Search Documents

By G. S. Adisoma, J. J. K. Daemen, R. O. Roko

A common assumption in determining the shear strength of a rock joint using a direct shear test is that the surfaces undergoing relative shear are in complete contact. Furthermore, the limiting displacement associated with the residual strength values is obtained based on engineering judgement through visual inspection of shear force versus displacement curves. This study proposes a systematic way of determining the residual shear strength of rock joints by evaluating the limiting displacement leading to a minimum cohesive strength value and taking the true area of contact into account. The results of the study indicate that there is a limiting displacement associated with the residual shear strength, and some rocks may have an inherent interface residual cohesive strength different from zero. When the cohesion is different from zero, the residual shear strength is likely to be underestimated if the true area of contact is not considered. In the case where zero calculated cohesion is obtained, the area of contact has no bearing on the shear strength equation because the frictional force depends only on the normal load.

Jan 1, 1986

By J. C. Watts

Ball mill grinding circuit control has received increasing emphasis in the past few years due to such factors as declining ore grades, increasing production costs, and advances in analytical devices and minicomputer technology. Since ball mill circuits have been a traditional bottleneck in mineral processing plant throughput, control systems often improve through- put without requiring additional processing equipment. In addition, much of the variability of the grinding product size and consistency is often removed, allowing better process operation downstream. Among the problems which arise in designing and implementing a process control strategy for ball mill circuits are circuit constraints imposed by processing equipment and local management, proper instrument selection, installation and maintenance, and use of calculated or inferred variables for process measurements. This paper discusses these problems and attempts to identify valid approaches to their solution.

Jan 1, 1979

By L. Vandamme, J. H. Curran

A fully three-dimensional hydraulic fracture propagation model, based on the Displacement Discontinuity Technique, is briefly described. Using this model, it is shown that the geometry of a propagating fracture is dependent on several factors, among which the fluid pressure distribution within the fracture plays an important role. The containment of hydraulic fractures is found to be dependent on stress and toughness barriers in the formation. Containment is also observed to be more effective with a decrease of the viscosity, pressure or flow rate of the injected fluid. The three-dimensional layout of the fracture is shown to have a definite influence on the width and pressure distributions within the fracture. The examples considered indicate the need for fully three-dimensional models, as complements to the commonly used two-dimensional and pseudo-three-dimensional models.

Jan 1, 1986

By G. D. Schena

A decision support system for the management of the mineral resources of a developing country has been derived. The system allows the evaluation of the impact of a mineral project in a developing country in the broad context of its economy. The analysis permits the assessment of the overall socio-economic consequences of mineral prospects and allows incorporation in the evaluation of issues that are broader in scope than the pure financial objectives. The system is built around the Leontief framework of economic analysis. The original input-output model, enhanced to incorporate country-specific behaviour is integrated with cost-benefit analysis and shadow pricing. The analysis leads to synthetic measures of profitability at market and shadow prices. These measures are useful to direct the mineral policy of a developing country through the exploitation of those mineral resources which are most likely to bring about economic growth and social advancement.

Jan 1, 1992

By M. H. Pelkki, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Research has shown that excessive soil compaction is detrimental to the establishment of trees in reclaimed soils. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed soils. It is believed that reclamation practices that minimize soil compaction will produce better results when forestland is the intended postmining use. The University of Kentucky has developed reforestation test cells on reclaimed soils at a surface mine in eastern Kentucky to test this hypothesis. Each test cell has been planted with various species of trees. Since 1997, data have been collected at these test cells for soil average dry bulk density, average penetration resistance, average depth to refusal and average survival rate of trees. These data have been correlated to determine the relationship between soil compaction and tree-survival rate. It is believed that these two soil-compaction parameters may ultimately be used to predict tree-survival rates on reclaimed surface mined lands.

Jan 1, 2003

By Fernando de Oliveira Durão

A complete computer package for the steady-state simulation, either in analysis or in design mode, of mineral processing flowsheets is described. The main features of the simulation package are: modular architecture, flexible structure and sequential solution strategy. Different detail levels of mathematical models of several mineral processing unit operations have been developed and implemented as unit modules (FORTRAN routines). Unit operations currently modelled are: coarse/fine crushing, grinding, screening, hydrocyclone classification, gravity separation, heavy media separation, froth flotation, high gradient magnetic separation and solid-liquid separation. In design mode, a simulation study is stated as a general non linear optimization problem. The objective function is a weighted sum of square deviations between the design specification set points and the calculated values, subject to non linear equality and inequality constraints. The optimization problem solution is obtained solving successive Quadratic Programming subproblems followed by inexact line search of an exact penalty function (Powell algorithm). One non trivial example is discussed, illustrating the design capabilities of the simulation package.

Jan 1, 1992

By Johannes Wageneder

As a reaction to the fire accidents in tunnels in Europe Designers nowadays have to demonstrate the integrity of underground structures such as metro systems, railway and road tunnels in case of fire load wherever as a consequence of a lining collapse surface infrastructures or residential areas could be affected. To respond to this FLAMDOCS allows to calculate the stability of reinforced concrete structures during fire load for a series of prede?ned time steps. Elementary theories of non linear material properties and reinforced concrete structures are used.

Jan 1, 2003

By David J. Maguire, Ken Alexander, Maya Scherbakov

As conveyor systems continue to improve in reliability due to improved design, installation, maintenance, and operation, one of the more common modes of failure is the rubber carry cover being abraded away to the tension member. Various types of abrasion are discussed as well as current laboratory methods for measuring wear. New lab methods to mimic types of abrasion in service are presented and data from current and improved rubber covers will be presented. Actual wear performance of current and new cover compounds in multiple applications (coal, limestone, granite) will be compared to the new lab test methods and cost benefits shown.

Jan 1, 2002

By Daniel McConvey

Who is the Investor? -Mainly institutional, including resource funds, other mutual funds and pension funds. -Some hedge funds. -Retail investors. -How important is the reserve disclosure to these investors? -Do these investors know the difference between a reserve and a resource?

Jan 1, 2003

By Paul Clifford

The Florida Institute of Phosphate Research (FIPR) is an independent, state of Florida research agency. It was created in 1978 to conduct research to enhance the competitiveness of the Florida phosphate industry. The institute also conducts research to prevent, minimize or rectify environmental impacts caused by the industry. And it helps educate the public concerning phosphate-related technology and issues. FIPR is funded by a severance tax on the industry and is governed by a five-member board of directors appointed by the governor. FIPR's research is playing a role in enhancing the competitiveness of the Florida phosphate industry. Its technology research program seeks to improve surface mining and pipeline transportation while reducing the energy cost for pumping phosphate matrix. It is developing new and improved methods of beneficiation and fertilizer production. This includes new process flowsheets and on-line analyzers and process control methods. FIPR is also developing uses for the phosphogypsum byproduct of phosphoric acid production and evaluating the risks associated with its uses.

Jan 1, 1998

By H. C. Verakis, T. E. Lobb

During the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry, with coalmining being the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past several decades. Although blasting accidents usually represent a small percentage of the total number of mining accidents, they continue to occur and the severity of these accidents is disproportionately high compared to the other mining accidents. This paper is an analysis and summary of mine blasting accidents over the past several decades as they relate to surface coal mine operations. A compilation and review of surface mine blasting accidents from1978 through 2001 was made. The accident data was examined to identify the trends and primary causes, which continue to be blast area security, fly rock, premature blast, and misfires. Approximately 46percent of the causes of surface coal mine blasting accidents are attributed to blast area security, while fly rock, premature blast, and misfires represented an additional 50 percent of the causes. Accident categories were established based on the cause of the accident or the activity that was taking place when the accident happened. A discussion of the accident data is presented to increase hazard awareness and to emphasize safe blasting practices and MSHA requirements concerning mine blasting operations.

Jan 1, 2003

By Jean-Michel M. Rendu

According to statistical theory, the geostatistical methods of ore reserves estimation are greatly superior to any other method. However acceptance of geostatistics by the mining industry has been slow and not as wide spread as one would expect. One of the reasons for this cautious approach is that it is often questioned whether the geo- statistical assumptions are satisfied in real world situations. When blocks of ore are estimated in a mineral deposit, geostatistical theory can be used to determine which method of estimation should give the best results. Using this theory, the relationship between estimated value and true block value can be quantified. There is a need to verify that this theoretical relationship is actually observed in practice, and that the block estimates ' obtained using the theoretical ly best method of estimation, are actually most similar to the true block values. In this paper the results expected according to the theory are compared with the results actually obtained. Sample values from a large bedded gold deposit have been used. Blocks of ore have been estimated by a number of methods, including the polygone, inverse power of the distance, kriging, logarithmic kriging and other geostatistical methods. The block estimates have been calculated from samples on a large grid, and compared with the true block values obtained from additional samples on a much smaller grid. The results of this comparison show extremely good agreement between theory and actual results.

Jan 1, 1979

By D. J. Kennedy, A. W. Stokes, W. G. Klinowski

Sulphur hexafluoride (SF6) has become an accepted standard in the field of mine ventilation tracer gas studies. It has a wide variety of uses for defining mine ventilation flows that cannot be adequately described using conventional instruments such as anemometers and smoke tubes. The Cape Breton Coal Research Laboratory (CBCRL), Energy, Mines and Resources Canada, has been using SF for the past 4 years and has developed numerous release and sampling systems to increase its versatility. The CBCRL has also completed a successful field trial of an automated rapid sequential SF6 analyzer (which gives a pseudo real-time readout) that can be used underground. In doing this work, the authors recognised the potential of being able to use more than one tracer gas simultaneously in an underground study. Two alternative tracer gases (Freon-13B1 and Freon-12) have already been used by CBCRL in some of their underground work. These gases can be measured by gas chromatography utilising an electron capture detector in a similar manner to SF6. A description of these gases, the methods for 6' their handling, release and sampling are given in this paper together with a brief outline of the analytical system used to measure them. Their suitability to mining applications is compared with SF6. A study in which these three gases were used together is discussed and the results and conclusions given. Some of the additional uses for multiple tracer gases to assist the mine ventilation engineer in resolving problems and improving his day-to-day monitoring are discussed. Finally, a brief analysis of developments which can be expected in the near future is outlined.

Jan 1, 1987

By Jesse L. . Jr. You

Tunnels in the granitic Climax stock at the Nevada Test Site were inspected for keyblock occurrence. Thirteen relatively large pyramidal keyblocks were located in about 230 m (750 it) of tunnel. Orientations, dimensions, joint roughness coefficients, and joint compressive strengths were measured for the faces of nine keyblocks. The measurements were used to back-analyze keyblock stability to check the validity of a numerical model for keyblock behavior. A newly developed three-dimensional numerical model correctly predicted whether or not each keyblock failed in six of eight cases. The two exceptions involved stress conditions and keyblock locations that clearly violated the assumptions that underlie the stability model. The observations also allowed the effect of tunnel orientation on keyblock occurrence to be evaluated. Of the thirteen observed keyblocks, nine large blocks were found in less than 30 m (100 ft) of the Piledriver drift (which runs N56E) while only four blocks of comparable size were observed in 200 m (656 ft) of the Spent Fuel Test--Climax drifts (N61W). The orientations of the keyblock faces were checked against known discontinuity set orientations; some of the faces correlated well with mean set orientations, whi.le other faces were fringe members of sets. Stereographic techniques were used to examine the frequency of keyblock occurrence and to determine the maximum keyblock size that could be encountered with a given combination of discontinuities. Keyblock occurrence was found to be affected by tunnel orientation in a predictable way; this can be used to guide or improve tunnel design practices.

Jan 1, 1986

By J. W. Shuster

Test of trolley-diesel prime power is another step in the search to exploit the unused potential of electric wheel driven haulage trucks. The output of the present engine - a 700 horsepower diesel - is not adequate to exploit fully the 1200 horsepower potential of the two electric wheel drive motors. Power was supplied to a modified 100-ton haulage truck through a double wire trolley system. The vehicle was tested with various payloads on a 7% adverse grade haul road. More significant conclusions developed are: Power - Horsepower to propel the vehicle can he more than doubled to improve truck cycle time. Productivity - Trolley power up adverse grades can improve [producivity] rates from 18 to 36%, dependent upon haul road profile.

Jan 1, 1968

By L. R. Stoiser

The mineral resource potential of the Los Bronces deposit was successfully evaluated by an intense, coordinated field program over a 37-month period (April 1978 - May 1981). This project was part of a much larger study to determine the economic feasibility of expanding the open-pit, mine-mill operation 10-fold to 80 kt/d (88,000 stpd). The resource project included more than 120 km (74 miles) of core drilling and 64 km (40 miles) of drill rig access way construction under adverse topographic and climatic conditions, detailed geological mapping, and other related activities. The Los Bronces deposit is composed of an earlier mineralized porphyry-type body intruded in part by a large complex of mineralized hydrothermal breccia pipes. The mineralization is hosted by intrusive and extrusive igneous rocks. Various stages of erosion, oxidation, leaching, and supergene enrichment of copper are present. Drill hole indicated geologic reserves are estimated at 1.3 Gt (1.4 billion st), averaging 0.81% copper and 0.016% molybdenum at a cutoff grade of 0.6% copper equivalence decreasing to 0.25% over the life of the mine. Trace amounts of silver are also present.

Jan 1, 1987

By D. Robert Weir

The pioneers in pressure hydrometallurgy have provided a solid foundation during the past four decades. The pressure techniques are now capable of being used to push back the frontiers in the winning of metals. Pressure hydrometallurgy has been used to meet the objectives of extracting metals; purifying metal solutions, recovering metals; and rendering waste streams acceptable for disposal to waste repositories and the environment. Some examples of each of these functions are briefly reviewed. The applicability of pressure techniques to the recovery of precious metals is discussed.

Jan 1, 1985

By A. J. P. Durham

Two low water flux test covers were placed on acid generating waste rack dumps at the Kidston Gold Mine in Queensland, Australia The climate is semi arid with distinct wet/dry seasons. The present study was initiated to develop a cover system to restrict infiltration. The design of the cover required optimization of water storage and evapotranspiration. Instrumentation was installed on both dumps to measure infiltration, moisture conditions and climatic parameters. Field measurements over the last three years indicate that both covers are performing satisfactorily. Selection of the final cover for closure is described on the basis of these results.

Jan 1, 2000

By Ted H. Eyde

Specialty sand and bentonite are produced in the plateau province from the Bidahochi Formation near Sanders, Apache County, Arizona. It appears that deposits of both sand and bentonite formed during the Pliocene in fluvial and lacustrine environments, respectively, along the west side of the Defiance Uplift. The bentonite is an alteration product of airborne vitric ash that fell or was washed into lakes. In the Cheto district, the individual bentonite horizons, which range from less than a foot to more than 10 feet thick, are restricted to the position of the medial volcanic member. Bentonite production began at the Allentown mine in 1924 and the Chambers mine in 1926. In 1933 strip mining of the extensive deposits in the Cheto district commenced. Production increased each year to a peak of 270,000 tons in 1957. As a result of the introduction of synthetic zeolites into petroleum refining, production declined. About 40,000 tons of bentonite are currently produced from the district each year. Bentonite is shipped out of State for processing into desiccants, thickeners, and acid-activated clay products. The specialty sand was derived from Permian sandstones and deposited by streams draining the Defiance Uplift. Although stream channels are usually restricted to the upper member of the Bidahochi, stratigraphically above the bentonite horizon, a few actually cut through the bentonite. The well-sorted sand, suitable for use as a proppant in hydraulically fractured oil and gas wells, is localized in elongate lenses along the margins of the channels. These lenses range from 5 to 50 feet in thickness and often extend thousands of feet in both width and length. The sand is about 97 percent silica, has a yield of 40 percent in the minus 20 plus 40 mesh size fraction, and has a roundness of 0.6 to 0.7 on the Krumbein scale. Production of this sand began about 1961. All of the current production, which amounts to about 40,000 tons per year, is sold in the petroleum-producing area near Farmington, New Mexico.

Jan 1, 1987

By David Morrison

On the Corramandel Peninsula of New Zealand, the Waihi Gold Mine has undergone a major redevelopment. The upgrade included the construction of two very large overland belt conveyors, both rated for a capacity of 6000tph. The first of these conveyors (CVR2) traverses a total of 1600m over undulating terrain, including a significant section running through tunnels. A large hill is climbed, just after the mid-section of the conveyor run, before dropping back down prior the discharge point. The second of these conveyors (CVR8) traverses 1100m along an alignment with a horizontal curve, a number of vertical curves and a significant lift before the discharge point. The CVR8 conveyor also included a shuttling head pulley arrangement. The mine they service is inside the town of Waihi. The conveyor alignment runs through the town and out to the metallurgical process site on the outskirts of the municipal area. This paper documents the engineering process that took place in the design of these conveyors. The Martha Hill mine in Waihi, New Zealand is unique. The mine is placed in the township. Consequently there are quite stringent environmental limitations on the mine's operation. In [Figure 1] the proximity of the mine to the town is shown. In the top-centre of the photograph the alignment of the existing smaller overland conveyor can be seen leading from the mine to a tunnel through the hill in the background.

Jan 1, 2000