Search Documents

By Charles Sabine

The U.S. Bureau of Mines studied mines and prospects in the Bristol/Granite Mountains Wilderness Study Area (WSA) in 1982. The 45,000 acre WSA, located in the eastern Mojave Desert of California, is underlain by Mesozoic plutonic rocks with scattered roof pendants of Paleozoic (?) metasedimentary rocks. Two mines and six prospects are identified; one mine, the Silver Lode Mine, and a prospect of unknown name are adjacent to the area. The Silver Lode Mine has occurrences of silver, lead and zinc. Within the study area, the Comanche Mine has occurrences of iron and copper and the Iron Victory Prospect has an occurrence of iron. None are large enough to constitute a resource. Occurrences of magnesian marble at the Comanche Mine, Iron Victory Prospect, and elsewhere in the area contain too much MgO for commercial use other than agricultural soil supplements or crushed stone. Transportation costs to markets would exceed the value of the rock. At the Comanche Mine, situated in a roof pendant of marble, about 10 tons remain of a 110-ton pod of magnetite which contained 42.5% iron, and less than 50 tons remain of a mineralized fault breccia which averaged 2.5% copper and 0.3 oz/ton silver. Magnesian marble contained 41 to 45% CaO and 14 to 16% MgO. Primary and secondary silver, lead, zinc, and copper minerals are disseminated along altered joints and in quartz veins in quartz monzonite at the Silver Lode Mine, adjacent to the WSA. Analytical data are sporadic; samples contained as much as 0.12 oz/ton gold, 1.8 oz/ton Silver, 1.1% lead, 3.8% zinc, and 0.3% copper. Mineralized zones in the workings are not resources, but they might indicate possible silver-lead-zinc resources at depth. At the Iron Victory Prospect, lenses of magnetite and hematite with some chalcopyrite occur in a skarn lone in a marble roof pendant. About 110,000 tons of iron-rich rock, averaging 47.2% iron, are present; the largest lens contains about 30,000 tons. About 150,000 tons of magnesian marble, averaging 41.0% CaO and 11.7% MgO, are also present. Deposits of stone, and sand and gravel in the WSA are too distant from markets to be resources. Occurrences of energy minerals were not identified.

Jan 1, 1984

By N. A. Pace

This is one of a series of papers being published by the Federal Bureau of Mines for the dissemination of information on methods and practices used in the mining and preparation of crushed stone for market requirements. Performance in terms of units of work or tons produced per machine and per operator man-hour are given whenever that information is available. Direct operating costs are useful for comparing different methods, and are, therefore, included if possible. In addition to the factual description of equipment and methods used, it is desirable to discuss the engineering reasons for the choices that have been made. This paper is particularly concerned with the opertions at the Columbia plant of Palmetto Quarries Co. of Columbia, S.C. The plant is about one-half mile east of the Congaree River and adjacent to the southwest corner of the city of Columbia. Rail access is by the Atlantic Coast Line Railroad, and by a spur strack of the Seaboard Airline Railroad.

Jan 1, 1962

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d'Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

By T. T. Campbell

This investigation was undertaken by the Bureau of Mines to determine if high-purity ductile molybdenum of uniform quality can be prepared by bomb reduction techniques. Molybdenum trioxide (Mo03) and mixtures of molybdenum dioxide (Mo02) and trioxide were reduced by magnesium in closed steel bomb reactors. Very high pressures in excess of 5,000 p.s.i. developed during magnesium reductions of Mo03. The addition of calcium oxide to the bomb charges caused a significant reduction in pressure. Reaction efficiencies higher than 95 percent were obtained during magnesium reductions of either Mo03 or mixtures of Mo02 and Mo03, but high pressures were encountered when the charges contained from 30 to 60 percent Mo02. Reaction efficiencies were usually low (less than 80 percent) when the bomb charges contained more than 40 percent Mo02. The charges with the best composition considering operating pressure, yield, and purity contained from 10 to 30 percent Mo02. The addition of small amounts of carbon to the reaction charges was helpful because some deoxidation occurred during the reduction and also during subsequent arc-melting of the regulus metal. The purity of the bomb-reduced, arc-cast molybdenum metal ranged from 99.2 to 99.8 percent and in some instances the metal contained as little as 5 parts per million oxygen.

Jan 1, 1962

By M. Leva

WITH the development of new processes for the production of synthetic liquid fuels, an extensive literature search was undertaken to uncover fundamental relationships between fluid and heat flows and the operating variables of new types of converters. Examination of published correlations revealed that considerable uncertainty existed in the correlation of the operating variables of such equipment with the pressure drops which could be expected through packed and fluidized systems; correlations proposed in the literature differed from each other frequently by as much as 75 to 100 percent. Because new processes, especially more recent modifications of the original Fischer-Tropsch process, must compete with old, firmly established processes on the basis of unit product cost, the pressure-drop correlations in the literature were considered to be too inaccurate for use in calculating the energy required to pass fluids through packed beds. The following study was begun in 1946 to develop correlations that would be suitable for the design of new equipment in which fluids are brought into contact with granular materials. To arrive at general relationships, systems were chosen that did not involve chemical reactions, and a, particular effort was made to give the correlations only in terms of quantities that are ordinarily available from general process and design specifications.

Jan 1, 1951

By Gregory R. Wagner

The Program of Mine Safety and Health Research described in this document reflects the continuing commitment of the Spokane and Pittsburgh Research Laboratories to focus on the most important areas where research can make a difference in reducing risk and improving safety and health for miners. It is the first program of work conducted since Congress mandated closure of the former U. S. Bureau of Mines (USBM) in the Department of the Interior and supported integration of the health and safety research function of the former USBM into the National Institute for Occupational Safety and Health (NIOSH). Organizational changes made FY97 a challenging year of transition. Ongoing research was reviewed and revised to reflect the new, more limited, health and safety mandate of the research laboratories. The mining industry, mine worker representatives, and interested government agencies provided broad input to assure that the research performed would focus on the most critical safety and health problems confronting mining today and which are expected to be faced in the future. The two laboratories worked to evolve coordinated programs of safety and health research, each with a special focus. The work of the Spokane Research Laboratory is directed toward issues of special importance to the Western mining industry, particularly those safety hazards found in metal/nonmetal mining and surface mining. The work of the Pittsburgh Research Laboratory will continue to focus on Eastern mining, particularly underground coal mining. Traditional areas of expertise for understanding and preventing fires and explosions and for controlling the hazards of dust and noise will continue to reside in Pittsburgh. Each laboratory is developing new capabilities in the analysis of relevant safety and health information to assure that program priority-setting decisions are informed by the best available data. Recognizing the continuing importance of communicating the results of research to all who are capable of improving safety and health conditions in mining, each laboratory has developed an activity for information dissemination and coordination with stakeholders. In the midst of organizational self-examination and change, the research staff in Pittsburgh and Spokane have never wavered from their continuing commitment to conduct the highest quality scientific research-solution-oriented scientific work meant to reduce the risk of injury, disease, and death from occupational hazards in mining. The pages that follow give insight into some of the program activities and accomplishments from FY97. I hope you share my pride in the many accomplishments of the NIOSH mine safety and health research program during this year. This report comes at a time of increasing stability for the mine health and safety research program. The organizational changes in Spokane and Pittsburgh have been concluded, and NIOSH has succeeded in recruiting a new, permanent associate director for mining to lead this critically important national program. Congress has contributed to an optimistic future by providing expanded funding for NIOSH mining-related research for the next fiscal year. On a personal note, I greatly appreciate the opportunity I have had to serve as the NIOSH Acting Associate Director for Mining during this transitional year. The commitment and intelligence with which the mining research staff pursued their mission was matched by their patience and understanding in moving into a new organizational environment. All of us committed to improved safety and health for this Nation's miners owe them our respect and appreciation.

By Walter C. Woodmansee

The only reported mineral production in 1977 was small output of alluvial gold, valued at an estimated $54,320.2 In addition, marine shells are gathered for use in lime manufacture, although output was not reported. Proposed development of a bauxite mine and smelter, involving Rennell and Vaghena Islands, was deferred in June. Conzinc Riotinto of Australia Ltd. (CRA), in partnership with Mitsui Mining & Smelting Co. Ltd., and the Solomon Government, with- drew from the project, and Mitsui, which conducted a feasibility study and metallurgical testing of the bauxite, decided to defer further work because of slack demand for aluminum in Japan and difficulties in arranging financing. The Mitsui feasibility studies reportedly indicated that the project could be viable despite technical difficulties and relatively high initial investment costs. The project was to produce 1.5 million tons of bauxite and 600,000 tons of alumina per year from reserves totaling 60 million tans at 45% to 50% A1203.

Jan 1, 1981

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization, and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available? in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number 50241073 by Fenix & Scisson, Inc. to the Denver Mining Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By R. S. Dean

"Applied Mineral Physics, by R. S. Dean.- This is an introduction to the seven papers that follow. It discusses the practical aspects of mineral physics and outlines the theo¬retical viewpoint underlying the investigations reported herein.Explosive Shattering as a Possible Economical Method of Ore Presentation By John Gross and C. E. Wood. - It is shown that explosion shattering by impact is favored by large charges and by low ratio of water to charge. For 400-gram charges of dolomite crushed through 48 mesh the steam costs are less than 5 cents per ton of dolomite obtained. This is within the range of present steam costs for ball-milling dolomite.Electrical Properties of Minersl Aggergates I. Natural and Artificial Aggregates Crystallized Lead Sulphide By R.S. Dean and John Koster - This paper deals with the electrical properties of natural and synthetic galena. It is shown that massive crystalline galena has a normal positive temperature coefficient of resistance, whereas fine-grained steel galena has a negative temperature coefficient, the curve R v. T being exponential in form. That steel galena behaves somewhat like a leaky condenser is indicated by ballistic and alternating-current bridge measurements. In determining the cause of the erratic results of alternating-current resistance measurements it was observed that the measured re¬sistance was a function of the current through the specimen. The direct-current resistance was found to be proportional to the square of a superimposed radio-frequency current and independent of the frequency.The influence of grain size or the amount of metallic interface on the voltage-current characteristics at various temperatures on synthetic galena pastilles was studied. It is proved that the volts v. amperes curves are linear for all sizes and temperatures, that they have an intercept which is apparently a linear function of the temperature, and that their slopes are exponential functions of the temperature and give rise to a negative temperature coefficient of resistance.Apparatus for determing the Magnetic Constants of Mineral Powders by V,H, Gottschalk,and C. W. Davis.- A modified isthmus permeameter having a spark-suppressed primary and a multiplier in the secondary circuit to regulate the effect of capsules functioning as a twin isthmus is used to obtain quantitative data and normal induction and hystersis curves from small amounts of powdered material at fields surpassing 3.000 oersteds. Data and curves are given to demonstrate the calibration of the apparatus and the reproducibility of its results. Applications and limitations of the apparatus are noted.Magnetization Curves for Magnetite Poeders by V. H. Gottschalk and F. S. Wartman.- This paper gives measurements on four lots of purified and analyzed magnetites in mixed fractions with especial reference to the variation of permeability with grain size and with dilution by an inert material."

Feb 1, 1935

By Stephen H. E. Phillips

This report outlines the modifications that have been carried out to the original prototype rectangular shaft sinking equipment for its use in a circular shaft. The surface testing of the machine is described where seven, 24 ft. diameter shafts were excavated to an average depth of 21 ft. at rates ranging between 1 ft/hr and 1.9 ft/hr depending upon the prevailing conditions. The durability and productivity standards for the equipment were established indicating that the objectives of the project had been realized. That is, when using the machine the sinking rates could be increased by 25% and costs reduced by a corresponding amount compared with conventional drill and blast methods. In addition it was shown that the machine had been developed to a state of fitness for sustained underground use.

Jan 1, 1981

By McHenry Mosier

The object of this investigation is to determine the field for the use of detachable bits in metal mines of the United States by correlating the data developed through the experience of mines using these bits. Most of the metal-mining districts in the Middle Western and Eastern States already have been visited. The purpose of the present circular is to define the problem and to discuss the factors that must be considered in order to determine, under different operating conditions, the advantages and disadvantages of this type of bit. Some of the data obtained to date are presented to emphasize points made in the discussion. It is hoped that, as the study progresses, a great many data on drilling will become available. It is evident that since in some cases these data will be confidential they cannot, therefore, be published except as they may be included in average figures covering several different mines. Some data already secured are of this nature, Although considerable information on drilling operations has been gathered at different mines, there were only a few instances in which there were available complete data on all the factors entering into the total cost of drilling with detachable bits and with conventional bits on regular drill steel.

Jan 1, 1936

By G. Hakes

A data bank on bolter technology was assembled which included state-of-the-art industrial equipment as well as new equipment currently under development for the U.S. Bureau of Mines. This information was augmented by field visits to selected USBM contractors, mine operators and others for the purpose of obtaining a thorough understanding of present coal mine roof bolting safety and productivity problems. These direct contacts provided valuable insight regarding requirements for new bolting equipment necessary to assure wide user acceptance. Using this background material and information, a series of roof bolter concepts was developed offering improved operator safety with minimum impact on productivity. The concepts developed utilize existing componentry and technology wherever possible. All of the concepts feature a fully protected operator station located 6' to 10' outby the active bolt line and the hazardous rotating machinery.

Jan 1, 1978

By A. R. T. Denues

The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives.

Jan 1, 1940

By A. R. T. Denues

The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining. In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives.

Jan 1, 1940

By J. G. Donaldson

Nickel containing less than 0.01 percent of total metallic impurities was produced at the Rolla Metallurgy Research Center of the Bureau of Mines by electrodeposition from purified electrolytes. The first report on this research4 described purification of electrolytes by selective precipitation and by liquid-liquid extraction. This second report describes a procedure: or electrodepositing high-purity nickel from electrolytes purified by passing a nickel ammine solution through a column of an ion exchange resin. The nickel electroplated directly from the ammine solution without further treatment; a titanium cathode and two platinum anodes were used. The nickel deposit was dense, smooth, and adherent, and contained less than 0.001 percent each of cobalt, copper, and iron, and spectrographically detectable traces of aluminum, magnesium, and silicon. Nonmetallic impurities in the nickel metal were carbon and sulfur, each present in concentrations of less than 0.01 percent. The results of several experiments planned to purify solid nickel salts by zone refining are also reported. These salts, after purification, were intended for use in preparing electrolytes for deposition of high-purity nickel. Results were not encouraging so that the more promising ion exchange procedure was emphasized chiefly.

Jan 1, 1962

By Thomas P. Mucho, David C. Oyler, Jim Pablic, Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to be abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1,000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By William H. Holley

Thirteen additional preservative/fire retardant systems were applied to Ponderosa pine and evaluated for flammability both before and after water leaching. The more promising four systems were given a thorough evaluation for flame spread, toxic gas and smoke density levels, resistance to decay, and compressive strength. The most promising system on the basis of history of usage in the mine, ease of application and low cost as well as overall performance is the Fyreprufe/ACC Albi 107A/ 144 combination. A survey of inspection tools and instruments, identified equipment which could be assembled into an inspection kit for use in determining the extent of decay and/ or impregnant retention levels in mine timber. A literature search identified those high fire hazard areas found in a typical mine. Timber and other wooden structures used in such areas should be treated with an acceptable fire retardant system. A survey of insurance companies revealed that the use of such treated timber in the mines would probably have little or no impact on the rate structure.

Jan 1, 1980

By Forrest T. Moyer

The safety record of the coal-mining industry in 1968 worsened appreciably .in fatality experience but was slightly better in nonfatal-injury experience. Work fatalities in 1968 totaled 311 and occurred at a frequency rate of 1.33 per million man-hours or worktime. The fatality total was 89 higher, and the rate of occurrence was 45 percent higher than the corresponding figures of 222 fatal injuries with a frequency rate of 0.92 in 1967. The worsened fatality record in 1968 resulted primarily from two major disasters (a single accident which results in the death of five men or more) which killed 87 men, nine in one and 78 in the second. The total of 9,639 nonfatal injuries was the lowest annual figure in complete records back to 1930. The frequency rate of 41.12 nonfatal injuries per million man-hours of worktime for 1968 was the second lowest annual rate of occurrence. The severity rate of all injuries, 10,513 days lost or charged per million man-hours, and the average severity, 248 days lost per injury, in 1968 were the worst annual data in the series started in 1944. Total worktime of 234.4 million man-hours and coal output of 553.3 million tons in 1968 were, respectively, 3 and 1 per- cent lower than in 1967.

Jan 1, 1972

By Sidney Katell

Philippine laterite and serpentine ores can be utilized in an electric furnace operation to produce both a steel ingot and a ferronickel product. Figure 1 is a schematic interpretation of a plant in which laterite and serpentine ores are processed separately to obtain both ferronickel and steel as products. A relationship of estimated capital requirements and probable returns has been established in this study for a plant of this type. No attempt has been made to evaluate the risks involved in commercial operations. At such time that the project might be constructed and placed in operation, changes in the costs of material, labor, and power may materially affect the profitability aspects of this study. One of the uncertainties involved in the economic evaluation is the cost of mining, handling, and shipping the ores. It is on this basis that the cost of ore delivered at the plant is assumed to be variable at $3, $5, and $7 per net ton (dry basis). For all other costs a plant site at Iligan City, Philip-pine Islands, has been assumed in preparing the economic characteristics for a plant that will process 2,000 tons4/ of ore per day. Results of the study, for the 2,000-ton plant, with all monetary values expressed in terms of United States currency (Philippine peso valued at $0.50), are summarized as follows:

Jan 1, 1962