Search Documents

By C. Kliem

Geological, tectonic, geochemical and geophysical data were utilized for the mineral resource assessment of the Biga Peninsula in NW Turkey. During the deductive phase of the project multivariate statistical methods were applied to accentuate characteristic parameters which sufficiently describe the different types of Pb - Zn mineralization. The parameters most likely to be indicative of mineral occurrences were determined. In the following prognostic phase these parameters were further statistically treated to determine favourability indexes for the occurrence of a deposit within each cell of the training area. Preliminary results of probabilistic, univariate and multivariate methods are presented.

Jan 1, 1987

By K. R. Johnson

Changes in the pattern of computer systems for mine planning and geologic evaluation are occurring as a consequence of the introduction of 3-D high performance graphics terminals. The VULCAN system is described and an outline of its functionality is discussed. Increasingly, the integration of both database systems and graphics and databases will occur, allowing a greater degree of information access to mine operators. The system covers areas of database, drillhole graphics, mine design and layout, surface and solid modelling as well as reserve inventory generation. The design of the software is such that it is fairly commodity-independent and entirely menu-driven, to enable non computer-trained personnel easily to access the system.

Jan 1, 1987

Stochastic methods are normally invoked / used to assist with the understanding of risks, when there is uncertainty around a particular outcome. Uncertainty implies that there is a risk that the desired outcome will not be realized. Stochastics and probability theory has long held out the promise to answering this need, but has often been maligned because of its misuse. This paper takes a critical look need for Monte Carlo simulation to project risk evaluation and highlights what is considered to be the fundamental issues that should be thoughtfully considered to avoid the abuse of this technique. The upside of avoiding the abuse of this technique will be the wider acceptance by practitioners that it is a credible technique to quantify this important aspect of valuation.

Jan 1, 2007

By J. O. Claassen

A study was initiated and solutions implemented to address the root causes of a 30%?40% lower than predicted product yield achieved at a Mpumalanga coal mine. A holistic MRTM approach, which focused on improving exploration, geological sampling and analysis, geological modelling, planning, mining, and beneficiation practices, was used. The study indicated that deviations in the planned versus actual yields at the DMS plant were caused mainly by incorrect geological yield predictions, high and variable levels of dilution, and near-dense material, as well as the textural properties of the ore. Keywords MRTM, mining value chain improvement, Witbank coalfields, complex geology.

Oct 1, 2013

By A. P. I. Popoola

Aluminium AA1200 was laser alloyed with a combination of nickel and titanium diboride using different weight ratios. Chemical reactions took place with the formation of different phases. The characterization of the alloyed surfaces was carried out by x-ray diffraction (XRD), optical and scanning electron microscopes. The alloyed surfaces are composed of the initial phase of Al-Ni dendrites and eutectics of TiB2/Al and TiB2/Ni distributed on the initial phase. Experimental results obtained showed that Al-Ni intermetallics brought about a significant increase in the hardness property of Al; however, these intermetallics are highly brittle and prone to fail by brittle fracture or stress corrosion cracking when put in service. The addition of TiB2 brought about a reduction in the formation of the seintermetallic phases. A microhardness increase of over 10 times the hardness of the substrate was achieved. Keywords Dendrites, intermetallics, metal composite, Nd: YAG laser.

Jan 1, 2011

By M. Mabuza

Two Rivers Platinum Mine (TRP) is a 55:45 joint venture between African Rainbow Minerals and Impala Platinum, respectively. TRP is situated on the farm Dwarsrivier 372KT, in the southernsector of the eastern limb of the Bushveld Complex. Dwarsrivier is underlain by rock formations of the Critical Zone (Winterveld norite-anorthosite) and the Main Zone (Winnarshoek norite-anorthosite). Two economically significant PGE-bearing layers namely the Merensky Reef and the UG2chromitite are found within the upper Critical Zone. These are approximately 140 m vertically apart, separated by a series of barren norites and anorthosites. At Two Rivers Platinum, only theUG2 chromitite layer is currently being mined for PGEs. The UG2 sub-outcrops north/south along the Klein Dwarsrivier river valley with a very gentle dip to the west of 7º?10º. At Two Rivers the UG2 averages about 120 cm in thickness, overlain by a waste pyroxenite parting about 20 cm thick, above which is a leader seam about 20 cm in thickness. The mineable cut consists of the leader seam, the waste pyroxenite parting, the UG2chromitite layer including 25 cm of pegmatoidal pyroxenite footwall, below the UG2 reef to a minimum of 185 cm trackless mining cut. The mining method is a mechanized bord and pillar layout, which will yield a total of 185 000tons at full run of mine production from the underground UG2 mine.

Jan 1, 2006

By R. Venter

Uranium in the tetravalent state has very low solubility in acid and alkaline solutions and needs to be oxidized to the hexavalent state to become soluble. In acid leaching of uranium the uranium is oxidized by ferric iron, which in turn is reduced to ferrous iron. The reduced iron needs to be oxidized to the ferric form to allow the uranium dissolution reaction to proceed. This paper considers the known and proven oxidants used in acid leaching of uranium. These include manganese dioxide, sodium chlorate, hydrogen peroxide, ferric iron, oxygen and sulphur dioxide/air (oxygen). The reaction chemistry of each oxidant as well as the practical applications are considered and discussed. All the oxidants discussed work adequately in acid leaching of uranium and it is possible to engineer solutions for the use of the oxidants in acid leaching on plant scale. The availability and supply of the oxidant as well as the cost and environmental impact of the oxidant plays a major role in the selection of a suitable oxidant. The location of the plant will also have an impact on these issues.

Jan 1, 2009

By R. L. Castro

Currently, in several caving operations, the spacing between the drawpoints is determined by consulting Laubscher's design guide (Laubscher 1994, 2000), a methodology based on the gravity flow characteristics of the caved rock. Laubscher's methodology is based upon the height of interaction between adjacent flow zones, but does not allow calculation of primary recovery for a given layout. In this paper the authors present a technical and economic methodology based on the flow that occurs near the drawpoint and the associated development costs to estimate the optimal spacing. The flow model at the drawpoint was validated at the El Teniente mine, which extracts coarse caved rock. To validate the flow model, small-scale simulations using drawpoint clusters were conducted and results compared to extracted grades, marker recovery, and drill holes to determine ore remnants that are part of the production control programme at the mine. The results indicate that primary recovery depends on the height of interaction, which varies with the friction angle of the caved rock and the spacing between adjacent drawpoints. Primary recovery estimations indicate values from 85 per cent to 97 per cent depending on the drawpoint spacing used. Extrapolations were then conducted to estimate the primary recovery for different drawpoint configurations planned to be used in the New Mine Level of the mine. The results indicate that the optimal drawpoint spacing is 32 m x 20 m with a through length of 18 m. The methodology developed may be used to estimate optimal drawpoint spacing for block caving mines under different metal prices and mine cost conditions.

Jan 1, 2012

By O. Tshifungat, A. Luzanga, N. Goel, S. Sandoval

"Tenke Fungurume Mining Company (TFM), located in Katanga Province, Democratic Republic of Congo (DRC), began production of copper cathode and cobalt hydroxide in March 2009. Copper production capacity was 115 000 t/a utilizing a semi-autogenous grinding, agitated leach, countercurrent decantation process followed by solvent extraction and electrowinning (SX-EW). Cobalt production capacity (as cobalt hydroxide) was 8000 t/a utilizing a three-stage purification/precipitation process treating raffinate from the copper SX-EW process. Recently a phase II expansion was completed, in which copper electrowinning capacity was doubled and four stages were added to the SX plant. Corresponding enhancements were made to mining, milling, and processing to bring production to 195 kt/a copper and 15 kt/a cobalt. An additional sulphuric acid plant is currently being constructed, adding 1400 t/d sulphuric acid to bring total acid production to 2250 t/d for use in leaching at TFM.Initial copper electrowinning results were satisfactory, but cathode quality and current efficiency decreased as copper production increased. The Freeport-McMoRan (FCX) Technology Centre and TFM personnel began operation of two bench-scale copper electrowinning cells in the tankhouse to diagnose chemistry effects on the cathode and anode. The results indicated an excellent electrolyte chemistry, producing finely crystalline copper at 430 A/m2 current density with 98% current efficiency. Attention next turned to the physical factors of the electrowinning cells, including electrode insulator geometry and performance. A demonstration cell was selected in the tankhouse and was operated with varying cathode and anode insulator geometries. Operation of the demonstration cell with a three-side cathode edge strip, A-style anode insulators, and an improved cell furniture design increased current efficiency from 77% to 89% at 400 A/m2 current density. Cathode quality improved correspondingly. TFM is now operating at 92% current efficiency."

Jan 1, 2016

Bougainville Copper Limited (BCL) operates a 50 Mtpy copper/gold/silver mine and concentrator on Bougainville Island, Papua New Guinea. BCL has installed an in-house developed data logging and supervisory process control system using a DEC PDP 11/73 mini-computer in the mill and has recently installed a similar system in the crushing plant. Together with the central DEC VAX 11/780 computer, they form part of a high speed, fibre optic, local area network in the concentrator. The in-house developed software, known as BIAS (Bougainville Copper Information and Automation System), was developed as a low cost option to interface to a number of different existing plant input/output systems while providing the capability to make maximum use of computer networking facilities. The package includes the more usual control system colour displays and data logging features, but also makes provision for two novel features: (a) Any user connected to the computer network can access the system displays. This allows metallurgists and management to monitor (but not control) plant operation from their offices. (b) Specialized application programs for performing advisory and supervisory control, dynamic simulation, and data analysis are easily incorporated into the system. The mill process system currently runs rougher/scavenger flotation stabilizing control and general data logging. The crushing plant system currently performs data logging only; however it will soon be augmented with the facility to run dynamic crushing plant simulations. Future developments will concentrate on making greater use of the detailed information available from the mine's fully automatic truck dispatch system which runs on a VAX 11/780 computer. Milling process control will be expanded to examine possible economic control of the operation of regrind and cleaner flotation circuits. An advisory water management system to optimize water supply within powerhouse generating capacity constraint will also be investigated.

Jan 1, 1987

By N. K. Singh

The calculation of resource volumes for large mineral sands deposits is the process of systematically compiling all known data in order to define the volume of ore contained and its intrinsic economic value. Traditionally, this process has been highly speculative in nature, as the variability of the layer thickness, even between closely spaced, boreholes can be highly variable. The issue of horizon continuity is of critical importance in mine modelling and resource definition. Accurate volume estimates are difficult to derive from drilling data alone, as the borehole spacing of an economically viable drilling programme is often greater than the spatial frequency of the variations in profile thickness. The limitations associated with this inferential approach to resource estimation can be mitigated through the use of newly developed ground penetrating radar (GPR) methods, thereby maximizing orebody optimization by reducing contamination and orebody loss. The use of GPR in the mining industry has historically been limited to shallow, high-resolution applications, such as the location of voids in limestone or the mapping of paleo channels for alluvial gold and diamonds (Francke and Yelf, 2003). These limitations have not been technology based, but rather market based, as the vast majority of GPR systems were originally designed for civil engineering applications. A new generation of GPR technology, designed specifically for maximum penetration in sand environments, is now being developed. This technology has been trialled extensively at the Richards Bay Minerals heavy mineral sand deposit in South Africa with optimistic results. The clay base of the mineral sands has been imaged to some 120 metres. Further equipment refinements are expected to yield even deeper profiling and higher resolution. The resolution offered by this technology is unique, allowing individual depositional sequences to be imaged and modelled in three dimensions. This paper will discuss the advances in GPR technology relevant to the mineral sands industry, as well as methods to optimize and integrate GPR data into existing mine models. Also addressed will be approaches to three-dimensional modelling of high-resolution GPR data and subsequent volume estimations.

Jan 1, 2007

By Z-P. Song, Z-B. Jiang, A-N. Jiang

"In deep excavations under conditions of high ground stress, even hard rock undergoes creep and other time-dependent effects that may result in instability. This study involves an analysis of the typical damage to the surrounding rock in the deep tunnels of the Jinchuan nickel mine in China. In order to understand the creep mechanism, triaxial creep laboratory tests were conducted under high stress. The creep characteristic curves and the Nishihara model parameters of typical rock were obtained from these tests. The numerical simulations, with which the creep model is developed, were performed using Flac3D. The creep model parameters were back-analysed on the basis of field monitoring data. Finally, appropriate support schemes for deep tunnels are suggested. The creep deformation of rock increases with time and axial load. At the same load level, the creep deformation of unloading is greater than that of loading. The simulated deformations of the surrounding rock are coincident with those from in situ monitoring, indicating the applicability of the presented rock creep model in situations of high ground stress. The results constitute a reference for support design in deep mining tunnels.IntroductionThe excavation of underground caverns can alter the natural stress field of the surrounding rock. In deep engineering projects under conditions of high ground stress, even hard rock shows obvious creep properties and time effects (Yao, 2005; Liu, 1994). The time effect of excavation not only causes decompression of the floor and increases sidewall stress, but also leads to stress concentration at the corners of the excavation, which influences the stability of the surrounding rock in a very complex manner.Many researchers have studied the creep properties of rock. ‘Griggs (1939) showed that creep occurs in sandstone, shale, and silty sandstone rock under the load of 12.5%–80% of the failure load.’ Subsequently, much research has been published on rock creep tests, including the uniaxial compressive creep test, the triaxial compressive creep test, the discontinuity rock shearing test, and field tests (Wawersik, 1974; Amadei et al., 1980; Okubo et al., 1991; Jin et al.,1995). A rheological model is used to describe the complex rheological deformation of material. This model is based on various fundamental parameters including rock elasticity, plasticity, and viscous properties, which can be combined into a constitutive model to reflect the rheological properties of various types of rocks. Wang et al. (2014) studied the creep– damage–rupture characteristics of rock salt by applying a creep-damage model. Munson (1997) developed a multi-mechanism constitutive model of creep of polycrystalline rock salt based on steady-state creep and modified it to incorporate transient creep through work hardening and recovery. An elasto-viscoplastic approach was developed to simulate the timedependent nature of the fracture zone (Malan, 1999). Rheological models were proposed to understand the collapse of iron ore mines in Lorraine by Dragan et al. (2003)."

Jan 1, 2016

With the advent of the First World Conference on Sampling and Blending (WCSB1) in Denmark in 2003 and the subsequent biannual meetings, together with other sampling conferences held on a regular basis, the central tenets of sound sampling practice and theory are spreading throughout the minerals industry. End-users and project houses, or groups who execute the projects, are all now better-informed about the principles of ?correct? sampling and preparation. To support this, many large mining companies now have their own in-house champion who will advise and ensure that the supply of sampling equipment is correct in terms of design and application, which further contributes to improved metallurgical accounting. The presence of a sampling champion also ensures that consistent and acceptable standards in regard to sampling practice are maintained throughout the group. This has, in turn, placed a greater degree of responsibility on the shoulders of sampling equipment suppliers, in terms of their equipment designs and product offerings, as well as applications knowledge for effective installation of equipment on client plants. This paper attempts to highlight the significant challenges that sampling equipment manufacturers often face with regard to complying with the newly understood requirements of best practice and sampling equipment design. Manufacturers invariably face issues with end-users or project houses, including project cost control, restricted headroom for samplers in plant layouts, and a lack of knowledge in certain quarters. These all have a potentially negative effect on the final outcome of a proposed sampling solution or implemented project. In reality, what is intended by all parties and what is ultimately installed are at times very different, with undesirable consequences for all concerned. Against this challenging background, there are, however, a number of instances where intent and implementation are complementary, with very satisfactory results. Keywords sampling, mechanical samplers, design, installation, sampling theory.

Jan 1, 2014

Determination of mineral composition is of significant importance for the mineral sands industry as this information is required for orebody evaluation, the control of mineral processing plants and the determination of product quality. Mineral processing is made more difficult by the presence of pseudorutile, leucoxene, altered-ilmenite and particle inclusions. The paper investigates the properties of such elements from a single product stream using an MLA approach.

Jan 1, 2007

By A. M. Engelbrecht

Paper written on project work carried out in partial fulfilment of B Eng. (Chemical) Membrane processes are vital to a diverse range of technical and biological systems, which also feature in mineral processing applications such as the treatment of mine effluent and extraction of metals. In this study, the use of cellular automata to model a semi-permeable membrane that separates two compartments is considered. Cellular automata are simple models that enable the analyst to represent well-understood local effects, such as the chemical or steric interaction between molecules themselves and between molecules or particles and their environment, which can lead to very complex behaviour on a macroscopic scale. Various physical phenomena, including reverse osmosis, were simulated. Initial results for the effect of temperature, membrane structure and chemical properties of the solutes on the performance of the membrane appear promising. Keywords: cellular automata, dynamic modelling, filtration, membrane fouling, osmosis.

Jan 1, 2007

By J. P. Hoffman

In 1988 the Japan Iron and Steel Federation started a research-and-development programme known as DIOS (direct iron-ore smelting). Eight Japanese integrated steel producers and the Coal Mining Research Centre, subsidized by the Ministry of International Trade and Industry, are involved in the project. The aim of the programme is to have a 500 v/d pilot plant for the production of iron via an oxygen-coal in-bath smelting converter in operation by mid 1993. The three main components of the DIOS process are as follows: ?a fluidized bed for the pre-reduction of iron-ore fumes ?in-bath smelting reduction in a converter ?off-gas reforming by the addition of coal fines. The main drive is to provide a smelting process that is more energy-effective, using coal instead of coke and/or electricity. The advantages claimed include inter alia ?direct use of fine iron ore ?direct use of non-coking coals-low coal consumption ?low capital expenditure-replaces costly coke ovens, agglomeration plants, and the blast furnace ?economical production on mini-plant scale ?less of an impact on the environment. This concept of 'direct steel has been carried over to the production of stainless steel direct from the ores, again bypassing such energy-intensive units as the submerged-arc furnace for the production of ferrochromium. A number of Japanese companies have indicated a certain amount of success. Several interacting elements are recognized that could have a productivity-limiting aspect. The possibility of the direct production of stainless steel from chromite is discussed briefly with reference to the Highveld of the eastern Transvaal as a possible site for such a plant

Jan 1, 1992

By R. V. Ramani

Managers need quality information for effective decision making. This demand, at the present time, is being fulfilled by the increased use of computers via information systems, decision support systems and management information systems. The idea of incorporating intelligence into computers to aid decision-makers has been evolving for over two decades. In recent years, significant progress is reported on applications to business and sciences. In engineering functions, the Artificial Intelligence approach that seems to have great potential is the application of Knowledge Based Systems. The primary objective of this paper is to identify domains in mining engineering where application of knowledge based systems could be beneficial. In- corporation of the expertise required during the analysis and interpretation stages of an engineering design problem through knowledge based systems is recognized as an area of significant benefit. To this end, the components of knowledge based systems for mine ventilation and strata control design are described. The potential applications and limitations of knowledge based systems are outlined.

Jan 1, 1987

By J. Rowe

The attrition of activated carbon, and the loss of gold associated with it, is of significant economic importance to the operation of a CIP/CIL circuit The focus of this study was on activated carbon recovered from an elution circuit which was deemed too fine for reuse. Results of cyclosizer and laser particle size analysis identified that most of the carbon was contained in the larger size fraction suggesting formation by abrasion. Digestion and AAS analysis of the individual size fractions identified a disproportionate concentration of gold in the finer size fractions which was identified by scanning electron microscopy to be due to the presence of fine metallic gold formed as a result of the acid washing process. Attempts to strip the remaining gold using sodium hydroxide or sodium sulphide based solutions proved unsuccessful due to poor elution efficiencies and re adsorption of gold. Upgrading of the material by froth flotation was also investigated using various conventional flotation reagents which had some success in concentrating the free metallic gold, however, grade and/or recoveries were considered less than desirable. Greater success was ultimately found in the transfer of gold from the fine carbon material onto coarser virgin activated carbon using a caustic cyanide solution. Sodium sulphide, sodium chloride and ammonium chloride based solutions were also trialled but proved less successful owing to their inability to mobilise metallic gold or gold cyanide species. Repetition of the transfer process proved capable of stripping 97% of the gold contained on the carbon fines for abed volume ratio of 6:1.

Jan 1, 2009

By John Freer

On 25th November, 1983, nearly forty members of The South African Institute of Mining and Metallurgy, together with Doris Gardner and Judith Money from Kelvin House, travelled by luxury motor coach to Secunda, there to visit the coal-mining and conversion operations of Sasol Limited.

Jan 1, 1984

By B. Yu, M-H. Cao, C. Zhou, X-Z. Zhang

The transient infiltration and lubrication behaviour of slag during continuous casting of steel is important for billet quality. A two-dimensional coupled mathematical mould model was developed to investigate these phenomena. The accuracy of the model was verified by comparing the calculated slag consumption with measurements by the plant. The results show that the liquid slag is consumed from the middle and late period of positive strip time to the next early period of positive strip time, including the entire negative strip time. The maximum downward infiltration velocity and positive pressure in the slag channel is at the middle of the negative strip time. Increasing the positive pressure of the slag channel is conducive to lubrication. The shear stresses acting on the shell surface and at the mould side were determined by the lubrication slag consumption and total slag consumption, respectively, and gradually decreased with increasing slag consumption. The negative strip time was lengthened to increase the slag consumption and prolong the time near the maximum downward shear stress, so as to be conducive to the demould.

Apr 16, 2024