Search Documents

To determine the relative permeability of the soil a series of percolation tests were performed at the three locations of interest at Lanse, i.e., 3C, 03A and strip bank, and KA and KB at Kato. Soil cores were removed to 2, 8, 16, 24 and 32 inch depths with the thin wall sampler tube, each core separated from the next by about fifteen feet. Then two-foot-long thin-wall tubes were inserted into the 2, 8, and 16 inch deep holes and three-foot long tubes were inserted into the 24 and 36 inch deep holes. Each tube was tamped down about one inch further to assure a bottom seal; the tubes were filled with water and the rate of fall was measured. The test is similar to those done for septic tank percolation studies 6; but is not quantitatively related to Darcy's coefficient of hydraulic conductivity because the water can flow in three dimensions from the bottom of the tube. The measurements are dependent on the length of test, since the rate of fall is a function of the head. Therefore, it should be noted that the 24 and 32 inch deep tubes should give faster percolation rates because of the one foot greater head. At locations 03A and 3C the data show a sharp decrease in percolation at increasing depth, Table XV. However, the percolation at 03A and 32 inch depth is much higher than at 3C (0.2 vs. 0.01 inches/hour); the fragipan layer must be deeper at the 3C location since this area does experience a perched water table. On the strip bank the rates of falling head are randomly variable, appearing to be as much dependent on the particular location of insertion as on depth of placement. For example, water drained from the 16 inch tube as fast as it was added, probably into a sub-surface cavity or crevice. At Kato the tubes were more difficult to place because of interference of tree roots. For this reason 2 inch deep tubes were not inserted. These short tests at Kato were inconclusive, varying extensively when the tubes were moved. Field permeability tests were also performed in two (previously described) eight-inch diameter permeater tubes at Lanse and one at Kato. Because the soil is confined inside the tube, hydraulic conductivity can be calculated according to Darcy's flow equation. The high values reported in Table XVI experienced when the tubes were rewetted from a dry surface condition, enable us to conclude that infiltration is faster than the saturated permeability of the soil. In contrast to the falling head percolation tests, these permeability results do not show a high variation between locations.

Jan 1, 1972

This chapter details the perspective from which collected data have been examined. The first part, intended primarily for lay readers, discusses several topics related to mining as an enterprise. Initially, the organizational functioning of atypical large mine will be described. It is the formal structure above a miner that decides the conditions of his or her work. A second point of concern is the technology itself An underground coal mine is a sociotechnical system, with workers and machines organized in particular ways during production. Third, general conditions and dangers underground will be described in detail. The physical environment of an operation is a powerful factor in the work life of miners. Fourth, a discussion of the process of formal training is given. During this training, a new worker is taught what the organization expects of him or her in the role of safe, productive, coal miner. Next, there are outside organizations that act as significant forces in the workplace. Examples include the Mine Safety and Health Administration (MSHA), State agencies, and the United Mine Workers of America (UMWA). The roles of these entities will also be examined. The second part of this chapter will depict each study site as a concrete setting, so that findings can be interpreted in their proper context. The Organizational and Technical Nature of Mining A coal mine is a complex system. It is defined as all parts of a mining plant's property (both underground and surface) that contribute, under one management, to the extraction or handling of coal [American Geological Institute 1997]. As suggested, many functions that must be carried out at an operation are only indirectly related to coal mining and processing. Even the jobs that are di¬rectly related tend to be numerous and varied [Wallwork 1981]. According to Palowitch [1982], the chief reason for this sophistication is that "after more than two centuries of exploiting our coal resources, today's coal industry finds itself saddled with a horrendous legacy of human impairments and environmental damages which society demands be corrected." Now, the effects of government regulation are evident in every aspect of the mining industry. Any operation, if it is to survive, must be administered with an eye for social efficiency and accountability. Long-range planning is needed to ensure that the mine produces coal in a cost-effective manner. One of the first things that must be considered is location and method of access. To extract coal from an underground mine, a coalbed (or "seam") must be reached from the surface. The term "portal" is generally given to any entrance that provides access to a coal mine. In hilly terrain, such as is found in Appalachia, the coal may "outcrop" on a hillside. This allows direct

Jan 1, 2000

Homans [1950] offered a working definition of group that is useful for this research: "We mean by a group a number of persons who communicate with one another often over a span of time, and who are few enough so that each person is able to communicate with all the others, not at secondhand, through other people, but face-to-face." This chapter begins with a discussion of the group concept in reference to the hypothesized escape groups mentioned earlier. It then moves to an examination of analysis techniques used by the authors. Finally, the subjects themselves are profiled according to their demographic characteristics. The Nature of Groups Warriner [1956] took a realist approach to understanding groups: "(1) the group is just as real as the person, but (2) both are abstract, analytical units, not concrete entities, and (3) the group is understandable and explicable solely in terms of distinctly social processes and factors, not by reference to individual psychology." Warriner's realist position merely holds that "group" occupies a different domain in which it is no more or less concrete than "person." At this group level the unit of analysis will be those relations that indicate social rather than individual behavior. It is possible to investigate these group properties empirically-if a researcher avoids confusing conceptual entities with concrete ones. Most people seem to accept that group attributes must somehow be inferred, but think personal attributes will be directly manifested, requiring little or no interpretation [Snizek 1979]. In other words, nobody would equate physical components of an underground working section with the actual work group, yet social scientists (as well as laypeople) very often confuse real individuals with notions of the person. In actuality, neither groups nor persons are directly disclosed to the senses; both are inferred by experience and observation. One can "see" a group just as clearly as one can "see" a person, given the proper perspective from which to do so. It is necessary, in developing this perspective, to begin with a sound definition of the thing being examined. Besides communication, or more generally, social interaction, Homans [1950] included three other components of group makeup. "Sentiment" is characterized as the feelings people tend to form about one another when they interact often. These feelings include not only friendliness and dislike, but attitudes such as approval or disapproval. A "norm" is an idea, held in common by group members, that specifies how people ought to behave in given circumstances. In lay terms, norms are simply those informal rules individuals abide by in order to get along together in social situations. Finally, "activity" refers to those things persons do with others. In work groups, as an example, many of the activities are cooperative and goal-directed.

Jan 1, 2000

The first steps in the process of mine evacuation are the recognition of a problem and an attempt to communicate the problem to miners who may be affected. This chapter will focus on the way that a problem, fire, came to the attention of mine personnel and the messages that were sent to miners in the affected areas. The concept of information uncertainty, which was introduced in chapter 4, will be discussed as it influences problem perception and diagnosis. Sociotechnical and interpersonal communications will be explored and suggestions for improving these systems will be offered. It might seem that the first indication of a dangerous fire would motivate individuals to take self-protective action, to evacuate the affected area or structure, and to provide clear warning to others who are in danger. Research has actually shown that in most situations this does not occur. Instead, time is taken to gather more information, confirm information that is provided, and consider possible alternative explanations that could account for the given circumstances [Canter 1990; Scanlon 1979; Bickman et al. 1977]. This process of confirmation can lead to the loss of critical time. Canter [1990] summarizes the problem in his book, which reports studies of a number of fire events: "As discussed throughout this book, ambiguity and confusion, incoherent instructions and time-wasting actions, lack of appropriate instructions and misunderstanding of the nature of the event that is unfolding, are all hallmarks of fires and emergencies that kill people." In this chapter, the detection of each mine fire and the communication of warning to endangered miners will be reviewed with an emphasis on how those processes were affected by the availability and use of information. Information can become available through a variety of mechanisms during an emergency situation. First, cues may be taken directly from the environment. Smoke is an obvious example. Secondly, mechanical devices, such as smoke detectors, may provide warning messages. A third source of information is interpersonal communications. These can occur face-to-face or through some mechanical device such as a telephone. With all three methods there is a possibility of miscommunication, misunderstanding, and misinterpretation. All of these means of communication were used with varying degrees of success in the three mine fires analyzed here. A fire, like any nonroutine situation, engenders uncertainty about a diagnosis and understanding of the problem [Mead 1938]. This uncertainty leads to delays in realization of the seriousness of the situation and therefore in the proper response to it. Delay in action is an important concern in any fire setting, but is even more at issue in underground coal mine fires. Mine fires are qualitatively different from structural blazes: workers' escapeways may be miles long; the seam height at many operations is so low that it is impossible to walk upright; access to underground workings is always limited to a few (sometimes only two)

Jan 1, 2000

By C. A. Herbert

"The Workman's Compensation Law of Indiana, enacted in 1915, amended in 1917, 1919, 1923, and 1927, and in 1929 named the Indiana Workmen's Compensation Act of 1929, provides for a weekly compensation for disability due to accidents of 55 per cent of the average weekly wage of the employee, to start on the eighth day of disability. Compensation is computed from a maximum and minimum weekly wage of $30 and $16, respectively. Thus, the maximum weekly compensation is $16.50 and the minimum $8.80; the total compensation paid is not to exceed $5,000.In addition to the compensation the employer is required to pay all medical, surgical, hospital, and nurse fees for a period of 30 days and may be required to pay such fees for an additional 30 days at the direction of the Industrial Board of Indiana. In the case of fatalities the employer must contribute $100 toward funeral expenses.The law also stipulates that ""the employer shall keep a record of all injuries, fatal or otherwise, received by his employees in the course of their employment,"" also that the employer shall report within one week of their occurrence all accidents that cause either the death of the employee or the loss of more than one day's work. However, no standard form is furnished or required by the industrial board on which the employer shall keep a record of accidents, neither is he required to report the time of return to work of the injured employee unless the period of disability exceeds seven days and the accident thus becomes compensable. Hence, no record is kept of noncompensable accidents other than the first report sent to the industrial board by the employer.If the employer were required to keep a complete and concise record of all accidents, in duplicate, on a special form either furnished or required by the board, giving all of the essential data in regard to the accidents, and if he were required to submit a copy of this record to the board at the end of the fiscal year, the data thus assembled would not only be of material assistance to the board, particularly in making up its annual report, but would also furnish information of much value in the study of accident causes and what may be done to remove them.Those industries that have made marked progress in reducing accidents keep such records, as it is only through a full knowledge of how accidents occur that intelligent steps can be taken to prevent their recurrence. Unfortunately, the mining industry as a whole in Indiana has not kept pace with many other industries in reducing accidents, and it is urged as an aid to improvement that a thorough and complete record of mining accidents be kept."

Dec 1, 1932

By E. V. Cilento, K. A. DiGregorlo, R. C. Lantz

A kinetic model was developed to describe the production of superoxide (02) by single pulmonary alveolar macrophages (PAM). Model predictions were compared to experimental results obtained from single rat PAM. The O2 - was quantified by measuring the reduction of nitroblue tetrazolium (NBT) to a diformazan precipitate (NBTH2) from video-recorded images of individual cells. The kinetic model considered three reactions: (1) the production of extracellular 0 - from the reduction of oxygen by NADPH oxidase using intracellular NADPH as the substrate, (2) the subsequent dismutation of o2- to from O2 , and (3) the reaction of o2- and NBT. NBT specificity for o2- was analyzed by comparing results in the presence and absence of superoxide dismutase (SOD) which catalyzes the dismutation of o2- to H2o2. Measured PAM heterogeneity was accounted for by varying the concentration of intracellular NADPH, its rate of depletion, and the concentration of intracellular NADPH oxidase in the kinetic model. Model predictions compared favorably with experimental results except when SOD was present. This discrepancy may be due to diffusional limitations since NBT is a relatively small molecule (818 MW) compared to SOD (34000 MW). In addition, the cell surface is both ruffled and negatively charged, which may introduce steric hindrances and/or electrostatic effects since SOD is also negatively charged.

Jan 1, 1988

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

Pulmonary inflammation is accompanied by increased microvascular permeability and leakage of plasma into alveolar spaces. Serum has been shown to affect superoxide (O2-) production from pulmonary alveolar macrophages (PAM) in vitro, and in some cases serum has been shown to be necessary for stimulation of PAM. An electro-optical method was used to measure O2- production from single PAM by measuring the reduction of nitroblue tetrazolium (NBT) to a diformazan precipitate (NBTH2) from videorecorded images of individual cells. PAM were stimulated by their initial attachment to culture dishes independent of serum. The addition of 2% serum to the culture medium increased NBTH2 production during attachment, whereas concentrations of 5 and 10% serum had no additional effect. In contrast, PAM incubated for 2 hrs could not be stimulated by phorbol myristate acetate (PMA) or zymosan particles to produce O2- unless serum was present during the incubation and/or stimulation; however, NBTH production was similar in all cases of serum addition. Also2, serum alone did not stimulate adherent PAM indicating that serum is necessary but not sufficient for stimulation of attached. PAM. These results suggest that changes in microcirculatory permeability may have a pronounced effect on superoxide production by PAM and that serum may help regulate or condition these cells during inflammation of the lung. (Supported by USBOM Gll35142.)

Jan 1, 1988

By T. F. Morse, R. Lundstrom, A. J. Brammer, D. Peterson, M. Cherniack, T. Nilsson, J. D. Meyer, E. Toppila, G. Neely, N. Warren

HAVIC is a collaboration of investigators from North America, Sweden, and Finland having a scientific mandate from NIOSH, to study the exposure response relationship between vibratory tool exposure and adverse health effects. Five cohorts, the Suomossalmi forest workers cohort, Volvo truck cab workers, Connecticut shipyard workers, and matriculating dental hygiene students and experienced dental hygienists have been under study. In the case of shipyard workers, there was survey and tool exposure data from 1988, although detailed subject testing was only available within the timeframe of the study. The truck cab assembly workforce was an inception cohort that had been followed from 1994 along with age-matched controls. The Finnish forest workers had cumulative health data on a cohort (n=52) that had been studied from 1976. For a subset of these subjects, there was detailed tactometry testing in 1990, 1995, and 2003. Accordingly, there was historical as well as new prospective data for the industrial cohorts. The Suomossalmi cohort was reassembled only for our study, which precluded follow-up evaluation and because of retirement is almost certainly the last time this historic group will be studied. The study features are: • Characterization of the exposure response relationship for hand-arm vibration through a study design, incorporating multiple cohorts, some having existing historical data, • Selection of cohorts to include different types of vibration: oscillatory (forest workers) impact (truck cab workers), high frequency (dental hygienists) and mixed (shipyard workers), • Inclusion of two inception cohorts: dental hygiene students and Swedish truck cab workers, • Methods for multi-site and historical integration A description follows. [ ] Methods The study included surveys, physical evaluation, and a selection of battery of “best tests” (cold challenge plethysmography, multi-frequency tactometry, segmental sensory nerve conduction velocity [SNCV]1,2,3) applied across groups to quantify responses to exposure. Exposure monitoring included exposure characterization through daylong data logging at the individual level. Workers at each site were instrumented with a microcomputer-based Vibration Exposure Monitoring (VEM) system, developed at the Biodynamics Laboratory of UCHC and about the size of a police walkie-talkie, to record user-specific tool-operating times, vibrations, and grip forces throughout all, or a representative part, of their workday. More specifically, data logging methods involved the direct monitoring of work cycles, involving tool operation time and measures of tool vibration, namely the root-mean-square (RMS), root-mean-quad (RMQ), and root-mean-oct (RMO), and grip forces, each calculated per minute. For this study, the questionnaire was homogenized with other vibration studies4,5,6. Cross-translation was directed by the multi-lingual investigators, and then reviewed by the study team. To extend comparability with future international studies, questions were also added from the Vibration Network (VINET) draft questionnaire, the product of a European

Jan 6, 2006

By M. Townsend, E. L. Petsonk, B. Fedders, M. Niggemeyer, H. Abrons, E. Daniloff, J. Griffin, K. Kinsley

In certain populations, nonspecific airway hyperreactivity (HR) is associated with increased respiratory symptoms and decreased lung function. We analyzed standardized pulmonary symptom questionnaires and pre-shift spirometry with methacholine inhalation challenge (Chatham, M. et al, Chest 82: 15) on 228 control workers (C) with no known exposure to occupational hazards, and 200 underground bituminous coal miners (M). M and c were similar in age, height, sex, and smoking status. HR (defined as >15% fall in FEVI after up to 5 vital capacity breaths of 25mg% methacholine) was found in 25% of M and 28% of C (NS). M showed higher% predicted FEVI (%PFEV) than c (M 107%, C 104%*). 28% of current smokers showed HR versus 22% of never smokers (NS). Current smokers showed reduced %PFEV but were not different from lifelong non-smokers regarding prevalence of HR. Subjects with HR showed reduced %PFEV, (HR 101%, not HR 107%*) but M and c with HR showed similar reductions. M had more dyspnea and chronic cough than c*. Hyperreactivity was associated with increased symptoms in controls but not miners. In our study, the prevalence of HR in coal miners was similar to nonminers, and did not explain miners' respiratory symptoms. * P < 0.05

Jan 1, 1989

To evaluate the potential for dust reduction, during blasthole drilling, of water or foam applied directly into the drill hole. Approach The Bureau of Mines tested a through-the-drill-steel water and foam injection technique in two noncoal mines to evaluate the method&apos;s potential for greater dust reduction. The tests were performed by drilling a series of blastholes for an entire face (a 90 minute time-period). For the first 45 minutes of drilling, foam or water was applied through the drill steel. Blowing ventilation was supplied to the entry about 50 feet from the face. The dust concentration measurements were made by a Real-Time Aerosol Monitor (RAM-I), and the data were read out on a strip chart recorder. The evaluation test results showed that the water or foam injection technique, when used on localized dust sources, can be an extremely effective dust control method. Small amounts of water used in this method have also allowed it flexibility to be used in water-soluble ores such as salt, gypsum, anhydrite, and trona. How The System Works Water or foam is mixed with compressed air (approximately 100-120 psi) with suitable metering systems and forced through the drill steel into the blast hole at the point of dust generation. Because the water or foam is applied at the source, minimal quantities of liquid are needed (0.2 to 0.6 gpm). These low flowrates are sufficient to just moisten the dust emerging from the blast hole, thus eliminating a major source of airborne dust. The wet drilling procedure also eliminates a second source of dust. With dry drilling, the dust from the blast hole falls to the floor. Since this can be a 15-ft drop or more, the impact can send the dust billowing up from the floor, adding to the airborne dust. With wet drilling, the moistened dust merely dribbles down the face.

Jan 1, 1982

The faculty, graduate students, and post-doctoral researchers are an integral part of the Generic Mineral Technology Center for Respirable Dust. More than fifty (50) scientists, engineers, and medical personnel are engaged in respirable dust research at five universities, The Pennsylvania State University, West Virginia University, Massachusetts Institute of Technology, University of Minnesota, and Michigan Technological University. The expertise, effort and contribution of these individuals has proven to be invaluable in the attack on respirable disease. Nationally and internationally recognized researchers in the areas of particle characterization, interaction of dust and lungs, dilution and dispersion, rock mechanics and continuing education lend their laboratory facilities, equipment and human resources to benefit the mining industry. The expertise and resources of the National Institute for Occupational Safety and Health--Division of Respirable Disease Studies is available through their relationship with West Virginia University.

Aug 31, 1989

By H. H. Schrenk

One phase of the Bureau of Minest work in the field of health and safety is the promotion of safe, satisfactory, and reliable respir atory protective devices. To insure that such devices will be available, the Bureau has established schedules of what it considers the minimum re- quirements for oxygen breathing-apparatus,3 gas masks, hose masks,5/ and mechanical filter-respirators (a schedule of requirements for hose- type supplied-air respirators is being prepared). Approval of oxygen breathing-apparatus is given by the Safety Division; approval of other types of respiratory equipment is given by the Health Division, both divisions being in the Health and Safety Branch, Manufacturers of respiratory protective devices may submit their equipment to the Bureau for approval under the requirements of these schedules. As a prerequisite to submitting a device for approval, the Bureau requires a statement that the device is completely developed and of the design and material that the manufacturer believes suitable for a finished marketable device; that the device has been

Aug 1, 1937

By Alla D. Mah

The heat of combustion of TaC0.996 was determined by oxygen bomb calorimetry to be -302.8 ±0.4 kcal/mole. The corresponding heat of formation of TaC0.996 is -35.4 ±0.5 kcal/mole, and the calculated heat of formation of TaC1.00 is -35.5 ±0.5 kcal/mole.

Jan 1, 1965

By D. D. Bolstad

This report describes the construction and use of a direct-reading azimuth protractor (DRAP) by the Bureau of Mines for measuring fracture orientations in mines, tunnels, or other excavations having a magnetic environment. The DRAP allows a rapid and simultaneous measurement of dip and azimuth of dip of a fracture plane. The instrument is rugged, lightweight, and easily constructible from standard hardware items. The DRAP can measure dip to within ±0.5° and azimuth of dip to within ±5° of corresponding values obtained with a Brunton compass.

Jan 1, 1974

Increase the recycling of critical and strategic materials by simplifying the indentification and segregation of scrap. Background Because the United States is dl-most totally dependent on imports of such critical metals as chromium, cobalt and nickel, Bureau of Mines research has been directed towards conserving these metals by increasing the recycling of the complex scrap materials that contain them. Experienced scrap sorters, using the traditional techniques of object recognition, spark tests, chemical spot tests, color, apparent density, and magnetic properties, can adequately sort a wide variety of alloy groups. However, the complex nature of new materials entering the scrap market has made sorting both more difficult and more important. Some new alloys contain so many components that separation by discrete alloys becomes a prerequisite for effective recycling. The Bureau has completed Investigations on two methods for rapidly sorting complex scrap mixtures. One method uses a combination of two low-cost instruments. The other uses a single sorting instrument. Both approaches are reported.

Jan 1, 1986

By T. Christos

The explosive oils, nitroglycerin (NG) and ethylene glycol dinitrate (EGDN), were extracted from dynamites by a halocarbon solvent and were then determined by high-pressure liquid chromatography. Separation was achieved by liquid-liquid chromatography on a column packed with Durapak-Carbowax 400/Corasil II and the eluted NG and EGDN were detected with a double-beam ultraviolet detector.

Jan 1, 1973

By H. H. Stoek

It would permit coal mines to operate continuously instead of intermittently . Intermittent operation increases the cost per ton for mining , and makes the yearly return to labor low . These conditions contribute to serious instability and unrest in one of the fundamental industries of the country and this can be changed only by coal buyers doing their part to insure steady work . The railroads are now required to transport the maximum amount of coal during the winter months when traffic is most interfered with by bad weather and when the maximum amount of coal is used by the railroads to handle other coal . The railroads now use nearly 30 per cent of the total output of coal . About one- third of their freight traffic is hauling coal , so that economy of fuel used by the railroads will produce a considerable gross saving .

Apr 1, 1920

To reduce needless paging of persons by all phones in a mine or mill, while retaining all-location page capability. Approach Standard pager phones of any manufacturer are modified to include the option of selective calling and message holding. How It Works All commercial mine pager phones presently rely upon voice paging via a loud-speaker. When a page is initiated, every phone in the system broadcasts the audible voice page, even phones in locations where the desired person could not possibly be. The advantage of this scheme is that whole-mine paging occurs. The disadvantage is that persons soon begin ignoring pages because they occur all the time, and most are for someone else. Also, it requires considerable battery power from all phones making it necessary to change batteries very frequently, even in phone locations where personnel rarely go. In addition, if a voice page is made and not heard, there Is no way to leave the message. Therefore, persons who at a later time come near a phone, have no way of knowing a page was made and was not acknowledged. This results in situations that often have a direct bearing on safety and productivity.

Jan 1, 1980

By BUREAU OF MINES

The Bureau of Mines in its investigations of respiratory apparatus for use in mines and allied industries, tests equipment that is voluntarily submitted by manufacturers in accordance with published schedules of tests. These tests are designed to insure that the equipment has the minimum require- ments for safety in use. Approval certificates are issued for apparatus that meets the bureau's specifications, and the memfacturer is permitted to mark his equipment with a seal showing that it has been approved as "Permissible." A complete list of permissible self-contained oxygen breathing apparatus, gas masks, and hose masks tested before July 1, 1930, was published in Bureau of Mines Information Circular 6362.1 The present list includes all equipment tested and approved up to and including April 1, 1931.

Sep 1, 1931

By Robert P. Vinson, John C. LaScola, Fred N. Kissell, Edward D. Thimon

The face ventilation measurement method developed by the Bureau of Mines involves releasing a small volume of tracer gas (SF6) on the off-curtain side of the working face at the start of the mining cycle. At the same time, gas bottle samples are taken in the immediate return airway. The gas samples are analyzed, and a curve is drawn of SF6 concentration versus time. From this curve, the percentage of gas removed per time is calculated. A curve showing a high percentage of the tracer gas removed in a short period would represent a well-ventilated face. The face ventilation measurement method was tested in a full-scale mine entry model. Subsequently it was used underground to evaluate the spray-fan ventilation system and in an MSHA test facility to test machine-mounted scrubbers. The method was shown to be a simple and effective way of evaluating face ventilation systems.

Jan 1, 1980