Search Documents

Jan 1, 1938

By T. H. Butler

February 22nd, 1926. Mr. Benedict Shubart, 521 Boston Building, Denver, Colorado. Dear Mr. Shubart: At your request, am submitting to you several suggestions for the amendment of our safety code which you felt should be kept up to date. As before, am advising you that these suggestions do not have the approval of the entire Safety Committee, but rather are the individual opinions of several members who have expressed their wishes in the form of letters to me. I am particularly indebted to Mr. Dan Harrington and Mr. Wm. Littlejohn for their assistance. Would recommend the following amendment a to the various sections. Section 1. Wherever possible trolley wires should be securely hung to roof or timbers at a distance of not less than five feet and not more than six and one-half feet above rail and six inches to one side. Spacing of hangers should be from 20 to 25 feet apart. Section 2. 500 volts D. C. should not be allowed in any installations. Trolley wires should not carry a voltage of more than 250 D. C. Pumps, mining machines and other small machinery units where A. C. power is used should not carry a voltage of more than 220. Large units, such as pumps, motor genera- tor set and hoists, may use a voltage of 2,200. When power cables to operate same are of armored construction, cables should be securely buried at all crossings. Section 4. Where power lines pass through door frames or stoppings they should be properly insulated with porcelain or rubber tubing. Whenever men get on or off man-trips in vicinity of trolley wires same

Jan 1, 1926

Jan 1, 1932

Jan 1, 1928

By Bret K. Clayton

Jan 1, 2004

By C. H. Trik

Any article or discussion on the ventilation of Working Faces under different systems of concentrated mining is of little value to any practical man unless based upon facts gleaned from actual experience, and empirical data on this subject is, to say the least mighty scarce. Of this one thing, however, you can rest assured, the old cry of "no air at the working faces" will have become a thing of the past. No longer will we hear of some operator who has been too eager to get out the coal and who has lost sight of everything else in his mad dash for production, digging himself shut until his airways are mere pin- points and his air current a feeble thing, too weak to combat the high resistance of his restricted mine. A mine operating under one or more of the various systems of concentrated mining should always have plenty of air, for in concentrated mining the tendency is toward greatly reduced mine resistances due to increased sectional areas. It can readily be seen that the tendency is to large, wide areas across the panel and where this is true large volumes and low gauges are the rule, unless inordinate restriction is encountered in the permanent airways, and no operator, far sighted or progressive enough to adopt this system of mining when his conditions permit, would ever allow his main airways both intake and return, to be anything but model courses. As a matter of .fact, we are likely to encounter the opposite of what is usually the case in most mines to day. We are apt to find the air at the working faces sluggish due to the large areas of passage rather than to high resistance. This is combated in. various ways which will be discussed further along in this article. Those companies, of which we have knowledge in this country who, to- day are using any of the new systems of mining, seem to proceed alike in the general method of developing their acreage. Let us assume, for this discussion, the Utah Colorado Coal Corporation is going to open a mine under the new system and their conditions are such as to permit their adopting the simple block system, each face served by a separate machine, each entry having its conveyor to the cars. After the permanent haulage and airways are driven "narrow work" starts to shape the blocks. We are not interested in the length of these "conveyor headings" since we do not need to drive breakthroughs nor build stoppings for ventilation until we have reached their end when we connect them together. We have two methods of sending air to the face of these dead ends. We can laboriously and expeilsively install brattice cloth, as we go, or we can use a small auxiliary blower with canvas tubing to the face. Indeed I may say that one of the great difficulties encountered under the new systems is in the ventilation of these narrow faces. After they have been connected and an air circuit or current established, ventilation becomes plain sailing until the block is worked out. The auxiliary blower when used with flexible canvas tubing, has been found to be the ideal answer to the question of how to ventilate the headings which are anywhere from 100 to 1,000 feet long. These small blowers when properly used, can go a very long way to assist in further reducing the cost of production already assured by the new method of mining. Right angle bends are made by the tubing manufacturers to enable the fan to sit in the fresh air current, yet out of the way of operations and any recirculation is positively avoided by blowing the air around the corner to the face.

Jan 1, 1926

By Kirk Nobis

Develop a Risk Management Plan for Your Mine ? Why? ? Measuring ? Managing ? Conclusion

Jan 1, 2006

By Jeff Mattern

Topics of Discussion ?Navajo Mine General Information ?Mapping, Photogrammetryand Image Fans ?Planning: Equipment, Control Points, Targets ?Digital Photography ?Software Manipulations: Image Matching, Creating a 3d Image and Triangulation, ?Mapping? Geologic Structure, Data Analysis ?Conclusions ?Other Applications

Jan 1, 2005

The 69th Regular Meeting of the Rocky Mountain Coal Mining Institute convened in Manor Vail Lodge, Vail, Colorado, and was in session at 10:00 a.m. The meeting was called to order by Past President Joseph E. Ward, former District Manager, Denver Office, Coal Division, Joy Manufacturing Co. and now retired. Mr. Ward, after reading a brief biography of President O. F. "Os" Lewis, introduced him to the assembly. Biographical sketch read as follows: Mr. Lewis is President, General Manager, and a Director of Colowyo Coal Company. "Os" was born in Reno, Nevada. He attended the University of Utah at Salt Lake City, Utah, and later the Denver University in Denver, Colorado. His career in the Western Coal Industry started back in 1923 when he was employed by the Central Coal and Coke Company of Salt Lake City, Utah, as a clerk, then chief clerk and as a traveling sales representative for a period of 13 years. Later, in 1936, when that company was acquired by an affiliated company of Harris Coal Company, he was transferred to Denver as Assistant Sales Manager, Purchasing Agent and later as Executive Assistant to the President.

Jan 1, 1973

By D. C. McKeehan

The use of electric power was introduced in this field in the year 1892. The initial installation being an engine-driven generator and one nine-ton haulage locomotive using 500-volts direct current. Reference to this locomotive appears in the issue of COAL AGE for February 24, 1921. For a large coal field, the conversion to electricity has been very complete, there being no compressed air machines in service and but one steam driven hoist, that at No. 1o mine and located within fifty feet of the present power plant boiler room. Two eight-ton haulage locomotives, installed in 1896 and still in use, justifies the service and the equipment. These mines used the pioneer types of electric cutting and drilling machines, the story of which is, no doubt, familiar to you. The extensive use of electric power began in 1900, when there was installed four 400 k.w., 500-volt direct current engine-driven generators. These were cross-compound machines and operated non-condensing. By 1910 the mines had developed main haulage entries of several miles in length and a working territory of about six square miles in area. The necessity of supplying adequate power at the working face required a local power supply from motor-generator sets in various parts of the mine to supplement the power furnished by the engine-driven generators. The power to these motor-generator sets was supplied by a 300 k.w. high pressure non-condensing turbo-generator delivering 2300 volts, 60 cycle, three-phase current. This marks the beginning of the use of alternating current for mining purposes. In 1913 new mines were being developed at Reliance, seven miles distant, and the plant was enlarged to accommodate a 750 k.w. low pressure, condensing turbine, utilizing the exhaust steam from the cross-compound engines and the 300 k.w. turbine. Transformers were installed for supplying Reliance with power at 13,200 volts. In the course of time the old engines began to dismantle themselves by throwing various pieces, such as cylinder heads, about the building, damaging walls and switchboards, and created a general feeling of unrest among those who had to do with power production. The limitations of the old engines that had given admirable service for ten years were recognized. The source of exhaust steam became questionable and in 1915, a 1000 k.w. high pressure condensing turbine was installed in order that a more general use could be made of motor-generator sets for the direct current supply. The plant at that time containing a 1000 k.w., a 750 k.w., and a 300 k.w., in alternating current generators, supplemented

Jan 1, 1921

Jan 1, 1929

By David Scrymgeour

All low cost coal has been mined. Engineers are searching for a safe and effective way to mine coal seams' deep within the earth. The most modern of these is the RL, an acronym for Robotic Labor. Mining robots are programmed to do specific jobs but can think on their own during an emergency. MR's, or mining robots, usually have a same basic shape. A torso is mounted on treads. Designers chose treads because it gives the robot a great deal of mobility. The torso has two arms. One arm is equipped with a human hand. The other has a human-like hand. Mining is done underground. A small robot goes around punching holes in the coal. A small charge is inserted in the hole. The MR ignites the charge with his laser. It explodes after three minutes. The MR returns to the station where his battery is recharged. Mobile cement barricades are moved between the blasting area and other working MR's. After the charge explodes the barricades are moved to another area. The MR returns and cuts the coal chunks into pieces. Another robot comes and loads the coal and carries it to the loading bin. From there it is taken to the surface where it is weighed and shipped. The whole process was done by robots. Humans just supervise but help in an emergency or malfunction.

Jan 1, 1987

Jan 1, 1950

By Graham Bright

Up until a few years ago most of the electrical equipment used in the mines of this country was developed for industrial purposes and was adapted for use in mines by slight modifications. It became apparent, however, that mining conditions differed widely from most industrial applications and it became necessary to design and develop apparatus, particularly suited for use under mining conditions. Most of the electrical apparatus used in mines today, however, does not owe its success entirely to mining development, but in many cases developments in other branches have been taken and improved upon and modified to meet mining conditions. Power Plant: In the earlier days the power plant for the production of electric power usually consisted of fairly small belt driven direct current generators operated from reciprocating non-condensing steam engines. Today where possible the mines purchase power from central stations and where not possible it is ususally produced from turbine driven plants using non-condensing turbines for the smaller plants and condensing turbines for the larger plants. The bad water conditions at many of the coal mines in this country is, responsible in a large measure for the high cost of upkeep and repairs in isolated power plants. This feature with the type of labor available makes it difficult to operate an isolated plant condensing except in the larger mines where water conditions are good and the apparatus can be taken care of. The geared turbine is a particularly simple and rugged piece of apparatus and requires very little attention over long periods of time. Hoists: The first electric hoists to be installed used various types of motors designed for railway or industrial purposes, and the control furnished was far from satisfactory. Today most of the mine hoist motors are of the alternating current type, especially designed for hoisting service. The control for motors of 200 H. P. or over is usually of the magnetic of liquid rheostat type, and as built today will operate over fairly long periods with a very moderate cost of up-keep. Hoists of 1000 H. P. or larger are usually of the direct current type using field control and receiving power from a flywheel or synchronous M. G. set. Hoists of this type have made remarkable records in regard to continuity of operation and low cost of up-keep. Where high speed operation is desired in either coal or metal mines, the D. C. equipment using field control and a separate M. G. set to supply power to the hoist motor is not only the safest and most economical but in many cases is the only type of equipment capable of satisfactorily obtaining the output required. A number of improvements have been brought out with the field control scheme in connection with the acceleration, retardation, overfeed and overwind of the hoist. With these new developments the hoist operator can no longer abuse the hoist by improper manipulation of the control handle. Until a few years ago the matter of safety devices was not given much consideration when installing hoisting equipment. At the present time the safety devices are considered one of the most important items in connection

Jan 1, 1922

[ ]

Jan 1, 1995

Jan 1, 1983

Jan 1, 1990

MR. GERALD ALLEY (C 11 i e f Draftsman, C. F. & I. Co.) : This invention is primarily intended to correct anything that goes wrong with the fan and any conditions in your air current underground which do not produce a change in your fan water gauge

Jan 1, 1925

Jan 1, 1991

[CURTIS M. BELDEN RMCMI PRESIDENT 1999-2000 on behalf of the RMCMI Board of Directors and Officers of The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 96th Regular Meeting and Convention to be held June 25 thru June 27,2000 Durango, Colorado]

Jan 1, 1999