noted.

Jan 1, 1986

By William S. Eaton

Managing a mine or mineral processing operation in today's environment presents many unique challenges to mining companies. In recent years, headlines around the world have publicized major incidents such as those associated with the Marcopper Mine in the Philippines, the cyanide release in Guyana from the Omai gold mine and numerous other mishaps associated with mining. These notable upsets were due to engineered system failures, either during normal operations or as a result of uncontrollable events. There fore, many mining firms are attempting to assess their overall risks and establish some priority for expenditure of limited operational and environmental budgets. Failure of an engineered component can have dire operational consequences that affect profitability until repair or replacement can be completed. In addition, there may be significant environmental consequences associated with the engineered system failure. This, too, may affect profitability for an extended time or even the viability of an operation. An engineered risk assessment (ERA) can support a mining company's efforts to cost effectively manage environmental risks associated with the operation of its facilities. The ERA approach also provides information about the current condition of engineered systems. This ERA approach provides a systematic review of the risks of an engineered system failure and the possible associated environmental consequences at mining company facilities. This approach has been successfully applied to many industries and types of engineered systems (Barneich et al, 1996; Whitman, 1984; Power and Tomkins, 1974; Keeney, Nair, and Kulkarni, 1979). This approach evaluates all mining and mineral processing facilities located at a single site and compares them with similar facilities located at multiple mine sites. The ERA approach has been applied to a mining, milling, smelting, leaching and refining operations. These assessments can be part of a comprehensive environmental program to aid in the recognition and cost effective management of the potential environmental risks associated with the operation of facilities. ERA results support plan-

Jan 1, 1997

By Thierry Coléou

In this paper, we consider open pit optimization. At present, most methods specify the economic parameters and then find the corresponding optimal pit. But as the economic environment varies (which it does regularly these days), the "optimal" pit changes and quite often changes markedly. The questions are: by how much does it change and which parameters are most influential? The functional approach of Technical Parameterization of Reserves, devised by Matheron in 1975, gives the set of all the different optimal pits, under any economic condition. It separates technical design and economic assumptions and thus permits the use of several optimality criteria when choosing the final pit, and not just the maximization of an additive profit formula. Very efficient specific algorithms are presented to obtain all the potentially optimal pits. Fluctuations in the parameters induce changes in the optimum design. Inclusion relations that exist generate very tight bounds and hence very quickly detect optima, even when using a classical adaptation of maximization techniques (graph theory, moving cone, dynamic programming ...). The advantage of Technical Parameterization of Reserves over other methods is that it provides a nested sequence of optimal pits which can then be used for mine scheduling. Many possible mining schedules can be obtained by using the family of technically optimal projects to split up the orebody. The "optimal" schedule, which is in fact a compromise between the different requirements of the economists, the mine planner and the metallurgist, can be chosen from within the wide scope of possibilities. A practical example of mine scheduling for a chromite mine is presented in detail.

Jan 1, 1989

By G. Lodewijks

Today most belt conveyors used for the transportation of bulk solid materials are driven in a centralized way with all drives in one location. The dynamics of these systems has been studied since the early seventies of the previous century and are well understood. Compared to the more conventional belt conveyor system with a centralized drive station positioned at the head and/or tail of the system, a decentralized driven layout with drive stations distributed along the whole length of the belt offers a number of advantages. However, to make a decentralized driven configuration a good alternative to a centralized driven, the system designer will have to balance these benefits with the increased complexity. The full potential of a decentralized driven system can only be realized if the right balance is found between the locally applied drive force and the motion resistances occurring along the system. From previous research it was found that in a multiple driven belt conveyor system the most dominant belt behavior occurs in the belt section between the tensioning device and the first drive station. In this paper different possibilities are analyzed to improve this dominant belt response and optimize the starting behavior. This can be accomplished by changing the predescribed start up profile, starting the drive stations in sequence rather then all at the same time and altering the locations of the drive stations.

Jan 1, 2008

By Jennifer B. Leinart

With the signing of the North American Free Trade Agreement (NAFTA), Canada, the United States and Mexico entered into an international experiment in economics amid a cloud of controversy that still lingers. Central to the controversy are the disparities in wages that exist among workers in the signing countries. Wage surveys completed by Western Mine Engineering show the degree of disparity that exists among the mining industries of those three countries. Labor costs constitute 30% to 50% of operating costs. So these wage differences are a matter of interest to the mining industry. It is unclear how much of a factor they are in determining where companies search for and develop new mines. That depends on where minable deposits are expected to be found. However, a deposit that may not be minable in the United States or Canada may be minable in Mexico because of lower labor costs. Some adjustments are anticipated for the Mexican mining industry if and when its wages begin to approach comparability with US and Canadian wages. Table 1 combines the results of four recent surveys. It lists benchmark wages for mining job titles common to all the countries. About 220 mines are covered by the combined surveys. Canadian miners' wages, converted to US dollars, are typically 75% to 95% of US wages, while Mexican miners' wages are less than 10% of those in the United States. Table 1 also shows that wage disparities are not confined to international borders. In fact, the difference in average wages between the US coal industry and the US metal and industrial mineral industries is greater than between the Canadian and the US mining industries overall. Table 2 shows that managerial, technical and administrative salaries show similar, but less pronounced differences among the three countries. Salaried personnel at Canadian mines earn 80% to 90% as much as their US counterparts, while those in Mexico earn 20% to 30% as much. Here again, average US coal salaries exceed average salaries for the US metal and industrial mineral industries.

Jan 1, 1998

By Bryce T. Tripp

Utah's abundant industrial rock-and-mineral resources support a relatively small but important sector of the State's economy. In 1983, six of the top 10 nonfuel mineral commodities (by value) were industrial commodities. Portland cement was ranked fourth, potash fifth, halite sixth, phosphate seventh, construction sand and gravel eighth, and lime tenth. Portland cement was produced by three operators, principally from the Jurassic Twin Creek Limestone. Potash was produced by three companies from Pennsylvanian beds in the Paradox Basin, surface brine of the Great Salt Lake, and subsurface brines of the Great Salt Lake Desert. Halite was produced by eight operators, primarily from surface brine of the Great Salt Lake. Additional production came from salt beds in the Jurassic Arapien Shale, solution mining of the Pennsylvanian Paradox Formation of the Hermosa Group, and subsurface brines of the Paradox Basin. Phosphate was mined by one company from the Permian Meade Peak Phosphatic Shale Member of the Park City Formation. Construction sand and gravel were produced by dozens of operators, primarily from Quaternary Lake Bonneville beach and nearshore deposits. Lime was produced by four operators from Paleozoic formations in the Basin and Range physiographic province of Utah. The future production of these and other industrial commodities, though individually uncertain, is expected to increase gradually as a group. Factors favorable for the future of the industrial commodities industry in Utah include large to almost unlimited resources for the major commodities, a healthy projected population growth, an abundant local supply of relatively inexpensive energy from coal and natural gas, and a favorable corporate tax structure and business climate.

Jan 1, 1987

By Graham Swan, Richard K. Brummer

The paper begins by describing an underhand cut-and-fill mining concept for a 50m thick, generally tabular though irregularly shaped orebody dipping at 30 degrees and occurring at a depth of between 2300 and 2700m in the Sudbury Basin. From this, the broad design requirements of a fill system are stated. Two and three-dimensional numerical models are then described which were built to evaluate the theoretical benefits of different types of fill reinforcement. Included in this evaluation are the effects of span, fill strength, fill tightness, as well as static and dynamic loading types. Results, supported by large-scale physical models, are presented to show the significance of reinforcement on stable, undermined fill performance. Finally the paper describes work which has been done to evaluate the suitability of so-called silicated cemented backfill. This system is, in principal, attractive for deep mining applications since transportation is in the "safe" hydraulic regime, while fill water run-off, segregation and shrinkage effects are potentially eliminated in the stopes. The results from various surface and underground trial pours are reported which substantiate the proposed use of this type of backfill at depth.

Jan 1, 2001

By A. R. Wagner, E. Berkman

The use of high-resolution seismic surveys in coal exploration and mine development is becoming established as a standard technique in the industry. Their most significant contribution is in the effectiveness of reducing the number of core holes needed to understand the complex geological nature of coal by identifying geologic faults and mapping coal seam continuity and relative coal thickness. With these goals in mind, a high-resolution seismic survey was conducted in 1980 in the Wasatch Plateau coalfield of Utah. As a result of the success of this initial survey, numerous additional surveys have been performed over the past six years.. The interpretations of these subsequent surveys have led to the location of faults, fluvial channel sandstones, and coal thickness trends. This paper presents a review of high-resolution seismic technology as applied to coal exploration followed by three case histories, two of which illustrate the utility of the technique related to coal thickness determination and faulting and one that serves as an example of pitfalls in interpretation.

Jan 1, 1987