Search Documents

By R. Haldenwang, R. Erasmus, P. T. Slatter, R. P. Chhabra

Notches are used routinely for measuring the flow rate of water with free surface flows. As far as can be ascertained, no work has been done to investigate the performance of these flow rate measurement devices for non-Newtonian suspensions. The Flow Process Research Centre at the Cape Peninsula University of Technology has investigated the flow rate of kaolin and bentonite suspensions from a tank for two notch shapes, namely rectangular and triangular, and for 3 different concentrations of each suspension. The notches were calibrated using water and then the kaolin and bentonite suspensions were tested in them. The rheological characterisation of the fluids was done with a Paar Physica MC-1 rotary viscometer fitted with a cup and roughened bob. Analysis of the results shows a significant increase in discharge coefficient with increase in concentration, and the discharge coefficient has been correlated to the yield stress. This is the first such study, and further investigation is needed to confirm and extend these findings.

Jan 1, 2007

By M. Timucin

High-temperature phase relations in the Pb-PbS system were established by the quenching of samples equilibrated in evacuated and sealed silica capsules. The liquid-miscibility gap seen in some previously published phase diagrams was not observed. The thermodynamic activities of PbS in liquid solutions of this system were derived at 1473 K from the isopiestic equilibration of samples belonging to this solution series with Cu2S-PbS melts of known PbS activities. The behaviour of Pb-PbS melts was found to be compatible with a subregular solution model. This model also made it possible to obtain an analytical liquidus for PbS that was in excelent agreement with the experimental determination.

Jan 1, 1988

By B. Rezai, Z. Pourkarimi, M. Noaparast, S. Chehreh Chelgani

Nanobubbles (NBs) flotation separation can be an indicator for improving the efficiency of fine particles through the conventional process. Since flotation reagents such as frothers can reduce bubble size, they can potentially be used for the generation of NBs and develop a selective NB flotation separation. This study explored the flotation separation of fine phosphate particles from their associated minerals in the presence of NBs, which were generated by using a phosphate flotation reagent (Flo-YS: collector-frother). The results of flotation tests showed that in the presence of NBs, the flotation efficiency was significantly improved. However, in the presence of NBs, surface chemistry analyses (Fourier Transform Infrared Spectroscopy and High-Performance Liquid Chromatography) illustrated that the collector adsorption on the surface of phosphate particles decreased. A comparison between outcomes of various phosphate flotation conditions indicated that increasing the flotation efficiency in the presence of NBs may be due to the aggregation of fine particles by the generated NBs, and also selective adsorption of NBs (hydrophobisation) on the surface of particles. In other words, generating NBs by selective collectors may increase efficiency and decrease the collector consumption of a flotation process. Keywords: Phosphate, selective separation, fine particles, collector-frother, efficiency, mechanical flotation cell

Jan 1, 2020

By A. Schippers, S. Hedrich

Chalcopyrite represents the most important copper resource and is currently mainly exploited using pyrometallurgy. Bioleaching is an environmental-friendly and economic alternative to conventional mineral processing technologies. The technical feasibility of stirred tank reactor bioleaching of copper ore concentrates using acidophilic iron-/sulfur-oxidising bacteria is proven, however, often incomplete due to inefficient chalcopyrite dissolution. A decoupling of bacterial growth from bioleaching activity in one bioreactor by adjusting appropriate temperatures for both process steps allows for almost complete chalcopyrite dissolution. Separation of copper and recovery of other metals from the PLS was possible by implementation of different biological and chemical techniques. The Ferredox process has been proposed to treat limonitic laterite ores for cobalt and nickel recovery by means of anaerobic reductive dissolution with autotrophic, acidophilic bacteria. As a modification, aerobic reductive dissolution of laterites with acidophilic bacteria has shown economic and environmental advantages over anaerobic reductive dissolution. The reductive bioleaching technology has the potential to increase metal recovery in existing mines, and transform unexploited ores and limonite stockpiles into valuable resources. Keywords: Biomining, bioleaching, chalcopyrite, laterite, Ferredox process

Jan 1, 2020

By G. P. A. Howe

"A computer model of the rutile, ilmenite and zircon industry was developed jointly by Associated Minerals Consolidated and Consolidated Gold Fields for exploring marketing strategies and making predictions over a ten-year period. The industry is described briefly and the reasons for modelling it and choosing a deterministic approach explained. The economic structure of the model and its level of complexity are discussed. The necessity and techniques for convenient input and clear output, the team composition and the method of work are discussed.The reasons for the choice of FORTRAN, large computers, remote batch terminals and the vital importance of fast turn-round are discussed.Costs in staff time and computing are given, with an assessment of the reasons for the success of the model. The model is used on a regular basis to aid management decisions."

Jan 1, 2014

By B. Aydin, A. S. Aloglu, S. Kahraman, E. Saygin

"The coal strength parameter is used in operations such as the selection and design of mechanical excavators and coal crushing/grinding equipment. However, coring or cutting prismatic specimens from coal for the standard strength tests is difficult, and sometimes not possible. For this reason a method for the indirect determination of coal strength from easy tests would be useful. In this study, the predictability of coal strength from the needle penetration test was investigated. This is a very easy and practical test method. Point load and needle penetration index (NPI) tests were carried out on coal specimens from Çayirhan coalfield in Turkey. The point load indexes were converted to the uniaxial compressive strength (UCS) values by using the general conversion factor. The UCS and NPI values were evaluated using regression analysis. A strong linear relationship was found between the two parameters. The conversion factor for the UCS-NPI ratio is 0.35 for the tested coal samples. It is concluded that the UCS of coal can be predicted from the NPI.IntroductionKnowledge of coal strength is important for the selection and design of mechanical excavators and coal crushing and grinding equipment. Uniaxial compressive strength of coal is used in designing pillar dimensions in room and pillar mining. Coals always contain bedding planes and cleats; they are also brittle and fragile. Therefore, coring or cutting prismatic specimens from coal for the standard strength tests is difficult, and sometimes not possible. For this reason, a method for the estimation of coal strength from easy tests would be useful.The needle penetration test is a nondestructive index test that is applicable both in the field and the laboratory and does not require any special sample preparation. The test has been used for the estimation of physical and mechanical properties of weak or soft rocks (Okada et al., 1985; Yamaguchi et al., 1997; Takahashi, Noto, and Yokokawa, 1988; Uchida et al., 2004; Aydan et al., 2006; Aydan, Watanabe, and Tokashiki, 2008; Aydan, 2012; Erguler and Ulusay, 2007; Park, Obara, and Kan, 2011; Ulusay and Erguler, 2012; Aydan and Ulusay, 2013; Aydan. Sato, and Yagi, 2014). This study investigates the predictability of coal strength from the needle penetration test."

Jan 1, 2017

By S. A. Ghoreishi-Madiseh, F. P. Hassani, H. Rafezi, H. R. Manouchehri, A. Shadic, A. P. Sasmito

Weakening rocks by taking advantage of microwave-induced microcracks is a promising solution for comminution processes. This paper investigates the effects of microwave treatment of the rock/or samples in single and multi-mode cavities. Based on the experimental results of using a 2.45 GHz microwave generator, the performance of different cavity setups and their impact on the energy effectiveness of the microwave irradiation was examined. Physical interpretations were drawn from multiple experiments with a relatively wide range of power rates and exposure times. Both basalt and kimberlite samples were used in experiments, and their results were systematically compared. For single-mode cavity tests, a microwave applicator waveguide antenna was placed at different distances from the samples to evaluate the effects of sample positioning on microwave heating, both numerically and experimentally. Eventually, cavity performance was assessed by using calorimetric test results, and strength decay was documented based on the spallation of the samples. It was found that the singlemode cavity setup has unique properties that can significantly improve the electromagnetic heating and therefore, strength degradation process. Keywords: Microwave, fragmentation, energy effectiveness, calorimetry, mine-to-mill

Jan 1, 2020

By J. -M. Chautru

A geostatistical simulation of a typical mining site for polymetallic nodules in the North Pacific Ocean is presented. This is the first stage in the design of an industrial mining system. Two variables which have a major effect on the orebody's economic potential are considered, namely: the maximum slope of the ground inside a mining block of 50 x 100 m; and the average quantity of nodules on the same support. Two geostatistical problems have emerged in this study. The first is due to the lack of a change of support model for the maximum of a variable. A provisional solution, considering an experimentally accessible 'equivalent' support, is proposed. The second is due to a non-linear link between the two variables. To be able to take this into account in the simulation, we propose a new method based on the decomposition: X = E(X/Y) + Residue (X). Satisfactory results were obtained with this approach.

Jan 1, 1987

By E. S. van Druten, M. C. Bekker

"The complete and successful closure of a mine in the South African environment remains problematic. Closure remains an elusive mining phase due to unclear roles and responsibilities, inaccurate closure management data, and the inability of stakeholders to conceptualize and integrate closure information into business processes. Currently there are no proven methods available to address the complexities encountered during a closure application, and to date no mine has been granted full closure. Many mines are left abandoned and unrehabilitated, resulting in risk to investors, surrounding communities, and regulators. This investigation aimed to determine, categorize, and rank reasons for unsuccessful mine closures. Focus groups consisting of public and private stakeholders were identified and surveyed through a structured, rank-order questionnaire to determine the relative importance of reasons why achieving formal and final mine closure remains elusive. Various requirements and aspects were identified and listed according to four categories: namely, primary, secondary, process drivers, and information sources. These aspects should be considered in the development of an integrated mine closure model.Background and rationalePrior to 1956, mine closures were not subject to legislative requirements, being merely governed by insufficient environmental regulations under the Mines and Works Act 27 (MWA) (Swart, 2003). In 1981 the Chamber of Mines (COM) published a document titled ‘The rehabilitation of land disturbed by surface coal mining’, which constituted the first notable contribution to environmental protection. This guideline was later referenced in the Minerals Act of 1991, which for the first time laid definite environmental burdens on the Mining Right Holder (MRH). The Minerals Act of 1991 was superseded by the current Mineral and Petroleum Resources Development Act (MPRDA) and the Mineral and Petroleum Resources Development Act Regulations (MPRDAR), which specify a regulatory process for mine closure applications and financial provisions."

Jan 1, 2017

By C. Massola, E. E. M. N. de Guzmán, M. G. Bergermana

The abrasiveness of a mineral or rock is an extremely important topic in the mining industry and is generally measured by the Bond abrasion index (AI). However, to determine such an index by the Bond test requires 1,600 g of sample with particle sizes ranging from ½” to ¾”, which are not available in certain situations, such as ore prospecting, drilling, and geometallurgical studies. In order to investigate the abrasiveness of smaller-sized sample materials, a modified LCPC test was developed, which allows testing fine materials (i.e., 1.0 mm or smaller) to predict wear in ore processing circuits and anticipate possible failures resulting from changes in abrasive characteristics of the ore being processed. The results for 16 different materials indicated a good correlation with the AI and the modified LCPC, resulting in a reliable alternative for the AI. Keywords: Bond Abrasion Index (AI), LCPC, abrasiveness

Jan 1, 2020

By R. Hewer

Transition metals have been widely used in medicine throughout history. The medicinal use of metals extends back to the earliest recorded history when the Chinese used gold as treatment for a variety of ailments. The ancient Egyptians used copper to sterilize water and mercury was reportedly used by Hippocrates in 400BC. Thereafter, numerous other metals have been used as treatment throughout the centuries. For example, zinc sulphate was used as an emetic in the 17th century and zinc oxide was used to treat epilepsy in the 18th century. This use of metals, and numerous other instances, which have been well described in Sneader 2008,1 make for interesting reading but largely occurred prior to the advent of rigorous scientific method. Therefore, although there are exemptions, most therapeutic applications of metals prior to the modern age lack scientific grounding and have been found to be mostly ineffective. Of more relevance are metal-based medicines approved by regulatory bodies (i.e. Food and Drug Administration; FDA) that are in current use as therapeutic drugs. There are presently a large number of metal-based drugs that are approved for use by the FDA ranging from over the counter medicines, such as bismuth subsalicylate for gastrointestinal problems, to prescription drugs such as lithium carbonate for the treatment of manic depression. The list of metal-based medicines approved by the FDA not only incorporates base metals but also includes precious metals. Platinum complexes have been found to be potently active against several different types of cancers while gold complexes have shown application as treatment for rheumatoid arthritis (RA). With the well-established foundation that exists for metal-based medicines, it is imperative to continue exploration into new therapeutic areas. The precious metals; gold, ruthenium and platinum, continue to attract scientific interest in the field of biomedicine and have been widely researched. Scientific studies conducted on gold complexes have demonstrated the potential of this metal for the treatment of HIV/AIDS, cancer and malaria. These diseases are also specific health concerns for developing nations; countries where disease has devastating impact. Within South Africa alone, an estimated 5.7 million people are infected with HIV/AIDS,2 approximately 7 000 new cases of malaria are reported annually, and it is projected that 1 in 4 persons will develop cancer. Continuous development of therapeutic drugs to combat these diseases is therefore apriority, and the exploration of gold-based compounds for this purpose is warranted.

Jan 1, 2009

By L. M. Tavares, T. M. Campos, P. M. Faria, R. M. Carvalho

Recent advances in mechanistic ball mill modelling are expected to allow for more accurate predictions that overcome the well-known limitations of phenomenological approaches, including their inability to predict the effect of liner geometry and their wear, in grinding. Although able to describe continuous operation, the UFRJ model of ball mills has only been validated in the past in mills that operate in batch mode, either in laboratory or pilot scale. The present work demonstrates the application of the mechanistic UFRJ ball mill model to predict fine grinding of iron ore in a pelletising plant in Brazil, the first application of such a mechanistic modelling in continuous mode. It shows that the model provides accurate descriptions of flows after iterations in a closed-circuit with hydrocyclones. Keywords: Ball mill, iron ore, grinding, modelling, particle breakage

Jan 1, 2020

By Y. Jiao, V. S. Thompson, D. W. Reed, Y. Fujita, J. E. Aston

Rare earth elements (REE) are vital components in modern electronics and green technology products. Supply is tight and global demand is expected to increase, leading to high risk for the economic and national security of countries largely dependent upon foreign supplies. Recycling of REE from consumer and industrial waste materials is a possible way to help meet demand. We have shown previously that biohydrometallurgy can play an economically and environmentally sustainable role in REE recycling, particularly if agriculture or food wastes are used to produce organic acid bioleaching agents. A challenge for organic acid-based bioleaching is the incomplete conversion of the carbon substrate to an optimal organic acid biolixiviant with high REE extraction capability from a variety of REE-containing feedstocks (e.g., mining wastes, magnets from end of life products, spent batteries, etc.). To help meet this challenge a metabolic model was developed for Gluconobacter oxydans to identify options for improving sugar conversion to organic acids. Model predictions were consistent with laboratory data for the microbial consumption of glucose and production of gluconic acid, and suggested that providing growth conditions with relatively high C:N molar ratios could result in lower pH biolixiviant production and thus improve bioleaching. Keywords: Gluconobacter oxydans, bioleaching, metabolic modelling, rare earth elements summaries 2019: U.S. Geological Survey, 200 p., https://doi.org/10.3133/70202434.

Jan 1, 2020

By S. Banisi, S. M. Mousavi, S. D. Tafvizi, Gh. A. Parsapour, M. Mahmoudi

Generally, regrind circuits are used to increase the degree of liberation of value minerals which are fed to flotation circuits. At the regrind circuit of the Sarcheshmeh copper complex, four ball mills are in closed circuit with their hydrocyclone clusters. In the initial design of the plant, feed and underflow percent solids, and pressure drop of the hydrocyclones were 39% and 65%, and 15psi, respectively. Over the years, due to a reduction in the feed grade from 1.17% to 0.67% and changes in the operational conditions, the feed rate to each hydrocyclone cluster has decreased from 401 to 70t/h and consequently the pressure drop, feed and underflow percent solids have reduced to 4psi, 17% and 25%, respectively. The main objective of this research was to audit the feed solids concentration and pressure drop of the hydrocyclones and make the necessary modifications based on the Plitt’s model. The results of sampling showed that water recovery to underflow was 59% which was higher than normal values. By reducing the number of operating regrind mills from 4 to 2, the feed rate to each mill increased. After this modification and taking necessary measures in the plant to implement the new operating approach, the pressure drop, feed and underflow percent solids increased to 18psi, 28% and 58%, respectively. The water recovery of the hydrocyclones underflow decreased from 59% to 12%. These changes in addition to increasing the circuit efficiency saved 1000 kWh energy and decreased ball consumption by 925 ton/year because of reduction in the number of operating ball mills. Keywords: Regrind mills, flotation, audit, troubleshooting

Jan 1, 2020

By D. Amariei, G. Bartolacci

Preconcentration of precious and base metal ore types is becoming more relevant with the discovery, the development and the operation of many lower grade deposits around the world. Ore preconcentration designates an operation consisting of sorting an ore to reduce the quantity of waste material sent to the concentrator. It can be seen as rejecting waste material as much as possible, without compromising the recovery, or as the recovery of as much valuable metal as possible into an optimum mass yield. Benefits of preconcentration are multiple: grinding energy savings, costs reduction, lower environmental footprint, extension of the reserves, etc. However, all of these benefits do not apply simultaneously and are not applicable to each ore type. Technologies employed for preconcentration are highly dependent on ore properties, especially on the particle size at which the gangue is liberated. Thus, from coarser to finer particle sizes, technologies such as screening, ore sorting, gravity separation (Dense Media Separation (DMS) and jigs) and coarse flotation could be used for the rejection of liberated gangue. The difficulty starts when a benchmark is needed to select a suitable technology, especially for low-grade gold deposits. This paper presents the challenges of comparing lab-scale technologies (DMS versus jig) for gold preconcentration. The experimental data will show to what extent comparing two lab-scale gravity technologies for gold preconcentration can be challenging. An attempt to evaluate the energy savings by assessing the hardness of the tailings after gravity separation will also be presented. Keywords: Challenges in gold preconcentration, gravity separation, jig, dense medium separation

Jan 1, 2020

By S. Kahraman

P-wave velocity measurements were carried out on 22 large limestone blocks in a stone processing plant. In the laboratory, P-wave velocity of core samples was measured to obtain intact rock velocity. The square root of the ratio of the velocity of the large stone block to the velocity of the core specimen was called the velocity ratio index (VRI) and a quality classification for large building stones was suggested. In addition, the applicability of the established classification to stone cutting with gang saws was checked. It was concluded that the quality classification and estimation of slab production efficiency of the building stones can easily be made by ultrasonic measurements. However, the study was carried out only in limestone. Further study must be conducted to check the validity of the obtained results for the other rock types.

Jan 1, 2007

By J. Yianatos, P. Vallejos

In the last decades, the exponential increase in the cells’ volume resulted in significant advantages such as investment costs, footprint and energy savings. However, in larger size cells, despite the increased diameter/height ratio, new constraints arose related to the need for decreasing the larger froth transport distances to enhance the froth recovery. Thus, the use of froth crowders and internal launders became compulsory to maintain the froth transport distances but decreasing the ratio between gas and collected mineral flowrates. Consequently, the bubble load will increase until reaching a critical bubble surface coverage. In this paper, the concentrate carrying capacity (tph/m2) is described in terms of the bubble surface coverage (bubble loading) at the pulp-froth interface and the froth recovery (froth transport) and is evaluated as a function of the cells’ volume and operating variables. A sensitivity analysis, based on industrial operating and design conditions, such as superficial gas rate, particles size, froth crosssectional area and cells’ volume, was developed for evaluating the metallurgical performance of cells from 100 to 630 m3. Results show that limiting carrying capacity can arise for the whole range of cells’ volume, depending on critical operating conditions, particularly in first rougher cells and cleaning stages of industrial flotation circuits. The increase in cells’ volume consistently increases the bubble loading (bubble surface coverage) under all conditions, approaching the limiting conditions more rapidly in the case of cells without internal launders. Otherwise, the limiting condition was achieved when the particle size DPS decreased from 50 to 20 (μm) and for superficial gas rates significantly less or larger than 1 (cm/s). The use of internal launders allows for increasing the range of the operating conditions needed to reach a certain carrying capacity. Keywords: Bubble carrying capacity, flotation cells, bubble surface coverage, cells’ volume

Jan 1, 2020

By R. L. Robinson

An analytical framework is formulated to assist mining companies in assessing the relative merits of mineral exploration and acquisition strategies. The anticipated costs, risks, and returns of each strategy are conceptualised using decision trees. Economic criteria - expected net present value, expected return per unit of investment, and the probability of success - for each strategy are derived(from the appropriate decision tree network. Application of the analytical framework is illustrated using the example of a medium-size company in the Canadian base metal sector.

Jan 1, 1987

By M. Tang, X. Tong

"SynopsisSlime coating is one of the most common ways for serpentines to contaminate metallic mineral concentrates during traditional flotation of coarse sulphide particles. This could pose quite a complicated and challenging problem in the case of some types of low-grade and finely disseminated Cu-Ni ores bearing high serpentine contents. This is the case for the copper and nickel sulphides from the Yunnan Mine, China. Previous batch flotation tests of this ore resulted in satisfactory recoveries of 86.92% Cu, 54.92% Ni, and 74.73% Pt+Pd, and concentrate grades of 4.02% Cu, 3.24% Ni, and 76.61 g/t Pt+Pd. However, the MgO content in these concentrates was more than 19%. In the current study, microflotation tests and settling rate tests were introduced to investigate the effects of a combination of strong collectors (a 2:1 weight ratio of butyl xanthate and butyl ammonium dithophosphate) on entrainment of serpentines in metallic mineral concentrate, as well as visual observations of the concentrates in suspension using still photography. All test results indicated the presence of serpentines entrapped in the hydrophobic flocs that resulted from these collectors, even with the use of effective gangue depressants. These strong collectors are used to flocculate the ultra-fine sulphides by forming loose and ‘fluffy’ hydrophobic flocs. However, these hydrophobic flocs may also be able to load or entrap some serpentine slimes into the concentrate, and this entrained serpentine could be harder to remove by using depressants or intensified conditioning than serpentine slime coating on the particle surfaces.IntroductionSerpentine minerals, which have the generalized composition (Mg,Fe)3Si2O5(OH)4, can be easy to crush and grind due to their convoluted and bent layered structures. These serpentines can hinder the enrichment of some metallic minerals and dilute their concentrates by entrainment during flotation. The resulting high pulp viscosities, slime coatings, and high content of dissolved ions adversely affect the flotation recoveries of copper and nickel sulphides, and high levels of MgO entrained in the concentrates lead to heavy penalties from smelters. Since the quality of nickel flotation concentrate depends heavily on its MgO content (generally less than 6–7% for No.1 or 2 grade nickel concentrate according to the standard requirement from National Nonferrous Industry), reducing the entrainment of serpentine during flotation is becoming more and more pressing. Previous research has focused on the collectors and depressants that are commonly used in copper-nickel flotation, as well as their interaction mechanisms."

Jan 1, 2015

By S. Banisi, S. Zare, M. Mahmoudi, M. Maleki-Moghaddam, M. Yahyaei

As the orebodies become more complex and lower grade, there is an increasing demand from crushing circuits for a finer product. When the product from a crushing circuit does not satisfy the requirements of the downstream processes, the cost of production increases. Thus, enhancing the performance of cone crushers through optimisation of their operating factors becomes important. One of the key factors affecting performance of cone crushers is the filling of the crushing chamber during the operation. The effect of varying the filling of the crushing chamber of a cone crusher was investigated. To assess the crusher performance, parameters such as crusher capacity, power utilisation, and reduction ratio were used. Extensive plant trials were conducted to obtain samples and operational data when the crusher chamber was 50% full (half-full) and 100% full, which is 300 mm above the top of the crusher chamber (super-choked condition). The results indicated a 62% difference in the crushing capacity when the crusher was operated in a super-choked condition compared to the half-full chamber level. In the super-choked condition, the size-specific energy at 12.7 mm was 20 % lower than that of the half-full condition. The Bond ball mill work index (BBWI) of crusher product indicated that the BBWI of the product of the super choked condition is 5.6% less than that of the product of half-full condition. This can be attributed to the generation of micro cracks in particles due to increase in the interparticle breakage when the crusher was operated in the super-choked mode. Keywords: Cone crushers, crushing efficiency, crushing chamber filling

Jan 1, 2020